
Gutenberg · ebook 39318
Practical Bookbinding
by Paul Adam · English · public domain in the US
Practical Bookbinding by Paul Adam is an English public-domain text held from Project Gutenberg (ebook #39318). _Director of the Duesseldorf Technical School of Artistic and
Chapter XI.--School Books, Mounting Maps, Drawings, &c. 169
Conclusion 177
Index 180
List of Illustrations
Page.
Fig. 1 Glue-pot for heating by petroleum. 3
Figs. 2 & 3 Holding whilst folding. 15
Fig. 4 Lifting into the Press. 19
Fig. 5 Open sheets laid out for gathering. 20
Fig. 6 Sections fanned out for drawing out. 22
Fig. 7 Sections fanned out for pasting. 23
Fig. 8 Suggestions for mounting on guards. 25
Figs. 9-13 Suggestions for folding plates and maps. 26
Fig. 14 Collating. 28
Fig. 15 Rolling machine. 31
Fig. 16 Sewing frame. 33
Fig. 17 Arrangement on the sewing frame. 33
Fig.
18 Arrangement of threads in hollaendering. 35
Fig. 19 Small stapling machine for single sheets. 35
Fig. 20 Arrangement of staples in brochures. 35
Fig. 21 Arrangement of threads in old style of sewing. 41
Fig. 22 Arrangement of threads with double cords. 41
Fig. 23 Divisions for sawing-in. 42
Fig. 24 Machine for sawing-in. 43
Fig. 25 Suggestions for single and double end papers. 45
Fig. 26 Suggestion for double end paper with tear-off. 45
Fig. 27 Overcast end paper. 46
Fig. 28 Loops for attaching to frame hooks. 47
Fig.
29 Loops for taking frame keys. 47
Fig. 30 Suggestion for sewing on four cords. 48
Fig. 31 Suggestion for sewing on six cords. 48
Fig. 32 Suggestion for sewing two-sheets-on. 50
Fig. 33 Thread-sewing machine. 53
Fig. 34 Wire-sewing machine. 53
Fig. 35 Rotary guillotine. 54
Fig. 36 Lever guillotine. 55
Fig. 37 Top edge arranged for when trimming
three edges. 56
Fig. 38 Rounding the book. 57
Fig. 39 Rounding machine. 58
Fig. 40 Backing machine for small shops. 59
Fig.
41 Backing machine for large shops. 59
Fig. 42 Backed book arranged for trimming. 60
Fig. 43 Marbling outfit. 66
Fig. 44 Suggestion for sprinkling colour. 68
Fig. 45 Comb marbling. 69
Fig. 46 Suggestion for curl marbling. 69
Fig. 47 Bouquet or peacock marbling. 70
Fig. 48 Eye marbling. 70
Figs. 49 & 50 Arrangement of flat and rounded edges. 74
Fig. 51 Top edge arranged for gilding. 80
Fig. 52 Headband shears. 82
Fig. 53 Headband working. 83
Fig. 54 Board-cutting machine. 86
Fig. 55 Spring back.
87
Fig. 56 Boarded book. 88
Fig. 57 Section of edge rule. 89
Fig. 58 English style of lacing boards. 90
Fig. 59 View of the most general styles of binding,
showing the divisions of the work. (Table) 94
Fig. 60 Corners cut for turning in. 96
Fig. 61 Corners: Right and wrong. 96
Fig. 62 Paring with Offenbach or Berlin knife. 97
Fig. 63 Paring with French knife. 99
Fig. 64 Blocking press. 105
Fig. 65 Appliances used in blocking backs. 107
Fig. 66 Colour roller. 115
Fig. 67 Stuck-on gauges. 118
Fig.
68 Turning in the head. 121
Figs. 69 & 70 The head: good and bad. 122
Fig. 71 The pasted-down book. 125
Fig. 72 Treatment of tear-off. 128
Figs. 73 & 74 Simple line designs. 131
Fig. 75 Half-calf extra tooled in blind. 133
Fig. 76 Leather binding with simple design in blind. 134
Fig. 77 Simple gold tooling on sides. 135
Fig. 78 Tooled cover. 136
Fig. 79 Specimen of tooling done in the Duesseldorf
Technical School. 137
Fig. 80 Leather binding by Oswald Kob, Bozen. 138
Fig.
81 Cover with laurel motive done in the
Duesseldorf Technical School. 139
Fig. 82 Leather binding with fern motive done in the
Duesseldorf Technical School. 143
Fig. 83 Simple gold tooling on squares. 144
Fig. 84 Design in gold for squares. Tools by,
F. Clement Leipzig. 145
Figs. 85 & 86 Two designs in gold for squares. 145
Figs. 87, Three simple backs. T, d, B = Title; N, T =
88, & 89 Sub Title. 147
Fig. 90 Type-holder with centre position. 148
Figs.
91, 92, Four backs tooled in the Duesseldorf Technical
93, & 94 School. 149
Fig. 95 Group of backs tooled in Carlsruhe Technical
School. 150
Figs. 96 & 97 Two richly decorated insides done in the
Duesseldorf Technical School. 150
Figs. 98, 99, Four richly tooled backs
100 & 102 151
Fig. 102 Rich half-calf extra binding. 152
Figs. 103 & 104 Tooling on heads. 153
Figs. 105, Tooling on the edges of the boards.
106, & 107 154
Fig.
108 Motive executed in the Duesseldorf Technical
School. 154
Fig. 109 Case to protect book. 155
Fig. 110 Cut-out case. 155
Fig. 111 Book cover. 155
Fig. 112 Cover in case form. 155
Figs. 113 & 114 End papers for account books. 158
Fig. 115 Boards cut out at head. 160
Fig. 116 Suggestion for account book back.
K Pared edge; T Part to be pasted. 161
Fig. 117 Suggestion for account book back. 162
Fig. 118 Boarded account book. 163
Fig. 119 To show where turn-in is to be cut. 164
Fig.
120 Hand numbering machine. 165
Fig. 121 Suggestion for back of guard book. 166
Fig. 122 Pattern for dust flaps. (Leinwand =
Linen hinge.) 167
Fig. 123 Eyeleting machine. 172
Figs. 124-127 Showing stages of pinning down for stretching. 173
THE METRIC AND BRITISH SYSTEMS.
TABLE OF COMPARISON.
+-------+-----------+------------+------------+-------+
|Metres.|Decimetres.|Centimetres.|Millimetres.|Inches.|
+-------+-----------+------------+------------+-------+
| .001 | .01 | .1 | 1 | .039 |
| .002 | .02 | .2 | 2 | .079 |
| .003 | .03 | .3 | 3 | .118 |
| .004 | .04 | .4 | 4 | .157 |
| .005 | .05 | .5 | 5 | .197 |
| .006 | .06 | .6 | 6 | .236 |
| .007 | .07 | .7 | 7 | .276 |
| .008 | .08 | .8 | 8 | .315 |
| .009 | .09 | .9 | 9 | .354 |
| .01 | .1 | 1 | 10 | .394 |
| .02 | .2 | 2 | 20 | .787 |
| .03 | .3 | 3 | 30 | 1.181 |
| .04 | .4 | 4 | 40 | 1.575 |
| .05 | .5 | 5 | 50 | 1.968 |
| .06 | .6 | 6 | 60 | 2.362 |
| .07 | .7 | 7 | 70 | 2.756 |
| .08 | .8 | 8 | 80 | 3.150 |
| .09 | .9 | 9 | 90 | 3.543 |
| .1 | 1 | 10 | 100 | 3.94 |
| .2 | 2 | 20 | 200 | 7.87 |
| .3 | 3 | 30 | 300 |11.81 |
| .4 | 4 | 40 | 400 |15.75 |
| .5 | 5 | 50 | 500 |19.69 |
| .6 | 6 | 60 | 600 |23.62 |
| .7 | 7 | 70 | 700 |27.56 |
| .8 | 8 | 80 | 800 |31.50 |
| .9 | 9 | 90 | 900 |35.43 |
| 1 | 10 | 100 | 1000 |39.37 |
+-------+-----------+------------+------------+-------+
WEIGHT.
1 gramme = 15.44 grains.
28-1/3 grammes = 1 oz. avoird.
1 kilogramme = 1000 grammes = 2.20 lb. avoird.
LENGTH.
1 metre = 100 centimetres = 39.37 inches. Roughly speaking, 1 metre =
a yard and a tenth. 1 centimetre = two-fifths of an inch. 1 kilometre =
1000 metres = five-eighths of a mile.
VOLUME.
1 cubic metre = 1000 litres = 35.32 cubic feet.
1 litre = 1000 cubic centimetres = .2202 gall.
HEAT.
1 calorie = 3.96 British thermal units.
COMPARISON BETWEEN FAHRENHEIT AND CENTIGRADE THERMOMETERS.
+----+-----+----+-----+----+-----+-----+-----+-----+----+
| C.| F.| C. | F. | C. | F. | C. | F. | C. | F.|
+----+-----+----+-----+----+-----+-----+-----+-----+----+
|-25 |-13 | 5 | 41 | 25 | 77 | 65 | 149 | 105 | 221|
|-20 | -4 | 8 | 46.4| 30 | 86 | 70 | 158 | 110 | 230|
|-17 | 1.4| 10 | 50 | 35 | 95 | 75 | 167 | 115 | 239|
|-15 | 5 | 12 | 53.6| 40 | 104 | 80 | 176 | 120 | 248|
|-10 | 14 | 15 | 59 | 45 | 113 | 85 | 185 | 125 | 257|
| -5 | 23 | 17 | 62.6| 50 | 122 | 90 | 194 | 130 | 266|
| 0 | 32 | 18 | 64.4| 55 | 131 | 95 | 203 | 135 | 275|
| 1 | 33.8| 20 | 68 | 60 | 140 | 100 | 212 | 140 | 284|
+----+-----+----+-----+----+-----+-----+-----+-----+----+
To Convert:-- Degrees C. to Degrees F., multiply by 9, divide by 5, then add 32.
Degrees F. to Degrees C., first subtract 32, then multiply by 5 and divide by 9.
PREFACE.
Nowadays the bookbinder does not bind only those books given to him for this purpose as was the case in former years, for present conditions necessitate his undertaking many kinds of work which have little or nothing to do with the binding of books, particularly such as are connected with the making or finishing of printed matter and paper goods, or where pasting, gumming, and glueing are required, which, in their turn, are connected with paper and cardboard.
On the other hand, some branches of the bookbinder's craft have now become quite distinct, and have developed into special industries, and have so enlarged and extended that even their particular methods of working and technical terms have quite changed. Cardboard goods, leather goods, photo albums, maps, and even account-books are treated by particular firms as specialities.
As we must now keep within clearly defined limits, we shall treat here only the work of bookbinding proper as far as it is concerned with the making of the book for publisher, bookseller, and buyer, and also the making of account-books, whilst the other work given to the binder, commonly called "fancy goods," must be excluded. Editions de luxe, charters, illuminated addresses, &c., are likewise excluded, as they are quite apart from the ordinary work of the bookbinder, belonging solely to artistic bookbinding.
When any such work is required the intelligent worker will not be at a loss; besides, he will derive ample assistance from the illustrations for this class of work.
The parts of this little book have been so arranged as to correspond to our present-day division of work: preparatory work, forwarding, covering, and finishing. In England and France the various processes have for a long time been similarly termed, and although in Germany we could not follow their lead without any deviation, because our method of work and division of labour are so different, yet the basis of this arrangement has been used in this book.
Every text-book has some drawback, the greatest of these being that a practical demonstration on the subject is more helpful than the most detailed written description, and yet even in the latter a text-book is limited. For the rest, I have tried to be as brief and clear as ever possible and to avoid faults which I have discovered in my former writings of a similar kind.
Paul Adam.
Duesseldorf, Germany, 1898.
INTRODUCTORY REMARKS ON WORKING METHODS AND MATERIALS.
The bookbinder works with quite a large variety of materials which are mostly what we might call "half-made," that is to say, such materials as have already undergone some hand or machine process in order to make them fit for the work of the bookbinder. This is not the place to go into details as to the source of all these materials or the manner of their production: that may be seen in special treatises.
We separate into various groups the materials we use.
A.--MATERIALS FOR SEWING AND PASTING.
The bookbinder himself prepares his paste from wheaten flour and boiling water. Put in a shallow vessel, by preference a stone or enamelled metal wash-basin, the quantity of flour required for about eight days, pour in as much water as will make a mixture by soaking and stirring of the consistency of honey. Add to it boiling water, first slowly, then quicker, stirring all the time. It does not do to add the water too quickly, as that is likely to make the paste knotty or lumpy, because it cannot be stirred quickly enough and the gluten develops unequally.
If added too slowly, the starch is not heated quickly enough and does not thicken sufficiently or not quickly enough, and the paste turns out too thin.
Good paste, when cold, should not be stiff like pudding, but should be easily worked with a brush. In order to prevent a skin forming on the top whilst cooling, pour over the paste as much cold water as will cover the surface immediately after the mixing with the boiling water; this water is afterwards poured off.
In summer when the paste is made, and whilst still hot, add a few drops of turpentine and mix well; this preserves the paste and keeps off insects. The addition of alum to the paste tends to make it watery, besides having no preservative properties.
If required, paste may be thinned by adding a little warm water. Potato flour is often used fraudulently for making paste, but this should only be taken when it is possible to use it up quickly, and not for books, but only for fancy goods, as this flour does not possess great adhesive power and is unsuitable for leather.
Glue is made from the well-known cake glue. The best English glue, although the dearest, is the cheapest to use. Good glue whilst soaking in water should still retain a certain degree of stickiness, must not be greasy, and should have no disagreeable smell. Glue if weighed before soaking and afterwards dried and again weighed should give no perceptible loss in weight. Good glue should not have a disagreeable taste, and above all should not betray the presence of salt.
To obtain the proper consistency in glue for bookbinding, a quantity of the cakes is taken and sufficient water poured over it to cover well.
The next day the gelatinous mass is taken out of the water and dissolved in the glue-pot by placing the softened glue in a pot standing in an outer vessel containing boiling water. Glue should never be boiled nor placed directly on the fire, as that causes the loss of the best part of its adhesive property.
Glue and paste are generally worked with a brush. For paste a large hollow brush is used; this holds a large quantity of paste and covers a large surface. For glue a closer brush with a metal fastening is used, because here the hairs cannot be secured with pitch owing to the brush being constantly exposed to heat. On the paste brush there must be neither ring nor anything else of iron, as this used in paste would cause rust, and rust would give iron stains to light-coloured leathers.
For the same reason no enamelled vessel should be used for paste after the enamel has once been chipped or worn.
Laying the glue or paste on a material is called glueing or pasting. A zinc-plate is the most serviceable pasting-board, as the paste is easily washed off. Glue can be scraped or soaked off and used again.
Pasting-boards of mill-board or paper are hardly to be recommended, as their use entails a considerable loss of material.
Of other adhesive substances, dextrine, gum, gelatine, and isinglass are used for certain purposes. The two former are always used cold, the two latter warm. The former are dissolved in cold water; gelatine and isinglass are soaked exactly like glue, the water poured off, and then melted in the glue-pot.
Dextrine and gum are used by the bookbinder almost exclusively for pasting larger surfaces, and for laying on these substances a broad thin brush fastened with a metal strip is used.
Fig. 1.--Glue-pot for heating by petroleum.
To heat the glue and to maintain the heat a glue-heating apparatus is used. The upper part always consists of the glue-pot. The better kinds are made of copper or brass wrought or moulded in one piece. For the sake of convenience a partition is let into this pot so that thick and thin glue may be ready for use at the same time. The glue is not heated directly over the flame, but by hot water; to do this the glue-pot is placed within a larger vessel containing water, the glue-pot at the same time closely fitting to the outer rim of the larger vessel. This contrivance is placed over a petroleum, gas, or spirit lamp, which gives the required heat.
In some districts where brown coal is found, it is heated on a specially made contrivance with the brown coal waste.
The latest method of heating is by electricity. The apparatus necessary for this has been put on the market by the firm W. Leo, Stuttgart.
The majority of bookbinderies, large and small, use a strong linen hemp-spun thread for sewing, the strength of which depends upon the weight and size of the sheets to be sewn. As it is inconvenient to be obliged to be continually beginning a new thread or knotting, most bookbinders use a reel of thread. The so-called Marschall thread is the best.
The book is held together by cords, for which the so-called sewing cord is used. There are now special kinds made for the purposes of the bookbinder; these are lightly twisted out of a long fibrous material so that afterwards they can be easily undone for the subsequent necessary scraping out. Certain kinds of bindings are sewn upon tapes; strong raw linen tape of 1-1-1/2 cm. being the material most generally used.
For machine sewing, thread is generally used. Tinned iron wire, ready wound on spools, is also used. It is made in various sizes and used according to the weight of the sheets.
B.--MATERIAL FOR COVERING THE BOOK.
The real protection against outward injury to the book lies in the cover, the inside of which consists of boards more or less strong. Of the kinds on the market the bookbinder uses grey-board, which is made from waste paper and rags. It is grey, very tough, and flexible, but dearer than other raw materials.
Straw-boards made from straw and waste paper are cheaper, but less flexible, and are easily broken. They take a very high polish under the calendering machine and become very hard, and are therefore very suitable for some work if flexibility is not essential. They are generally used in all cloth binding.
So-called leather-boards are unsuitable, for, in spite of great toughness and pliancy, they are certain to cockle and always remain spongy. Wooden-boards are unsuitable for bookbinding on account of their small resistance, but are indispensable for fancy goods and portfolios, as they can be so nicely cut and are less liable to subsequent cockling than any other kind.
Besides these, yellow and blue boards are made. These are coloured to suit and serve quite special purposes, mostly fancy goods; but they also are not used in bookbinding, on account of their high price.
The thinnest boards are known as middles. This is a strong whitish material made entirely from waste-paper. It is used for lining backs, limp bindings, and in all cases where flexibility, together with durability, is required.
In finished work--books, fancy goods, maps--the boards are never left exposed to view, but are covered with paper, cloth, or leather. For the inner side of the cover of the book white or coloured paper is frequently used, note-paper of the smallest size being more rarely used.
All marbled or pressed papers are made in one standard size. Besides the end papers for inside of books, a figured paper has of late been made known as "litho printed" for fancy goods. This has been put on the market in the most varied kinds, and also with cloth-like impressions, under the names damask, brocade, and Leipzig end papers. The use of this paper has of late been almost discontinued. The dearest are those printed with designs in gold.
Cloth is more durable than paper, calico being mostly used. This is made in all colours and designs, and was formerly imported from England; but to-day German manufacturers produce a really good article. Plain linen cloth, black, green, or grey, sail cloth, buckram, mole-skin, and beaver are used in the making of account-books.
Silk is used in the bookbindery as end papers in extra work, and also for fancy goods and for lining boxes. The lower grades are seldom used, the better qualities being mostly taken.
To-day velvet is still used in the bindery, chiefly as a covering for portfolios, albums, and addresses, and except for metal clasps remains without ornamentation.
The bookbinder's best material, to which is given the choicest, most expensive, and most painstaking decoration, is leather in its various kinds. Sheep-skin, undyed or split and dyed, serves for school books and other cheap work. Goat-skin and morocco are better kinds, the latter being preferable both as regards price and quality.
Morocco is made from the skin of the goat. Morocco, Levant morocco, and maroquin all denote the same kind. It is a strong, coarse-grained leather imported from the Levant, very tough and durable.
Cape morocco, also called maroquin ecrase, is similar to this. This has a very large, artificially smooth-pressed grain, and hitherto has been higher in price than all other leathers.
Calf (matt or polished) is quite smooth and is only used for fine work.
Cowhide is similar to this, but of coarser texture, and is only used for leather goods, portfolios, and albums; for other work in the bindery it is not easily enough worked.
Celluloid is one of the latest materials used for covers. There is evidently a good opening for this in the wholesale manufacturies, stamped goods, and small fancy goods; whilst on the other hand it is of little value to the smaller shops, as it requires machinery for gilding.
C.--MATERIALS FOR DECORATING AND FINISHING.
For the decoration of our work, either during or after production, there will be a large variety of materials used. Colours are used for the decoration of the cut edges and the cut heads of books. The smooth, uniformly coloured edges are made by a body colour--carmine, scarlet, chrome yellow, silk green, indigo blue. All these colours must be very finely ground before using; the addition of a little paste or dissolved gelatine makes the colour adhere.
For marbling the edges Halfer's marbling colours are now exclusively used; these are to be had ready for use.
Amongst the binders' materials gold takes quite an important place.
Leaf-gold in various colours is supplied either by the gold-beater or the wholesale dealer. The colour most used at the present time is orange gold, which is about the same in tint as our current gold coinage. Red gold is somewhat deeper in tone. Green gold and lemon gold are considerably altered by an alloy of silver, and are sold cheaper.
Besides gold there are still other leaf-metals used, principally aluminium as a substitute for silver. The latter is still being used, but its unfortunate property of turning black will by-and-by drive it from our workshops. Bronze-leaf is also used for very small jobs in large quantities--makers' names on hat linings, ties, &c. Like silver, it is also liable to rapid oxidization, which takes place with especial rapidity upon leather.
Gold leaf is made in various sizes. The larger size, about 85 mm., is the best to use, whilst the very small sizes are better suited for some work.
As a ground-work for gilt edges, the so-called poliment (Armenian bole) is now generally used. This is cleaned bole, made into a paste, and applied in a solution not too thin.
To make the gold stick to the surface, glair or white of egg is used in all cases. It must be properly diluted according to whether it is to be used for gilt edges or hand-tooling.
Finished work, especially smooth surfaces, is improved by the application of varnish, and is at the same time rendered damp-proof. The so-called bookbinder's or leather varnish is used for leather, cloth, or pressed dark papers. Map varnish, also sold as photographer's varnish, is suitable for light articles, maps, placards, &c. At present, spirit varnish with its quick drying and high surface is almost exclusively used for this purpose. Turpentine varnishes are no longer generally used in bookbinderies; in colour printing copal and amber varnishes are used.
The ready-made headband is an article specially manufactured for the bookbinder. It is fastened on the book in suitable lengths to cover the place where the body and back of books join at head and tail. These headbands are to be had in the most varied styles, according to price and requirement. For ordinary work a cheap cotton is good enough, for fine half-calf bindings a silk headband is used if it is not intended to weave by hand a headband of silk thread for decoration known as a worked headband.
Besides the headband, the book-marker is required, generally a silk braid in bright colours.
It is often necessary to fix clasps to heavy books and also to the smaller hymn-books and prayer-books. These are made to suit all requirements and in various styles by firms making a speciality of this work. The stronger the metal used, the better the clasp and the easier for the worker to handle, as clasps of poorer quality are sometimes spoilt even whilst being fixed to the books.
Imitation metal fastenings are necessary for certain purposes, although their use is now considerably limited. These are the stamped metal rims and corner pieces, which are indispensable in the manufacture of sample cases, &c. The fancy goods with their decorated borders which were so popular at one time have disappeared from the trade; on the other hand, there has been a demand for fancy coloured cords made by twisting cords together.
D.--TOOLS.
The bookbinder's workshop of to-day presents quite a different aspect from that of our forefathers, even if we go back only 50 years.
The work benches as now found in small leather or jobbing shops stand near wide and lofty windows, each bench having a large drawer at each worker's place. Underneath, between the legs of the bench, there is a board fixed on supports upon which boxes containing colours or any other materials in use are placed within easy reach; and so that the board may not inconvenience the worker sitting in front of it, a semi-circular opening is cut at each worker's place. At each place there is a stool, somewhat higher than an ordinary chair, with three legs and a round flat seat. The legs are connected by strong bars for the worker to rest his feet upon.
Shelves for the larger tools are conveniently arranged on the walls, so as not to be a hindrance, but still within easy reach. A few smaller chests with drawers are required for the storing of smaller tools and pieces of metal ornament, &c.
A sufficient number of wooden presses, pressing boards in folio, quarto, and octavo, with the screw key, as well as the press jack belonging thereto, must be conveniently placed. The screw key is used when applying heavy pressure; the press jack serves as a support during certain work which necessitates laying the press on the edge of the bench. If we add a few larger and smaller cutting boards and a few sewing frames, we have completed the list of the large wooden tools.
The bookbinder requires very many small tools, even if we take into account only those necessary for ordinary shop-work. Iron rules and squares in various sizes, shears, knives, compasses and spring dividers, folders, files, pincers and hammers of different sizes, chisels, gouges, and punches.
The finisher's tools are: Gold cushion, gold knife, scraper, steel; and furthermore, for hand-tooling, letter-box, fillets, rolls, ornaments, and letters, all very fine and very dear tools, which must be kept in special cupboards and boxes so as to protect from possible injury. The higher the class of work done in the shop, the larger must be the stock of these tools.
These are the tools for general work and which no shop could be without; but what makes our modern workshop so different in character from what it was in former times are the many mechanical contrivances without the aid of which practical and profitable work is now inconceivable.
The most necessary iron ally of the bookbinder is the cutting machine, either with lever or wheel action, the former for light, the latter for heavy work. Machine manufacturers vie with one another in their efforts to introduce inventions and improvements; but to-day it would seem impossible to make a discovery likely to be of any importance.
The second most necessary machine is for cutting boards. Those with a wooden pedestal and table are not so much to be recommended as those made entirely of iron.
When gilding in large quantities has to be done, a blocking press is necessary; lever action is always to be preferred to the balance or rotary action, the latter being of advantage for blocking or relief work, and also for fancy paper work. Even the best blocking press has some drawback; to be of any value, it necessitates quite an arsenal of plates and dies for blocking, and also calls for the constant replenishing and renewing of the same.
The standing press is used for heavy pressure applied to large batches of books. An iron press with two uprights will be found sufficient even for heavy use in most bookbinderies.
The rounding machine is now out of use. The binder rounds the back of the book with a hammer, and then it is backed in a backing machine, which puts the ridges on both sides of the book. The latest machine now being used in some of our large binding shops for this purpose is called the rounding and backing machine, which completely rounds and backs the book.
The rolling machine of to-day is lighter than were the first models of this machine; besides, the work is in many cases unnecessary, as modern printed books are generally carefully rolled before they leave the printer.
The wire-stitching machine came into use in England about 20 years ago, but is now abandoned. The wire-stapling machine is used for pamphlets, school-books, &c. Eyeleting and round-cornering machines are smaller appliances, whilst the backing machine mentioned above is a very useful ally. Machines for scraping and paring leather are used least of all, as there is little for them to do in a small bookbindery.
The foregoing is not an exhaustive list of our tools and machines, but we will bring to a close these introductory remarks on the usual appliances, as mention will be made of the others in their proper place.
PART I.
FORWARDING.
CHAPTER I.
GENERAL PREPARATORY WORK.
Books reach the bookbinder either in the sheets just as they left the printing press or folded and stitched. This folding and stitching is, of course, part of the binder's work, so we will begin with the sheet as it left the press; this sheet must in the first place be folded ready for further manipulations.
By folding we mean the arranging of the parts of a sheet in the order of succession required for reading. To facilitate this work the printer marks not only the page numbers on each sheet but also gives each sheet a number, these numbers being known as signatures. Every sheet is printed on both sides; the front side is called the first side, the other side the perfecting impression. Both sides are marked by a number or (more rarely) a letter.
This mark stands at the right-hand side at foot of first page and is called the first signature; the second signature takes the same position on the second side of the sheet, that is, on page 3. Take any book haphazard and you will find the true signature on the first and the second signature on the perfecting impression, always in the same position. In order to show at a glance whether the signature is the first or the second, the compositor adds an asterisk, thus--
1 1* or A A*
first second first second signature.
We will see later that there is still another reason for the signature in the place mentioned.
When the sheets are to be folded, all the sheets of an impression are laid one on top of the other and all lying the same way. The modern quick-printing presses gather the sheets automatically, so that a sheet is rarely laid the wrong way, excepting through want of care in looking over them, or in the knocking-up in the printing office a few sheets or a whole batch are thrown out of order. According as we are dealing with folio, 4to, or 8vo format we must order the gathering of the sheets and, of course, the position of the signature. The commonest format is 8vo, that is to say, the size which gives eight printed leaves (or 16 pages) to the sheet.
At the same time, the method of folding this format is the most economical and includes the others as well.
When folding 8vo sheets the pile lies in front of the worker in such a way that all the second signatures lie uppermost at the foot of the outside right page and all the first signatures at the left on the under side of the sheet; or, in other words, all first-side leaves are turned face downward and perfecting impressions face upward.
Printed sheets are never folded according to the edges of the paper, but always registered by the printed columns or the page numbers. The novice finds this by holding the sheet against the light, but the experienced worker is able to fold the sheet without so much as lifting it from the table.
Figs. 2 and 3--Holding whilst folding.
The manipulations for the folding of an 8vo sheet are as follows: The right hand holds the paper-folder and creases down the folds, the left gathers the sheets and moves them about aided by the right.
1.--The right hand takes hold of the sheet at the right a little below the middle, brings it over to the left, when it is taken by the left hand and properly adjusted according to page numbers or corner of printed page (Fig. 2).
2.--Crease with folder from bottom to top (the folder is held slanting to the crease, but the edge is used).
3.--With the right hand the right and the left hand the left of the folded sheet are taken hold of at about the middle of the longer sides, nip together, make a short turn so that the left hand brings the sheet with its fore-edge to the folder's body, the left hand lets go, takes hold of the sheet between both ends at the middle fold, and adjusts pages and edge of fold alike (Fig. 3).
4.--The right hand creases from top to bottom.
5.--Left hand turns sheet over to other side, both hands take hold as before, nip together last fold, and adjust pages and fold.
6.--Crease from top to bottom, laying aside sheet to left, fold lying to right.
The whole process, which demands considerable dexterity, is only to be thoroughly learned by example and imitation; but study the illustrations, which are correctly drawn from life.
This is the way sheets are folded when they come direct from the press; but if they had already been folded in quires, as is usually the case with school and hymn books, the sheets would simply be folded in the middle for convenience of storage and despatch.
In this case the quires must first be opened, the crease taken out, and the sheets laid open. This work is called "breaking the backs." The unfolded sheets are folded in exactly the same manner, but before the last crease the sheet is turned, creased from bottom to top, and put aside in such a way that the sheet is turned over, that is face downwards. If this precaution is not observed, the folded sheets would afterwards be found in wrong order.
At this point we might remark that the top, both of the book and the single page, is called the head, the bottom the tail. These commonly used terms will very frequently crop up.
The folding of a 4to sheet is exactly the same, excepting that the last fold is omitted; the second signature lies face upwards at top on the right, the first signature lies downwards at top left hand.
Folios are made up but rarely nowadays, except in artistic editions de luxe, Bibles, and missals; they are simply folded in the middle; the signatures appear as in 8vo format.
Duodecimo format, that is, a sheet printed to make 12 pages on each side, is so printed that the third part of the sheet has to be cut off with a knife or machine. This work is done in various ways: the sheet may be folded without regard to the one-sided elongation; after folding the part is cut off with a knife or machine at the proper place and the detached portion inserted in the middle of the main section; the small section is therefore called "the inset." On the other hand, the inset may be cut off before folding and then separately folded and inserted.
This is the more usual method.
The cutting off of the inset prior to folding can be done in such a way with the modern quick-printing presses that the sheets are adjusted and cut off in the machine, or they may be folded in sections of six--eight sheets and cut open in the fold. For cutting open such sections a very sharp knife is required, either the usual bookbinder's knife or, better still, a somewhat longer two-edged paper-knife rounded at the end.
Formerly, when printing was not done with such accuracy as now, the sheets were folded into sections by means of points. The compositor made a point on both sides between main sheet and inset in the furniture where the division had to be made; if pins were stuck into the table through these points each of the sheets following could be placed on the pins.
Thus all sheets are brought to perfect register and may be cut with knife and rule or machine exactly through the points. This work is called "working to points."
The detached portion appears as a long printed slip upon which are four pages or columns side by side. They are folded in a very simple manner.
The page on the right is brought over to lie on the page to the left, registered, and creased in the middle, and the double sheet is now folded once more in exactly the same way.
Inserting is done as follows: The sheets for insertion are placed to the right, the main sheets at the left side of them; the right hand takes a sheet to be inserted at about the middle of the fore-edge, the left hand at the same time taking a main sheet in such a way that thumb, middle, and index finger open the sheet about the middle of the upper fold, and raise it so that the right hand can easily slip in the insertion.
Whilst doing this, the left hand slips to the back, where the forefinger manages the adjustment of the sheet inserted. The insertion is nicely fitted into the back and must lie close to it. This work is also very easy, but it also is much easier to learn it from example and imitation than by written instruction.
If the insets were already arranged before folding, that is to say, had the sheets been arranged according to page numbers immediately after printing as before mentioned, strict attention must be given to see that each main sheet has its insertion, otherwise the page sequence would be thrown into confusion in binding.
In folding, every fold must be sharply creased down; but a firmness of body in the sheets, a smoothness of the single sheet, and a proper sharpness in each separate fold can only be obtained by pressing the sheets. For this purpose the sheets must first be "knocked up," that is, they must first be adjusted at head and back by knocking them together on the table. Sheets are never pressed without being counted at the same time; this is done both for convenience in pressing and for checking the work.
Knocking-up can only be done upon a firm level surface; the beginner had better not take too many sheets at one time, say from 20 to 25: these are moved to and fro between the palms of the hands so that the back fold and upper fold are worked in turn, and at these sides the sheets are brought into line.
Knocking-up proceeds quickly if the sheets are handled lightly and freely. The single batches thus levelled are brought together and they in turn knocked up in the same way. Care must be taken that single sheets do not hang back, i.e., that all sheets come up to the levelled edge.
The knocked-up sheets are counted off--thin paper in hundreds, thick paper in fifties. To do this any big lot is taken hold of with the right hand--one soon learns to judge the quantity to be taken by the fingers--by the fore-edge, giving the hand a turn so as to bring the backs uppermost, when the sheets will fan out at the back and thus make the counting an easy matter. The left hand counts--pardon, the head counts, but the left hand tells off the sheets in such a way that the middle and index fingers are alternately inserted in 4, 8, 12, 16, &c., whilst counting 1, 2, 3, 4, &c., and at the same time throwing over the sheets held.
Every 25th lot of four sheets gives 100, and, of course, any other number you please can be counted in the same manner. Each lot is once more knocked up, placed in piles crosswise, and afterwards pressed.
Fig. 4--Lifting into the Press.
The contrivance for pressing most generally used nowadays is still the bookbinder's little wooden hand-press, with wooden, or perhaps iron, screws; the former are lighter and handier, the latter heavier but more durable and therefore of advantage where heavy pressure is demanded.
Each lot is placed between pressing-boards; these are about 1-1/2 cm. thick and vary in length and width according to the sheets or books to be pressed. According to the grain of the wood we speak of long and cross boards. On top of the upper and underneath the lower batch we place a cross board; it does not matter which way the grain runs in the other boards used. This precaution is taken to obviate the probable breakage when the cheeks of the press run parallel with the grain of the two outer pressing-boards.
The pile of sheets between the pressing-boards is so placed that the nuts of the press are at first raised as high as the pile about to be pressed requires, then the press is put on the table to the right in front of the worker so that the head of one screw at the front touches the table edge. The pile is drawn on to the front edge of the table, the left hand slips underneath, and the chin presses on top. Whilst raising the upper cheek of the press with the right hand, the pile is inserted between the opened cheeks, is adjusted, and the press screwed up, first by the hand screws and then by the screw key used for this purpose.
To do this the press with its high cheeks is held firmly between the legs and the nuts screwed up with the screw key as tightly as ever possible.
At this stage we might mention a work which is very frequently done in the printery, but seldom in the bindery: this is the so-called gathering before folding. This work, as we have already mentioned, is done so that printed matter for publication can be properly stored or prepared for sending away.
Fig. 5--Open sheets laid out for gathering.
The sheets are taken just as they left the press and piled up side by side in a row in order of number on a long table, each pile of sheets in exactly the same position as the others and just as they would be placed for folding; that is to say, for 8vos the first signature at the bottom left-hand side underneath, the second signature being at the bottom right-hand side on the top.
Generally the work is gathered in batches of 5-6 sheets. The sheets in question are then laid out (see Fig. 5).
The worker takes a board the required size, upon which he places the sheets when gathered; he begins at No. 1 pile, takes off the top sheet, being very careful not to take two, lays it upon the board, and so he goes the length of the table, taking the top sheet from each pile. He lays the pile of gathered sheets on the end of the table or another table standing behind. They are there received by another worker, knocked up, and folded in the middle.
If only one worker can be spared for the job, the gathered sections are placed to one side, but each is laid crosswise over the other so that they are easily picked up afterwards for knocking up and folding. If the work has more than five or six sections, the separately gathered sections must be afterwards again gathered in the same manner. Perhaps there may be placed in the last section parts of a sheet--the title, addenda, corrigenda, frontispiece, diagrams, &c. The treatment of these will be dealt with presently (pp. 22-24).
Sheets so gathered must be afterwards opened out for folding in the bindery. The section is opened, the crease well pressed out, and the whole smoothed down quite flat, care being taken that all sheets lie the same way, the opened sections lying side by side according to the signatures.
Before the folded sheets are arranged or gathered, there is frequently still some pasting to be done. The title, for instance, is seldom printed with the first sheet, but is usually made up with the preface, contents, &c., after printing the last page, often as part of the last sheet.
On this account the last sheet must be examined before folding to see how it is composed. If it happens that the sheet is to be exactly halved, it is best to cut the sheet in the middle and fold each half separately. It is even worth while cutting the sheet into quarters if the sheets can be pinned on, because it is then possible to fold the cut sheets in lots of five or six and to draw out each one singly, as it is commonly called "pulling out."
This pulling out is very easy work; each folded batch is separately opened in the middle, fanned out with a paper folder so that each sheet stands back about 1/2-1 cm. behind the other, and the batch folded together again; it would then appear as in Fig. 6.
Fig. 6--Sections fanned out for drawing out.
Take the batch lightly between the finger and the thumb of the left hand, and with the right draw off the sheets from the top one by one, knock them up, and firmly press down the back fold.
Every part of a sheet which after folding makes less than four pages (equal to two leaves) must be pasted on. To do this the parts to be pasted are fanned out from the back with the pasting side uppermost, that is to say, the sheets are fanned out with the folder in the same way as described for "pulling out," until they lie like steps or stairs, each sheet displaying an edge of about 3 mm. In this manner all sheets so lie upon each other that each is about 3 mm. behind the one under it.
The narrow margin is pasted; to avoid pasting more than the proper margin of the top sheet, a piece of waste paper should be laid on top at the right distance from the edge. Each leaf has thus a narrow pasted edge by which it is secured to the main sheet. So that the pasted edges do not stick together whilst each sheet is being fixed in its place, which, of course, takes time, the batch is taken between the fingers immediately after pasting, and by a few light movements the sheets are worked a little further apart.
Fig. 7--Sections fanned out for pasting.
Take the batch at A between the finger and thumb of the right hand, at B in the same way with the left; the upper leaves slip gently backwards if the right hand bends the batch lightly upwards so that the sheets are pushed to B, the left first allows the sheets to slip back and then holds them firmly so that the right may repeat this movement several times.
The batch is then so placed across the table that it lies to the right of the worker with the pasted edge away from him, whilst the pile of sheets to which the parts are to be pasted lies to the left, also with the back edge away from him. Leaf after leaf is taken up, carefully adjusted to back and upper fold, and pasted on to the main section and lightly rubbed down to right and left with the finger-tips, putting aside to the left each sheet as finished.
Under certain conditions, the pasting on of a so-called correction may be a very disagreeable task. If errors have been made in composing or printing a page which escaped notice and correction at the proper time, a revised page is printed, and this must be inserted by the binder in the place of the faulty one. This inserting is done after the folding; the faulty leaf is so cut off that a narrow margin is left in the back to which the rectified leaf is pasted.
If maps or plans accompany the work these also must be inserted; thin sheets need simply be pasted on the back edge like other sheets and fixed in their right place; but thick paper is not easily pasted on and, besides, would always pull away the next leaf. It is therefore joined to a narrow strip of paper about 1 cm. in width and this is pasted and fixed in the back. If several plates have to be inserted at the same place, or to be fixed at the end of the book, they are joined together in sections of suitable thickness. For this, thin paper is hinged in the back of the book, that is, the two plates are pasted over each other after pasting a narrow margin of about 3 mm.
When dry, the double leaf so obtained is folded together in the middle of the pasted little guard.
As this process lessens the leaf which has the back-fold by as much as is pasted to the other, the latter is cut down by 3 mm. beforehand.
If there are many such plates to be joined together, they are made up in sections of 4 or 6 according to the thickness of the paper, and every 2 or 3 cut down according to circumstances, and the same number left the full size. When all have been properly cut, the edges are fanned out and pasted. Then as many as make up a section are taken up and fanned out a little further, the pasted edge of No. 1 is laid on 6, 2 on 5, 3 on 4, and the batch set aside on the left and the same process gone through with the next lot. When dry, the plates thus guarded together are creased together at the back.
Plates on thick paper must likewise be mounted on strips of paper. These are cut from thin, strong note-paper and are so arranged that their thickness in the back is the same as the thickness of the plates. It is well to select a paper which when double is as thick as the plates. In case the plates are extra thick, the guard is made four-fold. The width of the guard must be measured to correspond. If a guard of double thickness only is required for filling up, it is cut twice the width of the guard and 3 mm. added for pasting on the plate. This gives 2 x 1 cm. + 3 mm. = 23 mm. If a guard of four-fold thickness is necessary, the result is 4 x 1 cm. + 3 mm. = 43 mm.
The plates are fanned out narrowly with the back edge uppermost, pasted, and each plate affixed to one of the made guards. This work is called "mounting on guards."
When the pasted plates are dry they are folded in the back on the following plan according to whether the guard must be two-fold or three-fold.
Fig. 8--Suggestions for mounting on guards.
Thus the folded guard completely fills out the space in the back of the book. Besides, two, three, or more plates can easily be made into a section if the little guards are made up within each other.
Despite this levelling work, the pasted part will still be noticeable; the thoroughly dried sections are therefore taken in batches of four or five, knocked up at the back edge, and the thick part carefully hammered on a stone or iron bed.
Just as paper strips have been used in this work, linen can be used for guarding atlases and mounting large maps which are intended for long and constant use. To fill out the back, cardboard or thick drawing-paper the thickness of the plates (or, if anything, a little less) is used. Of this material strips are cut 1 cm. in width and same length as the height of the work, cutting a strip for each plate of course. Besides these strips, cut some soft white calico into strips 3 cm. in width.
These are pasted, laid quite straight upon a clean board, two strips of paper are placed in the centre side by side on top of the pasted strip, and at right and left of each a map is hinged on, the first face downwards, the second face upwards. When dry, the section so made is creased in the middle, knocked down with the hammer, and pressed for a time. By this method two plates are hinged on each guard; by the other each plate had its own guard.
Many books are issued with plates larger than the format of the book itself; they must be brought to the right size by folding, but in such a way that the folded plate is secure from injury during any subsequent trimming.
Before making a single fold in the plate, the worker should clearly see his way through his scheme for folding, so as to bring the plate to the size required with the smallest possible number of creases. Plates which are slightly wider and longer than the size of the book are easily made to fit if they are folded once or, if necessary, twice across the middle, pasting the edge of one fold on a guard and then fixing in its place in the book.
Figs. 9-13--Suggestions for folding plates and maps.
If this will not do, the plate must first be folded up from the bottom edge far enough to escape damage in trimming, and then the long side must be similarly folded. Larger plates must take more folds, always working on the principle that the length of the book should first be obtained in the best possible way, and afterwards the width is taken as the guide in making the folds.
In doing this the plate must be folded now to the front, then to the back, so that on drawing it out it opens in a zigzag fashion. For the sake of clearness we give illustrations showing the most general methods of folding. The part marked A is secured in its place in the book by mounting on a paper guard; but one may, by cutting out the map properly, leave a small margin which will serve as a guard as shown in Figs. 10, 12, and 13.
In all cases, however, it is essential that the thickness of the folded plates should be equalised by inserting guards in the back of the book.
Formerly, when several plates were inserted one after the other, it was customary to place them in such a way that they were trimmed at top and bottom alternately; now they are placed so that they are all trimmed at the top edge: this is much better, because it keeps the top edge smooth and close, thereby keeping out dust and insects. The accompanying sketches are based upon this principle.
The so-called two-page illustrations in periodicals must be treated in the same way. These are only possible in the middle of a section, where they would be caught into the back and injured if the following precaution were not observed. Such illustrations are taken out, the back edge pasted, and then placed in the back so as to adhere to the following sheets, projecting about 1/2 cm.
The printed sheets thus treated must now be collected by the same process--that is if they have not been gathered in open sheets in the printery--into volumes; this work is generally known as gathering after folding.
As in gathering open sheets, the piles of folded sheets are placed side by side; but as these take up so much less room than the open sheets, in most cases the whole work may be laid out at one time.
Clear the longest table procurable, which if not long enough must be extended by the addition of small tables, trestles, &c., upon which are laid the batches of sheets in fifties, and, beginning with the last sheet, work up the row until the title page is reached and the gathering ended.
Starting from the left, the gathered sheets are placed to the right; after the last sheet, i.e., the title page, there should be sufficient room for placing the gathered sheets and also, if possible, for knocking up and collating, that is, checking the sequence of the sheets. The gatherer begins with the last sheet on the left, draws the top sheet with the right hand on to the left hand held flat to receive it, and so goes along the row, drawing from each pile one sheet, which drops into its place on top of the preceding one in the left hand.
This work can be carried on simultaneously by several persons following each other, but there must be a sufficient number of persons stationed at the end ready to knock up and collate the gathered sheets. In order to simplify this work and to enable one to take up the completed gathering at the title page, the pile containing the title page sheet is plainly marked across the back with a blue or red pencil, so that one sees on the back of each single sheet a coloured mark easily seen in the gathered and knocked-up sheets.
Fig. 14--Collating.
To collate a book it is taken in both hands. Taking a good hold of it by the right hand at the top edge, it is lightly held by the left at the bottom towards the back. Now make a turn downwards with the right so that the whole pack of sheets springs upwards and spreads out at the back like a fan, and the controlling left hand lets them go one at a time, whilst checking the sequence of the signatures, that is to say, the sheets must be checked to see whether instead of the right signatures following in due order there is not a second signature or perhaps none at all. In such a case the sheet must be taken out and re-folded.
It may be well to refer now to another more detailed branch of this work which is necessary for certain purposes. If books which have already been used or bound are sent for re-binding it would be very unsafe to rely upon the pages being in proper order, especially if they have been much torn and have to be mended. Very frequently the leaves of a section have been misplaced.
In such cases the book is laid flat upon the table, the head lying to the top, and, beginning at the title, leaf by leaf is lifted with the point of a knife after the way some ignorant persons have of using a moistened finger. The knife point is not inserted under the leaf lying uppermost but is lightly placed at the top of the leaf near the page number and the leaf pushed up from the side so that the left index finger takes it as it separates from the succeeding leaf whilst the eye scans the page numbers 1, 3, 5, 7, 9, &c.
Also with other things that do not admit of any other method of collating, e.g., ledgers, documents, &c., this is the only possible way of doing it.
Nowadays, paper received in the printery has been so well calendered beforehand--that is to say, polished between rollers--and after printing the sheets are once more so well rolled that the gathered sheets may at once be prepared for sewing. Old paper, however, must be beaten or rolled to make it firm and solid. The former work will be completely forgotten at no very distant date, as the younger generation of masters and men show less and less inclination to learn it.
For beating, a stone about the height of a low table, and a surface about the size of a sheet may be used, or a cast-iron plate about 6 cm. in thickness embedded in a block of wood the same height as the stone. Upon this firm base--which, of course, must stand on the ground floor or in the cellar--the book, or section of it if too thick, is beaten with a short-handled iron hammer, the face of which measures about 100 sq. cm. All corners and edges are well rounded off, and the face is slightly convex.
The handle must be short, not above 12 cm. long, cut oval, and just thick enough to be well grasped. The hole in the hammer is made so that the handle drops a little at the (outer) end.
In beating, the sections should be held by the left hand after being knocked up. In order to prevent injury to the paper, the sections are placed between pieces of waste paper of same size, also a mill-board or piece of waste paper to size is laid upon the beating stone. The right hand wields the hammer, which must strike the sections (or book) fairly and squarely with the full face. The beating is begun at the edge, and blow after blow is given in gradually lessening circles until the centre is reached, the left hand, of course, keeping up the necessary motion of the sections.
It requires considerable practice to do this without shifting the sections, but if this happens they must again be knocked up.
The experienced workman knows by the touch where the book has been beaten much or little and works accordingly. The main thing in this, as in all other work, is that the book should be again pressed for some time--for a night at the least. The beaten volumes are divided into several lots or sections about a finger thick, and pressing-boards placed between them. If any sections show folds or creases even after pressing, they must be once more beaten and pressed.
Fig. 15--Rolling machine.
The work of beating, as already said, has been almost entirely superseded by the rolling machine. In treatises by theorists, one finds over and over again that books are not so well bound nowadays owing to the "practice of hand-beating being discontinued." This opinion is absurd, and arises from a very superficial technical knowledge and wholly imperfect acquaintance with the requirements of our craft.
A machine-rolled or unbeaten book is always much better than one imperfectly beaten, for here nothing is demanded but sheer force, and that is always exercised with better results by a machine. As already pointed out, our modern printed books do not require any such work; besides, the so-called surface papers and printed illustrations prohibit both beating and rolling, as such work would destroy the high surface of the paper.
Old books, on the contrary, where the paper is unsized, spongy, and swollen, require some such work, as pressing alone, even for days, has not the required effect.
In beating, the work should be divided into sections or lots of 15 to 20 sheets; they need not be counted, they are measured by the eye. For rolling, however, the sheets must be counted off exactly, from 8 to 12; they are knocked up and placed between zinc plates of same size and passed through the rollers obliquely, the upper back corner being first inserted. It is well to introduce the second lot before the first has quite passed through the rollers; this not only saves the rollers but avoids the extra pressure on the lower corner when a section leaves the rollers. For this reason it is advisable to insert the lots right and left alternately.
The first lot rolled should be examined to test the amount of pressure, and at first a lighter pressure should be applied to avoid risk of injury.
We have now come to the end of the processes through which a book has to pass before it is actually made up into book form. Before we take up this work there is incidental work to be mentioned which comes before the work of binding proper. This is the stitching and treatment of stitched or bound books for binding and the necessary repairs thereto.
The stitched or brochured book is no true book form; it is nothing more than the gathered sheets of a work in a temporary form, handier and more convenient, and therefore more saleable.
To prevent leaves from falling out in the event of their being cut open, they are lightly stitched together--hollaendert.
How did the name originate? It is difficult to say. Perhaps books stitched in this manner were first brought out in Holland.
With this method of sewing, the sheet only gets one short thread in the middle; but as the sewing of each sheet separately would entail a considerable loss of time, that old contrivance of the bookbinder for most kinds of sewing work, the sewing frame, is here made use of. A base or bed has on each front corner a perpendicular screw, upon which is placed a movable cross-bar with a slit. This bar is regulated by two screws; lay cords are fastened to hooks which are slipped through the slits, the other ends being knotted to metal keys fixed under the base.
A narrow movable bar, bevelled to the front of the bed, holds these keys when the lay cords are tightened.
Fig. 16--Sewing frame.
There are no lay cords on the sewing frame for the work of Hollaendering as in other kinds of sewing, but two strips of zinc plate about 1 to 1-1/2 cm. in width are fastened so that at the top they are attached to the hooks and at the bottom are held with a pin. The lot to be sewn is placed rather slant-wise on the bed of the frame to the left, the back turned outwards, the head to the sewer, all sheets, therefore, facing away from the worker.
Fig. 17--Arrangement on the sewing frame.
The left hand takes the upper sheet with thumb and middle finger, so that the forefinger at once falls in the middle of the sheet, turning the sheet so that the head A lies to the left and face upwards as shown in the illustration; zinc strips are stretched at the points x.
The left hand is introduced into the opened sheets from behind to take the needle when pushed in and then to draw it out again; the right hand inserts the needle from outside, and also draws out the needle inserted from inside by the left hand.
All kinds of sewing on the sewing frame are divided between both hands in the same way.
The threaded needle is now introduced into the sheets to the right of the right strip at the back fold and again brought out to the right of the left strip, the sheets being meanwhile held open by the left hand.
The thread is drawn out, except for a short end, the second sheet taken and laid open, and the needle is now introduced to the left of the left strip and brought out to the left of the right strip; and so on, each time introducing the needle from the right side to the right of the strip and from the left side to the left of the strip, drawing out accordingly. The thread is only to be seen on the outside of the strips.
The so-called English darning-needle--a long needle with a long eye--is used by the bookbinder. A special thread is made on purpose, the highest number being used for hollaendering.
When the sewing frame is packed so full that the sheets can no longer be kept properly squared, a sharp knife is taken and the threads cut off along the metal strips, and the sheets are then removed from the sewing frame. Every sheet is now independent of the other, and has a thread in the middle, of which a little may be seen at each needle-hole. These ends are afterwards pasted up in the work to follow. It is clear from this method of sewing that it is not necessary to tie a second thread on to the first when finished, but simply to begin with a new thread, letting the ends always project a little.
This method is the more recent and practical. It admits of one kind of sheet being sewn immediately after folding: nay, more: whilst one folder is still busy folding, another may begin to hollaender. It is not till afterwards that the sheets are gathered. Gathered sheets are sewn in the same way, and are more easily knocked up than when sewn on cords and the threads left uncut after the old style instead of on metal bands. In hollaendert sheets the threads lie as shown in Fig. 18.
Fig. 18--Arrangement of threads in hollaendering.
Fig. 19--Small stapling machine for single sheets.
Lately, in brochuring, the sheets are not hollaendert, but sewn with wire on the machine. This is a very good method when the finest possible staple closing from the outside is used. For this work a small machine is used, similar to those used for wiring documents, copy-books, and single sheets, which have an automatic wire-drawing action.
The batch of sheets is here arranged face upwards to the right of the worker. The right hand takes the sheet by the head, opening it at the same time with the forefinger, and inserts it in the groove of the machine, which is at the same moment set in motion. With each different sheet the position of the staple must be changed so that all do not stand the same height, as it would cause the paper to be cut through in pressing.
The accompanying sketch shows the arrangement of the collected brochures.
Fig. 20--Arrangement of staples in brochures.
It is barbarous to sew more tightly with wire, for in the necessary pulling to pieces to bring them to their former state for binding they are sure to be more or less damaged. Sewing with a large machine using strips of gauze cannot be recommended.
The further treatment of hollaendert or wire-sewn sheets is dealt with towards the end of the chapter.
Most of the books given to the small binder do not come to him fresh from the printer, but sewn, used or unused, cut open, or as published.
The sheets for binding must, as far as possible, be restored to the condition they were in before they were sewn. It is absolutely necessary that they should be made into loose single sheets. This work is called "pulling to pieces." The outer cover is torn off, the thread or wire inside the sheet removed, and the sheets very carefully separated one by one. When they are all pulled to pieces they are pushed open a little at the back, first to one side, then to the other, and scraped with a knife from top to bottom so as to remove all dirt, glue, &c., adhering.
Where the sheets had been cut open and the inner leaves worked out of place, they must be well pushed into the back again. The sheet is lightly held half-open in the left hand, and the leaves are knocked into the back with a long folder or knife.
If sheets are found badly folded they must now be properly re-folded.
Any torn places must be repaired. A special chapter ought really to be devoted to this, for repairing and restoring is an art in itself. Here, only the most necessary work can be mentioned.
There are three different kinds of tears: tears in the print, in the margin, and in the back. The first may be torn with slanting edges; in such a case, both edges must be carefully pasted, fitted to each other, a piece of paper laid over and under, and then well rubbed down. If the tear has not slanting edges, but is clean cut, it is always best to paste the edges likewise and to join the pieces by overlapping very slightly. It always looks better than the patching with strips of paper--a method adopted even by good workmen. The pasting on of pieces of tissue paper is to be condemned.
In cases of repairs like the foregoing, a piece of unpasted tissue paper may be laid on the repaired place and rubbed down, so that any paste exuding cannot do harm, and besides, it will serve to strengthen a weak place. It may be used, however, only on condition that the tint is exactly the same as that of the other paper.
Tears at the margin are repaired by pasting on strips of the same paper or of a kind as near as possible in texture and tint. To make the mend less noticeable, the paper should be torn beforehand, that is to say, by tearing one side of the paper the edge is less sharply defined and appears more like part of the sheet and is hardly perceptible.
Tears in the back (if outside) leaves are mended by pasting them down on to the following inner leaf; afterwards the glue makes this place still stronger. If the middle leaf is likewise torn, a narrow strip is pasted into the back. This may be cut true by the straight-edge if a very narrow strip suffices, but if the tear is here also sideways a piece of torn paper must be pasted on. If there are backs, torn off corners, or the like to be put in, a suitable paper is selected, a piece a little larger than the missing piece cut off the edge of the damaged leaf neatly pasted, the patch laid on slightly overlapping, and well rubbed down under a piece of waste paper.
When thoroughly dry, the loose edges of the patch should be carefully torn off so as to slope and taper off nicely.
When all parts are repaired and the sheets again in proper order, the book is pressed for a while between boards.
It is thus that good books are treated, and although it would be better to return books of no special value as not worth the labour, still it does happen that cheap books--mostly school books and periodicals--have to be repaired. A quick way of getting through such work is as follows:--
A larger piece of similar paper is well pasted and laid upon a clean cutting-board, and from this piece strips of the required width are cut, laid down in their place, and cut to length with the shears, and well rubbed down under waste paper. If the pasted piece becomes dry before it is used it must be coated again.
All repaired sheets must be laid between mill-boards to dry.
Worn and damaged periodicals are repaired in the same way. Generally the numbers are curled towards the fore-edge. Before commencing to pull to pieces they should be rolled towards the back, especially close to the back, to straighten them. The leaves must all be well pushed into the back, turned down corners (so-called dogs' ears) must be turned up, and two-page illustrations must be pasted away from the back. There are generally single or double leaves at the end of each copy or sheet--these must be pasted on.
This work is not done singly, but the whole volume is at once laid open from back to front for pasting. All parts of the sheets to be pasted are placed at the front edge of the table, the edges fanned out, the other sheets wherein they are to be placed being meanwhile pushed further back so that they are not touched during pasting. The fanned-out sheets are pasted and each is rubbed down on to the sheet following.
It has already been said that in pulling to pieces the wire or thread sewing must be removed; this is not always easy. To begin with, the wires must be first bent upwards; if they are firmly glued to the outside of the back, the latter has first to be softened by smearing it very thickly with paste, and after leaving it some little time the glue may be scraped off and the wires loosened. Not until then can the wires inside the sheets be removed and the sheets separated. The backs of books that have been bound are softened in the same way.
Even to-day--Heaven help us!--well-got-up books, even illustrated works, are sewn through sideways with coarse wire staples. Great care must be used in removing these and in separating the sheets, so that the bookbinder may at least try to undo the harm caused by barbarous methods practised either in thoughtlessness or ignorance.
It sometimes happens that the back of a book is so bad that it is necessary to cut it clean off. The leaves are then made up into sections of 6 to 8, levelled at the back, and overcast with a fine needle and fine thread. This work can be done quicker with an ordinary sewing-machine, adjusting it for the longest stitch.
New works consisting of thin single sheets are done in the same way.
CHAPTER II.
SEWING.
Modern books are fastened together by sewing; as a rule thread is used, and always in sewing good books. Thread sewing is very much better than wire stitching. In the first place, thread has not the disadvantage of rusting, to which wire is always subject; secondly, thread does not break the paper in the back, as so frequently happens when cheap paper containing much wood fibre is wire-stitched. The greatest advantage of thread sewing over wire lies in the flexibility of the spun thread; with sharp pressure it lies flat in the sheet, whilst wire does not give at all. Besides, it is flexible the whole length, and this adds greatly to the life of the book.
All thread sewing is now done by machinery and is really satisfactory.
Only the very smallest job shops sew their books by hand.
The principle of sewing is to fasten each sheet to several cords or bands by means of a long thread running right along the inside of the sheet. These cords give the book its hold to the cover; therefore the more cords used, the more firmly is the book secured to its cover. There are now two methods of fastening the sheets on the cords; first, there is the older method of passing the thread along and out of the sheet, around the cord, and again into the sheet, and repeating the same movement at the next band.
Fig. 21--Arrangement of threads in old style of sewing.
Nowadays, this method is almost entirely discarded. When for special reasons, or on account of its greater strength, it is desired to imitate the old method, the sewing is done on double cords; that is to say, for every cord two cords are stretched alongside each other and regarded as one. This sewing is more tedious, as the thread must take up each cord as shown in Fig. 22.
Fig. 22--Arrangement of threads with double cords.
These somewhat elaborate modes of sewing have been simplified in recent years by making saw-cuts in the back, in which the cords are laid. By this means the sewing thread never actually passes out of the sheet, but is drawn behind the cord lying in the saw-cut and thus holds it.
That is why we "saw-in" our books. The sawing-in is done with a broad saw; the so-called "tenon saw" being the one most generally used. The saw-cut must correspond exactly to the thickness of the cord to be used, should be less deep than wide, and should not take up too much glue when glueing up, as this might easily turn brittle. By inclining the saw to right and left alternately during sawing, the resulting cut will be something like this -----/__\-----; this is the best and most usual form.
The common practice of widening the cut by means of a coarse file gives a triangular cut like this -----\/----- which is objectionable, as the groove gets filled with glue, thus rendering the thread liable to break. As many cuts must be made in the book as there are cords to be used, besides the so-called kettle stitch at head and tail by which the thread is passed from one sheet to the other.
Dividing the back for sawing-in is done by marking off 1 cm. from the head and twice as much from the tail and dividing the rest into equal portions with the dividers. An octavo should never be sewn on less than four cords, and a folio on six. If obliged to use less through low prices, then three must be taken as the minimum number, and that only in exceptional cases. If the books are very small--as, for instance, prayer-books and hymn-books less than 7 cm. in height--it may then be permissible to sew on two cords.
The division for the different sizes for sawing-in is made as shown in Fig. 23.
Fig. 23--Divisions for sawing-in.
The saw-cuts at the kettle stitch are less deep and quite narrow; they only mark the place where the thread is to pass in and out.
It may be wondered why the distances between the cords, when using four or six, are unequal; the reason for this will be explained when we come to the sewing of such sizes.
In sawing-in, the batch to be sawn is knocked up head and back and put between two boards--if the volumes are thin, several may be laid together--so that the back projects about 1/2 cm. beyond the edges of the boards. The first and last sheet of each volume have previously been laid aside, as these, with one exception, are not sawn-in.
Books and boards are now clamped in a small hand-press, which is screwed up by hand only. For convenience of working, the press with the screws is laid flat upon the table, so that the nuts are against the table edge. The press is propped up at the back by the press-jack. The divisions for the cords are marked on the back with a lead pencil after measuring with the dividers, and the cuts made according to the markings. If several volumes of the same size are to be sawn-in, the top sheet of the first batch sawn is used as a guide for marking the others, thus saving the work of measuring each one with the dividers. Where much sawing-in is done, a sawing-in machine is employed.
The sheets are placed, backs downwards, in a moveable box, which is led over a system of circular saws.
Fig. 24--Machine for sawing-in.
After the work of sawing-in, the first and last sheets are replaced, the volumes again collated, and the end papers put in place; the sheets are now ready for sewing.
End papers are the blank leaves which the binder places at the beginning and end of a book. They vary according to the style of the book. Every end paper consists of a "fly leaf" (this lies over the title page in the book), the "paste-down," and in most cases of a "tear-off." For the stronger end papers and in half-leather bindings a cloth joint is used.
Whilst dealing with these end papers, we must not forget the narrow guard; it is worked on the prepared end paper (as will be shown later) by folding over, and serves to enclose the title or end page with which it is sewn. The words joint, guard, and swell may here be more clearly explained, as they are used very frequently in the bindery.
In the first place, we call the part where back and cover are joined by a sort of hinge "the joint," also strips of leather, cloth, &c., used for making this part are called "joints"; secondly, the slightly raised part of the back, caused by pressing or sewing, is shortly called "the swell"; and any strips of linen or paper fastened into the back of the book for hingeing maps, plates, &c., are called "guards."
For use as end papers, a paper must be selected which suits in quality and tone the printed paper. Nothing shows lack of taste more than the use of a blue end paper with a paper of yellow tone. For both back and front a double sheet is necessary and is cut the required size. A paper guard, about the width of three fingers, is made from a piece of stout waste paper and pasted on a narrow margin at the back of the double leaf, in order to protect it in the joint and also for fastening on the cover. If there are single leaves to be used up, two of these might be pasted to each other narrowly on the back and upon this the guard; this is the so-called double end paper.
If instead of these only a single leaf is taken, then we have a single end paper; this is used for cheap school books and generally at the back only.
The accompanying sketch shows both these end papers with the small guard already folded. This folding of the guard is not very easy for the beginner. The leaf is placed face upwards, square in front of the worker, and a very narrow margin at the back edge bent upwards about 3 mm. in width, the forefinger and thumb of both hands shaping and bending the guard, working from the centre to the ends.
Fig. 25--Suggestions for single and double end papers.
Should the sheet from which the end papers are made be a little wider than required for the end papers, the tear-off may be folded at the same time; with double end papers, the leaf which is to be pasted down later is inserted between fly leaf and tear-off, and therefore is called "insertion."
Fig. 26--Suggestion for double end paper with tear-off.
If the end papers are to have a cloth joint it must be placed within the two leaves or, better, pasted in face inwards. Double cloth joints are no longer used in printed books, as they make the end papers too thick, and in the subsequent rounding the first sheet is apt to break. The joint is here also folded on as before.
Formerly, when linen joints were used, the end paper was simply made by inserting the strip of cloth and hingeing on the outside leaf about 1 cm. from the fold. This, however, has many disadvantages, therefore the end papers are made as explained, then carefully tearing off the outside leaf in the back in pasting down and cutting it as required it is pasted on to the board, as will be more fully explained under "pasting down."
The French paste a double leaf before the first and last sheets after having pasted a covering leaf around these.
For extra work, the following style of end paper is the best; it is used in England for all high-class work, and in Germany also it has been adopted by all the first-class firms.
The end papers consist merely of single leaves the size of the sheet.
These are fanned out at the back to make a small margin and pasted. The first leaf is then pasted down on the end-paper sheet so as to leave a margin of about 2 mm.; the second leaf is pasted level with the back.
All end papers are proceeded with in the same way.
If these are to have a cloth joint it must be pasted on the outside also only 2 mm. wide. When the end papers are dry, they must be stitched down along the back, 2 mm. from the edge, with the sewing-machine adjusted to its longest stitch. It is unnecessary to knot the ends of the thread--they are cut clean off. When there is no sewing-machine, the volumes must be overcast by hand. This overcasting is done by inserting a fine needle near the back of the knocked-up sheets from above and drawing the thread almost quite through, the second and following stitches all being made from above. The thread would then appear as in Fig. 27.
Fig. 27--Overcast end paper.
These end papers are made up before sawing-in and sawn in with the book, and when it is not possible to stitch them with the machine they must be sawn in before overcasting, or the sawing would cut the threads.
Now for the sewing. We stretch the requisite number of cords, which are secured to the hooks at the top by a simple loop which is easily undone as soon as it is taken off the hook. At the bottom a double loop is made, through which a key is passed so as to hold the stretched cord underneath the moveable board.
Fig. 28--Loops for attaching to frame hooks.
Fig. 29--Loops for taking frame keys.
The length of the cords is regulated by the thickness of each book, and as it is possible to sew a number of books at the same time when they are all sewn the same way, the length of the cords is regulated accordingly; it also depends upon the kind of books to be sewn. Cheap books get 3 cm. for every cord on each side more than the thickness of the book, that is 6 cm. plus the thickness of the book. School books get still shorter cords. For extra work, where the ends of the cords are laced through the boards, one should allow double. It is easy to calculate the length required for a single volume, but rather difficult for a batch of books varying in thickness; it is then better to measure.
For example, suppose we have to sew a batch of six books, all differing in thickness but measuring in all 25 cm. high; we would allow for cheap work: 6 vols., each taking 6 cm. extra lengths = 36 cm. + total height, 25 cm., making 61 cm.; for extra work: 6 vols., each taking 12 cm. extra lengths = 72 cm. + 25 total height = 97 cm. length of cord.
The collated batch of books is laid on the bed of the sewing frame as in hollaendering (Fig. 17), the sheets taken hold of in the same way, and laid open for sewing. Of course the cords are adjusted to the saw-cuts, and it is better to push them more to the right than to the left, so as to give the left arm full play. Here also, as in hollaendering, the left hand does the work behind the cords inside the sheet, whilst the right inserts the needle from the front and again brings it out.
Fig. 30--Suggestion for sewing on four cords.
Fig. 31--Suggestion for sewing on six cords.
The first and last sheets--called end sheets--are sewn a little differently from the others, as the needle is here not inserted and drawn out exactly at the cord but at a little distance from it so as to allow them to be adjusted afterwards. Sewing[1] with us is invariably begun with the last sheet at the right, working on to the left, and reversing the process with the following sheet, and so to the end, so that the thread one way passes from and the other to the worker.
With all other sheets, excepting the end sections, the thread is inserted at the kettle stitch and brought out at the next cord, round the cord, and inserted at the same hole, to be brought out again at the next cord, and so on till the thread comes out at the other kettle stitch and is inserted in the next sheet to go through the same process.
With books sewn on four cords, it is allowable to skip one of the two middle cords alternately, so that each time the thread passes on to the right the right middle cord is skipped, and the left is skipped when the thread passes in the opposite direction. This facilitates and shortens the work without taking away from durability or quality. Books on 6 cords may be treated in the same way; the right and left of each pair of cords may be skipped alternately.
It was for this reason that we paid attention to the distribution of the cords on the back when sawing-in (see Fig. 23).
Footnote 1: In England, France, and part of Holland, sewing is begun with the title page.
This method of sewing is known as "end to end," in contradistinction to "two sheets on." The former is the better method and is essential for valuable books, unless the sections are exceptionally thin. The latter is "good enough" (i.e., not worth much) for the trade and cheap work.
As far as strength is concerned it would do, but a book sewn in this way does not swell sufficiently in the back to make a proper backing groove.
It is an old rule in bookbinding that each sheet after it has been sewn should be pressed down with the needle so that the backs of the sheets lie close and firm together; this is called "pressing down." Should this, however, not be sufficient, the back must be knocked firm from time to time with the dividers or a rule.
The first and last sheets must be fastened to the one following and preceding respectively; but in the course of the sewing this enchaining to the preceding sheets--the so-called kettle stitch--is only necessary in the case of very thick sections. It is done by passing the needle through and bringing it out between the two preceding sheets at each end and thus chaining on the then top sheet to the one lying underneath.
The two-sheets-on sewing is done by laying open the second sheet on top of the first after making the first stitch in the first sheet and then passing the needle through the second sheet, then the third stitch is made in the first sheet and the fourth in the second sheet. One length of thread is used for the two sheets. Where the sheets have not been cut open, the left hand lightly takes the sheets in turn where they have been cut, a folder is placed in the middle and is shifted from one to the other as required. The process is the same whether there are only three cords or even six.
Fig. 32--Suggestion for sewing two-sheets-on.
It has already been said that several volumes of the same kind can be sewn on top of each other on the sewing frame; in this case the volumes must be separated from each other after the sewing is completed.
The free ends of the cords are untwisted so that they may be scraped open more easily afterwards, and then one volume after another is drawn along the cords to the ends until they are twice the length of the free cords away from each other, which, of course, will vary according to the subsequent style of binding.
So then we allow 6 and 12 cm. according to circumstances; but this length is curtailed to 3 cm. in the cheap school books, because the shorter the cords the quicker they are scraped open. Every cord is cut in the middle between the books with the shears, thus separating each volume from the other. The strands of the loose ends of the cords are now completely untwisted by inserting the cord in the groove of the scraper and repeatedly rubbing it up or down with the back of a knife.
After scraping the cords, the end-paper guards are always pasted down; the book is laid with the back to the front edge of the table, the first sheet with the end paper is turned downwards, the end-paper guard is bent up a little so that it stands away from the sheet, paste it neatly and carefully, close the section and adjust it so that the sheet in the end paper is level with the others, but not the end paper itself--this must project a little at the back. When only one finger is required for pasting it must be the middle finger, so that the forefinger is free from paste and ready to take hold of anything.
If stitched end papers are used for extra work, a sheet of paper is laid on the second sheet so as to leave 3 mm. free, paste this strip and bring down upon it the once-more closed first sheet, taking care to square it at the outside with the body of the book.
The folder should be brought down firmly over the outer sheets after pasting down so as to ensure the paste sticking.
If the pasting-on of the joints is not properly carried out, the result will be that in most cases the book opens badly when finished.
In half-cloth or other simple bindings, the scraped cords may be pasted on at once. Bring a little paste (about the size of a pea) upon the point of a folder under the slightly raised cord, pasting the latter evenly and neatly upon the paste-down of the end paper so that the pasted-down strands of the cord lie like a feather. To prevent the pasted cords sticking to each other, the books are piled up back and front until dry. In extra work, the cords--which are also longer--must by no means be pasted on; a piece of waste paper or a cover the size of the sheet is pasted outside the sections under the cords, level with the backs.
This serves partly as a protection for the end papers and partly to make a good joint when covering.
The volumes so prepared are now glued up. They must be knocked up at head and back; they are then placed with the backs outwards on a board specially kept for this work--the glueing board--with the fore-edge of which they must be exactly level. On top must be placed a smaller board or a heavy piece of iron, likewise level with the book.
The book backs are thus held firmly between the glueing boards, the left hand holding them firmly by pressing on the top, the right hand glueing the backs with very hot but not thick glue; rub this well in with the point of a hammer, and after having firmly squeezed the glue out of the brush, use it for taking off the surplus glue from the backs. An old trick of the bookbinder is to heat the hammer for this work. It is a bad plan to give the back a thick coating of glue and then allow it to dry, because it at once becomes brittle.
Some experienced workers place the books between the glueing boards so as to leave about 1 cm. projecting, as it is thought that the glue thereby gets better between the sheets; but this method is out of date and is of no special value. It is, however, of great importance that the glued book should be laid so that it is truly square at the head as well as the back, for if this is neglected no amount of trouble will save the book from being cut out of shape.
Before passing on to the next chapter we have still to mention the mechanical contrivances for sewing. For small as well as large binderies, machines have been invented both for wire stitching and thread sewing; the former are more generally used, the latter not being sufficiently perfect in construction to meet all demands for speed and accuracy. Then also the method of fastening the book in the cover differs so much from the traditional method that we must still hope for improvement.
When this comes to pass, this machine will then supersede the wire-stitching machine, with all its unavoidable disadvantages. The working of the machines is so simple that they are attended to almost entirely by girls. We refrain from giving descriptions of mechanical appliances within the limits of a short treatise, as any day may bring forth new inventions which are certain to effect great changes in this department.
Besides these costly appliances there are also simpler sewing-machines for small shops, by which books are sewn in very simple fashion over steel needles, by means of which the cords may afterwards be drawn along.
Fig. 33--Thread-sewing machine.
Fig. 34--Wire-sewing machine.
As these machines demand very large saw-cuts, they can only be used for trade work and any cheap lines. We only mention them to draw attention to their existence. Unprinted paper and music are sewn on tapes as well as cords. This method of sewing is described in Chapter IX.
CHAPTER III.
CUTTING, ROUNDING, BACKING.
Fig. 35--Rotary guillotine.
In nearly all cases the book is trimmed after glueing, and it is best to do this before the glue is quite set. Even in extra work books are nowadays trimmed on three sides, that is, before the book is rounded each side is cut one after the other. This method has the advantage that it is quicker, that the top and bottom corners of the round fore-edge cannot break, and that it is easy to treat every side during the process of marbling.
Of course, in the best work the book is first cut at the front, rounded, pressed, and then cut top and bottom.
Under present conditions we might completely abandon the old method of trimming with the plough, for, although this is a most valuable tool, it would not pay to use it now, and the shops where it is still in use are few and far between; besides, our German machines now do the work so thoroughly and accurately that we are able to execute the highest class of work by their aid.
Fig. 36--Lever guillotine.
The machines worked by a lever are very suitable for small shops and small books. Rotary action is for heavier work and is more suitable where both heavy and light work have to be done.
The fore-edge is generally trimmed first; the back of the book is carefully adjusted to the "back gauge," the back gauge is so adjusted by moving backwards and forwards that the knife comes exactly upon the point marked beforehand. The first principle to be observed in trimming is that as little as ever possible should be taken off the book.
Measuring and marking for trimming are done with the dividers; the latter is called "marking for cutting." When the back gauge has been adjusted so that the points lie directly under the knife, the clamp which holds the book in position is screwed down and the machine set in motion. The book must be cut smooth and quite free from any jaggedness, and if this has not been accomplished the knife must be ground or, at least, well sharpened.
Something must be done in trimming top and bottom to prevent the groove at the back from receiving too much pressure. The simplest means is to glue a thick board on the under side of the clamp. If a piece of stout cloth has been pasted to this board, it will afterwards be easily removed from the clamp if it is lightly glued on at two places only. If cloth is not used, pieces of the board will adhere to the clamp and cause no little inconvenience.
Instead of this, there are metal plates sold which are fastened to the clamp in a simple way, either by screws or springs, and they are just as simply removed.
The bottom edge has to be cut first, as one is thus able to adjust the head--which, of course, must be rectangular--against the back gauge and then to make the bottom edge parallel. After cutting this edge, the book is turned round and the bottom edge adjusted on the back gauge so as to get the top edge ready for cutting. Whilst doing this, care must always be taken that the book is placed under the clamp so that the arrangement made for saving the groove from pressure is effective.
Fig. 37--Top edge arranged for trimming when trimming three edges.
As our machines are made to cut from left to right, the book back must be on the left.
Very often a book contains so many folded plates that it is considerably thinner in some places than at others. These thin places must be properly packed with paper or strips of board, otherwise the knife is sure to tear or jag, no matter how sharp it may be. This packing may be left in the book until the book is quite finished and then taken out.
If any fibrous matter has stuck to the bottom sheets through cutting on a much-used bed, it must be removed with a very sharp knife.
The trimmed volumes are "rounded," i.e., they are rounded and the groove made at the back to which the boards have to be fitted. For this reason the grooves must be made to suit the thickness of the boards to be used.
Fig. 38--Rounding the book.
To round a book, slightly damp its glued back, place it on a firm stone or metal bed, and knock it round with a hammer. Properly speaking the process is as follows: The left hand takes hold of the back of the book lying flat before the worker and works it into a round form, the right hand helping all the time by beating it along the back from one end to the other.
In this way each side is treated alternately until the back is evenly rounded. The rounding of the fore-edge should be equal to one-third of a circle.
Books that have been hammered so much that they fall straight from the centre towards both sides are called "over rounded"; if, on the contrary, the book is round at the sides and almost straight in the middle the book is called "flat rounded." The latter occurs when the thread used in sewing has been too thin or held down too much (see page 37). Great care must be taken to avoid what is called springing a section--this is generally caused by a break in the glued back; but it is almost impossible to round a book perfectly if the sections are very thick or if it contains many pasted-in plates.
There are now very useful machines for rounding books, also hand machines. The work connected with these consists simply in turning the book a few times, pushing the back up to the rollers each time.
Fig. 39--Rounding machine.
When the book is properly rounded, it is "backed," that is, it is so placed between backing boards that they are away from the back just as much as is required for the groove, the width of the latter depending upon the thickness of the boards; a small thin volume gets thin boards and therefore a small groove; a thicker volume requires thick boards, and, of course, a deeper groove. The made groove should be a little deeper than the board set in it.
The book and backing boards are placed in a wooden press, screwing up by hand and once more carefully adjusting. To do this, the press is first placed lengthwise on the table so that one end projects a little over the front edge of the table; the evenness of the rounding is then perfected--one hand at the back and the other at the front edge pushing and adjusting. The better and truer the book has been rounded before laying in the boards the less there will be to do when placed in the press.
If the rounding is correct, the head and tail must be examined to see that they are exactly rectangular, for the book may have been knocked untrue, and the evenness of the grooves--which are easily disturbed--is also examined.
Backing and rounding is the most important work as far as regards the appearance of the book when finished; it must be done with the greatest exactitude and requires much practice. Although it is hardly perceptible, yet the great difficulty lies in the book itself being so very easily shifted.
When the book is placed in the press without a fault it is screwed up as tightly as possible with the screw key, and through this the grooves already project over the edges of the backing boards; but a sharp groove can only be obtained by the help of the hammer.
The hammer, however, must not be used blindly on the back, but by lightly knocking, blow by blow, the first and last 4-6 sheets must be brought over the edges of the boards. This done, the whole of the back is well pasted, and after remaining thus a short time it is then rubbed with the point of the hammer along the sheets until all superfluous glue is soaked and scraped off. With a handful of paper cuttings the back is rubbed smooth and clean. The use of a toothed cachir iron is strictly forbidden, but the round side of this tool may be used instead of the hammer.
Fig. 40--Backing machine for small shops.
For backing, we have also a useful machine--the backing machine. For small shops it is made for clamping only, and the making of the groove is done with the ordinary hammer. For large shops this machine has a roller going right across the back which forms the groove down each side.
Fig. 41--Backing machine for large shops.
Valuable books are either trimmed at the front and at once backed or they may be backed before trimming. This is generally done with bulky books, as they are liable to throw out a section, and this danger is lessened by backing first. The work of backing remains the same. If the fore-edge has already been trimmed, care must be taken that the grooves do not suffer during trimming after backing. One way of effecting this is to lay the book on a special cutting board with the edge up to the groove, or by making use of the arrangement on the clamp already described, and adjusting the groove of the book to the blocks fixed on the clamp.
Should the fore-edge not have been cut, the book must again be knocked straight after backing; to do this a strong cord is tied round the book about 1-1/2 cm. from the back, the book is then laid upon a firm bed, and the back again knocked straight; this work is called "tying up."
Fig. 42--Backed book arranged for trimming.
It facilitates the work if the book is taken up and lightly held in the left hand whilst the right holds the hammer and knocks the round inwards until the book is once more square.
The squared book is now trimmed, and it is not until the trimming is finished that the cord is loosened.
In pressing, several volumes of the same size can be done in the hand press at one and the same time.
CHAPTER IV.
MARBLING, GILDING, &C., THE EDGES AND HEADBANDING.
The edges of a book are nearly always finished off in some way or another, as the plain white edges would quickly become soiled. As a matter of fact, the binder always uses a covering of gold or colour for this purpose, and care should be taken that this way of treating the edges is decorative and not the reverse.
In small binderies the edge is most usually sprinkled. A small brush with a handle (such as is used for blacking shoes) is dipped into a very thin coloured liquid and rubbed over a fine sieve which is fixed in a frame. The sieve is kept at sufficient distance from the edges of the book to allow the little drops of colour to fall like a fine rain. For this work the book is screwed up in the press (which is laid flat) by means of the press-jack.
As a sprinkling colour, nut-wood stain thinned with water is used, or indigo, carmine, Prussian blue, mahogany brown, green cinnabar, all well diluted with water, with the addition of a little paste and borax or a few drops of dilute carbolic to prevent the paste turning sour; aniline dyes have a common appearance. The sprinkle must fall very finely upon the edges, therefore the first large drops should be taken out of the brush by giving it a few preliminary rubs over the sieve.
A few variations are made in sprinkled edges by scattering damp sawdust, sand, or bran on the edges before sprinkling, thus producing a coarser kind of sprinkling. Similarly rice, barley, even starch or drops of wax are used. All these edges are out of date and in really good workshops are every day falling more and more into disuse, preference being given to marbling upon a sized ground.
For the production of even marbling an edge-marbling roller has recently been brought out.
Rubber rollers--one or two--together with the automatic colouring rollers bearing aniline dyes mixed with glycerine, are made up into a handy contrivance by means of which smooth coloured edges can be rolled over. These edges are passable only when carefully and skilfully executed; as a rule they look coarse and common and are taken up only by badly equipped shops. Marbling rollers can be used for comb marbling as well as for small veined marbling.
We may say that the coloured edge is the oldest style.
Earth colours which cover well--cinnabar[2] (red or green), carmine, chrome yellow, graphite, bismuth, and also other colours that cover well, indigo, carmine, and Prussian blue--are ground to a fine powder and thoroughly mixed with water and a little paste or gelatine so that the edges may be evenly covered.
Footnote 2: Cinnabar if not red must be a preparation with other colour.--Trans.
Only printed books are put in the press, and in this case they must first be rubbed down with alum water. After about five minutes the colour may be laid on. Hog's-hair brushes are used for this. Recently, eosin has been used to colour red and picric acid for yellow, both well diluted with water.
The paste edge is a variety of the coloured edge; it is produced by loading paste with a very strong colour so that it covers well when laid on. With the blunt point of a stick, a bluntly pointed cork, or even the finger-tip, figures may be traced in the colour when laid on, and then the figures may be brought out better by going over the lines with a pointed stick. The work demands a skilled draughtsman if a good effect or something more than the very simplest design is desired.
The book must be pressed for pasting the edges, and the paste colour must not be laid on too thickly or it will spring off when dry.
Coloured as well as paste edges will take gold tooling and afford considerable scope to the skilful and thoughtful workman.
The finest way of finishing edges and the one allowing greatest variety of treatment is known as marbling; this is a special process.
Formerly regarded as a secret art, it is now an easily acquired branch of our work, thanks to the careful experiments and excellent demonstrations of the master bookbinder, Herr Joseph Halfer, of Buda Pesth.
The whole process of marbling depends upon the peculiarity possessed by colours of floating upon a sized surface when they are mixed with oxgall, and a colour containing more gall forcing off the one first applied. Besides, the colours may be drawn about with a pencil or stick without their mixing. If the smooth edges of a book are brought into contact with such a floating surface-colour they will take up the colours completely.
Ground and colour must each have certain fixed degrees of consistency, and the atmosphere both in and out of doors has also a great influence upon the work.
The prepared body, shortly known as "the body," is at present always composed of boiled Carrageen moss. To every litre[3] of water exactly 12 g. are added and the liquid is put in a saucepan, which is never used for any other purpose, and placed on the fire, great care being taken to catch it just at boiling point or it will all boil over. At the right moment take the saucepan from the fire and strain the contents through a hair sieve, what remains being thrown away as useless. The body may be used the next day, but for figured edges it is better after having been kept three days, and for veined marbling five days.
The vessel containing the body must be kept covered so as to exclude all dust.
Footnote 3: Not quite a quart.
Gum tragacanth (known as "gum dragon") can also be used as a body, but Halfer's colours are not intended to be used with this.
A marbling trough to contain the body is used whilst working; it is made of zinc plate, is about 15 cm. in width, 50 cm. in length, and 3 cm. in depth, and has a sloping partition soldered near one end, and the colour not taken up is drawn into the division thus made.
Illustration: Marbling Trough
A bowl, about 6 cm. across the top, is kept for each colour, and also a hog's-hair brush and a birch-twig brush.
A small bundle of birch twigs is tied round with thread, leaving about 4 cm. of the twigs free, the thickness of the lowest part tied not exceeding 1 cm. The bristles of the brush are tied back so as to form loops and held awhile in boiling water so that they retain their shape after drying and untying. With a brush made up in this way, drops may be laid on anywhere.
For all drawn-out edges only bristle brushes are used, whilst for all other edges a brush is used only for laying on the first colour. For some edges a wide brush is used, so that the whole trough can be filled at one blow; a carpet brush with a short handle is most convenient to use.
A little stick for tracing the colours is also necessary--a butcher's skewer is as good as anything. Besides this, the colours are drawn by combs of various widths; these are easily made by glueing pins with their heads at fixed distances between two strips of mill-board: the result is a tool resembling a comb. All requisites can be conveniently kept in a little wooden box together with the colours. Nowadays only Halfer's ready-made colours are used.
Fig. 43--Marbling outfit.
Any one wishing to learn the process of marbling edges would be wise not to attempt all the styles at once, but should be content to learn one before proceeding to another. We will commence with "comb" marbling, also known as "feather" marbling.
When marbling is to be done, the colours must always be tested first. A little colour is shaken into each bowl and its brush placed with it, and one or two drops of prepared oxgall added to each colour so as to make the colour float on the surface.
One prepares one's own oxgall. An ox gall in the gallbladder is procured from a butcher, a glass funnel is placed in a bottle which has been weighed beforehand, and the bottom of the gall bladder is pierced so that the bladder empties its contents into the bottle. After finding the weight of the gall, add to the weight of the gall alone one-sixth and pour into it spirit of wine until the weight is equalized; shake thoroughly and strain the mixture, which will now be quite clear and ready for use.
The colours, with their brushes, are placed in the order in which they are to be used, beginning with the darkest and finishing with the lightest.
A drop of colour is let fall from the black brush upon the body, the surface of which had previously been drawn off with a strip of paper; the surface of this drop must be about the size of a crown piece.
If part of the colour sinks to the bottom, the body is too thin or the colour too thick, or the drop was too large and could not spread quickly enough; in the latter case the surplus colour will be seen lying at the bottom and will have no connection whatever with the colour on the surface; but if a cloudy connection can be traced from the surface to the bottom then the body has already become sour and in most cases unfit for use. If the colour does not retain its smooth outlines and becomes jagged, it also shows that the body is too old.
If, however, the drop extends as desired and shows none of the faults above mentioned, a drop of blue colour is let fall in the centre of the first, which drives out the first drop in the form of a ring; when it has not this effect, but strongly contracts again, a drop of gall must be added, the colours wiped off to the sloping partition, and the whole process repeated. If the action of the colour was too strong, a little undiluted colour must be added. If the result is satisfactory, a drop of red is added to the blue.
The colour scheme is seen in the accompanying drawing. Lastly, yellow is dropped into red, and black is thereby reduced to a very thin ring.
Illustration: s--black; b--blue; r--red; yellow in centre.
Before each new sprinkling, the old layer of colour must be wiped off.
To do this, cut strips of stout waste paper about two fingers in width and a little longer than the trough is wide. The edge of the strip is placed slantingly at the end of the tank in the surface of the body and the surface colour drawn off, at the same time lightly pressing the ends of the strip against the sides of the trough.
When the colours are satisfactory, the little stick is traced in and out amongst them. If too much colour follows the stick, the body is too thick; only a narrow line of colour must follow the stick.
If the colours are thus correctly prepared, the whole trough is sprinkled in the following manner: Along the middle of the trough the darkest colour is sprinkled in what we might call links, that is, each drop is linked to the one preceding.
Fig. 44--Suggestion for sprinkling colour.
The second colour is sprinkled on in the same way; one circle, however, is on the right and the other on the left of the centre colour. Into each drop of the second colour let a drop of the third and then of the fourth colour fall.
Illustration: Colour trace form.
The colours must then be traced crosswise with the stick in this form and then likewise with the comb. Neither stick nor comb should be dipped more than about 2 mm. below the surface, otherwise the body is set in motion and the colours disarranged.
The combs should not be made too fine, 30 to 35 teeth for every 10 cm. is the best width and sufficient for most cases. If the comb is drawn back again from the other end it produces drawn-back marbling; this is rarely applied.
The finished comb marbling can be still further varied if figures are traced in it with the stick as shown in Fig. 46.
Fig. 45--Comb marbling.
Fig. 46--Suggestion for curl marbling.
Illustration: Double comb colour form.
If a double comb is made--one that allows two combs to pass each other, their teeth being 2 cm. apart--bouquet or peacock and eye marbling can be produced. The double comb is drawn over the length of the trough, at the same time moving the two combs up and down evenly. This motion causes the colours to assume the form shown in the accompanying illustration.
Bouquet or peacock marbling is produced by drawing the double comb through the finished comb marble design, and if the double comb is used immediately after the cross tracing with the stick, eye marbling is the result.
With a little thought it would be easy to invent other fancy designs, but these are better applied to paper, as trimmed edges are more beautiful and effective when the marbling is of simpler design.
Fig. 47--Bouquet or peacock marbling.
Fig. 48--Eye marbling.
Large marble, called also Turkish marble, is produced as follows, using the same arrangement of colours. Only the first colour is laid on ringwise; all other colours are scattered in smaller drops from brushes.
A darker colour is chosen for the last--brown, blue, olive, grey--to which is added a few more drops of gall and as much spirit of soap (spiritus saponatus), as sold by the druggists. This last colour is prepared in a larger and shallow basin. The largest brush is taken with the hand and dipped, shaken out a little, and then lightly knocked on the left hand so as to sprinkle the colour.
The drops will fall in a dense shower, and, owing to their extra impetus, will drive together the preceding ones, and yet they will form the principal colour in the design. If it is desired to have veins of white in the design, a few drops of gall should be added to a little water in a bowl and used as any other colour; the same applies when using white in comb marbling.
In a similar manner the so-called Kremser style of marbling is produced, but fewer colours are then used, generally only black and red, red and blue, brown and blue, green and red, at the end sprinkling a little of the strong principal colour to which, besides the spirit of soap, a drop of pure stone oil--not petroleum--from the chemist has been added. As last colour, blue grey (black with a little blue), brown, or grey is used.
Recently, a sort of paper termed Trichinal marble has been very prominent on the market. Black and light brown or red and light brown or black, red, and light brown, or white, are all sprinkled on with a brush, length (not cross) wise drawn through, and then grey with a few drops of turpentine (but very driving) is sprinkled on with a small brush. The single drops have ragged edges and produce a peculiar effect.
Thin-veined or French marbling is done upon the same ground, though it can also be done on a somewhat thinner body. The colours, however, are diluted by 50% water, and, consequently, more gall is added. As a rule, only two colours are used; blue, red; brown, blue; brown, green; black, red; black, blue. The first colour is laid on in rings with a brush and must be strong enough to spread over two-thirds the width of the trough; the second colour is sprinkled over with a little birch broom in drops that spread out to the size of a half-crown. Lastly, the so-called sprinkling-water is sprinkled over with one dash from the large brush as already explained.
Sprinkling-water consists of two parts water and one part spirit of soap. The small veins must be driven quite close together and the eyes made by the sprinkling-water must not be larger than a small pea.
It should be observed that for this kind of marbling only the darker shade of red is to be taken, as the light carmine lake colour sinks and does not give a fine effect. India red is best of all.
The sprinkled colours are first tested with strips of paper; cuttings of clean note-paper are saved for this purpose. The edges of a book can be marbled only when the book is level or straight, therefore they must be marbled either before rounding or the book already rounded must be levelled by knocking it on a stone or metal slab. In all cases the marbling is done--both with papers and books--by dipping from one corner to the other diagonally opposite, but never deeper than just sufficient to take off the layer of colour.
To prevent the colour from getting between the leaves, the edges are held between zinc plates, which must be dried each time after using. To make the paper or edges take the colours more readily and to prevent any subsequent running off, the edges are lightly washed down with alum water. This wash is made by boiling 100 g. of alum in 1/2 litre of water and using it solely for this work.
The alum solution is laid on with a sponge, with which the edges are washed over. The moisture must have thoroughly soaked in, therefore it is necessary to do it 10 minutes before marbling.
If, however, the edges have become thoroughly dry they will take the colours badly. This occurs in from 20 to 30 minutes, according to the temperature. Marbling can only be done in a warm room where the temperature is equable and where there is no dust.
The marbling bath must be of the same temperature as the room. The body must be skimmed each time before sprinkling the colours, but the colours must be sprinkled on immediately afterwards.
An excellent treatise on the work of marbling edges has appeared under the title: [4]Fortschritte der Marmorirkunst. Von Joseph Halfer.
William Leo, Stuttgart.
Footnote 4: The Development of the Art of Marbling.
Illustration: Pressing Board Profile
Gilding edges takes up most time when only occasional books are to be done. The fore-edge can be treated either flat or round. In every case the book must be placed in the press within boards. These boards are narrow strips, about 1/2 cm. thick and up to 5 cm. in width; they must be of equal thickness and bevelled only on long side, the edge itself must be rounded.
Many makers send out boards bevelled right from one side to the other.
This kind is very unsuitable and has many disadvantages. The boards must not be made from wood of very open grain, and firs and oaks must not be used. The boards are to be somewhat longer than the edge about to be treated, so that the edge may be as firm and tight as possible and at the same time easy to work upon; two outer boards are added to those regularly used, as shown in Figs. 49 and 50.
The inner boards are quite flush with the book: the latter must on no account stand back. The outer boards are about 3 mm. behind the others; the book is so placed in the press, and here again the book and boards must be exactly level with the press cheeks. The press is then screwed up as tight as possible. If the inner boards have not perfectly straight edges they must be planed down.
Figs. 49 and 50--Arrangement of flat and rounded edges.
The edges are to be scraped down quite smooth with a scraper or, if necessary, with a knife; the scraper must not be sharpened for this purpose as the carpenter sharpens his tools, that is, not to a cutting edge but as though it were for carving, until a bevel (or turned edge) of about 3 mm. has been ground. The edge thus gets a turned edge, with which the book is scraped. If it should cease to "take," the old edge is rubbed down with a steel and a new one made by a few firm strong rubbings. The edge should be wetted a little to prevent its heating.
Flat edges are scraped with a flat scraper, rounded edges with one suitably rounded. In this case the round of the blade must be more decided than that of the edges, as it would otherwise be impossible to get into all parts of the edges. Scraping with pieces of glass is an antiquated, clumsy method.
When scraping, the press should lie flat on the table edge, the other end being supported by the press-jack. In scraping, the blade is held in both hands, scraping away from the worker, the scraper sloping forwards.
The press must be made immovable. Scraping is continued until all places have been gone over and the whole is perfectly smooth and even. When this is accomplished, the edges are thinly coated with paste, which is well rubbed in along the sheets with a bundle of waste paper until the edges look as if burnished. It is advisable to damp the edges before scraping, as the blade then takes hold more uniformly.
Then bolus is mixed with glair as a body colour, laid on sparingly, very evenly, and free from streakiness, using a thick hair brush for the purpose. Bolus is sold to the trade ready prepared under the name "Poliment." Some time before using, it should be scraped into a suitable vessel and mixed with glair. The latter is prepared by adding the white of an egg to 1/4 litre of water and beating to a froth. It is then strained through a piece of linen or, better, through a filtering paper.
After the bolus ground has dried (which takes a few minutes) the gold is laid on. There are various methods of doing this. The surest and quickest way is to lay it on with the gilder's tip.
A row of long badger hairs is glued between two pieces of cardboard; this is drawn a few times over the hair of the head, which makes it take the gold easily. Gilders' tips are to be had at any colour dealer's.
Gold is taken from the gold book, laid upon the gold cushion, and cut into suitable strips with the gold knife. The gold cushion consists of a piece of calf stretched raw side out on a board. Between the leather and the board there is placed a pad of cotton wool, and over the wool a pad of blotting-paper. The gold knife is a thin, pliant, two-edged knife without a sharp edge, in fact it is better to blunt the fore-edge from time to time by rubbing it on a polished steel. If the knife is too sharp it will cut the leather cushion.
Taking the gold from the book will not be found a very easy task. The top leaf covering the gold is turned back, the book with the uncovered leaf of gold laid on the cushion, and the book slowly lifted up. The gold-leaf remains flat upon the cushion and may be cut with the knife as required. If a draught has turned the gold-leaf over or made it lie unevenly, it may be righted by lightly tapping with the knife on the cushion near the gold; careful breathing on the centre of the leaf will help in more awkward cases--the rest must be learned by practice.
Never attempt to take hold of gold-leaf with the fingers; only the experienced workman knows how to carry gold-leaf with a finger.
For gilding the edges the deep red gold is always used, or else the so-called orange gold, which is somewhat lighter in tone, but never the lemon or green gold.
For flat gilt edges the gold is cut about 3 mm. wider than the book and into as many strips as would make up the length of the edge if joined together.
Before laying on the gold, the bolused edge is brushed down with a hard clothes-brush to remove all hair, dust, &c. Glair is now liberally applied with a thick hair brush, laying it on separately for each strip.
The gold is now lifted from the cushion with the gilder's tip so that it very slightly projects over the end of the brush and is transferred to the wet edges. The tip is brought to within 1 cm. of the surface of the edges and with a quick motion the whole surface of the gold is at once brought into contact with the glaired edges, which will instantly take it up quite greedily. The gold slightly overlaps on to the inner boards.
In this one continues, preparing the edge for each fresh strip and laying on each strip so that it slightly overlaps the other until the whole length is covered with gold. If the gold should be injured in any way, the press must be tilted so as to allow a little glair to run under the gold to the spot and then a larger piece is laid over the faulty place.
When it is seen that all parts are completely covered, the press-jack is put aside, the press is taken by the screws between the beams and raised high overhead so that the gilded part is turned downwards. One end is carefully lowered until the glair has run to one side and dripped off. As soon as the greater part of the moisture has been removed, the press is either placed upright with the edge to the wall and head downwards or it is laid across the table where it will not be disturbed, with the head of one screw on the table edge.
In this way the moisture runs off quicker, as the whole length of the edge drains together. When dry, the edges are burnished, and it is in seizing the right moment to do this that the clever finisher shows his skill. The first test is made on the boards. If the gold comes off on scratching the portion on the inner board with the finger-nail, the edge is still too damp; if the scratching makes it shine, it will be all right.
The experienced worker can trace the progress of drying with more certainty by breathing on the edges; the slowness or rapidity with which the breath disappears points to the dry or moist state of the edges.
When it is believed that the proper degree of dryness has been obtained, the edge is polished with a burnisher. A piece of tracing paper which has been waxed on the upper side--that is, the side next the burnisher--is laid on the fresh edge to protect it from injury. The burnisher is then worked crosswise, stroke by stroke, over the paper (through which the edge can be observed) the length of the edge; if it is noticed that gold and moisture adhere to the paper near to the boards, the work must be laid aside to wait a little longer.
If, however, the whole process has gone on satisfactorily, the edge is gone over with a linen rag and a little beeswax. It is not at all better to use a silk rag instead of linen, for it happens too easily that tiny threads stick to the gold unnoticed and are afterwards rubbed into the edge. After going over the edge with the waxed rag, the bare edges may take a greater pressure in burnishing, and if no flaws are now perceptible there need be no hesitation in burnishing with very strong pressure.
The burnisher must be held quite level, the long handle fixed against the shoulder and the lower end firmly gripped with both hands just above the metal fastening. The fore-edge of the burnisher is not to be held parallel to the sheets, but must be at a slight angle; it thus slips better over the paper and there is less danger of making rills and furrows, and the polish is obtained more rapidly.
Flat edges are always burnished crosswise, but at the end a broad burnisher may be used for going over the edges lengthwise with a few slow, firm strokes, so as to ensure a very level surface.
Quick burnishing must always be avoided; it heats the gold, which rubs off under the burnisher, and causes holes which can never be remedied.
As soon as one length has been burnished, the waxed cloth must be applied before proceeding further.
Slight flaws in the gold itself, or due to bubbles in the glair, may be put right by touching the faulty places with a small brush dipped in rectified spirit and immediately laying on a piece of gold; if the edges had not yet been gone over with the waxed rag, it would be sufficient to breathe on the place, lay on the gold, and burnish under paper. This need only stand a few minutes, as it quickly evaporates, and may then be burnished again at once, first with, then without, the tracing paper. It must be observed that such faulty places must be burnished in the direction of the sheets, never crosswise.
Rounded edges are more difficult to work; the scraping alone being more troublesome. Each piece of gold is halved, laying on each time a little beyond the deepest part of the round. The press is so lowered as to give a decided slope to the half of the edge to be operated upon. The gold is cut to a little more than half width, and only the under side to a little beyond the middle is glaired, which in this case must be done very freely. The strips of gold-leaf are laid on as before. When one side has been covered with gold, the press is turned and the other half of the round similarly treated. Care must be taken that there is always a liberal supply of glair in the depth of the round.
To drain off the superfluous glair the press is placed so that the glair runs off on the long side; the gold is in consequence better taken up in the round.
Burnishing is here also done under a piece of paper, and it is better to work crosswise, first one half to the centre of the round and then the other. Only thin books are burnished along the edges with a round burnisher. After the round edges have been burnished crosswise they are burnished with the round burnisher.
Burnishers are made of agate or of bloodstone; the latter is said to produce a higher polish, but this may be due to our being more accustomed to its use. In selecting burnishers the flat ones should not be too wide and the strongest of the curved ones should be taken.
Top and bottom edges undergo the same treatment in gilding as the flat fore-edge, except for a few slight necessary differences in the method of fixing the book. In the first instance, long boards are used instead of the outer boards--these protect the book from injury. The boards (the short sides of cross-boards are often used instead) are laid exactly in the groove at the back, but the outer boards are set back so that they are exactly in a line with the depth of the round edge. If this precaution is neglected, the chances are that little ridges will appear in the fore-edge where pressure has been applied. Fig. 51 shows the arrangement in the press.
Scraping is done from the back to the fore-edge. As the back is not pressed so solid as the rest of the edge, it frequently happens that it does not get scraped so smooth. In this case recourse may be had to a fine file and fine sand-paper. The rest undergoes the familiar process.
Take care that no glair runs on to the fore-edge when applying it or when draining it off. It is convenient to place the press crosswise on the table so that the fore-edge stands at its lower side; the glair then drains off the whole length of the edge more evenly and drains more towards the fore-edge. Many finishers elevate the press, letting it drain towards the fore-edge; there is no danger to the latter if the press is tipped forward from the top. On no account must the glair be allowed to drain towards the back, as this part is very open and all the moisture would gather there.
Fig. 51--Top edge arranged for gilding.
Besides the method of laying on the gold-leaf with the gilder's tip there is another which is specially used in gilding hymn-books; a piece of gauze is stretched across a frame, passed over the hair, and then the gold for the entire length of the edge is at once picked up and laid on.
Round edges may be similarly covered by means of a couple of threads or horse-hairs stretched on a frame. The threads can be shifted to the short sides of the frame; they are adjusted to the width of the edge, allowing for the rounding, and are slightly greased by passing over the hair, and thus pick up the strip of gold at the edges. Just before laying on the gold, the threads are adjusted so that the gold fits the shape of the edge. Then plenty of glair is applied and the gold quickly and truly laid on.
This method is not exactly difficult, but it is not quite so safe as laying on with a gilder's tip, especially for very large edges.
The simplest way of laying on for flat edges is by means of strips of paper. This has the advantage of allowing a larger number of gold strips being made ready for laying on at one time. Select a piece of stiff and not too thin paper, cut into strips about the width of the strips of the gold-leaf, draw one side of the paper across the hair, and then take up the leaf so as to allow it to project a little over the edge of the paper strip. After glairing, strip by strip is laid on.
For very cheap work it is often necessary to gild edges with alloyed gold. Such edges are not so carefully and thoroughly prepared; in particular, they are not scraped, but rubbed down with sand-paper. Blood serum is used instead of white of egg; this is prepared by allowing ox-blood to stand a few days and then filtering off the clear liquid.
Aluminium is laid on a gelatine solution: one tablet of gelatine to 1/4 litre of water.
Gilt edges are also frequently tooled or scraped and painted. This work comes within the sphere of the art binder and cannot be dealt with in this book.
All other coloured and marbled edges can be burnished in the same way as gilt edges. In good work this must always be done.
In small shops headbands are made to this day of striped calico, which is cut into strips of 2 cm. wide right across the pattern, and one edge is pasted round a thin cord. After drying, pieces the exact size of the back of the book are cut off. The back of the book at the head is glued with a not too thin glue and the headband glued on so that the pad made by the cord lies on top of the edges and thus covers the place where book and cover join.
Fig. 52--Headband shears.
Woven headbands are now to be had so cheap that it is no longer necessary for the binder to make his own. The cheaper kinds are woven of cotton, and of these there are bands made which have two pads, each edge having a different colour. This band is cut along the middle for use; for the rest, it is cut into pieces according to the width of the book and then glued on to the back. Better kinds in silk are only woven on one side, therefore the cutting asunder is not necessary. For work in quantities, the headbands are cut the size of the back with the adjustable headband shears.
For extra work the headband is hand-worked in silk. This work can only be learned by practice, although its execution is not difficult; such books are only headbanded after boarding.
To make the filling for the headband, cut into strips pieces of vellum which have been pasted together, between which a piece of tough, thin pasteboard may be pasted to further strengthen. These strips are cut a little less than the height of the squares and a little longer than the width of the back. So as to facilitate the work, the strip is at once curved to the rounding of the back.
Take two silk threads of the kind sold as "Cordonnet" silk, each thread of a different colour. Both threads are threaded in a sewing needle, the threads taken double, the ends of both double threads knotted together.
The book is clamped in the ends of a press and stands slanting a little outwards. The needle is inserted in the back groove of the first sheet at the left hand underneath the kettle stitch and the thread drawn out to the knots. Thus one thread is always above and another below. The strip of vellum is now placed upright on the outside edge of the head, the thread is brought over from below, and is stitched from above to below close to the head, with the hanging needle through the first sheet under the kettle stitch outwards.
Bring the same thread once more up over the strip, let the needle hang in the hollow of the fore-edge, taking in its stead the other thread which takes up the first, bringing it out underneath the vellum strip. By this, the first thread is firmly drawn as a chain stitch into the headband now beginning.
The second thread is now brought upwards but need not again be taken through the sheet; it is taken back under the vellum strip once, and at the second time the needles are changed in the hollow as the first thread one more takes up the second thread and draws it into a chain. Thus the work goes on; after several journeys the thread is once again drawn out through a sheet until both threads are brought out at the other end of the back and pasted down. The first knots must also be undone and the ends pasted so that they do not show on the back.
It is essential that the vellum strips should be always firmly and evenly sewn upon the edge, and also that every winding of the thread and the chain lies quite regular.
Fig. 53--Headband working.
It is possible to make a variation by making a few stitches with a third thread of another colour in the centre of the headband. Any vellum projecting at the ends must be cut off flush with the book.
Some books are given a marker; this is made of silk ribbon or of a cheaper kind specially woven for the purpose. It is cut long enough to allow of its projecting a little at the head and pasted there, and at the same time comfortably held by the finger at the corner diagonally opposite. The marker is glued on before headbanding.
CHAPTER V.
BOARDING.
The boards may be fastened to the covers in various ways, apart from casing, i.e., fixing books in publishers' ready-made cases.
- Fastening upon bands (ordinary fastening).
- Fastening below bands (fastening on a deep groove).
- Drawing the bands through the boards (fastening with laced
bands).
The boards for the books are nowadays manufactured from pulp, excepting in a few districts in Pomerania and East Prussia where wood boards are still occasionally made. Of these pulp boards the better kinds are called mill-boards; the cheaper are called straw-boards. Leather boards are not suitable for books as they invariably wrinkle or cockle. The boards may be cut to size before fastening on, or this may be done even after the fastening on has been completed. The former is generally practised where there is a board-cutting machine, but even then further attention is usually given to the shaping of the boards in the case of "extra" work.
The board-cutting machine is a very useful ally, for by the aid of quickly adjusted rectangles and parallels a board may be cut perfectly true.
The boards are selected according to the size and thickness of the book, marked out, and cut perfectly rectangular. The boards must slightly project at top and bottom as well as fore-edge so as to afford sufficient protection to the book. The margins so projecting are called the squares. Small books are allowed a small square, as a matter of course, and large books a square correspondingly larger.
Fig. 54--Board-cutting machine.
Where there is no board-cutting machine, the boards must be cut to size with the knife upon a cutting-board, using a straight edge for the line.
The knife used is the well-known bookbinder's knife--Henckel Bros.'
Solingen make is the best. These knives--both in fixed and removable wooden handles--are made of "glass hard" steel. If the point is worn away, a piece about 1/2 cm. long is knocked off with a hammer on an iron edge, thus making a fresh edge. The cutting-boards must be of maple, beech, or pear tree.
If it is intended to shape the edges of the board on the book, it must be cut about 1 cm. larger each way so as to allow for further trimming.
Fastening the boards to the book is called "boarding." This can generally be done as well with paste as with glue; the former is preferable but necessitates longer pressing and drying. Glueing is quicker, but the bands cannot then be pressed so evenly into the boards.
For ordinary fixing on the bands, the insides of the boards are pasted to about 3 cm. in width, the bands also pasted, and the board laid on, bringing it well up to the groove. If it is intended to glue up, the bands are also glued, provided they have not already been glued on--a method preferred by many experienced hands. The bands must be pasted so that they radiate from the back without any tangle; a morsel of paste the size of a pea is laid on the band from underneath with the folder or point of a knife, the band smoothed down, and the thing is done. After glueing-up, the book is pressed between boards.
If zinc plates are placed under the boards whilst pressing, the pasted parts will be pressed quite smooth and shiny.
Fig. 55--Spring back.
For cloth or half-cloth binding a hollow back is frequently glued on. To make the covering material of the back more lasting, a back is made up of strong wrappers or some other tough material, which extends over the back underneath the cover. This backing material must be cut 4 to 5 cm. wider than the width of the back and about 1 cm. longer each way than the book. This strip is pared very narrowly along both sides with a sharp knife on the so-called paring stone.
A second strip--the backing--of the same material is cut the same length but exactly the width of the back of the book and is glued on to the middle of the wider strip. The overlapping parts at the sides are broken in towards the middle, close by the inner packing, and the crease well pressed down with the folder. These overlapping edges are then turned back again and a rule is laid on the packing parallel with the edge but drawn back to the middle about 2 to 3 mm. according to the thickness of the cover.
If the moveable flaps are now again laid over towards the centre and narrowly creased near the first fold over the rule, a second parallel fold is obtained which allows the book to open much better. The back in section appears as illustrated in Fig. 55 after the middle part of the packing has undergone the necessary rounding.
Fig. 56--Boarded book.
Rounding can be done either by rubbing the middle part round with a proper wooden tool in a rounding board having several hollows of various degrees of convexity, or by drawing the back with a rocking motion under a broad folder. Such a made-up back must fit perfectly true to the groove and on the back. This is the hollow back. Before fastening it to the book, the latter must have a piece of stout paper pasted over the back; good packing-paper is the best. Newspapers and loose advertisements out of magazines are not at all satisfactory and must not be used. The book is glued and the paper laid on and glued. In doing a large batch the books may be pasted in the press and the paper pasted on.
Many experts glue the hollow backs on and use paste for the board. Very frequently the glue comes through and spoils the end papers. It is better to raise the flaps of the back, paste the tear off of the end paper, paste the bands on to it, and the loose flaps as well, and then paste this on the outside and set the board on it. The latter must be set back a little further in this case so that the book moves freely in the joint. The back, therefore, is a hollow arch stretching over the book from groove to groove, the loose flaps of the packing adhering between book and board. The book is pressed until thoroughly dry--best between zinc plates.
Fig. 57--Section of edge rule.
For shaping boarded books an edge rule is used. This is a thin iron rule not much longer than the width of the book. On the long edge an iron pin about the width of the edge is soldered. This tool is inserted between book and board so that the iron pin lies close to the edge of the book; if the board is trimmed along this it will leave the board exactly as much larger than the book as is the width of the rule.
Knives or points must be well grasped in cutting boards. The edge must be clean and square.
If the boarded book has a hollow back, first one end is shaped and the projecting back is neatly cut clean and straight to the other board with the shears, and then the other end is shaped.
Boards are fixed on a deep groove by pasting them on the outside to a width of about 3 cm., placing them direct on the book, backing them firmly into the groove, and then pasting the bands very smoothly upon the boards. A folded piece of waste paper is placed on the pasted part, a piece of zinc plate over it, and the book then pressed. The double leaf is used to prevent any sticking to the zinc plate, which bands are particularly liable to do if the plates had not been properly cleaned after previous use.
Boards to be fastened into a deep groove must be lined with waste paper; this is done with paste. When packing, a narrow strip of paper must be brought over the inner edge of the board in the groove to the outside, so that the cut edge of the board is covered and does not strain or swell.
This is also done when boarding, as follows:--
At the present time, all good half or whole leather bindings have the boards laced through in good shops. At the outset the bands must be left with longer ends for this--5 cm. at least on each side. A parallel line is marked on the board along the back about 6 to 8 mm. from the groove.
The board is fitted on the book just as was done when fixing in the groove, and exactly opposite each band a point is made on the marked lines. The board is then removed and at the points marked is pierced slanting inwards--about half right angle--with a pointed awl. The board is turned, and sideways, near every first hole, a second hole is made which likewise takes a slanting direction to the board. The bands are drawn through these holes, and to be able to do this the bands must be well pasted and twisted to a point; cutting off the extreme ends of the bands will facilitate the drawing through.
To draw the bands quite firm and tight the boards are stood upright in the groove, the bands drawn through as tight as possible, and in this position--that is, with the boards half open--they are knocked down with a hammer upon a firm bed.
The principal thing to be observed is that the bands are pasted fast in the holes, but where they are seen they are knocked down quite flat. The boards are now slowly closed, the ends of the bands projecting at the outside are cut off short, and the book pressed, using zinc plates inside and out.
Fig. 58--English style of lacing boards.
The French method of lacing is not much practised in other countries; it is somewhat more roundabout, and is done before cutting--immediately after glueing up. The boards are each shifted to right or left for cutting and cut together. By so doing, the edges always correspond exactly to the back groove.
Illustration: Pressing Board Profile.
For every band there are three holes bored forming a triangle. The awl holes are directed towards the middle of this triangle. The band must describe this course. The end is pushed under the piece of the band seen on the inside of the board, the bands drawn tight, with board standing upright as before described, also well knocked down in the same way, and the end cut off just beyond the piece under which it is drawn. The book is then pressed between zinc plates.
PART II.
THE COVER.
Formerly only one way of making the cover was known, and that was the gradual making of it on the book itself. This has been considerably changed of late owing to the production of immense quantities for publishers' requirements. Book and cover are now in many cases made separately, the former being afterwards glued into its cover or "cased."
The publisher's case is nowadays a necessary evil, without which we cannot get along and which we have got to take into account. In spite of it, bindings are still being produced in the old approved way, particularly in small establishments and in high-class shops. Before we proceed with the preparation of the cover after the trimming, we must know how it is intended to treat the book. In the preceding chapter we have learned the methods of boarding, and this now leads to the methods of covering.
Previous to that, however, we would like to give a plan showing the various ways of treating the volumes under consideration, and then the chapter on the covers may be given (see plan on page 94).
VIEW OF THE MOST GENERAL STYLES OF BINDING, SHOWING THE DIVISIONS OF THE
WORK.
Table of Headings:
Col. A: Folding. Pulling to pieces.
Col. B: Sewing.
Col. C: Hollaendering.
Col. D: Gluing. Pasting.
Col. E: Pressing. Cutting.
Col. F: Marbling and gilding edges.
Col. G: Rounding. Backing.
Col. H: Boarding.
-------------------||------------------------|
## || WORK ON THE BOOK. |
||------------------------|
|| |
|| Forwarding. |
|| Second|
||First stage. stage.|
||--|--|--|--|--|--||--|--|
Style of Binding. || A| B| C| D| E| F|| G|H |
-------------------||--|--|--|--|--|--||--|--|
Brochure ||--| |--| | | || | |
|| | | | | | || | |
" Paper boards ||--|--| |--|--| || |--|
|| | | | | | || | |
School books ||--|--| |--|--| || | |
|| | | | | | || | |
Half cloth (bound) ||--|--| |--|--|--||--|--|
|| | | | | | || | |
" (cased) ||--|--| |--|--|--||--| |
|| | | | | | || | |
Whole cloth (bound)||--|--| |--|--|--||--|--|
|| | | | | | || | |
" (cased)||--|--| |--|--|--||--| |
|| | | | | | || | |
Half leather ||--|--| |--|--|--||--|--|
|| | | | | | || | |
Half calf, extra ||--|--| |--|--|--||--|--|
|| | | | | | || | |
Whole leather ||--|--| |--|--|--||--|--|
|| | | | | | || | |
Publishers' cases ||--|--| |--|--|--||--| |
|| | | | | | || | |
Table of Headings:
Col. I: Making the case.
Col. J: Covering.
Col. K: Pressing.
Col. L: Preparing the leather.
Col. M: Covering.
Col. N: Fastening the book in the cover.
Col. O: Pasting down.
Col. P: Jointing.
Col. Q: Pasting down end papers.
Col. R: Hand tooling and decorating.
-------------------||-------------------------------|
## || WORK ON THE COVER. |
||-------------------------------|
|| |
||Casing. Covering.
Finishing. |
|| |
||--|--|--||--|--||--|--|--|--|--|
Style of Binding. || I| J| K|| L| M|| N| O| P| Q| R|
-------------------||--|--|--||--|--||--|--|--|--|--|
Brochure || | | || | ||--| | | | |
|| | | || | || | | | | |
" Paper boards || |--| || | || | | | | |
|| | | || | || | | | | |
School books ||--|--| || | || |--| | | |
|| | | || | || | | | | |
Half cloth (bound) || | | || | || |--| | |--|
|| | | || | || | | | | |
" (cased) ||--| |--|| | ||--|--| | | |
|| | | || | || | | | | |
Whole cloth (bound)|| | | || |--|| |--| | |--|
|| | | || | || | | | | |
" (cased)||--|--|--|| | ||--|--| | | |
|| | | || | || | | | | |
Half leather || | | ||--|--|| |--| | |--|
|| | | || | || | | | | |
Half calf, extra || | | ||--|--|| | |--|--|--|
|| | | || | || | | | | |
Whole leather || | | ||--| || | |--|--|--|
|| | | || | || | | | | |
Publishers' cases ||--|--|--|| | ||--| |--|--| |
|| | | || | || | | | | |
CHAPTER VI.
MAKING THE COVER.
The boards for making the covers are cut the required size exactly as when cutting for glueing; a packing of thin cardboard or thin wrappers is cut for the back. The width of the back from first to last sheet is carefully measured by laying across it a strip of paper, the dividers are adjusted to the measure, and this is transferred to the wrapping paper. The packing is cut to suit the boards in height. When cloth only is used for the cover, the cloth is cut 2 to 2-1/2 cm. longer and about 4 cm. wider than the packing.
The width of the back depends upon the question of cost or other consideration. In whole-cloth bindings the cloth is, of course, cut in one piece and 1 to 1-1/2 cm. larger all round than the boards and back taken together. Glue is always used for cloth. As piles of pieces of cloth shift about in glueing, a touch of glue is given to two corners of the pile and left to dry a little. These corners hold the pieces of cloth in position whilst being glued and prevent the edges from being smeared.
In glueing cloth it must be seen that the glue is well rubbed into the grain or artificial indentations.
For covers which have only the back made, the packing is laid upon the middle of the glued cloth and the boards hinged on right and left at side of it, leaving, however, as much space between as is required by the joint and the thickness of the boards. As a rule, the space required will be as much as the thickness of the board. In making leather backs one allows a little more.
The cloth back is at once turned in at head and tail after the boards have been laid on, and the cover rubbed down in the groove with the folder.
Turning-in is done by pushing the side to be operated on a little over the edge of the table, and with the thumbs the cover is pressed over the edges of the boards with a sliding motion, whilst the forefingers hold the cover underneath.
Whole-cloth bindings are turned in in the same way, but in this case the corners must be first cut off obliquely as shown in the illustration.
Fig. 60--Corners cut for turning in.
The cloth is cut off at the corners so close that only as much as the thickness of the board remains. Thick boards have therefore more cloth left at the corners than thin ones.
Fig. 61--Corners: Right and wrong.
The top and bottom edges must be turned in before the fore-edge. At the corners, the cloth is nipped a little with the folder, without, however, making an oblique fold; there should rather be a hollow round turn-over remaining which is only drawn on with the fore-edge, then from the corner slanting to the board.
The edges must always be turned in quite sharp; there must never be a hollow place on the edge of the board. On the other hand, it looks bad if the edges have been much rubbed down with the folder, at least with cloth; it is different with leather.
The turned-in cover is turned and the front side well rubbed down under paper with the folder. When cloth has once been glued it must not be allowed to lie long as it rolls up and sticks together, which renders it practically unworkable.
The finished covers are laid between pasteboards to dry; only when the drying has to be done in a hurry may they be hung on stretched cords.
The latest in this work is a case machine which turns out 550 cases per hour.
When leather is used, it must first be pared, that is to say, the parts to be turned in where it is too thick in the joint must be gradually thinned.
Fig. 62--Paring with Offenbach or Berlin knife.
The paring knife, of which there are various kinds, is used for this work. The best known and the most generally used are the Offenbach and the Berlin, both very much alike except for a slight difference in the edge. The quickest paring knife is made after the French pattern.
This knife is called a "thrusting" knife because of the manner of using it, in contradistinction to those generally used with a cutting motion; but even these a skilful worker will be able to use with a thrusting motion. The under side of the paring knife is covered with leather.
A lithographic stone or piece of marble will serve as a bed upon which to pare the leather. The stone is set in a frame under which there is a bar to hold it against the edge of the table so that it does not work backwards whilst in use. All edges are rounded off and the surface is ground and polished.
Ability in paring does not entirely depend upon the skilful use of the knife but also upon the way the left hand manipulates the leather and upon a thorough knowledge of the nature of the leather. It should not be forgotten that the latter has a grain, though very few bookbinders pay any heed to this. With many leathers it is a very difficult matter to pare against the grain, especially pig-skin and cow-hide. One may generally take it that a leather pares best in the direction in which it stretches least. The grain runs from the back to the sides.
The Offenbach knife is narrower and ground more to a square point than the Berlin knife, the edge of which forms a sort of half right-angle to the blade. See manner of holding the knife in Fig. 62.
Quick working is an advantage of the Offenbach knife, which is due to the fact that less attention need be given to holding the leather on the stone, and paring proceeds from left to right, the left hand at the same time helping to push the knife. The Berlin make pares from right to left; here the blade is held almost parallel to the edge of the leather, the point of the knife inclining to the leather; with the other the edge is cut over slantingly with the point outwards.
To use the French knife requires more practice; the cutting edge is almost at right angles to the knife, and, besides, the method of holding it is somewhat unusual. For paring all thick leathers or large surfaces it surpasses all other makes in execution. To make the leather more workable for paring it is previously manipulated, that is to say, it is turned flesh side outwards and rolled to and fro, whilst firm pressure is applied with the second and third fingers of the right hand, thus making it pliable.
Fig. 63--Paring with French knife.
In an ordinary bindery thin or split leathers are mostly used; these do not require very much paring, which is only necessary for pig-skin and the finest moroccos. The latter leather is narrowly pared about 2 to 3 mm. wide along the edge for half as well as for whole bindings. Only the back is pared the whole width, therefore 1 to 1-1/2 cm. has to be nicely gradated. Broken places, inequalities of the edge, or even holes to be filled in, greatly add to the difficulty of the work.
In the thicker skins also--thick places often occur in the otherwise thin skins--the joint must be thinned down. The packing is laid upon the wrong side of the leather and its position marked out with the folder.
The leather is pared about 1 cm. in width along this line, that is to say, it is pared so that 1/2 cm. right and left along the mark the thickness of the leather is reduced.
As a rule, first-class books are not provided with a cover made in advance, and even those described by publishers as "super extra" do not rise above morocco goat.
We have to do with the following leathers which are mostly used for the publishers' bindings: Goat-skin (of oriental hybrid sheep), morocco goat, sheep-skin (unsplit sheep-skin), and split sheep-skin [or so-called skivers]. There is another goat-skin, not Levanted, sold and used under the name "bastard" leather. "Levanting" means to imitate by pressing the grain natural to the skins from the Levant. Most kinds of our leather receive their grain by such process.
For whole-leather bindings a narrow margin is pared down all round the edges, the turn-in at the back is pared just as much as is necessary, and also at the corners. The leather corners are cut slant-wise at the outset, and the paring is done so that the thinning begins exactly at the edge of the board.
In leather bindings the board, as well as the back packing, is glued on, rubbed down, and the edges then pasted and turned in, the leather is rubbed down sharply in the joint, the back, and on the edges; but a folder must never be used on the leather covering the board itself.
It frequently happens that the board is finished off with round corners; in this case, the method of turning in cloth as well as leather is slightly different. The two neighbouring edges are turned in. The leather or other material is cut off not quite so close as for square corners, and the material is drawn very smoothly and neatly over the edges in little folds, using a pointed folder for the work.
Illustration: Cover corner shapes, 1
Illustration: Cover corner shapes, 2
Books not wholly covered with cloth or leather get corners of the same material as is used for the back. Cloth corners are not cut singly, but a strip of material long enough for the required number of corners is glued and then cut with the shears into pieces of this shape or, better, placing them on the boards in such a way that the material projects a little over the corner of the board. First of all, the lappets of the top and bottom edges are turned in, the corners nipped in the manner shown, and then the lappets of the fore-edge are also turned in.
Leather corners are treated in the same way, but these are cut from waste pieces according to the zinc stencil plate kept for the purpose, and then pared down.
Illustration: Cover corner shapes, 3
Glue is used for fixing on cloth corners, but strong paste is always used for leather. All edges and corners are well rubbed down with the folder and left smooth and sharp, but, on the other hand, the grain on the board side must be left uninjured. Insufficient paring of the corners or using only the fingers for turning-in causes very thick edges; such work is out of date and would not be done by any thoughtful workman.
Illustration: Half cloth or half leather corner.
Books bound in half-cloth or half-leather have the sides covered with paper; the latter often with cloth. When cloth sides are used, the material must always harmonize with the back both in regard to colour and texture. On each side to be turned in the paper is cut 1 to 1-1/2 cm. larger than the surface of the board to be covered. The paper is cut along the back with the knife and rule. The corners are turned down in half right-angles according to the size of the cloth or leather corners and somewhat smaller than these, and cut off with the shears as shown in the illustration, using the fold as a guide.
Illustration: Small corner diagram
In ordinary work with very small corners, especially in large quantities, the corners may simply be cut off diagonally, and if there are many covers they are knocked up and the cutting is done with knife and rule or with the machine.
As a trade article for the publishers, the finished cover is lined with paper on the inside, both for the sake of improved appearance and to prevent the drawing outwards. For every board a sheet of paper is cut about 1/2 cm. smaller than the board and pasted on. The covers are placed between boards to dry.
Covers are generally decorated in some way; as a rule by means of the blocking press. Where they get any hand tooling, it is always done on the book when bound, for which no case is made in advance. Simple gold lines along the back and corners of the cover are excepted; such work is known as "filleting."
CHAPTER VII.
WORK WITH THE BLOCKING PRESS.
We make a distinction between gold tooling and blind tooling. The latter is simply an impression on the leather or other material without the use of gold, whilst the other is an impression upon a specially prepared leather or other surface, using gold leaf.
Skill in blocking depends first of all upon a tasteful and suitable selection and arrangement of the engraved blocks and letters necessary for the decoration and inscription.
The blocks, &c., are to be had ready made from the engravers in properly arranged sets; but still it is essential that the finisher should possess certain artistic taste and feeling, especially in making up the lettering. It must be borne in mind that in an inscription or title the principal part (word or line) must be distinguished by larger or heavier type; furthermore, two lines of equal length must never appear in an inscription. Short words (the, and, for, &c.) worked into an inscription as separate lines add considerably to its appearance. See pp. 148 to 153 for what is said on the arrangement of the title in hand lettering. The same applies to the arrangement of all lettering.
The blocks and letters are always fixed to the upper part of the press--the platen.
To enable alterations to be made quickly or to secure pieces which may have slipped, there is a draw-out plate made in all modern blocking presses. The engraved blocks are not affixed to this plate with glue but with cobblers' wax. The following is a practical way of managing the ornamental blocks: On a thin but very strong board about the size of the article to be blocked, the blocks are arranged with the backs uppermost, the engraved face being next to the board.
This board is fixed with wax exactly in the centre of the lower part of the press--the table. By "exactly in the centre" it is to be understood that the centre of the various blocks brought together lies on or near the centre of the draw-out plate. If there are more and heavier blocks fixed to the upper than to the lower side of the plate, the latter must be lowered a little--in a word, the plate must be so adjusted that all parts receive equal pressure. It is only by making a few trials that one can learn exactly what is right.
The press should be warmed by this time, and it is well to slide in the table with the blocks adjusted upon it, and to let it remain under light pressure until plate and table are warmed throughout and no trace of moisture may be seen on either. Now put a little wax on each block, lay over them a piece of stout wrapping paper, cardboard, or similar stuff, push in and press gently; the wrapper also may be waxed. After about five minutes, open the press to see whether all parts have stuck. Until this takes place the press must remain closed.
If, however, all pieces are sticking fast, draw out the table and examine the imprint of each particular part to see whether the pressure is equal; if this is not so, it remains to be seen whether such inequality is due to a faulty fixing of the plate and, if necessary, to rectify it; otherwise, pieces of paper must be made up into a suitable packing and laid upon the back of the blocks until all inequalities are removed and an even impression is obtained.
This done, the back of the set-up blocks, or the wrappers affixed thereto, is waxed at as many places as required, or rather as far as the set-up blocks extend, the plate pushed in, and the press closed until the set-up blocks adhere to the upper plate. The lighter this first impression is made, the easier it will be to detect any inequality on the table (or matrix) and to set it right by backing up with paper.
Fig. 64--Blocking press.
Before proceeding further, a few words must be said about the construction of our modern blocking presses. For modern blocking we use knee-lever presses, whilst balances are now no longer used.
On the upper part there is a sliding plate--the so-called platen--which draws out on prismatic rails.
A second plate works on hinges at the side of the sliding (or draw-out) plate and can be pulled out to the left. This plate is used principally for colour blocking--the other plate for gold.
Blocking can be done in gold and colour immediately after each other, and if the plate is in duplicate, four impressions can be made in succession without having to take off and change the plate.
In the upper plate there are round borings for the gas burners or hot irons used for heating the press; the latter are out of date and do not produce a steady temperature.
It now remains to insert the article to be blocked in the press so that it will be blocked exactly on the spot required.
There are several ways of attaining this object, which are adopted according to the kind of work in hand. The surest way is to mark the place by pins.
Two large drawing pins are pasted upon pieces of cardboard, a second piece of board is placed over each one so that the head is embedded between the two pieces but leaving the points free. The gauges thus made are fixed with wax at convenient places, best on the middle line above and below the table but in such a way that they themselves are not touched by the plate. To prevent their falling off, a larger piece of cloth is pasted over them, always leaving the points visible. The surest preventive against falling off is to have screw-on gauges. A strip of metal having a slit in the middle can be screwed tightly to the table by means of a screw passed through the slit.
At the end a steel point about 1/2 cm. long is riveted on. With this gauge the points can be adjusted to any position on the table as required.
All work not turned-in which requires repeat blocking, and all such as requires blocking in more than one colour, is "pinned on." On the other hand, covers which are finished after being once blocked on back or side which require no second impression may be adjusted with the angle gauge or blocks. Many make use of both at the same time. Such covers then have been turned in all round when being worked, whilst "pinning on" requires that the covers should not have been turned in.
The practical bookbinder who has to deal with turned-in covers frequently gets over the difficulty by making two incisions about 2 cm. apart with the knife upon the turned-in edge at the place where it should be pinned on, and opening out the material at the incisions, thus making a loose margin for pinning on.
For pinning on covers as well as backs, a template is cut from wrappers or thin board, which is adjusted on the cover and the register holes made with an awl. When pinning-on has to be done for blocking which has to be repeated very many times, the register points are strengthened behind with stiff paper to prevent them from breaking or tearing away and thus becoming inaccurate.
Fig. 65--Appliances used in blocking backs.
To enable the most various widths of backs to be quickly inserted and to supply a substitute for the thick layers of cardboard packing which make a fine impression impossible, a special contrivance with metal pads has been made. This is shown in the sketch herewith.
Mention has already been made of the table (or matrix). This is a bed of stout boards which is intended to serve the double purpose of saving the blocks when blocking thin articles (backs of covers, &c.) and also for strengthening and equalising the resistance from below when working on heavier articles. Faults arising during working, such as insufficient adhesion of the gold (and an increased pressure) may be set right by pasting on pieces of paper to the matrix or table.
The matrices consist of strong but thin material; the best is wrappers or the thinnest board. After use they are kept for subsequent repetitions of the same or for other work.
The lettering must always be set up fresh for each job, whilst the ornamental pieces may be arranged on the tables or matrices at hand after the existing original impression.
Setting the type is a special art and calls for considerable taste and skill; the letters very easily slip out of the type-holder, especially where very small type is used, unless special precautions are taken to prevent this. Here we will pass over the most important point in the arrangement of the types and refer to the paragraph dealing with "Lettering" under "Hand-tooling"; what holds good there always holds good here.
Lettering is always set upon special pieces of board and afterwards encased in a type-holder, as it demands much more attention and subsequent correction. These boards should likewise be wrappers of the same thickness as those used at the same time for the ornaments. For fixing, cobblers' wax is likewise used. The favourite method frequently adopted of using glue coated with paste is not to be recommended, because the letters do not admit of proper setting upon this gelatinous mass.
Not only do the lines of letters require to be kept right by means of a strip of metal or metal line, they must be carefully adjusted after taking a light impression, especially when using a very small type. The first pull must be under so light a pressure that on a soft paper everything is distinctly visible. The lines are arranged from this proof, whilst each single letter is carefully checked. Where letters do not show up properly they must be backed up with paper of suitable thickness on the board until all unevenness disappears.
The lighter the pressure applied the easier it will be to make corrections. Letters heavily pressed at the outset can seldom be properly rectified afterwards.
In large editions it does happen, in spite of all precautions, that single letters work loose and fall out; this may damage parts of the plate as well as valuable covers, and one therefore tries to guard against it. Some take narrow strips of cloth and paste one round each line of type, others pour liquid glue between the lines which, when thoroughly dry and hard, is a very sure means of preventing the falling out of any piece of type.
When everything is in order, the type is likewise inserted; various parts of the back of the board are well waxed and the table is then pushed in and the press closed tight. It remains closed until all parts are thoroughly dry, for it is only then that we may feel assured that no parts can fall out. The drying may be hastened by opening the press about a quarter of an hour later and drawing out the plate, likewise the table, and now allowing plate and table to dry by exposure. If any parts of the plate should lift, wax must again be applied and once more pressed.
When the plates and press are got into working order, and the backs or covers have received their register marks by means of the template, the blocking may be commenced. The table is drawn out, a piece of work pushed in to the register, and the press closed. It is necessary that the press should have been previously regulated to the thickness of the article being blocked, and to begin with a light pressure at first, as heavier pressure can be applied afterwards if required. Cloth requires sharper pressure than leather.
Large heavy covers are always blocked with the press quite closed, whilst small things like single titles, hat linings, ties, &c., are finished with only a short pull of the lever.
The correct regulation of the pressure rests with the worker.
We distinguish between blocking in blind, gold, colour, and relief.
Blocking in blind, both on leather and cloth, should not be attempted upon articles which have become very dry. A good plan is to store them in a cellar the night before and to bring out only as many as can be finished in the next half-hour's work. Blocking in blind can only be done on matt or grained material, as its effect is nil upon a smooth polished surface.
The finish can be considerably heightened in special cases by going over the impression with a brush and white of egg after the first blocking and then again pressing under less heat. Calf leather, and undressed calf in particular, receives its splendid brown colour by being previously damped with boiled or distilled water to which a little spirit has been added. The impression on a damped ground is first made somewhat warmer and afterwards repeated when the press has cooled a little, occasionally wiping the blocks with a waxed cloth.
The impression must in all cases be even in colour and have a high finish; if this is not so, the lighter places must be once more damped with a small brush and again impressed.
Articles to be blocked in gold must be prepared with some substance to which the gold will adhere. The finisher uses a fluid or dry adhesive according to the material he is working upon. Of liquid sizes, diluted white of egg or, in some cases, dissolved gelatine or blood serum is used almost exclusively. These liquids, which are applied with a sponge or, for fine work, with a brush, are called the "ground" or "sizing." Of dry adhesives, we know only the gilding powder, which consists of resin with now and then an addition of dried white of egg.
The other powders used by the finisher are rice flour or potato flour; these are not used as adhesives but to prevent the gold sticking at places where it is not wanted.
Leather and cloth are sized with white of egg; silk and other woven materials are finished without special sizing, and also surfaced papers and cardboard goods, as they are treated with finishers' powder, a wet preparation being unsuitable.
Size for blocking is thinner than for hand finishing, and when it has to be washed over the whole of a cloth cover it is still further diluted.
Glair for brushing over an impression consists of one part white of egg and one part vinegar; to every 1/2 litre 1 g. of powdered borax is added, the whole beaten to a froth and filtered. For coating-over, take one part white of egg, two parts water, and to every 1/2 litre add 10 drops of glycerine and 1 g. borax. If a larger quantity of glair is required for coating over, it may be thinned with water or vinegar; but size made with vinegar must not be applied to fancy coloured cloths.
Gilding powder may be yellow or white, the latter kind is rougher and is suitable for silk stuffs and also where blocking has to be done over colour on cloth. Yellow powder is softer and is apt to clog the finer cut tools; it is more suitable for the preparation of paper de luxe, for blocking surface and chromo papers, and for photo cases.
Gilding powder is sprinkled by means of a box which has a double layer of fine gauze instead of a bottom. By tapping upon the box a fine shower of powder is dusted on to the surface to be gilded.
Glair is made in the workshop; the powder is bought ready prepared--to make it would take too much time.
For blocking in alloyed metals, gelatine size is used, as it is a powerful adhesive. A tablet of gelatine is soaked in 1/4 litre of water overnight and next morning is dissolved in the bath. Gelatine is used to cover the whole surfaces and is laid on when lukewarm. Blood serum serves the same purpose. Ox blood is allowed to coagulate, and the hardened mass thus produced is placed over a cloth strainer, or hair sieve, and the liquid albumen allowed to drain from it; the process is hastened by cutting the caked blood into small pieces. Only the clear liquid which is strained off is to be used--a pinch of borax will make it keep longer.
For finishing bindings, real gold-leaf--orange tint--is used almost exclusively, the cheaper green gold being used only for sample cases and school books. Alloyed metal and aluminium (this is now commonly used instead of the quickly oxydizing silver) are used almost solely in the manufacture of papers de luxe and for placards.
Pure gold-leaf is always laid on the sized cover after the surface to be blocked has been lightly gone over with a ball of oiled cotton wool, or a slightly greased rag. This must never be done to such a degree as to cause grease spots. Calf must not be thus treated with grease, but if the gold is not likely to stick at certain places, the first impression may be picked out with a brush slightly oiled so as to make the leaf adhere. Dark polished calf will, however, stand a little oil.
Fine leathers are first stamped and the impression is gone over with a brush, then the gold is laid on and again impressed. The gold is lifted from the cushion with a gilder's tip or a pad of cotton wool and transferred to the cover. The gilder's tips consist of square pieces of cardboard a little smaller than the piece of gold to be used, to the under side of which is pasted a piece of cloth. A handle of cardboard or a button is pasted on top for convenience of holding.
Draw this tip lightly over the hair, press it on the gold, which will lightly adhere to it, and then transfer the gold to the surface to be stamped, where it is pressed down with cotton wool, which should be surgical wool, as that kind is free from knots. Many prefer a tuft of cotton wool rolled into a handy size, this is likewise drawn over the hair, and the rest done as before.
When gilding powder is used, the gold must not be laid on with the pad.
The gold must be placed on the powder by hand only, a task calling for considerable adroitness. The gold is taken up with the gold-knife, aided by a moistened finger-tip taking a corner, passed over the surface with the knife, brought to the required position with the hanging corner, and now the knife is taken away flat sideways. The gold must lie quite even on the powdered surface. Any subsequent shifting of the gold is entirely out of the question, because the layer of powder would be disturbed and might not hold in places.
To know exactly what degree of heat should be applied requires special study, and the pity is that fixed rules cannot be given--one day a black morocco goat-skin may stand a great heat, whilst on another day the same heat applied to similar stuff might burn it up. Cloth is always the same, calf leather papers, skytogen, &c., are much more difficult. On the whole, the following rules may be observed:--
Cloth white of egg (or glair) medium heat
Sheep-skin " slight heat
Goat-skin " medium heat
Morocco " medium heat
Silk white gilding powder short hot pressure
Surface
papers and
cardboards yellow " " short medium pressure
Calf glair hot (light leathers
somewhat less heat)
Varnished paper little heat
The latter contains sufficient adhesive matter in the colour without using any other size, even for alloyed gold, but the covers must, however, be slightly moist. For this purpose they are left overnight in a damp cellar or placed between slightly damped boards.
We have already spoken of the matrix. Where silk or other thin woven materials are to be blocked, a firm hard board must be laid on the table and frequently changed, otherwise the impression will be defective. For ribbons for wreaths, &c., a suitable piece of paper which had been damped some time before should be laid underneath.
Although relief blocking upon bindings seems to be out of favour, there are numerous styles of imitation relief practised nowadays, especially in imitation of cut leather or wrought metal. This work necessitates the matrix or table being prepared with great care, as it must be the counterpart of the plate. For this purpose an impression is first made upon a stout cardboard, which is fixed firmly enough on the bed to prevent its shifting, the block being affixed to the platen. Upon this first cardboard are laid the raised parts according to the height required, likewise cut out of stout cardboard, continuing to place a layer upon the other until a true negative of the block is obtained.
Small and slightly raised ornamentation is not specially underlaid, using instead a piece of stout board well smeared with cobblers' wax, which, after standing awhile under the plate in the closed press, will make a very exact and firm base. Matrices made up of several layers of cardboard pasted on top of each other are also, when finished, covered with a piece of pasted packing paper and then pressed. This leaf prevents single pieces from working loose and sticking to the block.
For relief stamping, leather or cloth is stretched upon thin wrappers.
The guide points must be made a little further apart on account of the material shrinking slightly under relief stamping.
Colour blocking, which has gained such unexpected popularity, gives the finisher no little trouble. As blind blocking is done by the press, so also may colour blocking be done if the blocks are coloured with the brilliant colours specially prepared for printing. A colour roller, made by moulding English roller composition on a wooden pin, is used for colouring the blocks. The worker himself may cast these rollers in a well-greased mould.
The roller composition is dissolved in water, and after being poured into the mould is allowed to stand a few hours to cool. The colour blocker keeps about three rollers ready, of which one is used for light colours, another for middle tones, and the third solely for black. The rollers are either fixed in a fork with two handles or an axle goes through the wooden pin which is bound in leather at each end wherein the axle revolves in the hollow of the hand.
Fig. 66--Colour roller.
The rollers spread the colour upon a stone of suitable size. The colour should be laid on the rollers--not on the stone--not too thickly, and then evenly distributed on the stone by bringing the roller over it backwards and forwards. Both stone and roller must always be cleaned after use; perfect cleanliness must be carefully observed throughout.
The stone is cleaned with petroleum, the remaining colour is removed from the roller by passing it several times over a sheet of glass, rubbing it down with petroleum before again using it so as to remove any particle of dust adhering.
In order that the colours may appear as bright as possible, a little varnish is added to them, which in every case must be of a kind to suit the particular colour. Dammar varnish is suitable for light colours, and for darker colours amber varnish. Where great brilliancy is required, Venetian turpentine is added; but this lengthens the time required for drying if a little too much is added.
In every case, however, a little siccative must be added to every colour; a few drops materially quicken the drying.
Colour blocking can only be done when the blocks have been secured to the plate, as this must be opened each time it is coloured.
The simplest colour-printing is where one colour appears between the impression in gold, and in this case it is generally done by first making the impression in gold and then in colour.
In more complex work several colours are to be used; at the present time the work is frequently produced requiring colours side by side and superimposed, together with gold, bronze, and aluminium.
The process is in each case as follows: From the block supplied by the engraver an impression is made which forms a matrix. It is best to select a piece of board exactly the size of the covers to be printed and at the two places to be taken by the guide points pieces of vellum are firmly pasted, being already pierced for the guide points, these vellum additions being further secured by pasting over them a strip of paper or cloth. For every block to be used a similar board with its vellum additions is prepared.
Upon the ground of this first matrix the other auxiliary matrices are likewise first impressed with the block--all of them black, of course, so that it would be possible at any time to fit in the blocks.
Every new block for colour printing is pressed into the ground of the auxiliary matrix belonging to it; also for the so-called first-impression block.
It must be understood that colour printing can be done well only upon a perfectly even and smooth surface, therefore it is wise with first-impression blocks, as well as larger colour plates, to repeat the impression, only slightly warm after having given a very hot impression the first time.
Surface papers are an exception as they generally stand very little heat.
It helps here either to let the newly made covers get half dry or, better, to let them lie longer in a damp room.
When different colours are to be superimposed, the order in which they are printed is a matter of some importance. As a rule, the so-called warm tones (yellow, brown, red, or colours containing much of these) are printed first; the cold tones (blue or others containing much blue) being afterwards laid on. White is also classed as a cold tone, but for technical reasons it must nearly always be printed first. If these rules are observed, serious mistakes will seldom be made.
Moreover, proof impressions of the different colours must be taken upon white cardboard, which should be marked for reference, in the same way noting the proportion of the colours used in mixed colours. If the outline block is to be printed in colour, it comes last; gold stamping being done first.
The process of printing in bronze is similar to colour printing, as the bronze is dusted over a preliminary impression in colour (gold upon red or yellow ochre, aluminium upon white, coloured bronze upon a suitable similar colour). Bronze is not printed upon colour, because the bronze sticks too easily to such surfaces in places where it is not wanted; it is then much better to use gold-leaf.
Should it be necessary on the score of economy to make a double working in bronze, the cover must be previously washed with glair.
Leaf metals, pure or alloyed, are printed upon colours after they have been slightly dusted with gilding powder, and with moderate heat. The colours, however, must previously be allowed to dry thoroughly. Larger surfaces are wholly prepared with glair to prevent the gold from adhering where not required.
Most of the colours must cover well where it is not intended that they should have a translucent effect. A good covering is not secured by laying the colour on thickly but by properly mixing the colours, and often also by giving a second coat after the first surface has dried.
Above all, one must avoid too thick and greasy colours. Black must always be printed with a strong good covering colour, as must also the outline block.
For colour printing, the press must be of the same temperature as the room. In winter it is slightly warmed an hour before use, and when necessary this must be repeated later.
There are quite a number of little dodges not easily communicated but which are quickly picked up in practice.
Fig. 67--Stuck-on gauges.
Simple work is not adjusted by pins, but is pushed up to three guides; moreover, the gauge of the press is not generally used, but three little pieces of board are firmly glued to the table instead. The illustration (Fig. 67) will clearly show the arrangement. At the letters A the pieces of board are glued, to which the cover to be blocked is pushed up
Edition notice Project Gutenberg source, credits & licence
The reading text above is the public-domain work. The Project Gutenberg header, production credits and licence are kept here as provenance rather than shown before the book.
Transcriber and production notes
Produced by Chris Curnow, Hazel Batey and the Online Distributed Proofreading Team at http://www.pgdp.net (This file was produced from images generously made available by The Internet Archive)
Front matter as received (title page, contents)
PRACTICAL BOOKBINDING.
Illustration
PRACTICAL BOOKBINDING
BY PAUL ADAM,
_Director of the Duesseldorf Technical School of Artistic and
Practical Bookbinding._
TRANSLATED FROM THE GERMAN BY THOS. E. MAW,
LIBRARIAN KING'S LYNN PUBLIC LIBRARY.
WITH 127 ILLUSTRATIONS.
LONDON SCOTT, GREENWOOD & CO. 19 LUDGATE HILL, E.C.
NEW YORK D. VAN NOSTRAND CO. 23 MURRAY STREET 1903
(_The sole right of translation into English rests with Scott,
Greenwood & Co._)
CONTENTS.
PAGE
METRIC AND BRITISH SYSTEMS COMPARED vi.
PREFACE vii.
Introductory Remarks on Working Methods and Materials 1
_A._--Materials for Sewing and Pasting 1
_B._--Materials for Covering the Book 4
_C._--Materials for Decorating and Finishing 7
_D._--Tools 9
PART I.
FORWARDING.
Chapter I.--General Preparatory Work 13
Chapter II.--Sewing 40
Chapter III.--Forwarding: Cutting, Rounding, and Backing 54
Chapter IV.--Forwarding: Decoration, of Edges and Headbanding 62
Chapter V.--Boarding 85
PART II.
FINISHING.
The Book Cover 93
Chapter VI.--Making the Cover 95
Chapter VII.--Work with the Blocking Press 103
Chapter VIII.--Treatment of Sewn Books, Fastening in Covers,
and Finishing Off 119
Chapter IX.--Hand Finishing 129
Chapter X.--Account Books 157Header as received
The Project Gutenberg eBook of Practical Bookbinding
This eBook is for the use of anyone anywhere in the United States and
most other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg License included with this eBook or online
at www.gutenberg.org. If you are not located in the United States,
you will have to check the laws of the country where you are located
before using this eBook.
Title: Practical Bookbinding
Author: Paul Adam
Translator: Thomas E. Maw
Release date: March 31, 2012 [eBook #39318]
Language: English
Other information and formats: www.gutenberg.org/ebooks/39318
Credits: Produced by Chris Curnow, Hazel Batey and the Online
Distributed Proofreading Team at http://www.pgdp.net (This
file was produced from images generously made available
by The Internet Archive)Full Project Gutenberg licence
Updated editions will replace the previous one—the old editions will
be renamed.
Creating the works from print editions not protected by U.S. copyright
law means that no one owns a United States copyright in these works,
so the Foundation (and you!) can copy and distribute it in the United
States without permission and without paying copyright
royalties. Special rules, set forth in the General Terms of Use part
of this license, apply to copying and distributing Project
Gutenberg™ electronic works to protect the PROJECT GUTENBERG™
concept and trademark. Project Gutenberg is a registered trademark,
and may not be used if you charge for an eBook, except by following
the terms of the trademark license, including paying royalties for use
of the Project Gutenberg trademark. If you do not charge anything for
copies of this eBook, complying with the trademark license is very
easy. You may use this eBook for nearly any purpose such as creation
of derivative works, reports, performances and research. Project
Gutenberg eBooks may be modified and printed and given away—you may
do practically ANYTHING in the United States with eBooks not protected
by U.S. copyright law. Redistribution is subject to the trademark
license, especially commercial redistribution.
START: FULL LICENSE
THE FULL PROJECT GUTENBERG™ LICENSE
PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK
To protect the Project Gutenberg™ mission of promoting the free
distribution of electronic works, by using or distributing this work
(or any other work associated in any way with the phrase “Project
Gutenberg”), you agree to comply with all the terms of the Full
Project Gutenberg License available with this file or online at
www.gutenberg.org/license.
Section 1. General Terms of Use and Redistributing Project Gutenberg
electronic works
1.A. By reading or using any part of this Project Gutenberg
electronic work, you indicate that you have read, understand, agree to
and accept all the terms of this license and intellectual property
(trademark/copyright) agreement. If you do not agree to abide by all
the terms of this agreement, you must cease using and return or
destroy all copies of Project Gutenberg electronic works in your
possession. If you paid a fee for obtaining a copy of or access to a
Project Gutenberg electronic work and you do not agree to be bound
by the terms of this agreement, you may obtain a refund from the person
or entity to whom you paid the fee as set forth in paragraph 1.E.8.
1.B. “Project Gutenberg” is a registered trademark. It may only be
used on or associated in any way with an electronic work by people who
agree to be bound by the terms of this agreement. There are a few
things that you can do with most Project Gutenberg electronic works
even without complying with the full terms of this agreement. See
paragraph 1.C below. There are a lot of things you can do with Project
Gutenberg electronic works if you follow the terms of this
agreement and help preserve free future access to Project Gutenberg
electronic works. See paragraph 1.E below.
1.C. The Project Gutenberg Literary Archive Foundation (“the
Foundation” or PGLAF), owns a compilation copyright in the collection
of Project Gutenberg electronic works. Nearly all the individual
works in the collection are in the public domain in the United
States. If an individual work is unprotected by copyright law in the
United States and you are located in the United States, we do not
claim a right to prevent you from copying, distributing, performing,
displaying or creating derivative works based on the work as long as
all references to Project Gutenberg are removed. Of course, we hope
that you will support the Project Gutenberg mission of promoting
free access to electronic works by freely sharing Project Gutenberg
works in compliance with the terms of this agreement for keeping the
Project Gutenberg name associated with the work. You can easily
comply with the terms of this agreement by keeping this work in the
same format with its attached full Project Gutenberg License when
you share it without charge with others.
1.D. The copyright laws of the place where you are located also govern
what you can do with this work. Copyright laws in most countries are
in a constant state of change. If you are outside the United States,
check the laws of your country in addition to the terms of this
agreement before downloading, copying, displaying, performing,
distributing or creating derivative works based on this work or any
other Project Gutenberg work. The Foundation makes no
representations concerning the copyright status of any work in any
country other than the United States.
1.E. Unless you have removed all references to Project Gutenberg:
1.E.1. The following sentence, with active links to, or other
immediate access to, the full Project Gutenberg License must appear
prominently whenever any copy of a Project Gutenberg work (any work
on which the phrase “Project Gutenberg” appears, or with which the
phrase “Project Gutenberg” is associated) is accessed, displayed,
performed, viewed, copied or distributed:
This eBook is for the use of anyone anywhere in the United States and most
other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg™ License included with this eBook or online
at www.gutenberg.org. If you
are not located in the United States, you will have to check the laws
of the country where you are located before using this eBook.
1.E.2. If an individual Project Gutenberg electronic work is
derived from texts not protected by U.S. copyright law (does not
contain a notice indicating that it is posted with permission of the
copyright holder), the work can be copied and distributed to anyone in
the United States without paying any fees or charges. If you are
redistributing or providing access to a work with the phrase “Project
Gutenberg” associated with or appearing on the work, you must comply
either with the requirements of paragraphs 1.E.1 through 1.E.7 or
obtain permission for the use of the work and the Project Gutenberg
trademark as set forth in paragraphs 1.E.8 or 1.E.9.
1.E.3. If an individual Project Gutenberg electronic work is posted
with the permission of the copyright holder, your use and distribution
must comply with both paragraphs 1.E.1 through 1.E.7 and any
additional terms imposed by the copyright holder. Additional terms
will be linked to the Project Gutenberg License for all works
posted with the permission of the copyright holder found at the
beginning of this work.
1.E.4. Do not unlink or detach or remove the full Project Gutenberg
License terms from this work, or any files containing a part of this
work or any other work associated with Project Gutenberg.
1.E.5. Do not copy, display, perform, distribute or redistribute this
electronic work, or any part of this electronic work, without
prominently displaying the sentence set forth in paragraph 1.E.1 with
active links or immediate access to the full terms of the Project
Gutenberg License.
1.E.6. You may convert to and distribute this work in any binary,
compressed, marked up, nonproprietary or proprietary form, including
any word processing or hypertext form. However, if you provide access
to or distribute copies of a Project Gutenberg work in a format
other than “Plain Vanilla ASCII” or other format used in the official
version posted on the official Project Gutenberg website
(www.gutenberg.org), you must, at no additional cost, fee or expense
to the user, provide a copy, a means of exporting a copy, or a means
of obtaining a copy upon request, of the work in its original “Plain
Vanilla ASCII” or other form. Any alternate format must include the
full Project Gutenberg License as specified in paragraph 1.E.1.
1.E.7. Do not charge a fee for access to, viewing, displaying,
performing, copying or distributing any Project Gutenberg works
unless you comply with paragraph 1.E.8 or 1.E.9.
1.E.8. You may charge a reasonable fee for copies of or providing
access to or distributing Project Gutenberg electronic works
provided that:
• You pay a royalty fee of 20% of the gross profits you derive from
the use of Project Gutenberg works calculated using the method
you already use to calculate your applicable taxes. The fee is owed
to the owner of the Project Gutenberg trademark, but he has
agreed to donate royalties under this paragraph to the Project
Gutenberg Literary Archive Foundation. Royalty payments must be paid
within 60 days following each date on which you prepare (or are
legally required to prepare) your periodic tax returns. Royalty
payments should be clearly marked as such and sent to the Project
Gutenberg Literary Archive Foundation at the address specified in
Section 4, “Information about donations to the Project Gutenberg
Literary Archive Foundation.”
• You provide a full refund of any money paid by a user who notifies
you in writing (or by e-mail) within 30 days of receipt that s/he
does not agree to the terms of the full Project Gutenberg™
License. You must require such a user to return or destroy all
copies of the works possessed in a physical medium and discontinue
all use of and all access to other copies of Project Gutenberg™
works.
• You provide, in accordance with paragraph 1.F.3, a full refund of
any money paid for a work or a replacement copy, if a defect in the
electronic work is discovered and reported to you within 90 days of
receipt of the work.
• You comply with all other terms of this agreement for free
distribution of Project Gutenberg™ works.
1.E.9. If you wish to charge a fee or distribute a Project
Gutenberg™ electronic work or group of works on different terms than
are set forth in this agreement, you must obtain permission in writing
from the Project Gutenberg Literary Archive Foundation, the manager of
the Project Gutenberg™ trademark. Contact the Foundation as set
forth in Section 3 below.
1.F.
1.F.1. Project Gutenberg volunteers and employees expend considerable
effort to identify, do copyright research on, transcribe and proofread
works not protected by U.S. copyright law in creating the Project
Gutenberg™ collection. Despite these efforts, Project Gutenberg™
electronic works, and the medium on which they may be stored, may
contain “Defects,” such as, but not limited to, incomplete, inaccurate
or corrupt data, transcription errors, a copyright or other
intellectual property infringement, a defective or damaged disk or
other medium, a computer virus, or computer codes that damage or
cannot be read by your equipment.
1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right
of Replacement or Refund” described in paragraph 1.F.3, the Project
Gutenberg Literary Archive Foundation, the owner of the Project
Gutenberg™ trademark, and any other party distributing a Project
Gutenberg™ electronic work under this agreement, disclaim all
liability to you for damages, costs and expenses, including legal
fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGE.
1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
defect in this electronic work within 90 days of receiving it, you can
receive a refund of the money (if any) you paid for it by sending a
written explanation to the person you received the work from. If you
received the work on a physical medium, you must return the medium
with your written explanation. The person or entity that provided you
with the defective work may elect to provide a replacement copy in
lieu of a refund. If you received the work electronically, the person
or entity providing it to you may choose to give you a second
opportunity to receive the work electronically in lieu of a refund. If
the second copy is also defective, you may demand a refund in writing
without further opportunities to fix the problem.
1.F.4. Except for the limited right of replacement or refund set forth
in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO
OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
1.F.5. Some states do not allow disclaimers of certain implied
warranties or the exclusion or limitation of certain types of
damages. If any disclaimer or limitation set forth in this agreement
violates the law of the state applicable to this agreement, the
agreement shall be interpreted to make the maximum disclaimer or
limitation permitted by the applicable state law. The invalidity or
unenforceability of any provision of this agreement shall not void the
remaining provisions.
1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
trademark owner, any agent or employee of the Foundation, anyone
providing copies of Project Gutenberg™ electronic works in
accordance with this agreement, and any volunteers associated with the
production, promotion and distribution of Project Gutenberg™
electronic works, harmless from all liability, costs and expenses,
including legal fees, that arise directly or indirectly from any of
the following which you do or cause to occur: (a) distribution of this
or any Project Gutenberg work, (b) alteration, modification, or
additions or deletions to any Project Gutenberg work, and (c) any
Defect you cause.
Section 2. Information about the Mission of Project Gutenberg
Project Gutenberg is synonymous with the free distribution of
electronic works in formats readable by the widest variety of
computers including obsolete, old, middle-aged and new computers. It
exists because of the efforts of hundreds of volunteers and donations
from people in all walks of life.
Volunteers and financial support to provide volunteers with the
assistance they need are critical to reaching Project Gutenberg’s
goals and ensuring that the Project Gutenberg collection will
remain freely available for generations to come. In 2001, the Project
Gutenberg Literary Archive Foundation was created to provide a secure
and permanent future for Project Gutenberg and future
generations. To learn more about the Project Gutenberg Literary
Archive Foundation and how your efforts and donations can help, see
Sections 3 and 4 and the Foundation information page at www.gutenberg.org.
Section 3. Information about the Project Gutenberg Literary Archive Foundation
The Project Gutenberg Literary Archive Foundation is a non-profit
501(c)(3) educational corporation organized under the laws of the
state of Mississippi and granted tax exempt status by the Internal
Revenue Service. The Foundation’s EIN or federal tax identification
number is 64-6221541. Contributions to the Project Gutenberg Literary
Archive Foundation are tax deductible to the full extent permitted by
U.S. federal laws and your state’s laws.
The Foundation’s business office is located at 41 Watchung Plaza #516,
Montclair NJ 07042, USA, +1 (862) 621-9288. Email contact links and up
to date contact information can be found at the Foundation’s website
and official page at www.gutenberg.org/contact
Section 4. Information about Donations to the Project Gutenberg
Literary Archive Foundation
Project Gutenberg™ depends upon and cannot survive without widespread
public support and donations to carry out its mission of
increasing the number of public domain and licensed works that can be
freely distributed in machine-readable form accessible by the widest
array of equipment including outdated equipment. Many small donations
($1 to $5,000) are particularly important to maintaining tax exempt
status with the IRS.
The Foundation is committed to complying with the laws regulating
charities and charitable donations in all 50 states of the United
States. Compliance requirements are not uniform and it takes a
considerable effort, much paperwork and many fees to meet and keep up
with these requirements. We do not solicit donations in locations
where we have not received written confirmation of compliance. To SEND
DONATIONS or determine the status of compliance for any particular state
visit www.gutenberg.org/donate.
While we cannot and do not solicit contributions from states where we
have not met the solicitation requirements, we know of no prohibition
against accepting unsolicited donations from donors in such states who
approach us with offers to donate.
International donations are gratefully accepted, but we cannot make
any statements concerning tax treatment of donations received from
outside the United States. U.S. laws alone swamp our small staff.
Please check the Project Gutenberg web pages for current donation
methods and addresses. Donations are accepted in a number of other
ways including checks, online payments and credit card donations. To
donate, please visit: www.gutenberg.org/donate.
Section 5. General Information About Project Gutenberg electronic works
Professor Michael S. Hart was the originator of the Project
Gutenberg concept of a library of electronic works that could be
freely shared with anyone. For forty years, he produced and
distributed Project Gutenberg eBooks with only a loose network of
volunteer support.
Project Gutenberg eBooks are often created from several printed
editions, all of which are confirmed as not protected by copyright in
the U.S. unless a copyright notice is included. Thus, we do not
necessarily keep eBooks in compliance with any particular paper
edition.
Most people start at our website which has the main PG search
facility: www.gutenberg.org.
This website includes information about Project Gutenberg,
including how to make donations to the Project Gutenberg Literary
Archive Foundation, how to help produce our new eBooks, and how to
subscribe to our email newsletter to hear about new eBooks.Source: Project Gutenberg ebook #39318. Public-domain status is recorded per item; the licence text above is reproduced unchanged.