
Gutenberg · ebook 38387
Library Bookbinding
by Arthur Low Bailey · English · public domain in the US
Library Bookbinding by Arthur Low Bailey is an English public-domain text held from Project Gutenberg (ebook #38387). _Librarian Wilmington_ (_Delaware_) _Institute Free Library_
PREFACE
It has been the purpose of the writer in these chapters on library bookbinding to set forth as clearly as possible the best information relating to processes, materials, routine and various other lesser matters pertaining to bookbinding which must be taken into consideration by librarians, or by assistants in charge of binding departments.
Although much of this information exists elsewhere in printed form, it is scattered through various books and articles. In some respects, therefore, this book is a gathering together of scattered material. It is hoped, however, that there is enough new material to make the book of interest to those who deal daily with binding problems, and that the book as a whole may help to solve some of the questions relating to binding in libraries both large and small.
Most books on binding and all books on library binding have devoted some space to paper, its composition, manufacture, finish and use. As the subject is so fully dealt with elsewhere it has not been included here.
Those who are interested will find full information in the technical books on paper, in Mr. Dana's "Notes on book binding for libraries," and in Messrs. Coutts and Stephen's "Manual of library binding." There is also an excellent article on wood pulp paper in the Scientific American of October 4, 1913.
Nor has it seemed desirable to include chapters on commercial binding nor on historical bindings. Both of these subjects are treated adequately in Coutts and Stephen's "Manual." The present writer has limited his discussion to matters dealing directly with the binding of books for libraries.
In one or two cases the same subject has been treated in two different chapters because the subject matter belonged in both places, and in neither case would the discussion be complete without it.
A. L. B.
December 9, 1915.
TABLE OF CONTENTS
Chapter I. Introduction 3
II. Selection of a binder 9
III. Processes 13
IV. Materials 51
V. Specifications 87
VI. Binding before purchase and reinforcing 103
VII. Cost 115
VIII. Preparing for the bindery 125
IX. Binding records and routine 149
X. Repairing, recasing, recovering etc. 165
XI. Magazine binders 199
XII. Pamphlets 205
XIII. Bindery in the library building 209
Appendix A. Specifications of the U. S. Bureau
of Standards for book cloths 217
B. Reading list on binding 221
C. List of technical terms 225
Index 245
LIBRARY BOOKBINDING
LIBRARY BOOKBINDING
CHAPTER I
INTRODUCTION
An examination of the annual reports of libraries in the United States shows that from four to eight per cent of the total income is spent for binding; the amounts ranging from $2,000 to over $40,000 a year for this one item. It must be admitted that these are large sums and that a knowledge of binding materials and processes is necessary in order to spend this money wisely. In many libraries the appropriation for books includes binding and periodicals. It is evident, therefore, that every dollar saved on binding can be devoted to the purchase of books. And what librarian does not desire more money for new books?
In spite of the importance of the subject a great deal of ignorance has prevailed in years past, and far too many librarians of the present day fail to realize that here is one place where money can be easily wasted.
Possibly one reason for the ignorance about binding is that, except in a minor degree, it does not directly affect the public, for librarians are quick to make changes which will increase the interest of the public in the library. Another reason is that experiments are necessary; and since it takes time to draw conclusions from experiments, definite rules have not been formulated.
In fact, experiments are still being tried. But while in the past they were along the line of making books stronger, the experiments of the present are rather along the line of adapting different methods to different books, according to the paper on which they are printed, or according to the kind of use they will receive. It is reasonably safe to say that present methods of the best library binders make a book as strong as it is possible to make it. Progress no longer lies along the line of strength.
In order to administer a binding department wisely, the librarian or assistant in charge of binding must know materials, processes, and books; and especially must he know how books should be bound to meet the use they are to receive.
For example, fiction that is very popular should be bound differently from fiction which must be kept on the shelves, but which is not popular; it is easily apparent that McCutcheon's "Graustark" should be bound differently from Henry James' "Golden bowl." Heavy reference books constantly consulted should be bound differently from reference books used only occasionally, while it may be wise to bind magazines differently from either. A librarian of a reference library will adopt methods differing from those which are used in public libraries.
A good working knowledge of materials and processes can be easily obtained. The saving of expense comes in applying them to use.
A recent advertisement of a binder stated that his books were rebound more times than the books of any other binder. This statement is a sad commentary on the serviceability of his books and calls to mind a practice of twenty years ago which is too prevalent even at the present time. At that time it was the recognized custom to bind as cheaply as possible books which circulated rapidly and wore out quickly.
Those who favor this custom fail to realize that in the case of books which are constantly used the actual cost of binding does not depend on the initial cost per volume, but on the ratio of cost to circulation. This is a point first brought out by Mr. J. C. Dana in his "Notes on bookbinding for libraries," and one on which it is impossible to lay too much emphasis.
A book which costs 35c. to bind and which circulates 35 times has cost one cent for each time it has been issued after rebinding; while a book which has cost 50c. to bind and has been issued 100 times (a fair average for a 50c. binding) costs one half cent for each time it has been issued. Obviously the 50c. binding is much cheaper.
It is probable that the 35c. book must either be rebound at an additional expense of 35c. or else a new copy must be purchased at a cost of $1, while the 50c. binding may carry the book to a point where it can be discarded absolutely. Certainly it should never be rebound again. It is important, therefore, that the librarian who does not know what his binding is costing per issue should keep statistics of circulation for a sufficient length of time to obtain general averages which will be fairly accurate.
While a very strong binding is necessary for fiction and juvenile books in public libraries, it is probable that on many books of a serious character some of the strengthening processes which must be used on fiction and juveniles may be omitted. It should be noted that while this is true of public libraries, the reverse would probably be true in college and reference libraries where a much larger proportion of serious books should be bound as strongly as possible.
There are three general kinds of binding:
(a) Commercial, or edition binding.
(b) Artistic binding.
(c) Library binding.
Commercial binding is that in which practically all books come from the publishers. For the most part it is the product of machinery from beginning to end, and the material used is generally poor. Apparently the sole object in view of most publishers is to turn out a book that will attract the eye. Strength is not an element for which they strive.
From their point of view they cannot be severely blamed for making strength a secondary consideration. By far the largest part of their product is sold to individuals, and the strength of the binding is adequate for the amount of use that these books will receive. From the library point of view, however, publishers' bindings are entirely inadequate. One cannot expect, of course, that the publisher will put a popular novel into a binding strong enough to meet the demands of library use. On the other hand, one cannot blame librarians for being exasperated when heavy books of travel, history, or biography part from their covers when they have been in the hands of less than ten readers.
The distinguishing characteristics of commercial binding, and at the same time its greatest weaknesses, are the machine sewing and the insecure way in which the book is fastened into the cover. Very little extra expense either in material, care, or workmanship, would make most books outside of fiction sufficiently strong to withstand all the wear that they will receive. Unfortunately the publishers fail to realize this, and books by the thousands come from the binderies covered on the back with the coarsest kind of super which does not even extend to the head or tail of the book.
A stouter cloth, carefully applied, running the entire length of the back would cost very little more per volume, but would strengthen it materially.
While practically all commercial binding is lacking in strength, this is due almost wholly to trade conditions, for commercial binding can be made exceedingly strong. One has only to turn to the 1912 edition of the Century Dictionary or to the United States Catalog, which are practically machine bound throughout, to realize this fact. However, until librarians are united in their demands for stronger bindings, we can expect to see the present poor work turned out in as large quantities as ever.
There is another kind of binding which is, if possible, even more unsuitable for libraries. This is artistic binding which is done exclusively for individuals, beauty of appearance being the chief object in view. It differs from commercial binding in being all hand work instead of machine work. Since hand work is used and the main object in view is beauty, it follows, of course, that such books are much stronger than those bound by publishers.
But the strength of these books is in many cases not proof against the wear that they would receive in libraries. No special methods of sewing or strengthening the first and last sections are used. Practically all artistic books are bound in leather and frequently in full leather. Whenever the leather used is anything other than good morocco, it is an element of weakness rather than strength. In addition to these objections, artistic bindings are usually so expensive as to be beyond the reach of any library.
In library binding the main consideration is strength. Not only is beauty a secondary consideration, it is scarcely taken into consideration at all. For it must be confessed that library bindings are seldom attractive. No library can afford to pay for ornamentation of backs and sides of books. Library binding is all hand work. Although machine binding can be made exceedingly strong, machines cannot be used on library binding, because the books vary so much in size and lettering. The main reason why commercial binding can be done by machinery is because a large number of books are bound exactly alike.
In library binding it seldom happens that more than two volumes, the same in size and lettering, are bound at the same time. Library binding also differs from other bindings in that the use the book is to receive is made the basis of selection of materials and methods.
CHAPTER II
SELECTION OF A BINDER
Since library binding differs widely from other kinds of binding, it follows naturally that it is best to have this work done by men who understand its special requirements. Unfortunately, there are comparatively few binders who make a specialty of this kind of work.
Librarians of most of the smaller libraries are forced by local prejudice to give their work to the local binder or to the nearest outside binder in order to save the expense of transportation. If the work is sent to the local binder, it must be sent to one who is doing other kinds of binding and to whom the library work is, in a way, a minor consideration. He would object if the work were sent out of town, but the total amount of the library work is small compared with his other work.
Such binders usually have one way for binding all books (except those which come under the head of blank-book work) and the library books go through the regular process of being sewed on twine and put into covers with no special reinforcements. The materials used are not the best and the workmanship is generally poor. Local binders, realizing that the funds are usually inadequate for the needs of the library, frequently do this work at a price which at first sight seems cheap.
When, however, the poor service which the bindings give is taken into consideration the price is really very high. Many of these binders have been in business for years; and although they may be good workmen and do honest work, they are very sure that they know more about binding than any librarian, and it is with difficulty that they can be prevailed upon to adopt suggestions.
It is only fair, of course, that a library which is supported either in whole or in part by public funds should, when possible, have its work done by residents of the town. For this reason, therefore, the librarian should learn in just what ways good library binding differs from other binding. All the good materials and processes, and all the various methods of strengthening a book should be studied carefully so that the binder can be told exactly how the work should be done. The binder will probably rebel, but perhaps he can be converted and the effort is worth while.
If the binder fails to grasp the ideas of the librarian, or refuses to carry them out, the work should be sent out of town to a good binder, for deference to local prejudice does not require that the efficiency of the library be impaired. When work is sent out of town the librarian is somewhat at a disadvantage, for no examination of the work can be made while the books are in process. That the binder chosen should do honest work goes without saying. The work of a dishonest or incompetent binder always shows in the poor service which the books give, but inasmuch as dishonest work is generally covered up, it takes time to discover it.
Therefore, great care must be taken to select a good binder in the first place. Librarians who are in doubt should consult the librarians of large libraries, or apply to the Binding committee of the American Library Association for the names of reliable binders.
While librarians should be able to give suggestions to binders who are not accustomed to library binding, and failing that should exercise good judgment in selecting a binder at a distance, they should not expect the impossible. The writer has seen books sent to binders which were in such bad condition that no binder could bind them satisfactorily. Some librarians expect too much of a binder; others do not realize that they are not demanding all that they should receive.
Having selected a competent binder the librarian should not insist that unimportant details be done according to his own ideas. If the binder understands that he may have the work only so long as he follows the specifications faithfully, one may safely leave the details to him.
It should further be borne in mind that good binding is seldom obtained at low prices. A library book well bound requires good material, good workmanship and special reinforcements which take time. Since the largest part of the cost of a book is due to the labor spent on it, it follows that low prices can prevail only in those localities where the cost of labor is below the standard.
Since workmanship has as much to do with good binding as specifications it is not wise to submit specifications to different binders for bids.
It is better to ask binders to submit samples of their work with specifications of the way in which the books are bound. If, however, it seems wise to ask for bids, it is far from wise to choose the lowest bidder unless absolutely assured that the workmanship and material will be satisfactory.
CHAPTER III
PROCESSES
The processes of bookbinding have been so fully covered in the books of Messrs. Cockerell, Zaehnsdorf, Crane, and others, that the need of further material of a similar character is not readily apparent. The only excuse the writer has to offer for discussing the matter of processes at any length is that there seems to exist nowhere any description of the processes that are used in the best library binderies. Mr. Dana in his "Notes on bookbinding for libraries" touches only certain points of the processes here and there. Mr.
Stephen in Coutts and Stephen's "Manual of library binding" has a chapter on hand bookbinding, but confines himself closely to the general processes that have been in vogue for years; the modifications used in library binding are not touched upon. In other words the works of Cockerell, Zaehnsdorf, Crane and others are too full, while descriptions in books devoted to library binding are not full enough.
It is the purpose of this chapter to cover somewhat in detail the main processes as they are carried out in the best library binderies.
Explanations of the technical terms used will be found in the list of technical terms at the end of the book.
Without discussing the composition of paper it is necessary to state that the paper of a book has a very important effect upon its binding.
Its thickness, tensile strength, firmness, toughness, strength after being sawed or perforated for sewing, and strength after folding, all have an effect on its durability. Especial emphasis must be laid upon strength after folding, for it must be remembered that it is through the fold that the book is sewed. If a crease or a fold in a piece of paper weakens that piece of paper, it will be impossible to make a strong book by sewing in the ordinary way. If a fold has very little effect upon the strength of the paper ordinary sewing may be satisfactory. The folding of paper in 95 per cent of fiction and juvenile books weakens it at the fold over 50 per cent.
In a good piece of paper the fold weakens it not over 5 per cent.
The problem of paper is a modern one, due to the use of wood pulp and other short-fibred materials in paper manufacture. All binders complain bitterly of the impossibility of binding it properly. The librarian, however, should know the way in which it can be bound to give the maximum amount of service and should not allow a binder to blame the paper for faults which are due to his ignorance or to poor workmanship.
While the customs of library binders vary somewhat according to the prejudices of the different men, the following description covers the binding processes carried out at most binderies.
1. TAKING APART
After the books have been checked with the statement of the librarian to see that the correct number has been received, each one is taken apart carefully and all old threads, glue, paste, etc., removed from the back.
If the book is in a regular machine sewed publisher's cover it will be comparatively easy to remove old threads and glue from the back. If in an old hand sewed one, it may be a little more difficult.
The book is first removed from the cover. The first signature is then turned back and threads cut with a sharp knife. Generally this will loosen the signature so that it can be separated easily from the rest of the volume. If it is still held by glue and there is danger of injuring the back of the signature, a bone folder is used. If the book had a tight back and the leather, back-lining paper and glue form a very firm back not easily separated in the manner described, the glue may be softened with paste or warm water, with care necessary to prevent the dampness from penetrating the book.
2. COLLATION
The book should then be collated. The best library binders make themselves responsible for page collation but they do not bother to see that all plates, illustrations, maps, etc., which may be called for by the table of contents, are in proper place. In the case of periodicals they do not always discover the fact that certain parts, not included in the main paging, are missing. Their collation is that of main paging only. Periodicals must, therefore, have title page, table of contents and index in their proper places. Books with two or more main pagings or many unpaged illustrations must be collated at the library. (See Preparing for the bindery, p. 125.)
3. KNOCKING DOWN
(a) Backs of signatures are then pounded down so that they may be as nearly as possible the same thickness as the front of the signatures.
Care must be taken to have a clean hammer and to let it fall evenly on the paper. If the backs are not properly pounded down there is likely to be too much swell in the back of the book when it is finally sewed. In all the first processes of binding the question of undue swelling of the back must be taken into consideration.
(b) If the book must be overcast when it comes to be sewed, the back is not only pounded down at this stage, but it is also put under the knife and entirely cut off, leaving single leaves instead of folded sections. If it is not pounded it cannot be cut properly. The success of overcasting depends largely on the amount of margin at the back, so that care must be taken not to cut more than is absolutely necessary.
4. MENDING
Leaves are mended with thin tough paper. The librarian should not, however, expect binders to mend books which have a large number of torn leaves without making an extra charge.
5. GLUING
Books which are to be overcast and which have had the backs cut off are slightly glued to hold the leaves together. A sufficient number can then be taken off and handled as a section without coming apart.
6. FLY LEAVES GUARDED
Fly-leaves, made of kraft or manila paper running about 60 pounds to the ream, which have previously been guarded with cloth are added to the book. In guarding, a strip of cloth is pasted around the back of the folded fly-leaf covering about one quarter of an inch on each side. When the book is sewed the needle passes through the cloth as well as the paper. Different binders use different materials for guarding fly-leaves, end papers and signatures. It must, however, be a cloth of close weave, strong, and light in weight. The English cloth called jaconet, used by some binders, is probably as satisfactory as any.
This is one part of library binding which differs radically from the custom in ordinary hand work. Old-fashioned binders, unless properly instructed, will simply fold a piece of paper, and tip it on to the first and last signatures with paste, thus forming an element of weakness instead of strength. When the fly-leaves are guarded and properly sewed they become an integral part of the book and no tipping is necessary.
7. SECTIONS GUARDED
At this point it is also necessary to guard the first and last signatures of books which are to be sewed in the regular way. Overcast books do not need such guards.
Guarding of first and last signatures is another of the distinctive features of library binding. In the case of books bound in the regular fashion the sewing invariably first gives way at the first and last signatures. Guarding with jaconet prevents the threads which lie in the middle of the signatures from pulling through the paper. This method is essential if it is supposed that the book will be much used. It is not essential for books which will be used only occasionally.
8. ILLUSTRATIONS GUARDED
Illustrations are guarded with a thin, tough paper, not with cloth. The guard folds around an adjoining signature and is sewed through.
9. SAWING
If the book is not to be overcast, it is screwed tightly into the backing-press and sawed to make the grooves in which the bands or twines are laid when the book is sewed. Grooves for three bands must be made for books eight inches high, four for twelve-inch books and five for fifteen-inch books. For fiction two bands are used. There must also be two additional grooves, much shallower than the others, about one half inch from the head and tail of the book for the kettlestitch.
After the grooves for kettlestitch have been sawed the two grooves for bands will divide the rest of the back into three equal parts. For fine work it is necessary to measure the book carefully and mark with a pencil; but in most library work measurement by the eye alone is sufficient. In sawing, care must be taken not to saw too deeply, since too deep a cut allows the signature to play back and forth and is plainly visible inside.
There are some good library binders who overcast books in the modern way, and yet who sew on bands. Such binders will at this point saw all books. There are also some good library binders who use no bands when overcasting and who sew all other books on tapes. These binders omit sawing.
10. END PAPERS ADDED
At this point it is best to add end papers. These are always guarded on the outside of the fold and sometimes on the inside. They should be made of good, strong paper somewhat heavier than that used for fly-leaves.
Some binders have special papers made to order with a design which serves as a trade mark. End papers, in the same way as fly-leaves, are prepared with guards in quantity and simply need to be trimmed to the size of the book. They are not added at the same time as fly-leaves because they must not be sawed. If this is done the holes show through after the end paper is pasted down.
11. SEWING
Regular or Bench Sewing. When the signatures are ready for sewing, twines (or "bands" as they are commonly called) are stretched taut on the sewing bench and adjusted so that they will fit into the saw-cuts in signatures. (Fig. 1.)
FIGURE 1.--Sewing bench showing bands adjusted.
FIGURE 2.--Sewing on sunken cords. Based on illustration in Report of the Committee on Bookbinding. Edited for Society of Arts, London, 1905.
The book is placed back of the sewing bench with the fore-edge toward the sewer and with the first section on top. The first section (i. e. the end paper) to be sewed is then turned over, opened in the middle by the left hand, and placed on the sewing bench.
The sewer, as she faces toward the right, with the right hand passes the needle from the outside through the sawcut for the kettlestitch, where it is taken by the left hand along the inside of the section and passed out on the near side of the first band, then in again on the far side of the first band, along the inside of the section to the second band, where the process is repeated; and so on, bringing the needle out in the far kettlestitch. (Fig.
2.) The thread is pulled tight at each stitch and about two inches of thread is allowed to hang from the first kettlestitch. In some few cases it may be advisable to bring the needle out on the far side of the band and in again on the near side, thus entirely encircling the band with the thread. The next section (i. e. the fly-leaves) is then laid on and the process repeated, except that the sewing proceeds from the far end to the near end.
When the thread is brought out of the kettle stitch of the second section the end of the thread left projecting from the first section is securely tied to it, and the sewer proceeds with the third section. This will be the first signature of the book. On reaching the last sawcut at the far end in the third section the needle is put between the second and first sections carrying the thread down in such a way as to form a buttonhole stitch. (Fig. 3.)
FIGURE 3.--Kettle stitch.
All other signatures are sewed in the same way, the last section sewed being securely fastened to the others. It is possible to sew a number of books one after another without removing them from the sewing-bench. If the back swells unduly the sections can be pounded down with a piece of wood, care being taken not to drive them inward. The sewing should be neither too loose nor too tight. If too loose a firm, compact book cannot be made; if too tight the threads may break in the process of backing. Bands are allowed to project about an inch on each side of the book.
Formerly it was the practice of some binders to sew in a way technically called "two-on." This simply means that the sewer when reaching the middle of the signature, passes the needle into the corresponding sawcut of the signature above and sews through to the other end. This always leaves an end of a signature unsewed. This way of sewing is permissible on books which have a large number of thin signatures, in order to prevent the thread from unduly swelling the back. It is never permissible on other books.
The foregoing account gives a very brief description of ordinary sewing.
It is easily understood when once seen. Librarians who have charge of binding should keep the process thoroughly in mind for it is the most important single process in the making of a book. Such sewing will be used on a large number of books which have to be rebound, but a still larger number, practically all fiction and juvenile books, should be sewed in a different manner; that is, with some kind of an overcast stitch.
Overcasting. The modern overcasting stitch resembles in principle the old-fashioned whipstitching, but differs radically in actual performance. It is exceedingly strong, while the old-fashioned whipstitching is not. It has been objected that modern overcasting takes away much of the flexibility of a book and that books once sewed in this way can never be rebound. It is true that an oversewed book is not as flexible as one sewed through the signatures, yet most of them are more flexible than one might suppose. It is also true that the book can never be rebound, but if the overcasting is properly done, the sewing will last until the book is discarded.
It is for this reason that it is used on practically all fiction and juvenile books.
According to the old-fashioned method of whipstitching it was the custom to cut off the backs of signatures, glue them slightly, take a few leaves and sew them over and over making five or six stitches to a section, as shown in Figure 4. The next section was then sewed in the same way, but it was not joined in any way to the section beneath except by the kettlestitch and occasionally by a little paste. When sewed in this way the leaves inside of each arbitrary section would open only as far back as the threads of the stitches, while between the sections the book would open to the back of the section. If paste had been used the strain of opening tended to pull the leaves apart.
If the book was subjected to hard wear the thread cut into the paper.
FIGURE 4.--Old-fashioned whipstitching. Each section is sewed separately.
Today every progressive library binder has a special method of overcasting and each claims that his method is the best. Librarians, however, can see many points of resemblance between them, and few points of difference. In actual wearing qualities the sewing of one seems as good as that of another. When properly done the sewing prescribed by all of the methods is still in good condition when the books have to be withdrawn from circulation.
In overcasting, as in old-fashioned whipstitching, the sewer selects a certain number of sheets for sewing. Bands are placed on the sewing-bench as in regular sewing, though some binders claim that it is not necessary to sew either on bands or tapes. The sections are first perforated by a machine to facilitate the work of the sewer and to insure that all stitches shall be equidistant from the back of the book.
So far as is known no machine for this purpose is on the market. It is certain, however, that the best binders have machines for this purpose.
They have either designed their own machines or have adapted those made for other purposes. If the book is printed on thick, spongy paper it will increase flexibility if the paper is creased along the line of perforation.
FIGURE 5.--One kind of modern overcast stitch. There are others equally good. Note that each stitch extends through two sections.
It is difficult to give a description of modern overcasting which can be easily understood by one unfamiliar with sewing processes. The reader will be helped by looking closely at Figure 5 while reading the following description, but one can understand it best by seeing it done or by tearing a book apart and examining the sewing.
The first section of the book is sewed over and over in the same way as in the old-fashioned method of whipstitching, except that a great many more stitches are taken. The second section, when placed on the first, is also sewed over and over but a certain number of stitches are also made which connect the second section with the first. In the same way the third section is sewed to the second and so on through the book, so that when the book is finally sewed it is tight and compact; its weakness lies in the paper itself, not in the sewing.
Some binders add three kettlestitches at the end of the book instead of one, believing that when all kettlestitches are placed in one sawcut the swell at the head and tail of the book is too great.
FIGURE 6.--From "About Public Library Books and Their Binding" by Cedric Chivers.
FIGURE 7.--Sewing on tapes. Sawcuts made only for kettle stitches. Based on illustration in Report of the Committee on Leather for Bookbinding.
Edited for Society of Arts, London, 1905.
Overcasting is the most expensive way of sewing a book, so that it is advantageous to binders to place as large a number of leaves as possible in a section. The more careful binders, however, regulate the number of leaves in a section according to the kind of paper in the book. A larger number of leaves can be taken in books printed on thin paper than in those printed on thick, spongy or heavy papers.
FIGURE 8.--Stitching.
In deciding how a book ought to be sewed one must consider: (a) The use the book is to receive. If it will not receive hard usage sew through the signatures; otherwise overcast. (b) Paper on which the book is printed. Poor paper should be oversewed. (Fig. 6.)
Tapes. When it does not seem necessary to overcast it may be advantageous to sew on tapes instead of bands. This method eliminates saw-cuts since the narrow tapes are simply laid against the back of the book and the needle passed around them, as indicated in Figure 7. Sewing on tapes makes a book much more flexible than it can be made any other way except by sewing on raised bands. Music should always be sewed in this way. Until recently it was supposed that tapes added strength, but it is certain that they do not if the book is properly bound in other respects. If used at all, tapes should be narrow.
Wide ones take up a great deal of surface and when glue is applied this surface remains untouched, unless the sewer has sewed through them instead of around them.
Stitching. Stitching is the process of sewing loose leaves lengthwise on a sewing machine, after which the stitched sections are sewed in the regular way on bands. (Fig. 8.) The objection made to old-fashioned whipstitching, that between the sections the book opens all the way to the back while inside the section it opens only as far as the threads, is equally applicable to a stitched book. Any one who has read a book sewed in this way will remember how difficult it was to hold in the hands. Stitching makes a stronger book than the old-fashioned whipstitching but cannot compare in strength with the modern overcasting.
In some few cases it may be used advantageously on the first and last signatures of a book, but its use on the entire book cannot be too strongly condemned.
It may be inferred by what has been said about sewing that it is a comparatively simple matter to sew books properly. It is right at this point, however, that the librarian and the binder who does not understand the requirements of library work will come into conflict. The binder will insist that all books must be sewed on bands. When the backs of sections are very badly worn he will agree to whipstitch, but will use the old method. The librarian will insist not only that nine-tenths of fiction and juvenile books must be overcast, but that a special kind of overcasting must be used. The binders who make a specialty of library work do all this as a matter of course.
At least one binder tests the thickness, tensile strength and other qualities of the paper and sews each book in the way that experience has shown to be the best.
FORWARDING
After the book is sewed it goes to the forwarder who has charge of the book during all processes which the book passes through between sewing and finishing. Forwarding includes trimming, gluing, rounding, backing, putting on back-lining, making the case (or lacing-in, see page 42), casing-in, pressing.
12. FLY LEAVES PASTED
The end papers and fly-leaves which lie together are pasted together, making one thick fly-leaf. When it is remembered that both end papers and fly-leaves are guarded with cloth, it will be seen that pasting the two together adds materially to the strength of the book.
13. BANDS FRAYED
The bands which project about an inch and a half on each side of the book are frayed out at the end and pasted to the end papers. The fraying is done so that they will paste down flat, and the pasting so that they will be out of the way during succeeding processes.
14. TRIMMING
The book is squared up by tapping on a flat surface, and trimmed at the head, fore-edge and tail. As little as possible must be trimmed, but binders find that if less than an eighth of an inch is cut the cutting machine does not work well. Trimming makes the edges even and what is more important in rebound books, removes much dirt.
15. SPRINKLING
At this point edges are sprinkled. This process is not essential either for strength or beauty, but it helps to keep the book from becoming soiled, or at least from showing dirt. It cannot be expected on cheap work. The process was formerly done by hand, using a brush and shaking the coloring matter on the book. It can now be done with a machine operated by hand which sprays the coloring matter on the book.
Occasionally the top of the book is burnished with an agate or blood stone.
Occasionally also it may be desirable to gild the top of a book which is being rebound. When this occurs it is not a process to which the librarian need give much attention, except to be sure that good gold is used.
16. GLUING
The back of the book is then slightly glued. The glue must be very hot and quite thin, and must be thoroughly worked into the back. By placing books in a pile a number can be done at a time.
17. ROUNDING
As soon as the glue has stiffened but before it is hard the book is rounded. This must be done by experts and is a process which must be seen to be understood. The book is placed on the table with the fore edge toward the workman who then hammers the part of the back lying uppermost in such a way as to force the upper part of the book toward the workman. The book is then turned over and the process repeated.
After a few operations like this the back of the book becomes rounded and the fore edge concave.
18. BACKING
The book is then placed in a backing press allowing about an eighth of an inch to project, and screwed very tight. With a backing hammer the rounding process is continued and the sides of the book forced down over the edge of the press to form a projection against which the edge of the board for the side rests, forming the joint. In hammering, the workman begins at the proper distance from the center of the back so that he can force the backs of the other signatures over on each side toward the edge. (Fig. 9.)
FIGURE 9.--A book rounded and backed.
This process is the most important one in forwarding, calling for skilled labor. If the hammer is not used in exactly the right way the backs of the signatures may be crushed in, the stitches broken, or the paper or bands cut. In any case the book is materially weakened. A good workman will make a sharp joint and round the book perfectly without injuring its strength in any way.
19. BACK LINING
All books have a lining of one kind or another on the back.
Machine-bound books are generally lined with a coarse "super," as it is called in this country, or "mull" as it is called in England. Some library binders use a thin muslin, but the best material is canton flannel cut in strips wide enough to cover the back of the book and also to project about one inch on each side. The back of the book is glued, while the nap or fuzzy side of the canton flannel is pasted and then put on the back and well rubbed down. It is very important that both the glue and the paste be used. Experience has proved that when only one is used the canton flannel will come off, but when both are used, it becomes an integral part of the book.
The flannel which projects on the sides must be pasted to the end papers. When the paste and the glue have dried, the canton flannel shrinks tight to the back and adds materially to the strength of the book. After drying the flannel is trimmed at the head and tail close to the back.
If the book is a valuable one that will receive hard usage and therefore should be as strong as possible, the flesh side of a piece of split goat skin can be used for back-lining, covering the back from joint to joint.
It will seldom be necessary, however, to employ this method.
Perhaps nothing better shows the difference between old methods of library binding and new than this one item of back-lining. In the old methods the binders depended for strength largely upon the bands. In the new the bands are practically immaterial when the book is fastened into the cover.
20. REBACKING
At this point some binders reback to make a sharp joint, and to make the book open more easily. When the canton flannel dries it may pull the back somewhat out of shape. It is doubtful, however, if rebacking is always necessary.
21. BOARDS CUT
The book is then measured for boards which are cut to the proper size.
In measuring it must be remembered that the boards must project an eighth of an inch on all edges (except the back) forming what is called the "squares." It will also make a difference in measuring if the book is to have a French joint. (See page 46.)
22. CLOTH CUT
If the book is to be bound in cloth, this is cut the proper size. If leather backs are to be used the covering material consists of two pieces of cloth and one of leather, all of which must be cut to the proper size.
23. LOOSE BACK
If the book is to be made a loose back, a piece of coarse paper is cut the size of the book from joint to joint and the length of the back.
This is placed in the book.
24. MAKING THE CASE
(a) The cloth for a full cloth book is now glued all over on the inside. The boards are adjusted on the book ("setting the square," as the binders call it) as they ought to be when the book is finally bound, and the book is placed on the right-hand side of the glued cloth, with the back toward the middle of the case, leaving enough cloth projecting on all sides to turn in. The other side of the case is then drawn up over the board on top and pressed down firmly enough so that when it is laid back again, the board which has been uppermost goes with it. The book itself is laid aside.
The paper which is to prevent the glued cloth from sticking to the back of the book is then placed in the space between the two boards, and all edges of the cloth turned in on the boards. This forms the complete cover or case.
(b) If the book is to have a leather back, the boards are tipped lightly with paste to the end papers, allowing for the French joint. The leather is pasted and the book is then laid on the leather in the right position so that the rest of the leather can be pulled up over the back on the top board. The top cover is then laid back, the paper forming a loose back inserted, the leather turned in, and cloth sides put on and turned in.
25. MAKING OF A FRENCH JOINT
The book is now set back in the cover just described and the space between the boards and the back is creased with a bone folder while the cloth or leather is damp. This forms the French joint.
26. PASTING DOWN END PAPERS
End papers are then pasted down to the boards and the book, so far as strength is concerned, is finished. It will be remembered that the end papers were guarded with muslin, or jaconet, that the bands projected beyond the sides and were pasted to the end papers, and that the canton flannel also projected beyond the sides and was pasted to the end papers. Therefore, when the end paper is pasted to the board it carries with it first the canton flannel, then the bands and lastly the jaconet guard. This is as true of leather-backed books as of full cloth.
Strictly speaking, this makes what is technically known as a "cased" book, i. e., the case is made in one whole piece and the book fastened into it. Because leather bound books have always been considered stronger than others, and because they have always been laced-in to the boards (see page 42) before the leather has been put on, a prejudice against cased books has arisen. If the prejudice be directed against the usual commercial binding it is justified, but if directed against library books properly cased it is not justified.
27. PRESSING
At this stage the book is put under heavy pressure in the standing press until dry. A number of books are placed in the press at one time, separated by backing boards having metal projections which fit into the French joints. They should be left twelve hours at least, longer if necessary. After pressing, the book goes through a general cleaning process. In applying the glue or paste there are many chances of soiling the book. The great pressure which is applied also squeezes out glue at the head and tail. This must all be cleaned off before the book goes to the finisher.
FINISHING
28. GILDING
The gilding of a library book is a simple matter compared with that of books bound for individuals. Such books are usually meant to be artistic and their covers bear elaborate designs in gold, generally limited only by the size of the owner's pocketbook or by his taste.[1] In library binding gilding is confined to the furnishing of necessary information.
Tooling of all kinds, with the possible exception of that which divides the back into panels, is unnecessary. A description of finishing processes is unnecessary here since they add nothing to the strength of a book. A description of the method of gilding call numbers will be found on page 194.
There are three different ways of lettering books bound in light colored cloths on which gold cannot be used: (a) In gold on leather labels pasted to the back. (b) In gold on panels which have been stained black. (c) In black ink directly on the back. The first two methods make more attractive-looking books but the process adds to the expense, and in the first case the labels have a tendency to peel off. The last method is the one generally used.
In this description of processes numerous details have been omitted, because they would add little, if anything, to the librarian's ability to criticize properly the work being done by his binder.[2] In some respects the order here outlined may differ in different binderies, but the majority follow it closely.
The processes as outlined are those which should be used in library binding. There are, however, several additional points relating to binding processes with which it is well to be familiar.
Footnote 1: Finishing from the artistic point of view with an
excellent description of tools, materials and processes will be
found in Cockerell's "Binding and the care of books," Chapter 14.
Footnote 2: For instructions to the binder about type, space,
lettering, etc., see under Lettering, page 141.
RAISED BANDS
In looking at many old books bound in the eighteenth or early part of the nineteenth century, or at books bound within recent years for individuals, one will find many that have the back divided by ridges.
These are known as "raised bands." They are formed by sewing the book differently from either of the methods described up to this point.
According to this method the bands are not placed in grooves which sink them below the surface of the back, but are simply laid against the back. In sewing the thread may come out at the near side of the band and in at the far side, thus going around the band on the back of the book; or it may come out at the far side and in at the near side, thus entirely encircling the band. In either case the sewing is exceedingly strong. Since the bands are entirely on the surface, the leaves open all the way to the back of the signatures and greater flexibility can be obtained thereby. (Fig. 10.)
FIGURE 10.--Sewing on raised bands. No saw cuts except for kettle stitches. Based on illustration in Report of the Committee on Leather for Bookbinding. Edited for Society of Arts, London, 1905.
As it is much more difficult to sew and forward books with raised bands, they are not used in ordinary library work. It may be advisable, however, to use them occasionally on a few large reference books such as dictionaries, where great flexibility combined with strength is essential. In fact the merits of binding in this way are not recognized as generally as they should be.
Many books look as if they were sewed on raised bands when in reality they are sewed in the ordinary way, with false raised bands pasted on the back. They add nothing to strength and have no place in library binding.
LACING-IN
Lacing-in is a method of attaching the bands to the book, which is in general use for all leather books bound by hand. This method requires that the boards which have been cut to the proper size be laid against the grooves formed in backing and marks be made about half an inch in from the back, opposite each band. At these points holes are punched through the board which is then turned over and other holes are punched about half an inch from the first ones.
It is generally desirable to cut a groove in the board from the first holes to the edge of the board, for the bands to lie in, so that there will not be an unsightly protuberance when the book is bound. The bands which have been frayed out are then threaded through the first holes from the outside of the board inward and again through the second holes. They are drawn up tightly enough so that the board will fit close to the joint, but not enough to prevent it from lying flat.
The ends of the bands are spread out fan-wise, pasted, and hammered down smooth on the board. Before any back-lining has been put on, the boards are attached to the book simply by these bands. (Fig. 11.)
FIGURE 11.--Bands laced in, and ends frayed out. Based on illustration in Report of the Committee on Leather for Bookbinding. Edited for Society of Arts, London, 1905.
When bands are laced-in it is not customary to use anything stronger than paper for back lining; the strength of the book lies in the bands and the leather which covers the back. As long as the leather remains strong and the book does not receive hard usage this method is satisfactory. As soon, however, as the leather begins to disintegrate more strain is placed upon the bands. When the leather breaks completely the bands bear the entire burden at the joint, and eventually break.
With the process as outlined in the preceding pages one need never fear that the book will come out of the cover, or that the sides will break at the joint. Even if the leather should break the canton flannel will hold. The best library binders do no lacing-in at the present time.
FIGURE 12.--Split boards. In actual work the back-lining would cover the entire back.
SPLIT BOARDS
While the old method of lacing-in is not desirable in library binding, the method of using split boards makes a very strong book. Instead of making a case of cloth, or cloth and leather, the back lining and the bands (or tapes) are inserted in boards which have been split, or between two thin boards glued together with a space left unglued for this purpose. The covering material is put on after the book is in boards and the book is made tight backed. This is probably the strongest method of attaching a book to the boards. In fact it is stronger than is necessary for any except very heavy books which receive hard wear. (Fig. 12.)
TIGHT AND LOOSE BACKS
For years there has been a certain mild controversy regarding the relative merits of tight and loose backs for leather bound books. Tight backs are those in which the material used for covering the book is pasted or glued to the back. Loose backs are those which, by means of folded paper or a piece of paper put in as described on page 37, are prevented from adhering to the back. When the book is opened the back springs out. (Fig. 13.)
The tight back book always forms a hinge at the place where the book is opened. Since the place of the hinge is constantly changing the back of the book after much use becomes concave instead of convex, and the appearance of the book is seriously marred. Also the constant creasing of the back tends to erase the gold lettering, so that it becomes indistinct. If labels are put on they speedily come off. It is customary to use tight backs on very heavy books, though there are cases where such books have been put in loose backs.
FIGURE 13.--Tight back and loose back.
The loose-back book always preserves its shape and good appearance, even when the paper on the inside may be so badly worn that the book should be withdrawn. The strain, however, always comes at the joint; therefore if poor leather is used it will quickly wear out at this point.
Each method has its advocates, but so far as the present writer can learn, there seems to be little to choose from the standpoint of strength. It might seem that the tight-back book would be the stronger, but as a matter of fact in actual wear loose-back books seem to hold their own with the others. In fact when the soft, spongy papers are used the loose backs are obviously stronger. It seems clear that there is little choice one way or the other, and the question must be decided by the personal preference of the librarian.
JOINTS
In library binding French joints are now used in place of regular joints. Figure 14 shows plainly the difference between the two. In the regular joint it will be noticed that when the book is opened there is a sharp crease in one line from head to tail. In the French joint the strain is distributed over a much greater area. In regular joints the leather is sometimes pared at the joints to permit of easier opening of the book. In French joints the full thickness of the leather can be used. French joints are made by setting the boards away from the back about one-eighth of an inch.
When the cover is put on it is necessary to crease between the board and the back while the leather is still damp.
An excellent illustration showing the anatomy of a joint may be found on page 51 of Dana's "Notes on bookbinding for libraries," ed. 2.
Illustration: A Section of an Ordinary Joint with the board open shows that the creasing of the leather is concentrated on one line.
Illustration: A Section of a "French Joint" shows how this creasing is distributed over a great surface, and so enables sufficient flexibility to be obtained with much thicker leather than can be used with an ordinary joint.
FIGURE 14.--French joint. From Report of the Committee on Leathers for Bookbinding. Edited for Society of Arts, London, 1905.
CORNERS
Corners on library books should be rounded to prevent the board from breaking if the book falls and to prevent the cloth from wearing through at this point. Rounded corners are peculiar to library binding. As a rule they are not made by cutting off a corner of the board, but by turning in the cloth diagonally from the corner and then from the side and end. Sometimes both methods are adopted. If government specification cloth is used it is probable that "library corners" will not be necessary.
In some libraries pieces of leather or vellum are put on corners.
Leather is put on in order to raise the bottom of the boards from the shelf, while vellum is used to make the corners hard and prevent them from breaking or showing signs of wear. While both serve the purpose for which they are intended, the process of putting them on adds materially to the expense, and in most cases this is not warranted by the increased use of the book.
TRIMMING
Binders should be instructed to trim as little as possible. This is important for all books, but most of all for periodicals. In fiction and juvenile books it is important to have wide margins, because the text will remain legible for a longer period of time if protected by a margin from the contact of hands. Non-fiction books which are likely to remain in use for a longer period of years may need to be rebound and trimmed again. Therefore wide margins are essential to good wear as well as to good appearance.
It is customary to bind front covers of periodicals. Sometimes it is desirable to bind advertising pages, and it is necessary to do so when the publishers follow the pernicious practice of continuing regular articles on advertising pages. Covers and advertising pages are generally printed with much narrower margins than the body of the magazine and unless great care is taken in trimming parts of the printed matter will be cut off.
HEADBANDS
Cotton headbands can be added during the forwarding but inasmuch as they are simply pasted on they add nothing to the strength and very little to the beauty of the book. When silk headbands are carefully sewed on they add both strength and beauty. An excellent description of the process of putting on headbands will be found in Cockerell's "Binding and the care of books," page 147.
HOW TO RECOGNIZE A WELL BOUND BOOK
The ability to recognize a well bound book is necessary when comparing the work of different binders. A book should be bound in material suitable for the use which the book is to receive and in such a way as to give the maximum amount of service. It should also be as attractive in appearance as is compatible with these two requirements. In deciding whether a book is suitably bound for library use the following points should be kept in mind:
- A volume must show evidence of neat and careful workmanship.
- If the book is to be used constantly leather is essential; if
occasionally only, leather is an element of weakness.
- All books that receive hard usage should have end papers and
fly-leaves guarded with cloth. If sewed regularly the first and last signatures also should be guarded.
- Saw cuts should not be deep.
- The book should be flexible and stay flat wherever opened. (This is
not always possible in the case of overcast books or books printed on stiff, brittle paper.)
- When the book is lying flat the top should remain flat. When standing
on end the sections should not separate slightly at the back.
- The book should feel firm and compact to the hand.
- When opened the volume should not make a crackling noise due to too
much glue on the back.
- The book should have a well rounded back and the cover should fit
well at the joint. Flat backs are not desirable.
- Margins should be wide and cut straight. Periodicals should not be
trimmed so that printing on covers or advertisements is cut off.
- The book should have French joints.
- The cover should not separate easily from the book when pressure is
applied.
- Lettering on the back should be legible and put on straight.
- On opening the book sections at the back should be perfectly smooth,
showing that they have not been crushed in backing.
- Guards for plates, maps, sections, etc., should be so applied as to
leave the paper unwrinkled.
CHAPTER IV
MATERIALS
In a recent pamphlet issued by the Government Printing Office, containing a list of materials and articles used in the printing and binding of public documents, the number of items for binding alone reaches the surprising total of 171. Many of these are materials used in marbling, others indicate slight variations of color and weight in standard leathers and cloths. But exclusive of all these the number of materials called for is over forty.
It is not the writer's purpose to discuss all of these forty or more materials, but it seems necessary to mention that many materials other than those used in covering books (always some kind of cloth or leather) are used in binding. Furthermore, the strength of the book after it is bound will depend almost as much upon the materials used in its inner construction as upon those used in covering it. The inner materials, if not wisely selected as to quality or in reference to the kind of service which the book is to receive, may cause an otherwise excellently bound book to give poor service.
In general, however, a reference to binding materials means those which are used in covering books. It is the cover which renders a book attractive or unattractive, and which contributes more than any other one item, except possibly sewing, to the long life of the book. We should therefore know the initial cost of different covering materials and the length of service which each material will give under different conditions. When they are not imitations we should be able to recognize the best-known materials, either on or off the books. An unscrupulous binder can easily take advantage of ignorance of these matters.
So far as the librarian is concerned only two classes of materials need be considered for the covers of books--leathers and book cloths. This does not indicate a restriction of choice, for when we consider that leather comes from a large number of animals, that there are a great many different kinds of cloth, that cloths and leathers can be obtained in a great variety of colors, there seems to be an embarrassment of riches. As a matter of fact most librarians confine themselves to four kinds of leather and four or five kinds of cloth, each in three or four different shades.
LEATHER
The most expensive materials used in covering books and those which vary most in quality are leathers, the skins of animals which have been tanned and made flexible. The best bookbinding leathers are those which are flexible both in the skin and on books, and the surface of which is not easily damaged by friction. Owing to the many kinds of leathers and their variation in quality, it is difficult to learn to know them well.
The skins of all sorts of animals have been used for covering books.
Certain ones, not suitable for library binding, are still used for the purpose in various parts of the country, so that librarians need to become expert in their knowledge of which leathers may be employed and which ought to be rejected.
Variations in the same kinds of leathers are caused by:
(a) Age. Skins of animals which have not reached full growth should not be used for binding library books. Since they are immature, the fibres have not become tough, and they have not reached their maximum thickness. If the skins which the binder is using are exceptionally small, it is probable that the animals from which they were obtained were too young. On the other hand, the skins of very old animals should not be used, since the fibres of the skins have lost something of their flexibility and strength. They cannot be readily detected, but they are sure to give poor service.
As an illustration of the effect which age has upon leather it will be sufficient to note the well-known fact that calf skin is useless for library purposes, while cowhide within certain well-defined limits is exceedingly useful.
(b) The sex of the animal. It has been proved beyond question that the skin from the female of some animals, notably goats, does not wear as well as that from the male.
(c) Country from which they come. It is an interesting fact that the skin of a sheep which comes from Persia is not the same kind of a skin as that of a sheep which is raised in the United States. In general, it may be said that skins from animals inhabiting warm countries are more likely to be serviceable than those from the same kind of animals inhabiting cold countries. In the cold countries more of the strength goes into the fur or hair which protects it, while in warm countries a greater amount of strength goes into the skin itself.
In addition to variations due to these causes there is likely to be a certain amount of variation in different parts of the same skin. That part of the skin which comes from the back of the animal is tougher than that which comes from the abdomen. The difference is very noticeable in the skins of some animals, less so in others.
Decay of Leather. Of late years there has been much dissatisfaction expressed over the decay of modern leathers. In many cases leathers 100 years old or more are in a fair state of preservation, while many leathers--perhaps we should say most leathers--30, 20 or even 10 years old, show signs of decay, and some have rotted away almost entirely. In no way is the decay of modern leathers shown more conclusively than in a long file of the sheep-bound set of the United States Public Documents. The earlier volumes, covering the 15th Congress up to the 36th, will in general be found to be in a good state of preservation.
About the year 1860, however, marked deterioration appears. In some cases it seems as if the backs had entirely disintegrated. While a sheep-bound set is the best example of the decay of modern leathers, many libraries have been greatly annoyed by the decay of other leathers which are supposed to be much stronger than sheepskin.
So great was the dissatisfaction with modern leathers that in the year 1900 the Society of Arts in London appointed a committee to investigate modern leathers and to ascertain the best methods for preparing leathers for binding. The report of this committee was published in 1905, and a general knowledge of its contents is necessary for those who wish to know why leathers decay and how they may be preserved. Another valuable work which should be carefully studied is entitled "Leathers for libraries," published by the Sound Leather Committee of the Library Association in England. In a chapter of this book J. Gordon Parker, Ph.
D., Director of the London Leather Industries Research Laboratories, tells us that the chief causes of decay are as follows:
- The introduction of tanning materials other than oak and sumac,
stronger in tannin, and more rapid in their action. Many of these
tanning materials are unstable, and the leather produced
disintegrates on exposure to light and air.
Tanning is the process of changing hides, which are animal matter subject to decay, into material which is strong and flexible and which is not subject to decay. There are two groups of tanning materials. The one called the pyrogallol group, which includes sumac, gall nuts and oak bark, is commended by the Committee of the Society of Arts. The other is called the catechol group and is strongly condemned. Among the materials belonging to the catechol group are hemlock bark and larch, used chiefly in this country, and turwar bark used largely in tanning East Indian goat and sheep skins.
The United States Government Printing Office proposals call for leathers tanned with a pyrogallol tannin, since it has been proved that such leathers prove most resistant to the evil effects of light, heat and gas. If a skin has been tanned with sumac, or sumac in combination with oak bark, it has received the best possible preparation for its life as a bookbinding leather.
It is not possible, neither is it necessary, to have all leathers tanned with sumac. Those leathers which are intended to remain on the shelves for many decades, should be in this tannage. Those which will be discarded in a few years may be tanned in a less expensive manner. Even some of the quick, modern materials, which accomplish in a few hours what once would have taken weeks, are not too poor for leathers which are not to be kept indefinitely.
Even the expert cannot detect skins which have not been tanned and dyed properly, but leathers which last a short time may be suspected either of being improperly tanned or of having some kind of injurious acid in their composition.
- The use of dried and cured skins of variable soundness imported
from abroad. Goat, calf and sheep skins are imported into this
country (England) from all over the world; some are simply dried in
the sun, some salted, whilst others are cured with various
ingredients.
- The use of infusions of acids and other bleaching agents to
produce bright and even shades of colour.
Skins tanned with sumac are light-colored and can be dyed any desired color. Most other tanning materials, however, make darker-colored skins, which can be dyed only with dark colors. It has been found possible to scour and bleach skins with sulphuric acid and to re-tan with sumac.
- The use of sulphuric or other mineral acids for the purpose of
developing the depth of colour during the process of dyeing.
Sulphuric acid is the cause of decay of over 90% of modern bookbinding leathers. Having once been used, it cannot be wholly removed without the use of other chemicals.
- The shaving and splitting of skins for producing an even
substance.
In splitting and shaving, the long, strongest fibres of the skin are torn or cut off, and the part which remains for binding purposes is the weakest part of the skin.
- Printing and embossing grains upon leather, together with other
methods of finishing now in common use.
There are various ways of bringing out the natural grain of leathers which are perfectly legitimate and which do no harm. The danger in graining comes when the grain is embossed by means of a plate, which is heated and pressed on the skin. No good leather should ever be embossed.
- The stripping, scouring, souring and re-tanning of East India
leathers (Persians).
Some imported skins are only partially tanned, and it is necessary to wash out the tannin with some kind of alkali, which also takes out much of the natural grease of the skin. They are then treated with sulphuric acid and re-tanned. They are always poor and are seldom sold as re-tanned skins.
- The removal of the natural grease or nourishment of the skin.
The foregoing eight causes of decay are beyond our direct control. The leathers are manufactured and put on the market, and the binder has to use such as he is able to obtain. No matter how much the librarian may insist upon leathers free-from-acid, he is helpless if the binder cannot obtain them. All that he can do is to insist that leathers without acid must be used, if obtainable.
Although these causes of decay are beyond the librarian's control, there are several causes of decay quite within his power to avoid. They are the following, due to improper methods used in binding, or to physical conditions after the book is on the shelf:
- Direct sunlight.
- Gas fumes. This evil is hard to guard against if there are gas pipes
in the building. There is sure to be more or less leakage, and even a small amount of gas in the air has a bad effect upon leather.
- Tobacco smoke. This is not likely to be very detrimental in
libraries, since the rules generally forbid smoking.
- Excessive dampness, which encourages mildew.
- Extreme dry heat. A temperature much in excess of 70 deg. Fahrenheit is
likely to dry up the oil which gives flexibility to leather.
- Undue wetting or stretching the leather in covering. Some binders
soak the leathers and stretch them in placing them on the books. When the leathers dry they shrink, the fibres are strained and the life of the leather shortened.
- Use of poor paste in binding. This frequently sets up a fermentation
that is very harmful to leathers.
- Dust, especially in conjunction with dampness, is very injurious to
leather.
Doubtless there are other things which have a deleterious effect upon leathers in libraries; but if a library is well ventilated, if leather-covered books are not kept in cellars or basements that are very damp, or where direct sunlight can fall upon them, and if the binder uses good paste and proper care in covering the books, we may reasonably place the responsibility of undue decay of leathers upon the manufacturers.
The various reports quoted so far have dealt with qualities of leathers due to tanning, manufacture, method of binding and time in use. Natural or mechanical qualities of leathers have not been touched upon. Those who are interested in this phase of the question should read the report of Mr. Cedric Chivers on "The relative value of leathers and other binding materials," made at the meeting of the American Library Association at Pasadena in 1911. Mr. Chivers employed Mr. Alfred Seymour Jones, in England, to make tests which would show the tearing and breaking strain of various leathers.
These natural qualities of leathers are obviously important, but too much stress must not be laid upon them.
It is possible that a leather naturally strong and tough when new would rapidly deteriorate with age. The records as presented in Mr. Chivers' report must be taken in conjunction with facts determined by the investigation of the Society of Arts. In the main, however, it will be found that leathers which best stood the tests of the Society of Arts also showed the greatest resistance to the tearing and breaking strains made by Mr. Chivers.
Preservation of Leather. Various attempts have been made both by librarians and others to discover some substance which would preserve leather effectually after the book is bound. Some of these attempts have been temporarily successful, but time alone will tell whether leathers are permanently preserved by the treatments used, or whether applications of the preservative must be frequently made.
Owing to the fact that in law libraries practically all the books published previous to 1900 were bound in sheepskin, the lasting qualities of leathers is a question that affects law libraries more than any other. Dr. Wire, of the Worcester (Mass.) County Law Library, who has made a careful study of the problem, advises the use of vaseline or some other similar by-product of petroleum well rubbed into the leather with the bare hand and allowed to dry in the air until the leather has absorbed it.
Better results were obtained by allowing the volumes to dry in the summer by natural heat instead of artificial heat in the winter. For some books Dr. Wire makes use of a bookbinder's varnish after the softening product has thoroughly penetrated the leather. A full description of the processes may be obtained from Dr. Wire's pamphlet, "Leather preservation," published in 1911.
Some of the disadvantages of Dr. Wire's method are:
- The necessity of rubbing in the preservative from three to five
times, according to the condition of the leather at the time of first treatment.
- The care necessary to prevent the material used from smearing tables,
trucks, floor, shelves and clothing at time of application; also when books are back on the shelves the care required to keep from rubbing against them and the necessity of wiping them off when they are handed to readers.
- The tendency of books to swell at the back when first treated in this
way, demanding extra care lest, in an effort to pull out one book, a whole shelf-full fall to the floor.
- The repetition of the process after ten years.
It is possible that these drawbacks will be sufficient to dissuade all except the most stout-hearted from using this method of preserving leather. Rebinding in cloth seems to be much more simple and, on the whole, not much more expensive.
The question of a preservative is discussed in the Report of the Society of Arts, from which the following quotation is taken:
Enquiries have frequently been made as to the use of
preservative pastes upon old bindings. It has been mentioned
that the seasonings of white of egg or blood albumen usually
employed in finishing leather have some preservative effect,
and no harm can arise from the application of very thin
coatings of white of egg.
The use of ammonia to thin or
preserve the solution must be avoided, but the whites, after
thorough beating, may be rendered antiseptic by the addition
of a small quantity of camphor, thymol, or some essential oil.
Vaseline has been employed as a dressing, and, if otherwise
suitable, will no doubt have a preservative effect upon the
leather. A very moderate use of the wax, soap, and turpentine
preparations made as shoe pastes, is also likely to be
beneficial, and no doubt a special preparation might be made
on these lines which would be still more suitable.
Paraffin wax
dissolved in benzine is also harmless, and the surface to
which it has been applied takes a good polish with a flannel
after drying. Professor Proctor has experimented with a
finish introduced by the Berlin Aniline Company some years
ago for coloured leathers, with apparently satisfactory results.
The preparation is practically a very hard stearine soap with
excess of stearic acid, and is made by boiling 8 parts of
stearic acid with 1 part of caustic soda and 50 parts of water
until thoroughly dissolved, and then adding 150 parts of cold
water and stirring till the material sets to a jelly.
It is
applied very thinly with a sponge or rag, and after thorough
drying is polished with a soft brush or flannel. The alkali
present in the soap is useful in neutralising any mineral acids
contained in the leather. In very acid leathers it has been
noticed that the sodium sulphate so formed will sometimes
appear upon the surface as a white film, but this is easily
removed with a damp cloth, and the surface, after drying,
repolished with flannel.
Old books which it is desirable to preserve as long as possible in their original bindings and books which will be used very little may be treated with some form of preservative. If the book is to be much used, it would better be rebound. Dr. Wire's experiments have been carried on exclusively with law books. Whether the same processes could be used on books bound in morocco or pigskin is something that has not yet been determined. Most leather-bound books break first at the joint.
The sheep bindings in a law library would show signs of disintegration long before the leather reached the breaking point, whereas the librarian would first notice that morocco was decaying when the leather actually cracked. Once cracked, no amount of preservative would do any good.
KINDS OF LEATHER[3]
The leathers that have been used in binding books have come from all sorts of animals, but so far as the librarian is concerned the skins of four animals only need be taken into consideration--the sheep, the cow, the pig and the goat. In England some experiments have been made with sealskin, but it has not been used long enough to give any definite idea of its resistance to the encroachments of time.
Footnote 3: The prices of leathers given in the text are those
which prevailed during the summer of 1915.
SHEEPSKIN
Sheepskin is a soft, flexible leather with weak fibres, and with a surface easily abraded. It has been used for bindings practically ever since books were put into leathers; and, under the old methods of tanning and manufacturing, proved satisfactory. In many libraries it is possible to see leather books bound in sheep in the 17th century which are in a good state of preservation. Even the sheep of the beginning of the 19th century is frequently well preserved. Since 1860, however, the quality of sheep has greatly deteriorated.
This is bad enough, but unfortunately sheep likes to masquerade under the name of morocco and other leathers of a better grade, so that its use is much more extensive than appears at first sight. In the process of imitation the grain of the leather imitated is stamped on the skin. When this is done it generally takes an expert to detect the fact that the leather is not what it pretends to be, and even experts are sometimes deceived after the leather is on a book.
The strongest sheepskins are made when tanned with oak bark. Sumac, which is such a valuable tanning material with other leathers, is here inferior to oak.
There are two kinds of sheepskin, the wool sheep which is known to all, and the hair sheep which is not found in the United States, and which in reality is a cross between a sheep and a goat. The hair sheep comes from India, China, South America and Africa, generally from mountainous districts. It has a much tougher fibre and is a better wearing skin than that of the wool sheep. Unfortunately most of these skins, which are all imported, are made into shoe leather. When properly tanned they are very suitable for library binding, and their use for that purpose is increasing.
The wool sheepskin in its natural color has been used for many years for binding law books. It is seldom used for anything except government documents and law books, and for this reason is known as "law-sheep."
Roan. Roans, the term used for sheepskins after they are dyed, can be used advantageously on books which will be handled a great deal, and which in any event will not stay on the shelves indefinitely. Properly tanned and dyed, they make a satisfactory leather for a time, but their life under the best of conditions seldom exceeds ten or twelve years.
While this is true of good roans, it unfortunately remains true that in the United States, at least, it is difficult to get roans that are properly tanned and dyed. Therefore, unless one is sure that the quality of the skin is the best, he should use no sheep under any conditions.
Skiver. Skiver is the outside of a sheepskin which has been split, the inner side being known as the flesher. It is a leather much used for commercial binding, but since the splitting process takes away a great part of the strength of the skin, leaving it not much stronger than strong paper, skiver is wholly unfitted for library use.
COWHIDE
Cowhide, sometimes known as American russia, is a leather which has increased enormously in use in the last twenty-five years. It is a thick, coarse leather, rather unattractive in appearance, strong when new, but with age rapidly deteriorating in quality, even when no deleterious substance has been used in tanning or dyeing. It is a harder leather to work than roan, but the quality is much more uniform and it can be used advantageously for binding fiction and other books which will be much used.
In its natural state (undyed) it can be used in place of law-sheep for law books, but has a tendency to become dark. It can be obtained in many colors. Since it is too thick a leather to be used in full thickness, practically all skins are split, and the amount of flesh left with the grain determines the weight of the leather. A greater or less amount is taken off according to the purpose for which the leather is intended.
Bookbinding cowhide costing 20c to 25c. a square foot is the lightest weight leather that has the right to be called cow.[4] The life of cowhide is from five to twelve years.
Buffing. Buffing is practically only the grain of cowskin from which almost all the flesh has been split. It is not suitable for library books, since it is very thin and begins to disintegrate in less than five years. After it is on the volume it is hard to detect, so that some library binders have been tempted to use it instead of cow. But as buffing is never sold as cow, the library binder has no excuse for keeping it in stock.
Footnote 4: This is the normal price of cow. The European war has
had the disastrous effect of raising the price and lowering the
quality. Until conditions become normal again all cowhide should be
shunned.
PIGSKIN
Pigskin is one of the strongest leathers, having a hard, resisting surface and a good, tough fibre. In the grain, the holes which were left when bristles were removed are plainly visible, giving the leather a distinctive appearance, which can be imitated successfully, but which is much less often imitated than the grain of morocco. If there be doubt of the genuineness of pig, soak a piece of the leather until it has absorbed a quantity of water, and then stretch it. If the grain pulls out, it is imitation; if genuine, the bristle holes still show plainly.
Oak bark tanning is the best for this leather, and, since it is more nearly gristle (less fibrous) than other leathers, dyes and chemicals should not be used which will interfere with its quality of resisting friction. It should be used in its natural color whenever possible.
Pigskin frequently comes in skins which are too thick for the binder to work easily, or which are very uneven in thickness. In such cases the paring down of the skin is likely to injure its strength. Because of its thickness pig is generally supposed to be more suitable for large than for small books, but inasmuch as several binders have used it successfully for years on small books, it may be taken for granted that it can be used with good results on all books, large or small, which are to receive hard usage. It needs constant handling, and the absorption of a certain amount of oil from the hands to keep it pliable. Otherwise it dries rapidly and cracks along the joint.
This, however, is true of all leathers to a greater or less extent. Pig costs from 40c. to 45c. a square foot.
GOAT
The leather which makes the strongest and most attractive binding comes from the skins of goats and is called morocco, because it originally came from that country. In the course of time goat skins from other countries were tanned with sumac (originally a distinguishing characteristic of a genuine morocco), but the same name was applied so that we now have the paradoxical terms, Turkey morocco, Levant morocco, etc. Moroccos have a beautiful grain, are flexible, soft and pliable to the hand, and resist hard wear; qualities which contribute to their great popularity.
Morocco varies greatly in quality as well as in appearance.
Unfortunately the skins which are best in quality, considering the length of time they will wear, are not always those best in appearance.
The skins of goats with long hair from the colder countries make beautiful bindings; but the skins of goats from the hot countries, such as the interior of Africa, having short hair, while not so attractive in appearance, are tougher and wear longer. In addition to the many grades of genuine morocco there are as many more imitations of it made from sheepskin, cowhide, etc. Only the expert can detect some of them in the skin, and even he may be deceived when the leather is on the back of the book.
In general it should be said that genuine morocco is the most expensive leather that a library can use, and that it can be used to the greatest advantage only occasionally. It makes an excellent binding for large reference books which are constantly handled, for art books which must be attractively bound, and for some periodicals which are much used in reference work. It is not used nearly so much in libraries to-day as it was ten or fifteen years ago, and it is quite safe to say that it will be used less ten years from to-day than it is now.
Levant morocco, made from the skins of Angora goats, is the most expensive and most beautiful leather used in binding. It has a large, prominent grain, but is far too expensive for any library to use, especially when it must be conceded that in its wearing quality it does not equal that of some less expensive moroccos. Mr. Chivers' test showed that so far as tensile strength goes, this leather is very much weaker than many leathers much less expensive. When the skin has been subjected to pressure until the surface is smooth it is known as "crushed levant."
Turkey morocco, made of skins of goats from Turkey, is a very strong, durable leather which all libraries will find occasion to use from time to time. It is very easily imitated. Under exposure to atmospheric conditions existing in many libraries its life may not extend beyond thirty years. In one library at least, where conditions of light and heat were poor, the best Turkey morocco that the market afforded showed signs of disintegration within twelve years. Good Turkey morocco can be obtained for 35c. a square foot.
Persian morocco, which comes from the skin of a Persian sheep (not goat), is not particularly attractive in appearance and is very poor in quality. It is used extensively for commercial work, but is absolutely valueless for library binding.
Niger morocco is a goat skin which comes from the interior of Africa, generally by way of Tripoli, and is by no means a recent discovery, though we knew little about it five years ago. It is tanned by natives according to some method of vegetable tanning not completely known at this time. While in appearance it is not so attractive as some other moroccos, because of blemishes due to carelessness in handling and to the imperfect removal of some of the hairs, it has been proved by the tests made under the direction of Mr. Chivers to be stronger than all other moroccos; the inference is that it is more durable. Until recently it has been very hard to obtain in the United States.
Bock morocco is not a morocco but a split Persian sheep so poor in quality that it is mentioned only to be condemned.
CALFSKIN
Calfskin in all its various characters, such as divinity, kip, marbled, mottled, smooth, tree, or just plain calf is a very beautiful leather much used in the past for binding books for individuals. For this purpose it has, of late years, been crowded out by Levant morocco. It has a soft, smooth surface which disintegrates rapidly under the action of heat and gas and has little strength even for temporary use. For the library it is useless.
RUSSIA LEATHER
This is a brownish-red leather made from the skins of different animals, tanned with willow bark and filled with a preparation of birch oil which gives it its peculiar odor. Neither in its genuine form nor in imitation is it a useful leather for libraries.
SEALSKIN
Although experiments have been made with it in some English libraries sealskin has never been much used in the United States for library binding. It is made from the skins of the hair seal, the supply coming from all parts of the North Atlantic Ocean. According to Mr. Douglas Cockerell and other binding experts in England, the skin is peculiarly suited for library use. It is reported to be a hard-wearing leather, tough and pliable, even in quality so that no part of the skin must be discarded because too thin or too weak, and possessing a beautiful grain. The price ranges from a point somewhat higher than that of the poorer moroccos to one somewhat lower than the higher prices.
Unfortunately it can be easily imitated.
VELLUM
Probably no discussion of leather is complete without mentioning vellum, a binding material which does not resemble leather, but which nevertheless is made from calfskin or sometimes from goat skin. It is prepared by the use of lime, and as far as the actual wear on flat surface is concerned, is perhaps better than any leather. It is, however, very susceptible to moisture, which makes it warp; and to light, which makes it hard and brittle. Since it is very hard, does not bend easily and is hard to work, its chief use is on the corners of books to protect them and make them less likely to break or rub. Large libraries have used it somewhat for this purpose, but the use is dying out.
In making a study of leathers it is well to obtain samples of all kinds, including those which are unsuitable for library use, and to examine them carefully, noting the appearance of the grain, thickness of skin, flexibility, and softness of surface. Perhaps more money can be wasted through ignorance of the comparative values of different kinds of leather which it is permissible to use in library binding, than in mismanagement of any other part of binding.
CLOTH
Cloth is fully as important as leather in the economy of binding.
Several years ago it was the custom to bind periodicals and other books which were used comparatively seldom in leather, while fiction, juvenile and other books which wore out quickly were bound in cloth.
Recently the opposite course has been more favored. Books which receive unusually hard usage and are in the hands of readers constantly are bound in leather; while those which are used seldom, including periodicals, are bound in some kind of cloth. Without doubt the change is a wise one. Even the best of leather disintegrates in time under the action of heat, gas, light, etc., and to-day many a volume bound in leather ten or fifteen years ago has parted from its sides, necessitating rebinding or recovering.
Had it been bound in a good quality of cloth it would to-day be in good condition, and probably would remain in good condition for a hundred years. It requires considerable courage to change the binding of a good set of a standard periodical, such as the Atlantic or Harper's, from an attractive half morocco binding to an unattractive buckram. Unquestionably, if economy is an object, the change should be made, except possibly in the case of a library which uses these periodicals daily.
Every librarian must decide each case for himself strictly according to the use the set is to receive, always bearing in mind the fact that leather disintegrates with time, whereas cloth does not unless exposed to excessive moisture.
No cloth which is suitable for library use is perfectly satisfactory because it has not the strength of good leather, cannot be used advantageously on very heavy books, soils easily and with use grows soft and flabby, especially along the joints. But on the other hand even those not suitable for libraries which are used by the publisher on cheap books are much better than poor grades of leathers, such as skiver, bock, buffing, etc.
The requisite qualities of a good cloth are:
(a) Endurance when folded back and forth in the same place, so that it may withstand the wear at the joint caused by opening the book.
(b) Smoothness, so that there will be a comparatively small amount of friction when withdrawing a book from between two others on the shelf.
(c) Ability to withstand constant rubbing back and forth on tables.
(d) Color that is fast when exposed to light; if possible it should be fast to water also, though this is less important.
(e) Color should be dyed in the piece, not pressed in by machinery.
Many cloths have some of these qualities but few have all of them. So far as is known to the writer only the grade of cloth described on page 77 has the last qualification.
Practically all cloth used in the United States is made of cotton. The best cloths are manufactured by The Holliston Mills, Norwood, Mass.; The Interlaken Mills, New York City; The Joseph Bancroft & Sons Company, Wilmington, Del., and by the Winterbottom Company and the Manchester
Book Cloth Company in England. Since a number of grades are made in
several different patterns and a great number of shades for each grade and each pattern, a variety of choice is permitted. As a matter of fact, however, most librarians select a good grade with a regular weave and confine themselves to a few standard shades, such as dark green, brown, red, dark blue, and tan.
Since the strength of the warp is much greater than that of the weft, it is advisable when possible to cover books with the warp running across the cover. This, however, may entail some hardship on the binder for it may frequently happen that in order to cut his cover economically he must make the warp run lengthwise of the book. If a strong cloth is used the advantage is not great enough to be insisted upon.
Each of the American firms mentioned makes three distinct grades, all of which libraries may use. Each firm uses a different name for each grade.
In other words, there are no general names which can be used for the corresponding grade in all makes. Therefore for the purposes of this chapter these cloths will be considered under the heads of Grades 1, 2 and 3, but it must be remembered that this is an arbitrary designation not known to the trade. Under each grade will be given the specific names used by the three manufacturers.
GRADE 1
Grade one of cloth, the cheapest that a librarian may use, is not made of the best quality of cotton thread and should never be used under any circumstances for full binding. It may be used on the sides of books bound in leather; if this be done the corners should be covered with vellum, for this cloth does not withstand hard usage and is likely to fray at the corners. It is a cloth commonly used by publishers, but should be used sparingly by the librarian. "Art vellum" made by the Interlaken Mills, "Aldine vellum" made by the Holliston Mills, and "Linen finish" made by the Joseph Bancroft & Sons Company, come within this grade.
GRADE 2
(a) Grade two is made of a better grade of cotton and with a closer weave than the preceding, but is not sufficiently strong to be used for full binding. It can be used more satisfactorily than the preceding on the sides of books bound in leather or duck.
In common with all cloths, except the buckram made according to the government specifications (which will be discussed later), the different colors are not made, as one might suppose, by dyeing the cloth after it is woven, but by mixing the color with the sizing or starch which is used in finishing the cloth, and pressing it into the cloth by machinery. As a natural result the color rubs off with wear and the natural gray of the original cloth as first woven appears.
"Art canvas" made by the Interlaken Mills, "Classic buckram" made by the Holliston Mills, and "Polished buckram," by the Joseph Bancroft & Sons Company come within this grade.
(b) Buckram. Under the name of buckram various grades of cloth are manufactured which resemble to a greater or less degree those mentioned under Grade 2 (a). Generally it is a coarsely woven cloth stiffened with glue or sizing, and the term originally indicated that the cloth was made of linen. At the present time linen buckram made in England can be obtained, but all that is manufactured in the United States is made of cotton. Linen buckram costs much more than cotton and it is doubtful if it is any more serviceable. All of the three manufacturers mentioned make buckrams.
GRADE 3
Prior to 1907 the Congressional set of government documents distributed to the depository libraries had been bound in sheepskin and the leather on the volumes had disintegrated so much as to make the set a hard one to care for. In 1907 the Congressional Printing Investigation Commission asked librarians of depository libraries to suggest, without considering cost, suitable binding materials for Government Documents. The number of replies received was 124, embodying suggestions as follows: full sheep, 11; half-russia, 78; cloth, 25; buckram, 70; linen duck, 20; canvas, 19.
Some librarians expressed more than one preference, so that the total number of preferences was greater than the total of those replying. Most of those who favored sheep did so because of their desire for uniformity. Those who favored half-russia undoubtedly desired half American russia, or cowhide. 134 expressed preference for some form of cloth.
After receiving the replies from librarians the Printing Investigation Commission obtained samples of cloth from various cloth manufacturers in the United States and the Bureau of Standards made a series of chemical and physical tests to determine the durability of these cloths. Chemical tests were made to discover whether the colors were fast when exposed to light. It is to be regretted perhaps that no tests were made to determine whether the cloths were fast to water and that this qualification was not included in the final specifications.
Admitting, however, that a cloth which is fast to sun and water both is a valuable cloth for bookbinding, it is evident that the quality of fastness to water is not a vitally important one for cloth used in the United States. The total number of books injured by water is so small as to make insistence upon this quality entirely unnecessary. If books become so soiled that they need to be washed they should be bound in waterproof cloth.
Because many volumes of Government Documents are sent to Porto Rico and the Philippines where insects eat almost anything of an animal or vegetable character, the desirability of the cloth as an article of diet for insects, was also tested.
The physical tests indicated:
a. Number of threads per inch of warp and weft.
b. Absorption of moisture.
c. Weight per yard.
d. Tensile strength.
e. Amount of stretch.
f. Amount of friction developed by rubbing two pieces of cloth together.
This test was made because the friction developed in taking a book from between two others is an important matter when a shelf is full of books.
If the friction is great the wear on the back of the book is correspondingly excessive.
g. Endurance when folded back and forth in the same place.
h. Endurance under extraordinary conditions of rubbing.
Some of these qualities, such as tensile strength, amount of stretch, etc., were comparatively unimportant, but the tests for all were severe and contributed much to our knowledge of the qualities which should enter into the composition of durable book cloths.
After a very careful consideration of the results of the tests and a thorough examination of the samples submitted, a committee of librarians and government officials unanimously chose three samples as the best of all those submitted by the manufacturers. Of these three samples the cloth numbered 666 was considered the most satisfactory.
Although these three samples were excellent, they all had one defect--the color was pressed in by machinery, not dyed in the piece.
After various experiments had been made by the manufacturers this defect was remedied. The Government Printing Office then advertised for bids on cloths which would meet the Specifications drawn up by the Bureau of Standards (See Appendix A). Since that time all the Government documents which continue the old sheep-bound set have been sent to depository libraries bound in cloth made according to these specifications.
This cloth is known sometimes as Government Specification Cloth, but is manufactured under the specific name of "Library buckram" by the Holliston Mills, "Art buckram" by the Interlaken Mills, and "Legal buckram" by the Joseph Bancroft & Sons Company. The first two are made in pieces about 40 yards long and 38 inches wide, the Bancroft cloth in pieces 43 yards long and 43 inches wide. It must be admitted that this cloth is not quite so attractive in appearance as some of the old cloths which are not so durable. Some binders claim that it is hard to use.
On the whole, however, it supplies a long felt want and is the strongest cloth made that is at all attractive in appearance.
DUCK
Duck or canvas, a rough, heavy cloth much the same in quality as sail cloth, is the strongest cloth used in binding, but has some very decided drawbacks which militate against its use, except when the question of strength overshadows all others. It always makes an unattractive-looking volume--some of the more fastidious librarians rebel against its use; and it readily absorbs dirt and moisture, making it disagreeable to handle if the book has been much used. Duck having a double twisted thread in the weft is much more compact and absorbs dirt and moisture much less rapidly than other kinds.
It should be used on the backs (never for full binding) of newspapers and such periodicals as are too heavy to put in library or legal buckram.
IMPERIAL MOROCCO CLOTH
Imperial morocco cloth, manufactured by the Winterbottom Book Cloth Company in England, is made of linen thread and finished with a grain to resemble leather. The kind most used in the United States resembles a straight-grained morocco. It is an excellent cloth in appearance, as well as in durability, but its cost is 50% greater than that of the Government Specification Cloth. It may be used on semi-popular books which will not receive a great amount of use, but which should be as attractive in appearance as possible.
WATER-PROOF CLOTHS
There are several cloths which are waterproof and therefore easily cleaned when the covers become soiled. The best of these are durabline, used exclusively by Cedric Chivers; rexine and pluviusin, used almost exclusively in England; keratol, made in Newark, New Jersey; and fabrikoid, made by the du Pont Powder Company, Wilmington, Delaware. All of these cloths are said to be acid, alkali and germ proof, do not absorb grease and can be washed with soap and water.
They are strong, durable cloths, but they have at first a disagreeable odor, are hard to work and hard to letter in gold. In the application of paste to most waterproof cloths, either in the process of binding or in attaching labels to the back, it is first necessary to break down the surface of the cloth or the paste will not hold. This disadvantage no longer exists in the case of fabrikoid. Keratol and fabrikoid are made to imitate leather and are frankly sold as such. Probably the use of these cloths in libraries will always be comparatively small.
Because they can be easily cleaned they may be used on the sides of juvenile books, and in rare cases for full binding.
GLUE
No very definite rules can be laid down as to what kind of glue should be used. The matter must be left largely in the hands of the binder, who must see that it is strong, yet flexible; not too poor in quality nor yet the most expensive kind which is generally used on furniture. This is too brittle for bookbinding use.
The best glue for bookbinding is made from skins and shows a dark wine color in the cake. Light colored glues are made chiefly from bones and are not usually so good. To prepare glue for use, soak small pieces in water over night and in the morning melt in the glue pot. It should never be boiled. A careful binder will see that utensils are kept clean and that glue is used in the proper thickness.
Flexible glue, which does not become too hard either before or after use, is made by mixing glycerine with good glue. It has no special advantages for use by binders, but can be used in the library itself for some of the repairs which assistants may have to make.
PASTE
(For paste used in mending, see p. 167).
The best paste is that made in the ordinary way with flour and water.
The paste should be fresh, for if it is not a certain fermentation takes place which is injurious to the book, especially to leather.
BOARDS
Not the least important part of the make-up of a finished book are the boards forming the sides. There are practically four grades of boards which are known as strawboards; binders, cloth or millboards; semi-tar, and tar boards. The cheapest grade is the strawboard, for which there is no place in library work.
Mill or cloth boards, used for practically all library work, are generally made from waste papers of all kinds, though some may have an admixture of rags. Clay is also mixed with the waste paper pulp and the whole subjected to heavy pressure in the final stages of manufacture.
They are made in two sizes, 20 x 30 and 23 x 29 inches, and are put up in 50-pound bundles, the number of sheets in the bundle indicating the thickness of the board. The thickest is a No. 12 which has 12 sheets in a 50-pound bundle. They may have as many as 70 sheets in a bundle, which makes a very thin board. A 20 or 25 board should be used for fiction and juvenile books and a 16 or 18 for heavier books such as magazines.
Prices of good cloth boards run from $40 to $50 a ton.
Semi-tar boards, made from better grade stock than mill board, should have in their composition a certain amount of rags and hemp or naval cordage. They come in the same sizes and weights, costing about $70 a ton.
Tar boards are the best boards obtainable. Made of naval cordage, they are very tough and hard to work. Many of them are allowed to season, in much the same way as lumber seasons, in order to prevent warping. They are much too expensive for library use, sometimes costing as much as $110 a ton.
The matter of boards is not one about which the librarian need exercise great watchfulness. Binders generally use a very good quality, though they sometimes use too thin a board on a heavy book, such as a newspaper or large folio. In such cases a board of suitable thickness can be made by pasting or gluing two or more together.
THREAD
At one time there was no question but that the best thread to be used in binding was linen. In the light of present knowledge it may be doubted if this is true under all circumstances. All commercially bound books, without exception, are sewed with cotton thread. Even such large books as the Century Dictionary, Webster's Dictionary and the United States Catalog of 1912 are sewed with cotton thread.
Since it was unquestionably the aim of the publishers of all these books to issue them in the strongest possible bindings, it is reasonable to suppose that linen would have been used if it were really the best for the purpose. The main reason linen thread has been advised for so long is because its tensile strength is much greater than that of cotton. On the other hand, it is just as true that what we may call the fraying resistance of a cotton thread is greater than that of linen.
Take two threads of the same size, one cotton and the other linen, make a loop of each thread with one inside the other, saw back and forth, and the cotton will always cut the linen thread. Furthermore, linen thread deteriorates in quality unless very carefully stored. The publishers soon discovered these facts, and since tensile strength is not an important attribute in a thread that is being used in a book sewing-machine, they use a cotton thread with thoroughly satisfactory results.
In the case of library binding, however, the books are always sewed by hand and the sewer, as she draws the thread tight, is obliged to use some strength; for this reason tensile strength is an important attribute. Hayes' Irish linen thread is generally specified. The Barbour thread is referred to by Mr. Dana and by others, but the writer is not familiar with its use.
Other materials used in binding are gold leaf, paper for end papers, tape, headbands, cord and various concoctions used in finishing the books. Gold leaf should be 18 to 22 karat, and neither aluminum nor silver leaf should be used. Paper for end papers will vary somewhat with the size of the book, but should never be lighter in weight than a 60-pound manila. Large libraries may find it desirable to have an end paper specially made for their own use. Tapes should be linen and not over three-eighths of an inch wide. Cord for use in sewing in the regular way (not overcasting) is a soft twine which can be obtained from all dealers in bookbinding supplies.
For all books less than twelve inches in height use four-ply cord; for larger books, five-ply.
CHAPTER V
SPECIFICATIONS
After the librarian has definitely decided upon the binder whom he wishes to employ he must, especially in dealing with binders who are not accustomed to library work, draw up specifications as to ways in which he wishes different classes of books bound. If he has employed a binder who thoroughly understands library binding, he may make use of the binder's knowledge in drawing up the specifications. Under certain circumstances it may be wise to enter into a contract with the binder, but ordinarily in the United States such a course will not be necessary.
After the specifications have been prepared and a schedule of prices agreed upon, the librarian always has the right to refuse to pay for books not bound according to specifications. Therefore, a definite legal contract is not necessary. The librarian, except in the case of a few libraries which according to law must give their work to state officials, is always at liberty to take his custom from one binder and give it to another. Thus sufficient pressure is brought to bear on the binder.
Although the present chapter gives definite specifications for the binding of various classes of books, it is always wise to show a certain latitude in the use of specifications. Local conditions, the papers used in bookmaking which seem to become poorer and poorer with each succeeding year, and the kind of a library which is to use the specifications--all these must be taken into consideration when specifications are drawn up. Moreover, the best specifications will accomplish little if they are not followed by the binder in a workmanlike manner, while good workmanship will sometimes make up for omission of important details in the specifications.
In the main, it will be found that the following specifications may be used as a guide, except possibly in the case of some reference and college libraries which do not issue books for home use. It has seemed best to place first general specifications which apply to all books, followed by additional specifications for each kind of books treated.
The way in which these specifications are carried out is described in the chapter on Processes.
GENERAL SPECIFICATIONS
- The binder is responsible for all books consigned to his care and
must replace or pay for all books lost or injured. When one considers the large number of volumes passing through a bindery, coming from many different libraries, the number of books for which the binder is unable to account is surprisingly small.
- The librarian is the judge of whether the book is bound according to
the specifications. Since he has submitted the specifications and the binder has agreed to them he should be the sole judge of the result.
- The binder will be allowed to depart from any specification if it is
desirable in the interests of good binding. He must, however, prove that he is justified in so doing.
- Books must be paid for according to a schedule of prices agreed upon
by the binder and librarian.
- The size should be determined by measuring at the back of the volume
after it is bound. It might be wiser, perhaps, to measure the book before the boards are put on, so that binders would be sure to trim the book as little as possible. It is the universal custom, however, to pay according to the measure of the book with the boards on. This may possibly tempt the binder to increase the square of the book just enough to group it with the next larger size so that he can charge more for it.
- All items not covered in the schedule of prices may be charged for at
the regular rates of the binder for such work.
- All books not oversewed are to be sewed all-along with Hayes' Irish
linen thread, suiting the size of the thread to the requirements of the book; No. 25 for light, No. 20 for medium and No. 16 for heavy sections.
- Cloth must be used for sides of all books bound in half-leather or
half-duck. Never use marbled paper except occasionally on newspapers.
- Unless otherwise specified, cloth which conforms to the
specifications of the Bureau of Standards, or Imperial morocco cloth, must be used for full binding. For sides of leather bound books a somewhat cheaper grade may be used.
- Duck should have a twisted, double thread in the weft.
- Moroccos or pigskins must be guaranteed by the manufacturer to be
free-from-acid.
- Glue must be best quality of binders' or flexible glue, and must be
used sparingly.
- Poor materials of any kind must not be used.
- In taking books apart, all old glue, paste, back-lining, paper,
etc., should be carefully removed.
- The binder should expect to do a certain amount of mending of torn
pages and guarding of weak signatures, but should be allowed to charge extra when the amount is excessive.
- The text of all books must be collated by binder and imperfect books
returned to the library. (See under Processes, Collation, p. 15).
- All illustrations of whatever character printed on single leaves
must be guarded with thin, tough paper and the guard folded around the adjoining sections.
Some librarians and binders advocate the use of cloth guards but this seems hardly necessary. The cloth guards tend to swell the back of the book, especially if there be many plates, while the thin, tough paper is strong enough for ordinary books. Folded plates should never be sewed through the middle of the fold, but should be mounted on guards so that the plates will open out nearly flat when the book is opened. Folded maps, or other folded plates which may be consulted often should, unless otherwise specified, be guarded with cloth which is as wide as the book, so that they may be thrown entirely outside the book and lie flat on a table.
- Illustrations which are folded more than once, such as maps, should
be carefully cut and mounted on thin cloth in such a way as to allow for the folding to come on the cloth alone, not on the paper.
- Stitching (that is, sewing signatures lengthwise with a
sewing-machine) or old-fashioned whipstitching, is not permitted for any books; with the possible exception of newspapers.
- In sewing three bands or tapes must be used for eight-inch books,
four for twelve-inch, etc.
- Tapes, or bands, and back-lining must project at least an inch and a
quarter on each side of the book.
- All books should be lined on the back with canton flannel as
described in the chapter on Processes, except in a few cases where it may be advisable to use duck or a flesher. This eliminates lacing-on of boards.
- Adjoining leaves of fly leaves and end papers must always be pasted
together.
- Books must be trimmed as little as possible.
- All books should have rounded corners.
- All books must have French joints.
- All books, unless otherwise specified, will be fastened finally into
the covers by pasting down end papers. Tight-back books will in addition have the back glued to the book.
- Books should be loose-back unless otherwise specified.
- Edges should be sprinkled unless the library specifies gilding on
top. The color used may be varied to harmonize with the color of the book.
- Books must be pressed until thoroughly dry.
- Binders must keep a record of each book, whether periodical or not,
which has a volume number.
This record, commonly known as a "rub" or "rub-off," shows the size of the book, kind of binding and exact lettering. Whenever other volumes of the same work or same periodical are received they will be bound according to this record, unless the librarian has specified a different material, or different lettering. In such a case the matter must be referred to the librarian before the book is bound. If a binder receives a book with a volume number and has no record of previous volumes, he should ask the librarian for a sample volume, unless it is obviously a book for which there could be no sample, such as the first volume of a periodical giving contemporary dates.
- The binder is expected to paste in book-pockets and book-plates
when furnished by the library but may charge extra for the work.
- The best gold leaf must be used in lettering unless cover is light
enough in color to take ink. Leather labels should never be used.
FICTION AND JUVENILE BOOKS
It seems to be fairly well proven that all fiction and juvenile books should be bound in some kind of leather, preferably cowhide.[5] Objections to this are heard from time to time, but the objections come chiefly from the large steel towns where the sulphur in the air has a bad effect on leathers. In most communities leather will outwear cloth and in any event cloth becomes shabby, even when perfectly strong, much more quickly than leather. When the French joint is used the leather need not be pared and ordinarily will outwear the paper of the book.
Follow general specifications as outlined above, supplemented by the following:
- Books should be bound in one-half cowhide (American russia). Roan may
be used if the librarian is sure that it is good.
- Fly-leaves should be made of white book paper, 70 pounds to the ream
and guarded with jaconet.
It is apparent that when fly-leaves are guarded with cloth they are sewed as a separate section and not tipped on as is done in ordinary binding. Since practically all fiction and juvenile books are oversewed, it will not be necessary to carry the guard around to the inner side of the fold.
- End papers may be made of paper specially made for the binder, but it
should be equal in strength to an 80-pound manila paper and should be guarded with jaconet on the outside of the fold in the same way as fly-leaves.
- If book is not oversewed the first and last sections must be guarded
with jaconet.
- Nearly all books should be sewed with some modern method of
overcasting.
It is probable that in every lot of books sent to the binder there will be some fiction and juvenile books which could be sewed in the regular way through the signatures either on bands or on tapes, but the number is so small that the binder finds it easier to sew all the books alike.
In any event only those which have the backs of the sections unbroken the entire length and which, in addition, are seldom used, should be sewed in the regular way.
Footnote 5: See footnote, page 66.
NON-FICTION
- Books should be bound in full cloth.
- Books in which the backs of sections are not injured, or which cannot
be easily mended may be sewed regularly. The rest must be oversewed.
- In all other respects the preceding specifications should be
followed.
PERIODICALS
There is no place in a small library where good judgment will do more to make the library efficient at a minimum cost than in the binding of periodicals. The use of libraries for reference purposes is increasing and the use of periodicals is made easy by means of the periodical indexes. The enthusiastic librarian who wishes to answer all questions will be tempted to bind more periodicals than are really needed, thus impairing the efficiency of the book fund. On the other hand, to some the cost of binding may seem so great that some useful periodicals will remain unbound. But it is not necessary to throw away unbound periodicals.
If they are to be used only now and then in reference work, it is a good plan to wrap them in stout manila paper with stiff boards on the outside, letter carefully on the back and file away on the shelves in their regular places among other periodicals.
Supplement the general specifications by the following:
- Fly-leaves should be made of white book paper, 80 pounds to the ream,
guarded with jaconet on both sides.
- End papers may be made of special papers used by the binder, but it
is wise to have a 100-pound manila guarded with jaconet on the outside and also on the inside of the fold.
- First and last sections must be guarded with jaconet.
- Books 10 inches in height should be sewed regularly on four bands or
on tapes one-quarter of an inch wide; larger volumes on five bands or tapes. Sew all-along, passing needle through center of tapes.
- A millboard as heavy as the weight of the book will allow must be
used.
- (a) Books should be bound in full cloth made according to the
specifications of the Bureau of Standards. As light colors, which may be lettered in ink, show dirt very readily it seems better to use a dark color and letter in gold.
(b) In large reference or college libraries there are certain periodicals that receive constant use. It would be a mistake to bind such volumes in cloth, because no cloth will endure the wear that they receive. They should be bound in leather, preferably Turkey or Niger morocco. On no account should American russia be used.
- If leather is used the sides should be covered with Bureau of
Standards cloth.
NEWSPAPERS
Because newspapers are printed on wretched paper which it is freely admitted will disintegrate in a comparatively short time, the question when to bind and when to throw away is a hard one to decide. For the small library it is surely unwise to bind any except the local paper, which will be used from time to time for local history. In many cases it may be wiser simply to wrap the volumes to protect them from the light and file them chronologically. The librarian of the large library, however, no matter how disgusted he may be with the poor quality of paper used finds it necessary to bind a number of newspapers.
When bound they will last twenty-five years or more, during which time they are sure to be used sufficiently to warrant binding.
Newspapers must be kept away from light, heat and moisture. If possible, keep in a dark closet until ready for binding. Publishers of local papers ought to give a copy for binding.
- Newspapers must be bound in one-half duck, best quality.
It is never under any circumstances wise to bind newspapers in leather.
Duck, to be sure, gathers dirt easily, but it seems to be the only material sufficiently strong and long-lived for binding newspapers.
- Fly-leaves and end papers should be made of extra heavy paper well
guarded inside and outside the fold.
- It is permissible to stitch sections lengthwise before sewing
regularly on bands, but oversewing is preferable.
- Boards of double thickness must be used. It is best, perhaps, to make
the boards by gluing or pasting two boards of ordinary thickness together.
- Corners should be covered with vellum tips.
- Tight backs must be used.
- Sides must be covered with paper.
This facilitates the handling of the volumes. If cloth sides are used on newspapers it increases enormously the labor in shelving them and even of using them on ordinary library tables. In libraries that can afford to shelve newspapers on patent shelving with rollers, cloth sides are preferable.
- Libraries that can afford it should use a fibre-filling preservative
on the edges. (See page 116 of the Bulletin of the American Library Association for 1912.)
REFERENCE BOOKS
Reference books should be bound in the same way as fiction or juvenile books, except that morocco, instead of cowhide, should be used for books constantly handled. Books used only occasionally should be covered with cloth made according to the Specifications of the Bureau of Standards.
Very heavy, thick volumes, such as dictionaries, should have all the strengthening devices and especially should have the bands and canton flannel on the back placed in split boards or between two boards glued together. It is impossible to bind such books too strongly. In rare cases it may be well to sew heavy books constantly used on raised bands, to have leather corners, and a strip of leather along the bottom of each board.
LAW BOOKS
Some of the professions have conventional ways of binding professional books. In the law, for example, it was formerly customary to bind all law books in full sheep of the natural color. When sheep fell into disrepute, the law publishers began to substitute cloth similar in shade to the sheep generally used--a decided gain for law libraries.
Supplement the general specifications by the following:
- End papers and fly-leaves must be guarded with jaconet, as described
in specifications for fiction and juvenile books, page 93.
- First and last sections must be guarded with jaconet.
- All maps and charts must be backed with muslin and not folded unless
necessary.
- (a) Bancroft Legal buckram (the lightest shade made), or Holliston
Mills Library buckram No. 32, should be used for covering.
(b) Books used constantly should be bound in half Turkey morocco or Niger morocco.
MUSIC
- The most essential quality of a well-bound book of music is its
ability to lie flat wherever opened. It is unwise therefore to use any kind of an overcast stitch in sewing. Regular sewing on tapes, instead of bands, must be used.
- The square at the bottom of the book should be greater than at the
top so that leaves will not catch on the music-rack when turned over.
- Imperial morocco cloth should be used for covering. If hard usage is
expected half cowhide, with sides of some kind of washable cloth, is preferable.
- Part music for various instruments or solos with accompaniment must
have one strong binding for the part which takes the most space, with pocket on the inside of the back cover to hold the other parts. If these are bulky compensating guards should be inserted in the back of the book.
BOOKS OF ILLUSTRATIONS
Every library finds it necessary to bind a few books, such as Racinet's "Le costume historique," which have very little text and a great number of illustrations. It is evident that the illustrations in such books are most useful if kept in unbound form in portfolios, but when kept in such a way they are likely to be lost, torn, mutilated or misplaced.
- Each plate should be guarded with thin, tough paper and the guards
overcast.
This insures a good strong sewing; in addition the guard forms a hinge where it meets the plate and the plate will lie flat and can easily be examined when the book is opened.
- Because of the artistic nature of such books, they should be bound in
one-half morocco, taking extra care to see that acid-free leather is used.
- Canton flannel and bands, or tapes, should be inserted between split
boards. If the book is very heavy, it would be wise to line the back with duck or a flesher rather than with canton flannel.
COMMERCIAL BINDING FOR REFERENCE BOOKS
While they are not a part of library binding, it may not be amiss to include specifications for commercial binding of heavy reference books, such as dictionaries, cyclopedias, etc. It is done with the hope that librarians will exert pressure upon the publishers to induce them to adopt these or other specifications which will produce equally good results.
- Four tapes should be used in sewing; the tapes must extend on each
side of the book at least two inches. The book should contain as many stitches as possible, using the best four-strand cotton thread. The thickness of the thread will depend somewhat upon the number of pages in a signature. Books should be sewed "all along" with no splitting of signatures at head or tail.
- First and last signatures should be reinforced inside and outside of
the fold with a strip of strong, thin muslin which passes around the outside of the end papers. The English cloth called jaconet is the best for this purpose.
- The second signature and the next to the last should be reinforced
with muslin on the inside of the fold.
- The end papers should also be lined on the inside.
- Illustrations should be guarded with muslin which is folded around
the next signature.
- Books should be lined with a medium grade of canton flannel, with the
fuzzy side to the back and extending from one-half inch from the head to within one-half inch of the tail of the book, lapping over at least two inches on the side.
- The flannel, together with the tapes, should be inserted between
split boards.
- Over the canton flannel, but not extending over to the sides, there
should be pasted a good quality of linen, rope or manila paper of sufficient thickness to make the book firm. In putting on this lining paper paste instead of glue must be used.
- Volumes should have French joints.
- The best quality millboard of suitable thickness with rounded
corners should be used.
- Leather should be made, if possible, according to the specifications
of the London Society of Arts. Niger morocco is probably the best.
Volumes should have leather corners as well as backs.
- For cloth sides, Winterbottom's Imperial morocco cloth, Bancroft's
Legal buckram, or Holliston's Library buckram should be used.
CHAPTER VI
BINDING BEFORE PURCHASE AND REINFORCING
One way of economizing in libraries is to buy books that have been bound in strong binding before they come to the library. It is not, however, a universal panacea which will reduce binding bills to a minimum. On the contrary, if not used with caution, this plan will result in the expenditure of large sums of money for which the library will never receive a return in actual wear of the books. Library binders who adopt this scheme buy books in the sheets from the publishers, put them into a strong binding and sell them directly to the library. Mr. Cedric Chivers of Bath, England, was the first to adopt this plan.
Later he started a bindery in this country, and since then other binders have followed his practice. For the librarian there are several advantages in this method of buying books.
- Books can be bound according to the library's special needs before
they have received any wear, while the paper is fresh and clean. Books printed on very thick, spongy paper must be sewed very strongly and receive special reinforcements that are not necessary on paper which is more suitable for binding. If a good library binder buys the sheets from the publishers, he can test the paper to see what kind of treatment it should receive, and he can then bind it suitably for library wear. If the book is used in the original publishers' binding it deteriorates much more rapidly than when properly bound at the beginning.
- The book can remain in circulation at the time when it is most
needed. Formerly one of the greatest trials in public libraries was the necessity of withdrawing from the shelves practically all the copies of a popular novel in order to send them to the bindery where they remained from four to six weeks, the public meanwhile hurling anathemas at the librarian for not providing sufficient copies of the book.
Not only were the books out of circulation when most needed, but much time was used in preparing them for the bindery, checking them up on return, putting on the library marks of ownership, making cards, marking pockets, etc., all of which added to the expense. Today, in the case of new novels which are sure to be popular, such troubles are unnecessary.
Instead of buying the original publishers' binding, the wise librarian buys a sufficient number of copies bound from the sheets; if the binding is properly done, he need pay no more attention to them until they are worn out. He has done what he could to prevent the public from becoming dissatisfied, and he has saved the cost of the work required to send them to the bindery.
- Not only has he served his public better and saved the time of
assistants, but in most cases he has actually saved money on his binding bills. Let us suppose that he pays $1.50 for a book bound from the sheets; and suppose that he also buys a copy of the same book in the publisher's cover at a cost of $1.22, which, after it has been issued twenty times, has to be bound at a cost of 50 cents, making a total cost of $1.72. If they are issued the same number of times there is a clear saving of 22 cents in favor of the book bound from the sheets.
As a matter of fact, however, statistics kept by the Wilmington Institute Free Library indicate that the first book will be issued 125 times before it is discarded, and the second 100 times--twenty before binding and eighty afterward. If this be true, it is clear that there is a further saving, provided that both have to be replaced when finally worn out.
While these advantages are well worth considering, the librarian should not necessarily get all his books in this form. It is a plan which is peculiarly advantageous in the case of fiction and those few other books which are in constant use. In the case of juvenile books one must be cautious. Juvenile books, particularly books for boys, become soiled so much more quickly than the adult books that they frequently have to be discarded because they are dirty rather than because they are worn out.
If the books were bound before purchase the library may have lost money, because one can frequently buy a publisher's book and rebind it more cheaply than he can purchase the book bound from the sheets.
Most books in the classes should be purchased in the regular publisher's binding unless they are constantly used. In other words, the use a book is to receive is the test of whether it should be bound from the sheets before purchase. Having decided that the use of a book warrants binding from the sheets, it is well to consider other facts.
- It may not always be wise to bind from the sheets all the copies of a
new book by a well-known author whose works are always popular and likely to continue so for years. If ten copies are approximately sufficient for use during the first year, it is safe to say that in most cases they will be too many for the needs of the library during the second and third years. If they are bound in leather before purchase they will not wear out and during the third and succeeding years a number of them may be deadwood on the shelves. It is therefore wiser to buy a few copies in leather binding and the others either in a regular publishers' binding, or in some publisher's cover reinforced.
When these volumes have come to the point where they need binding the period of greatest popularity may have passed and they may be withdrawn, thus saving the library the expense of binding.
- When the book is finally worn out and must be withdrawn from
circulation, the question always arises, must it be replaced with a new copy? The majority of fiction and juvenile books so replaced are books of wide popularity. Occasionally a book, such as Henry James' "Princess Casamassima," or W. D. Howells' "Modern instance," is replaced because the library must have it on the shelves, not because it is popular. But ordinarily the popularity of a book is the determining factor in replacing worn-out copies. The decision to replace carries with it the decision to keep a book on the shelves indefinitely.
Since the book has proved its worth and is to receive hard wear, the reasons which prevailed against buying it in a strong binding when it was new no longer exist. The strongest binding that can be obtained suited to the strength of the paper is none too strong.
Perhaps the most vehement objection to books bound from the sheets comes from those librarians who have a strong sense of aesthetic values and who claim that these books are not so attractive to the eyes as the regular books in their bright and gay publishers' covers. The objection is valid. It must be admitted that the leather-covered books have the appearance of strength and serviceability, but not of beauty.
If a reader knows that he wishes a particular book, he will not be prevented from taking it because of its appearance, but if it is bound in leather and he knows nothing about it, he will very likely pass it over and select some book which has a bright, attractive cover. This is true even of adults, while of children it is doubly true. A large part of the popularity of that well-known book, "Fighting a fire," is due to the attractive cover which almost always excites the interest of boys who happen to see it.
Although the first cost of books bound from the sheets is always greater than that of books in the regular publishers' covers, it is hoped that the economy of buying them under certain conditions has been made clear.
There is, however, a cheaper way of buying some books which one would otherwise obtain in this form. Every year many copies of popular fiction and juvenile books find their way to the shelves of second-hand book dealers. Some of these copies show signs of wear, while some of them are in excellent condition. In any event it is always wise to submit a list of replacements to some large dealer in second-hand books; to buy such books as may be obtained from him (generally at considerably less than one-half the published price); and to send them at once to a good library binder for rebinding before placing upon the shelves of the library.
In this way one should get from 25 per cent to 33-1/3 per cent of fiction replacements in a substantial binding at a cost much less than the cost of a book in the original publishers' binding.
REINFORCED BOOKS
For those who wish strong bindings, but who wish them attractive also, reinforced bindings can be recommended. Reinforced books are those which have been strengthened either by the publishers in the regular course of manufacture, or by some binder who takes the book as it comes from the publisher, removes the cover, strengthens the book and puts it back into the same cover. A reinforced book generally appears in the attractive publisher's cover, and it always appears in some form of cloth, never in leather.
Owing to the small number of times which books in the original publishers' binding were issued, the committee on binding of the American Library Association made an effort in 1906 to induce the publishers to issue a special edition for library use. As it was recognized that the publishers would not take kindly to elaborate specifications for stronger bindings, the improvements asked for were made as few in number as possible. They were the following:
- Sewed on three tapes (very small books sewed on two tapes).
- First and last signatures reinforced with muslin.
- Cloth strip in joints pasted on fly leaf and sewed through.
- Thin strong muslin over backs.
An attempt to demand hand-sewed books was abandoned when it was discovered that this stipulation added greatly to the cost of the binding without noticeably increasing its strength. The main strength of a book bound according to these specifications lay in the guarding of the first and last signatures.
The honor of issuing the first reinforced book for library use belongs to Charles Scribner's Sons Co., who in the summer of 1906 bound 1500 copies of F. Hopkinson Smith's "Tides of Barnegat." Their specifications, based on those submitted by the A. L. A. committee on binding, required that:
- Signatures contain not more than sixteen pages;
- First and last signatures be guarded with muslin before sewing;
- First and last signatures be oversewed (actually they were run
through a sewing machine);
- Lining papers be guarded with strong drill and sewed through;
- The book be sewed on two tapes;
- Highest grade super be used for back-lining;
- Books be glued to the back of the cover; making a tight back book;
- Buckram be used for the covers instead of the regular publisher's
cover.
The extra cost of the book was ten cents, and it was an excellent piece of work. In actual wear the books far exceeded the hopes of those who favored the plan, for they all went through the period of greatest popularity without being withdrawn from circulation. When they came to the point where they could no longer be circulated, most of them were discarded instead of being sent to the bindery.
The initial success of the plan induced other publishers to try the experiment. In 1908 one hundred and twenty different books could be obtained in reinforced bindings from seventeen publishers. Among these publishers were the firms of Century Company, Harper, Houghton, Little Brown & Company, McClurg, Putnam, Scribner's, Stokes, and Warne. Some of these books were well-bound, the publishers evidently making a conscientious effort to meet the demands of the committee; others were makeshifts not worth one-half the extra cost.
The success of "Tides of Barnegat" encouraged Charles Scribner's Sons to give the experiment further trial, and from time to time during a period of several months this firm issued books bound in this way. In no case, however, was the initial success repeated. After the experiments had been tried by the different publishers for several months the obstacles to the plan, several of which had been foreseen, grew greater rather than less, and in the end the publishers gave up the plan of providing special editions of new fiction and juvenile books for library use.
The main obstacle to the successful culmination of the plan lay in the inability of librarians to order books before publication, and in the inability of publishers to make special editions after the book had been published. The success of "Tides of Barnegat" was due largely to the fact that the author and book were well known in advance of publication.
Librarians knew at once that they wanted the book and the orders were filed promptly. In the case of nearly every other book which Scribner published in this way librarians could not decide until they had actually seen the book, or at least had seen reviews of it. Quite naturally they sent in few orders for the books. On the other hand Scribner did not care to bind a large number of books in special binding unless they had some assurance that the books would be sold; and they could not at any time afford to manufacture a very small number. It seemed impossible to bridge this gap which existed between the publisher and the librarian.
Other reasons which worked against the success of the plan were:
(a) The apathy of the library world in general. In spite of efforts made both by publishers and by those librarians specially interested; in spite of the proved success and economy of the best reinforced bindings, librarians in general paid little attention to them.
(b) The opposition of booksellers. This opposition was not violent at any time; but a special edition for one class of buyers inevitably entailed more labor upon jobbers and booksellers with no financial return, since there was no discount on the 10c. extra cost. It followed that orders from librarians for the special library editions were filled by some jobbers with regular editions; and the time required to exchange the copy of a regular edition for one of a special edition was generally sufficient to prevent the librarian from returning the books. Had it been possible to have one central bureau to bunch orders and to distribute them, greater success might have resulted.
While the effort to induce publishers to issue special library editions and to keep them in stock was a failure, there were nevertheless good results from the venture. While most of the commercial bindings are no better to-day than they were ten years ago, yet the publishers know that something better is needed for library use. Small books which are used by children and receive hard usage are as a rule much stronger bound than formerly, and will last as long as they are needed. As one direct result of the agitation, the well-known Everyman's set can now be obtained in a library binding. Certain large reference books, such as Webster's and the Century dictionaries, U. S.
Catalog, etc., have been put into the strongest possible binding. In these cases the publishers have tried to meet the demands of librarians.
When the publishers ceased to make special editions for libraries several library binders undertook to supply books in this form. Their method was to buy the books from the publishers, remove the covers, resew the books in the most approved library style and replace the books in the publisher's covers. When this cover wears out the sewing is so good that it is only necessary to recover either with a regular leather-back binder's cover, or with a home-made cloth cover.
By this method the librarian is assured of a book in the same cover as the regular edition, the necessity of sending orders in advance of publication is obviated, and the publishers, jobbers and booksellers do not have to keep a stock of a special edition. In practice the plan works well.
Librarians for years have been annoyed because certain books, such as the Brownie books, have given such poor service no matter how they were bound. In the original boards they went to pieces very quickly and the paper was of such a character that they were hard to rebind. The strong leather bindings bound from the sheets were too strong because the paper wore out long before the binding. In 1912 books of this character, through the initiative of Mr. H. R.
Huntting in Springfield, Massachusetts, were sewed by the Samson-back method, a strong machine sewing; they were then covered with cloth and the paper covers, so attractive to children, pasted on the outside. The cost of the books was much less than that of the leather-back binding and they were much more attractive. The Samson-back method of reinforcement therefore practically solved the problem of binding large thin books with wide margins at the back, precisely the books that had given librarians the most trouble.
CHAPTER VII
COST
Binding is a work of repair, not one of expansion, and consequently the amount spent for this purpose adds little to the resources of the library. The modern librarian does not begrudge money for salaries; heat, light and the general up-keep are items that cannot be reduced materially in most libraries. But money spent on binding reduces the funds available for new books. Therefore, a study of the many ways in which binding bills can be made smaller is well worth while.
Two elements, material and labor, enter into the cost of binding, labor of course forming the larger part. Since the cost of labor varies in different parts of the United States, it is impossible to give figures of cost applicable to all places. Furthermore, as the cost of both material and labor is increasing constantly any statement made at the present time might be wrong a year from now.
So far as figures of cost are concerned, it therefore seems best to discuss maximum and minimum figures. On this basis it is fair to assume that it will not be necessary at any time in the near future to pay more than fifty cents a book for fiction and juvenile books eight inches or less in height, bound in cowhide, government cloth, or the more expensive imperial morocco cloth. For this amount the librarian should get the best binding obtainable. As high a price as this is actually charged by a few binders only, some of whom are justified in so doing because they give full value for the money, or because the cost of their labor is high.
If less than thirty-five cents is paid for fiction and juvenile books eight inches high, it is probable that the binding is not serviceable and therefore not economical; but in rare cases bindings costing thirty cents a volume will give excellent service. When low prices are charged the librarian should be sure that, taking the ratio of cost to circulation into consideration, he is getting full value. In general, it may be said that he who gets fiction and juvenile books well bound for less than forty cents a volume is to be congratulated.
Naturally, this statement does not apply to the large libraries which bind a large number of books every month, and can therefore obtain better rates than the smaller libraries.
For books bound in cowhide or cloth, the cost increases at the rate of from fifteen to twenty cents a volume for every two inches in height.
The price of the smallest volumes bound in morocco is considerably greater than of those bound in other materials, and the increase according to size is also somewhat greater. One dollar is the highest price paid within the knowledge of the writer for an eight-inch morocco book, and sixty cents the lowest price. The difference in the value of the work about corresponds to the difference in price.
Periodicals bound in government cloth, or duck, may cost from fifty-five cents to eighty cents a volume ten inches or less in height, increasing fifteen cents to twenty cents a volume for every two inches in height.
Newspapers well bound should not cost less than $2.00 a volume, nor over $4.00. More variations will be found in the prices for newspapers than in any other kind of binding.
Most binders are paid a certain amount for books eight inches high or less, the prices differing according to the material used. The price in a few cases increases with each inch or fraction thereof in height to ten inches; in most cases the increase is for each two inches or fraction. For example, a book which measures eight and one quarter inches in height is charged for at the ten inch rate. One which measures ten and one quarter inches at the twelve inch rate. Sometimes an extra charge for books which are much thicker than usual is justified.
The following schedule covers practically all the different sizes and materials which the librarian must take into consideration. The prices given are those actually charged by a good library binder.
REBINDING
Adult and Juvenile and Miscellaneous Books Not Exceeding 2 Inches in Thickness
8 in. 9 in. 10 in. 12 in.
Half Pigskin or Cowhide 45 55 65 85
Full Cloth (Library Buckram) 40 50 60 80
Full Imperial Morocco Cloth 45 55 65 85
Extra sizes
14 in. 16 in. per inch
Half Pigskin or Cowhide 1.10 1.30 20 cents
Full Cloth (Library Buckram) 1.00 1.20 15 cents
Full Imperial Morocco Cloth 1.10 1.30 20 cents
Books over 2 inches thick charged at rate of size above.
Magazines, Periodicals, Sheet and Folio Music Not Exceeding 4 Inches in Thickness
8 in. 9 in. 10 in. 12 in.
Full Cloth (Lib. Buck.) or Full Duck 45 55 65 85
Full Imperial Morocco Cloth 50 60 70 95
Half Cowhide 50 65 85 1.10
Half Pigskin (English) 55 70 90 1.15
Half Pigskin (American) 50 65 85 1.10
Half Morocco 65 80 1.00 1.25
Half Duck (Waterproof sides) 45 55 65 85
Extra sizes
14 in. 16 in. per inch
Full Cloth Lib. Buck. or Full Duck 1.10 1.35 15 cents
Full Imperial Morocco Cloth 1.20 1.45 20 cents
Half Cowhide 1.30 1.60 20 cents
Half Pigskin (English) 1.35 1.65 20 cents
Half Pigskin (American) 1.30 1.60 20 cents
Half Morocco 1.50 1.85 25 cents
Half Duck (Waterproof sides) 1.10 1.35 15 cents
Above prices include all lettering on books.
Books over 4 inches thick charged at rate of size larger.
Newspapers not over 30 inches, in half library buckram or half duck $2.25, or in full duck, $2.40.
Special prices for dictionaries, cyclopedias and other sizes not in above schedules.
SUGGESTIONS FOR REDUCING COST
Following is a statement of plans for cutting down the cost of binding, a few of them being obviously makeshifts for the benefit of poor or very small libraries.
BOOKS BOUND BEFORE PURCHASE
Under this head will be found (in Chapter 6) a full statement of reasons for buying books bound from the sheets.
REPRINTS BOUND BEFORE PURCHASE
The cheap reprints of popular novels which cost less than one-half as much as the original edition, although attractive in appearance, are very poorly bound and if bought in original covers must be rebound within a short time after they are first placed on the shelves. Some librarians find that it pays to send orders for books which can be obtained in cheap reprints directly to their binders, who buy the books and rebind them in the regular half-leather binding which the library uses for its rebound fiction and juvenile.
He bills the books to the library at the cost of the volume plus the cost of binding, the total in any event being considerably less than one dollar. Not over ninety cents should be paid and eighty-five cents is the general price for such books. In this way the library gets a book in a good, strong library binding for less than the cost of the original edition in publisher's cover. Furthermore all labor involved in sending the book to the bindery and receiving it again--no inconsiderable item--is eliminated.
SECOND-HAND BOOKS
Akin to the foregoing plan is the practice which some libraries have of sending lists of replacements to dealers in second-hand books and having all books obtained in this way rebound at once before putting them into circulation. Moreover this arrangement eliminates the time and labor necessary to send a book to the bindery. Binderies in large cities can undertake to supply second-hand books, with advantages both to themselves and to the libraries employing them.
The library is relieved from the necessity of searching for second-hand volumes, while the binder can well afford to do this service for a stated price per volume which will be reasonable from the library point of view, but which will allow the binder profit on all books which he can find at very cheap prices. When such a plan is adopted the binder should understand that the library wants neither the cheap books printed on wretched paper and having very small print, nor the very fine editions with colored illustrations.
REINFORCEMENTS
A reinforced book is one which has been removed from the original publisher's cover, strengthened in various ways and put back into the same cover. (See chapter on this subject, page 108.) In its best form it means the complete resewing of the book with an overcast stitch. It is advisable to buy such books frequently, since they preserve the attractive publisher's cover and since they can also be recovered by the library itself without resewing. Statistics kept by the Wilmington Institute Free Library show that such books when properly recovered give as good relative service as those which have been bound before purchase.
The main advantage lies in the elimination of the time necessary to send them to the bindery and the greater length of service which they give at the height of their popularity.
RECOVERING AT THE LIBRARY
Many books which come to the binding department require rebinding in order to put them into the best condition, but the books will be used so little that rebinding would not pay. In the numerous cases in which the sewing is in good condition it will be possible to recover them at the library and letter them by hand. In cases where the sewing is poor it will be possible to resew and recover.
Such books are neither so strong nor so attractive as books which have been wholly rebound, but they can be recovered at an expenditure of less than fifteen cents a volume, as against forty to fifty cents a volume for binding, and are in sufficiently good condition to wear a long time, perhaps as long as the library needs them. (For description of the process of recovering see page 185.)
DISCARDING VALUELESS BOOKS
In the preceding case it has been taken for granted that the books in question add something to the resources of the library and that they must be kept. Books that have outlived their usefulness because they have been superseded by later editions, or by other books more authoritative, in all except the largest libraries should be discarded. (For arguments in favor of this see Chapter 8, p. 131.)
LEATHER VS. CLOTH
Notwithstanding that he is repeating himself, the writer wishes to emphasize one point. It may almost be made a general rule, though like other rules, it will not work well at all times. Never bind a seldom used book in leather, or a much used one in cloth.
CHEAP EDITIONS
Money may be saved by replacing books which need rebinding with good editions cheaper than the cost of binding. (See (f), page 129.)
PROPER CARE
The life of the book in the library may be prolonged in several ways.
- In opening the leaves of uncut books at the top the paper knife
should be carried to the back of the book, using a dull knife that is thin, long and tapering.
- Many books should be carefully opened before being placed on the
shelves. This is done by resting the book on its back and dropping the covers on the table. Taking a few leaves at a time first at the front and then at the back, press them down carefully until the middle of the book is reached. If this be done there is little chance that the back of the book will be broken if the book is suddenly opened.
- Books should not be pressed tightly together on the shelves.
- They should not be piled on other books resting on their fore-edge.
- They should not be pulled from the shelves by the head bands.
- They should be dusted frequently.
- They should be kept upright on the shelves instead of half-fallen
over.
- In every way they should be handled as if they were books, not
bricks.
CHAPTER VIII
PREPARING FOR THE BINDERY
To decide properly what books should be rebound and how they should be rebound is not a simple matter nor one which should be left to an inexperienced or uneducated assistant. In addition to a good working knowledge of materials and processes the assistant in charge of this work should have a general knowledge of books--paper, editions, prices, literary value, timeliness, etc.--and good judgment in deciding whether a book should be bound or whether it should be mended, recased, wrapped in paper, recovered, or thrown away.
The binding, therefore, should be in the hands of an assistant who understands the demands of this department of library service, and for economy's sake as well as for the sake of efficiency it should not be shifted from one person to another.
Mr. Dana has shown in his "Notes on bookbinding for libraries" how essential it is that binding assistants should know books. Credit for much of what here appears in support of that viewpoint is due him and is herewith acknowledged.
In considering the binding of fiction and juvenile books the following are some of the questions which the binding assistant must ask and decide before determining whether a book is to go to the shelves in a new dress, or to the junk-man as waste paper:
(a) Is the book in such poor condition that it cannot be rebound or recased? If so, it must be discarded. While this decision is generally easy to make, it is sometimes made difficult by books which are in too good condition to throw away and in too poor condition to rebind. In such cases the decision must depend on the popularity of the book. If very popular, it may be wise to rebind it, for it must be remembered that good library binders can accomplish wonders with books that are in poor condition.
Sometimes the question arises whether the book is in poor enough condition to need rebinding. Perhaps it will survive a few more issues just as it stands. If the book is a trifle shaky in its covers, the decision should be to rebind. The binder can do a better job at this time than he can when the book becomes more worn, and the life of the book will be prolonged by prompt binding. If the assistant decides not to rebind it, the book will be issued only a few more times before it will have to be withdrawn from circulation and sent to the repair room again. The result is a greater loss of time with no actual gain in wear.
(b) Is the book much read? If it is an old one that is evidently popular, it is reasonable to suppose that it is the policy of the library to supply the demand for this book, and the book will be rebound as a matter of course. A decision about new books which are popular is harder to make because it is fair to ask:
(c) Is the demand falling off? It is here that the assistant must show good judgment. It may be that the book can be rebound easily with profit, if there is a sufficient demand to keep all the copies in circulation. It may be that the book is waning in popularity and that other copies in the library are ample to supply present demands. If they are, the copy in hand should be canceled, since the cost of binding will then be saved. But the assistant should ascertain the condition of the remaining copies.
Let us take the case of a novel which has been withdrawn from circulation because it needs rebinding. The assistant looks at the record of circulation on the book card or pocket and discovers that last year the book was issued four times a month, while now it is issued only twice a month. He finds also that there are four other copies. These four copies should be sufficient to meet present demands, and the book in hand may be withdrawn.
But suppose that further investigation shows that two of the four copies are in very poor condition and cannot be rebound. If he withdraws the one in hand, only two good copies will remain, and perhaps these are not sufficient to supply the demand. On the other hand, it is possible that they are sufficient to supply the demand. In any event, the situation is one which requires a knowledge of the book itself, its popularity with the public, and general good judgment. The question may be summed up in this way:
- It is cheaper to rebind a book than it is to discard it and later be
obliged to buy a new copy.
- It is cheaper to discard a book when it seems assured that the book's
popularity is over, than to bind it and have it remain for years unused.
(d) If the book is much used, is it a book that the library wishes to circulate? Every library has certain books on its shelves of which those in authority somewhat disapprove, but which are very popular and not poor enough to be done away with altogether. It is sometimes the policy to supply only partially the demand for such books; sometimes to discard them entirely when worn out. The good binding assistant will remember the titles of these books and use good judgment in dealing with them when they come into his hands.
(e) If the book is not much read, is it a standard work? For example, in the case of a work of Anthony Trollope the assistant discovers that it was issued only once during the last year and that it is the only copy in the library. If he does not "know books," he will be led to believe that the book has no value and will cancel it. In a large library an action of this sort would be unwise; in a small library the decision would depend upon the particular title.
Most libraries keep a book of this particular class in order to supply the occasional demand for it. There are many books not written by men with the reputation of Anthony Trollope which, nevertheless, have intrinsic worth and have a small circle of admirers. They may not have great merit, but on no account should the library be without them. As examples of books of this kind we may take Mrs. Brush's "Colonel's opera cloak" and Theodore Winthrop's "John Brent."
(f) Can the book be replaced with a good reprint which will wear as long as a new binding and cost less? While there are not many cases in which this can be done, the assistant should watch for them. The most noteworthy reprints which will meet these requirements are the volumes in Everyman's Library. In the original Everyman's edition these were entirely unsuited for library use, but in 1910 they were all put into a strong library binding. In the cloth edition they sell for thirty-five cents a volume and can easily be issued from forty to fifty times before being discarded. This makes the cost for each issue as small as can be obtained by binding higher-priced editions.
The following case, which actually happened, illustrates the point, although the books are not fiction. Grote's "History of Greece," in twelve volumes, was in bad condition; several of the cloth backs were torn and the sewing of all the volumes was loose. It was decided to send the books to be rebound at a cost of $5.40. Before doing so, the list of Everyman's Library was consulted and it was found that the work could be obtained in that form in twelve volumes at a cost of $4.20, a clear saving of $1.20, or over 20 per cent.
The work was seldom used, yet it was necessary to have the set on the shelves; the Everyman's edition answered every purpose, and will undoubtedly last as long as the rebound set would have done. Unfortunately, owing to copyright provisions, comparatively few of the books which are constantly wearing out can be obtained in this edition.
(g) Is it an old edition, with poor paper and poor type? A book of this sort should never be rebound but should be discarded and a new copy purchased even if the cost of a new copy be much greater than that of rebinding.
(h) If the book is the only copy in the library and is read not oftener than once in ten years, should it be kept because it is important historically? Good examples of this class of unused books are the works of Charles Brockden Brown. They are not interesting at the present time, but when first published were much read. Every student of American literature should read them, and they should be on the shelves of all except the small libraries. Here again good judgment is called for on the part of the assistant.
(i) Is the book used so seldom that it can be recased or recovered by the library? The process of recasing (described on page 184) can be used in the case of small-sized books which have covers showing little evidence of wear, and which do not receive hard usage. The process of recovering (described on page 185) can be used on leather-bound books which have cracked at the joints. In either case the sewing must be perfectly sound.
(j) Finally, let us suppose that we have asked all the foregoing questions and are still undecided what to do. There will be very few cases of the kind. Perhaps the best solution is to wrap the book in paper, letter it with author, title and call number, and transfer it from the fiction shelves to the regular literature shelves. It may stay there for years unused and yet be at hand when finally called for.
With books other than fiction and juvenile many of the same questions must be asked. In addition, however, it is sometimes necessary to ask the following:
(a) Are there later editions which are more valuable? This question will arise with frequency especially in the case of scientific, technical and reference books, and careful judgment must be exercised in making decisions. It often happens that a later edition of a technical book has little more value than the one which precedes it; frequently it entirely supersedes the earlier edition. In the one case the book can be rebound with profit, in the other it is best to discard it and buy the latest edition.
Some libraries keep all the editions of a book for historical purposes; but most libraries, especially the smaller ones, will do better to discard older editions when they are superseded by later ones. Sometimes a book has no later edition, but its place has been entirely taken by the work of other authors. In such cases it should be remembered that an out-of-date technical book in the hands of an inexperienced person frequently causes more harm than good.
It may cost more to buy a new book than to rebind an old one; yet this is exactly what should be done in every such case if the funds of the library permit.
(b) May not the library be better off without either the book or a substitute? In the past librarians have hesitated to discard any book which has once been placed on the shelves. They have believed that all printed matter has value and that a book which belongs to the library is sacred and must on no account be destroyed. It is difficult to defend such an attitude.
If we admit for the time being that the librarian never makes mistakes in acquiring books, still it is sure to happen that many books will outlive their usefulness, except as a part of the history or bibliography of the subject. Why should they be kept on the shelves when they are not used and ought not to be used? It cannot, of course, be admitted that the librarian makes no mistakes in acquiring books; every library in the country will show examples of poor selection. Why, after a mistake has been made, refuse to admit it?
If the original purchase (or acceptance of a gift) was a mistake, to keep the book on the shelves simply perpetuates the mistake and adds to the expense of maintenance. It is no crime to discard a book. On the contrary, in many cases, it is the only sensible thing to do. In doubtful cases, however, the book should be kept.
ARRANGEMENT
If the final decision is to bind the book the next step is to arrange the book in the way in which it should be bound. The question of collation is one on which there has been a difference of opinion. Some librarians have claimed that it is best to collate books at the library in order to prevent imperfect books being bound, since it is always disappointing to discover, after a book has been bound, that it is incomplete. In the great majority of cases, however, collation is a waste of time, since good binders refuse to bind imperfect volumes.
In the case of very valuable books, especially those with many plates, and even in the case of less valuable books which have many illustrations not paged-in, it may be best to collate at the library since it is obviously unfair to the binder to expect him to be responsible for anything except the main paging. Fiction or juvenile books may sometimes be bound when one or two pages are missing. Juvenile books, especially, often go to the bindery with missing pages.
Many times these missing pages are not especially important and in these cases it seems more economical to bind the book than to buy a new copy. If the number of missing pages is not too great they may be typewritten from other copies. Books other than fiction or juvenile should seldom be bound in an imperfect condition.
Another exception to the rule of sending books uncollated is in the case of popular periodicals, such as Scribner's, Harper's, Century, etc., where the library has only one copy which it binds. Since periodicals frequently become torn and mutilated and must be replaced it will save delay in having the volumes bound, if the collation is done at the library.
But while collation is generally unnecessary, arrangement in proper order is essential. In dealing with periodicals this is not always an easy task. They should first be examined to see that all the numbers are in hand, and that there is a title-page and an index. It would seem as if there were little chance to go astray in doing this, yet the vagaries of periodicals are innumerable and nothing must be taken for granted. If only five monthly numbers are found when there should be six to complete the volume, it is not best to conclude hastily that it is incomplete.
Sometimes the cover indicates that two numbers are published in one. If it is not so indicated one must look at the paging. If the paging is consecutive, and there is a title-page and index, it is safe to assume that the volume is complete, even if a number is apparently missing.
The general rule for arranging periodicals is: Place title page at the beginning, followed by table of contents, text, and index at the end.
Periodicals in English are generally easy to arrange, though even in this case one must know whether the periodical in hand is in the habit of publishing supplements which are paged separately, but which are called for by the table of contents. If such supplements are omitted the volume is incomplete. An example of a periodical of this class was the Annals of the American Academy of Political and Social Science, before it changed to its method of issuing each number as a separate volume.
Many volumes of English periodicals such as All the Year Round, Household Words, etc., have been bound without the Christmas supplements, which those periodicals always issued. A few periodicals in English have two or more sets of pagings either in each number, or in some of the numbers and not in others. When the numbers are taken apart and the proper pagings grouped together, the table of contents will generally indicate how these should be arranged. But if not, it is usually readily apparent which is the main paging and which the minor paging or pagings.
Though rarely found in periodicals printed in English, this exasperating condition of affairs frequently exists in foreign periodicals. The Germans are especially fond of printing several different parts in the same number. Frequently a long monograph will begin in the first number of a volume and extend through two or more volumes. When completed it may or may not have a special title-page and index of its own. Perhaps the table of contents of the last volume in which part of it has appeared will call for it as a supplement to that volume.
Perhaps it does not. In any event the paging must be removed from the first and succeeding volumes until the monograph is finally complete. If it is not called for by any regular title-page or table of contents, it may be bound separately. Sometimes a periodical will appear in two or more parts each month, each part covering some phase of the larger subject indicated by the general title of the periodical.
These parts will be paged separately and numbered differently but will have the same kind of cover, and care must be used to keep the proper parts together.
Peculiarities and irregularities of this sort make periodicals veritable puzzles, some of which it may take months to solve.
In arranging periodicals, front covers having a different color from the text must be kept to facilitate use.
Advertisements as a rule should not be bound. Since they are a part of the history of the times, it is desirable for a few of the largest libraries to bind the advertising pages of one or two numbers a year in each periodical. Other libraries should throw them away. It is not necessary to remove them entirely before sending the volumes to the bindery; tearing down two or three inches on pages which are to be discarded is sufficient indication to the binder that they are not to be bound.
Several magazines, such as McClure's and Everybody's, have, for several years, made a practice of leaving articles unfinished in the main paging and continuing them on advertising pages. This is an annoying practice since great care must be taken to see that all text matter is complete, even if it becomes necessary to bind all advertising pages.
Many periodicals, especially those of a scientific character, contain plates which are not paged-in. If these are scattered through the text they may be allowed to stay there, but if they are grouped together at the end of each number they should be placed together in proper order at the end of the complete volume.
The vagaries of periodical publishers are shown as much in the way in which they issue (or do not issue) title-pages and indexes as in any other way. The proper way, which is seldom done, is to issue both title-page and index in the last number of each volume. Some publishers issue them in the first number of the next volume; some at various times during the publication of the succeeding volume. Some publish a title-page at the beginning of the first number of a volume and an index when the spirit moves.
Some publish a title-page but no index or table of contents. Others publish a title-page and table of contents but do not send them unless requested to do so. Many publish neither title-page nor index, and perfectly reputable periodicals which have published these essential parts of a periodical for twenty years or more will suddenly cease publishing them. It is evident that title-pages and indexes are nuisances in preparing periodicals for the bindery.
The assistant in charge should keep a record showing (a) which publishers must be asked to send title-pages and indexes, and this should be done as soon as possible after the volumes are complete; (b) in which number of a periodical title-pages and indexes may be looked for if they come regularly; (c) which periodicals do not publish title-pages and indexes.
If lack of funds makes it impossible to bind periodicals and they must be wrapped in paper it is highly important that title-pages and indexes be included, since it may be impossible to obtain them when funds permit binding.
Changes in the size of periodicals are a cause of annoyance. The annoyance is not great when the change is from a large quarto to an octavo, for the cost of binding an octavo is considerably less than that of a quarto. Unfortunately, the present tendency is almost wholly the other way. Many periodicals, for years published in a comfortable octavo size have been changed to a much larger size. This in itself is exasperating, but in addition the publishers apparently make no effort to change the size with the beginning of a new volume, so that part of a volume will be of one size and part of another. In such cases the troubles of the binding assistant may be readily imagined.
While it is highly important to bind only complete volumes of periodicals, it is occasionally permissible to bind volumes with guards for missing numbers which may be inserted later if they are obtained.
This method makes it possible to put a volume into permanent form better suited for use than unbound numbers, and prevents further loss of numbers already in hand. It can be done only when the numbers are very thin, particularly in the case of newspapers.
Quite a number of periodicals have so few pages in each number that a complete volume makes a very thin book. In such cases it is best to bind two volumes in one at the cost of one.
Among other material which passes through the hands of a binding assistant are the annual reports of various organizations--religious, charitable, fraternal, governmental, etc. In large libraries these must be bound for permanent preservation. In small libraries the annual reports of all local organizations should be bound if funds permit, others wrapped in paper and lettered on the wrapper. Whether they are to be bound or wrapped in paper, they should be grouped by regular periods, preferably five or ten reports in a volume, according to size, following the decades or half decades.
INSTRUCTIONS TO THE BINDER
Having decided that the volume must be bound and having arranged it in its proper order, the next step is to indicate to the binder how it is to be bound and lettered. Various methods have been used to indicate style and lettering. Some libraries have an elaborate binding slip, giving on one side the different materials, colors, etc., and having the other divided into panels for lettering. A slip is made for each book and the binder follows it carefully. Some libraries arrange an arbitrary system with the binder making one letter or figure indicate much that otherwise would have to be written in full.
For example, "C" under such an arrangement might mean "Bind in one-half red cowhide with green cloth sides." Some librarians give a general blanket order to bind all fiction in one way and all juvenile books in another.
For most books in English, except periodicals, lettering need not be indicated on a binding slip. All that is necessary is to underscore lightly on the title page the first letter of words which must be used.
The call number may be put on a binding slip enclosed in the book, or in the case of fiction and juvenile books, it may be penciled lightly on the title page, thus doing away altogether with the binding slip. If there is a chance for misunderstanding on the part of the finisher, or if an author's real name must be used instead of a pseudonym which appears on the title page, a binding slip must be filled out giving exact lettering.
While exact lettering on a binding slip is not essential for ordinary books, it is necessary for periodicals, each set of which should be bound and lettered uniformly. This may be assured by making out a binding slip giving in full the title, dates covered, volume number and call number, if one is used. The slip goes to the bindery with the book, and when the volume is returned is filed so that when the next volume is to be bound the slip can be consulted and a new one written with the necessary changes in volume number and dates. The chief value of the slip is to show exactly how the previous volume has been bound, so that the following volumes can be made uniform if possible.
A carbon copy of binding slips for periodicals should be made, to be kept at the library for charging purposes.
When binding volumes which are a part of a set, other than a periodical, a slip must be made to be kept on file so that when another volume of the set comes to hand it will not be necessary to visit the shelves to see whether other volumes have been bound and how they have been bound.
In finishing periodicals the position of lettering and the size of type used may be kept uniform if the binder takes what is called a "rub" or "rub-off" of the book after it is lettered and keeps it on file at the bindery. This can easily be made by laying a sheet of thin, but tough, paper over the back and rubbing it with shoemaker's heel-ball which will show white lettering on a black background. When the next volume comes to the bindery the "rub-off" shows exact height of boards, exact position of lettering and size of type.
A few libraries have had a dummy back made for each periodical showing color and kind of material in addition to other details. But the cost of a dummy is not slight and a new one must be made whenever any change in title or size occurs. Large college or reference libraries may need dummy backs for their numerous sets of foreign periodicals having various marks, such as umlauts, etc., over or under letters. When a library operates its own bindery it is possible to send the last bound volume as a sample. While this adds much to the routine, its main advantage is that it eliminates the possibility of mistakes due to defective dummy or indistinct "rub-off."
LETTERING
It is necessary that binders understand exactly how books are to be lettered, what kind of type to use and the position on the back of the book which each item of information must have. There are differences of opinion as to the best ways of lettering, but it is essential that every librarian have uniformity in his own library, even if he disagrees with his fellow workers. In all lettering a bold, clear type should be used, and all figures should be in Arabic, since it is plainer than Roman.
In most leather bindings the back is divided into five or six panels, making it possible to obtain uniformity by setting aside each panel for a definite purpose. If desired, another narrow panel may be made in which to stamp a mark of ownership. Paneling is a useful device in the case of books which are eight inches or more in height, but in the case of juvenile books and fiction it may be omitted entirely. As most of these books require simply author, title and call number, if one be used, the device of paneling adds to the labor in binding and serves no useful purpose in the library. It should be used on most other books bound in leather and on all periodicals bound in cloth or duck.
Which shall go at the top of the book, author or title? In favor of the title it can be claimed that all publishers letter the title first with the author second; and since in non-fiction the books in publishers' covers on the shelves will outnumber the rebound books, it is advisable to put the title first in order to have uniformity. On the other hand, it can be claimed that the arrangement under the class is by author, that most library assistants look for the author rather than the title, and that it is therefore advisable to put the most important item of information at the top in the position of greatest prominence. In the opinion of the writer this advantage outweighs any other.
It may be assumed, therefore, that the best arrangement is author, title, volume number if necessary, and call number. In the case of fiction, juvenile books and all other books from which it seems desirable to omit panels, these items will be put on with sufficient space between to make them independent of each other. The bottom of the call number should be 1-1/4 or 1-1/2 inches from the tail of the book on all books in the library, except oversized books, which should have the call number at the top (Fig. 16). If panels are used, the author's name should be near the bottom of the first panel, the title in the second, volume number in the fourth and call number in the fifth (Fig. 15).
If two books are bound together, letter, author and title of the second book in the third panel (Fig. 17).
When a work is in more than one volume with separate titles for each volume, place the author's name in the first panel, general title in the second, volume in the third and the title of the particular volume in the fourth (Fig. 18).
If six panels are used, each item is dropped one panel.
In most cases the author's last name is sufficient, but occasionally it may be necessary to use initials to distinguish between authors having the same name. Use both surnames of joint authors (Fig. 19). For pseudonyms use the form adopted by the cataloging department. For example, if the catalog entry is under Clemens instead of Twain, letter Clemens on the book. Both real name and pseudonym may be put on the back, but it does not seem necessary. In the case of the classics add the name of translator or editor in the panel under the title (Fig. 20).
+------------+ +------------+ +------------+ +------------+
| | | 914.5 | | | | |
| Beecher | | qJ 23 | | Patton | | Bancroft |
| | | James | | | | |
+------------+ +------------+ +------------+ +------------+
| | | | | Home | | |
| Sermons | | Italian | | And School | | Works |
| | | Hours | | Sewing | | |
+------------+ +------------+ +------------+ +------------+
| | | | | Rarer | | |
| | | | | Hot Weather| | 30 |
| | | | | Dishes | | |
+------------+ +------------+ +------------+ +------------+
| | | | | | | |
| 1 | | | | | | Oregon |
| | | | | | | 2 |
+------------+ +------------+ +------------+ +------------+
| | | | | | | |
| 252 | | | | 641 | | 979.5 |
| B 398 | | | | R 694 | | B 22 |
+------------+ +------------+ +------------+ +------------+
| | | | | | | |
+------------+ +------------+ +------------+ +------------+
Fig. 15 Fig. 16 Fig. 17 Fig. 18
+------------+ +------------+ +------------+ +------------+
| Kipling | | | | National | | |
| Balestier | | Plato | | Conference | | |
| | | | | on City | | |
| | | | | Planning | | |
+------------+ +------------+ +------------+ +------------+
| | | | | | | Nineteenth |
| Naulahka | | Dialogues | |Proceedings | | Century |
| | | | | | | |
+------------+ +------------+ +------------+ +------------+
| | | | | | | |
| | | Jowett | | 1 | | |
| | | | | | | |
+------------+ +------------+ +------------+ +------------+
| | | | | | | |
| | | 1 | | Chicago | | |
| | | | | | | |
+------------+ +------------+ +------------+ +------------+
| | | | | | | Jan.-June |
| | | 888 | | 352 | | 1894 |
| K 575 | | P 69 | | N 23 | | 35 |
+------------+ +------------+ +------------+ +------------+
| | | | | | | |
+------------+ +------------+ +------------+ +------------+
Fig. 19 Fig. 20 Fig. 21 Fig. 22
+------------+ +------------+ +------------+ +------------+
| | | | | | | |
| Nature | | | | | | |
| | | | | | | |
|------------| |------------| |------------| |------------|
| | | National | | Littel's | | |
| | | Municipal | | Living | |Independent |
| | | Review | | Age | | |
|------------| |------------| |------------| |------------|
| Nov. 1895 | | | | | | |
| Apr.
1896 | | | | | | |
| 53 | | | | | |------------|
|------------| |------------| |------------| | Apr.-June |
| | | | | July-Sep. | | 1903 |
| | | 1913 | | 1888 | | 55 |
| | | 2 | | 178 | | Part 2 |
|------------| |------------| |------------| |------------|
| | | | | | | |
| | | | | Series 5 | | |
| | | | | 63 | | |
|------------| |------------| |------------| |------------|
| | | | | | | |
+------------+ +------------+ +------------+ +------------+
Fig. 23 Fig. 24 Fig. 25 Fig. 26
+------------+ +------+ +------------+ +------------+
| | | | | | | |
| | | | | | | |
| | |Griggs| | | | |
|------------| | | |------------| |------------|
| | | Use | | Harper's | | |
| Punch | | of | | Magazine | | Monist |
| | | the | | | | |
|------------| |Margin| |------------| |------------|
| | | | | | | |
| | |170-G | | | | |
| | | | | | | |
|------------| | 87 | |------------| |------------|
| | | | | | | |
| 1882 | | | | Index | | 1908 |
| 82-83 | | | | 1-40 | | 18 |
|------------| | | |------------| |------------|
| | | | | | | |
| | | | | | | Index |
| | | | | | | 1-17 |
|------------| | | |------------| |------------|
| | | | | | | |
+------------+ +------+ +------------+ +------------+
Fig. 27 Fig. 28 Fig. 29 Fig. 30
When the names of foreign cities or countries must be placed in the author panel, use the English form. Names of government departments, bureaus, etc., should be inverted if necessary to bring the distinctive word first. For example, use Health bureau, not Bureau of health.
In lettering titles it is seldom desirable to omit the first part of the title in order to use words which are more distinctive, in other words, to use a binder's title. If it is necessary it should be done with care and discrimination. Ordinarily, give first words, omitting articles.
Very long titles must be condensed, sometimes at the expense of clearness.
Proceedings of organizations which meet in different cities should have the name of the place of the meeting lettered in the third panel (Fig. 21).
On periodicals, the author panel is left vacant and the title of the periodical given in full in the second panel. Here it is never permissible to omit first words, except articles. Letter "American review of reviews," not "Review of reviews." In case of foreign periodicals it may be necessary to place a sub-title in the third panel when a periodical is issued in two or more parts and each part bound separately with a distinct title page. With this exception, leave the third panel vacant and letter date and volume number in the fourth panel.
Place first the months covered by the volume, followed by the year (Figs. 22 and 23.) Use the first three letters of each month, except June and July, which should be given in full. On foreign periodicals use the English abbreviations for months. If the volume covers the calendar year the months may be omitted (Fig. 24). In the same panel place the volume number beneath the year.
If the periodical has more than one series give dates and total volume number, placing underneath the series number and volume of series (Fig 25).
If the unbound volume of a periodical is too large to be bound in one book, bind it in two volumes and letter the exact months in each part, placing "Part 1" and "Part 2" underneath the volume number (Fig. 26).
If two volumes are bound in one give the inclusive volume numbers (Fig. 27).
In the case of periodicals having more than one series and which are indexed in Poole's index or the Readers' guide, the volume number given first should correspond with the one given in the indexes.
Thin volumes must be lettered lengthwise in the same order as outlined above. Always le
Edition notice Project Gutenberg source, credits & licence
The reading text above is the public-domain work. The Project Gutenberg header, production credits and licence are kept here as provenance rather than shown before the book.
Transcriber and production notes
Produced by Hazel Batey and the Online Distributed Proofreading Team at https://www.pgdp.net (This file was produced from images generously made available by The Internet Archive/American Libraries.)
Front matter as received (title page, contents)
LIBRARY BOOKBINDING
Library Bookbinding
by Arthur L. Bailey
_Librarian Wilmington_ (_Delaware_) _Institute Free Library_
Illustration
THE H. W. WILSON COMPANY
White Plains, N. Y., and New York City
1916
Published May, 1916
Copyright, 1916
By The H. W. Wilson CompanyHeader as received
The Project Gutenberg eBook of Library Bookbinding
This eBook is for the use of anyone anywhere in the United States and
most other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg License included with this eBook or online
at www.gutenberg.org. If you are not located in the United States,
you will have to check the laws of the country where you are located
before using this eBook.
Title: Library Bookbinding
Author: Arthur Low Bailey
Release date: December 22, 2011 [eBook #38387]
Most recently updated: January 8, 2021
Language: English
Other information and formats: www.gutenberg.org/ebooks/38387
Credits: Produced by Hazel Batey and the Online Distributed
Proofreading Team at https://www.pgdp.net (This file was
produced from images generously made available by The
Internet Archive/American Libraries.)Full Project Gutenberg licence
Updated editions will replace the previous one—the old editions will
be renamed.
Creating the works from print editions not protected by U.S. copyright
law means that no one owns a United States copyright in these works,
so the Foundation (and you!) can copy and distribute it in the United
States without permission and without paying copyright
royalties. Special rules, set forth in the General Terms of Use part
of this license, apply to copying and distributing Project
Gutenberg™ electronic works to protect the PROJECT GUTENBERG™
concept and trademark. Project Gutenberg is a registered trademark,
and may not be used if you charge for an eBook, except by following
the terms of the trademark license, including paying royalties for use
of the Project Gutenberg trademark. If you do not charge anything for
copies of this eBook, complying with the trademark license is very
easy. You may use this eBook for nearly any purpose such as creation
of derivative works, reports, performances and research. Project
Gutenberg eBooks may be modified and printed and given away—you may
do practically ANYTHING in the United States with eBooks not protected
by U.S. copyright law. Redistribution is subject to the trademark
license, especially commercial redistribution.
START: FULL LICENSE
THE FULL PROJECT GUTENBERG™ LICENSE
PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK
To protect the Project Gutenberg™ mission of promoting the free
distribution of electronic works, by using or distributing this work
(or any other work associated in any way with the phrase “Project
Gutenberg”), you agree to comply with all the terms of the Full
Project Gutenberg License available with this file or online at
www.gutenberg.org/license.
Section 1. General Terms of Use and Redistributing Project Gutenberg
electronic works
1.A. By reading or using any part of this Project Gutenberg
electronic work, you indicate that you have read, understand, agree to
and accept all the terms of this license and intellectual property
(trademark/copyright) agreement. If you do not agree to abide by all
the terms of this agreement, you must cease using and return or
destroy all copies of Project Gutenberg electronic works in your
possession. If you paid a fee for obtaining a copy of or access to a
Project Gutenberg electronic work and you do not agree to be bound
by the terms of this agreement, you may obtain a refund from the person
or entity to whom you paid the fee as set forth in paragraph 1.E.8.
1.B. “Project Gutenberg” is a registered trademark. It may only be
used on or associated in any way with an electronic work by people who
agree to be bound by the terms of this agreement. There are a few
things that you can do with most Project Gutenberg electronic works
even without complying with the full terms of this agreement. See
paragraph 1.C below. There are a lot of things you can do with Project
Gutenberg electronic works if you follow the terms of this
agreement and help preserve free future access to Project Gutenberg
electronic works. See paragraph 1.E below.
1.C. The Project Gutenberg Literary Archive Foundation (“the
Foundation” or PGLAF), owns a compilation copyright in the collection
of Project Gutenberg electronic works. Nearly all the individual
works in the collection are in the public domain in the United
States. If an individual work is unprotected by copyright law in the
United States and you are located in the United States, we do not
claim a right to prevent you from copying, distributing, performing,
displaying or creating derivative works based on the work as long as
all references to Project Gutenberg are removed. Of course, we hope
that you will support the Project Gutenberg mission of promoting
free access to electronic works by freely sharing Project Gutenberg
works in compliance with the terms of this agreement for keeping the
Project Gutenberg name associated with the work. You can easily
comply with the terms of this agreement by keeping this work in the
same format with its attached full Project Gutenberg License when
you share it without charge with others.
1.D. The copyright laws of the place where you are located also govern
what you can do with this work. Copyright laws in most countries are
in a constant state of change. If you are outside the United States,
check the laws of your country in addition to the terms of this
agreement before downloading, copying, displaying, performing,
distributing or creating derivative works based on this work or any
other Project Gutenberg work. The Foundation makes no
representations concerning the copyright status of any work in any
country other than the United States.
1.E. Unless you have removed all references to Project Gutenberg:
1.E.1. The following sentence, with active links to, or other
immediate access to, the full Project Gutenberg License must appear
prominently whenever any copy of a Project Gutenberg work (any work
on which the phrase “Project Gutenberg” appears, or with which the
phrase “Project Gutenberg” is associated) is accessed, displayed,
performed, viewed, copied or distributed:
This eBook is for the use of anyone anywhere in the United States and most
other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg™ License included with this eBook or online
at www.gutenberg.org. If you
are not located in the United States, you will have to check the laws
of the country where you are located before using this eBook.
1.E.2. If an individual Project Gutenberg electronic work is
derived from texts not protected by U.S. copyright law (does not
contain a notice indicating that it is posted with permission of the
copyright holder), the work can be copied and distributed to anyone in
the United States without paying any fees or charges. If you are
redistributing or providing access to a work with the phrase “Project
Gutenberg” associated with or appearing on the work, you must comply
either with the requirements of paragraphs 1.E.1 through 1.E.7 or
obtain permission for the use of the work and the Project Gutenberg
trademark as set forth in paragraphs 1.E.8 or 1.E.9.
1.E.3. If an individual Project Gutenberg electronic work is posted
with the permission of the copyright holder, your use and distribution
must comply with both paragraphs 1.E.1 through 1.E.7 and any
additional terms imposed by the copyright holder. Additional terms
will be linked to the Project Gutenberg License for all works
posted with the permission of the copyright holder found at the
beginning of this work.
1.E.4. Do not unlink or detach or remove the full Project Gutenberg
License terms from this work, or any files containing a part of this
work or any other work associated with Project Gutenberg.
1.E.5. Do not copy, display, perform, distribute or redistribute this
electronic work, or any part of this electronic work, without
prominently displaying the sentence set forth in paragraph 1.E.1 with
active links or immediate access to the full terms of the Project
Gutenberg License.
1.E.6. You may convert to and distribute this work in any binary,
compressed, marked up, nonproprietary or proprietary form, including
any word processing or hypertext form. However, if you provide access
to or distribute copies of a Project Gutenberg work in a format
other than “Plain Vanilla ASCII” or other format used in the official
version posted on the official Project Gutenberg website
(www.gutenberg.org), you must, at no additional cost, fee or expense
to the user, provide a copy, a means of exporting a copy, or a means
of obtaining a copy upon request, of the work in its original “Plain
Vanilla ASCII” or other form. Any alternate format must include the
full Project Gutenberg License as specified in paragraph 1.E.1.
1.E.7. Do not charge a fee for access to, viewing, displaying,
performing, copying or distributing any Project Gutenberg works
unless you comply with paragraph 1.E.8 or 1.E.9.
1.E.8. You may charge a reasonable fee for copies of or providing
access to or distributing Project Gutenberg electronic works
provided that:
• You pay a royalty fee of 20% of the gross profits you derive from
the use of Project Gutenberg works calculated using the method
you already use to calculate your applicable taxes. The fee is owed
to the owner of the Project Gutenberg trademark, but he has
agreed to donate royalties under this paragraph to the Project
Gutenberg Literary Archive Foundation. Royalty payments must be paid
within 60 days following each date on which you prepare (or are
legally required to prepare) your periodic tax returns. Royalty
payments should be clearly marked as such and sent to the Project
Gutenberg Literary Archive Foundation at the address specified in
Section 4, “Information about donations to the Project Gutenberg
Literary Archive Foundation.”
• You provide a full refund of any money paid by a user who notifies
you in writing (or by e-mail) within 30 days of receipt that s/he
does not agree to the terms of the full Project Gutenberg™
License. You must require such a user to return or destroy all
copies of the works possessed in a physical medium and discontinue
all use of and all access to other copies of Project Gutenberg™
works.
• You provide, in accordance with paragraph 1.F.3, a full refund of
any money paid for a work or a replacement copy, if a defect in the
electronic work is discovered and reported to you within 90 days of
receipt of the work.
• You comply with all other terms of this agreement for free
distribution of Project Gutenberg™ works.
1.E.9. If you wish to charge a fee or distribute a Project
Gutenberg™ electronic work or group of works on different terms than
are set forth in this agreement, you must obtain permission in writing
from the Project Gutenberg Literary Archive Foundation, the manager of
the Project Gutenberg™ trademark. Contact the Foundation as set
forth in Section 3 below.
1.F.
1.F.1. Project Gutenberg volunteers and employees expend considerable
effort to identify, do copyright research on, transcribe and proofread
works not protected by U.S. copyright law in creating the Project
Gutenberg™ collection. Despite these efforts, Project Gutenberg™
electronic works, and the medium on which they may be stored, may
contain “Defects,” such as, but not limited to, incomplete, inaccurate
or corrupt data, transcription errors, a copyright or other
intellectual property infringement, a defective or damaged disk or
other medium, a computer virus, or computer codes that damage or
cannot be read by your equipment.
1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right
of Replacement or Refund” described in paragraph 1.F.3, the Project
Gutenberg Literary Archive Foundation, the owner of the Project
Gutenberg™ trademark, and any other party distributing a Project
Gutenberg™ electronic work under this agreement, disclaim all
liability to you for damages, costs and expenses, including legal
fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGE.
1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
defect in this electronic work within 90 days of receiving it, you can
receive a refund of the money (if any) you paid for it by sending a
written explanation to the person you received the work from. If you
received the work on a physical medium, you must return the medium
with your written explanation. The person or entity that provided you
with the defective work may elect to provide a replacement copy in
lieu of a refund. If you received the work electronically, the person
or entity providing it to you may choose to give you a second
opportunity to receive the work electronically in lieu of a refund. If
the second copy is also defective, you may demand a refund in writing
without further opportunities to fix the problem.
1.F.4. Except for the limited right of replacement or refund set forth
in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO
OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
1.F.5. Some states do not allow disclaimers of certain implied
warranties or the exclusion or limitation of certain types of
damages. If any disclaimer or limitation set forth in this agreement
violates the law of the state applicable to this agreement, the
agreement shall be interpreted to make the maximum disclaimer or
limitation permitted by the applicable state law. The invalidity or
unenforceability of any provision of this agreement shall not void the
remaining provisions.
1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
trademark owner, any agent or employee of the Foundation, anyone
providing copies of Project Gutenberg™ electronic works in
accordance with this agreement, and any volunteers associated with the
production, promotion and distribution of Project Gutenberg™
electronic works, harmless from all liability, costs and expenses,
including legal fees, that arise directly or indirectly from any of
the following which you do or cause to occur: (a) distribution of this
or any Project Gutenberg work, (b) alteration, modification, or
additions or deletions to any Project Gutenberg work, and (c) any
Defect you cause.
Section 2. Information about the Mission of Project Gutenberg
Project Gutenberg is synonymous with the free distribution of
electronic works in formats readable by the widest variety of
computers including obsolete, old, middle-aged and new computers. It
exists because of the efforts of hundreds of volunteers and donations
from people in all walks of life.
Volunteers and financial support to provide volunteers with the
assistance they need are critical to reaching Project Gutenberg’s
goals and ensuring that the Project Gutenberg collection will
remain freely available for generations to come. In 2001, the Project
Gutenberg Literary Archive Foundation was created to provide a secure
and permanent future for Project Gutenberg and future
generations. To learn more about the Project Gutenberg Literary
Archive Foundation and how your efforts and donations can help, see
Sections 3 and 4 and the Foundation information page at www.gutenberg.org.
Section 3. Information about the Project Gutenberg Literary Archive Foundation
The Project Gutenberg Literary Archive Foundation is a non-profit
501(c)(3) educational corporation organized under the laws of the
state of Mississippi and granted tax exempt status by the Internal
Revenue Service. The Foundation’s EIN or federal tax identification
number is 64-6221541. Contributions to the Project Gutenberg Literary
Archive Foundation are tax deductible to the full extent permitted by
U.S. federal laws and your state’s laws.
The Foundation’s business office is located at 41 Watchung Plaza #516,
Montclair NJ 07042, USA, +1 (862) 621-9288. Email contact links and up
to date contact information can be found at the Foundation’s website
and official page at www.gutenberg.org/contact
Section 4. Information about Donations to the Project Gutenberg
Literary Archive Foundation
Project Gutenberg™ depends upon and cannot survive without widespread
public support and donations to carry out its mission of
increasing the number of public domain and licensed works that can be
freely distributed in machine-readable form accessible by the widest
array of equipment including outdated equipment. Many small donations
($1 to $5,000) are particularly important to maintaining tax exempt
status with the IRS.
The Foundation is committed to complying with the laws regulating
charities and charitable donations in all 50 states of the United
States. Compliance requirements are not uniform and it takes a
considerable effort, much paperwork and many fees to meet and keep up
with these requirements. We do not solicit donations in locations
where we have not received written confirmation of compliance. To SEND
DONATIONS or determine the status of compliance for any particular state
visit www.gutenberg.org/donate.
While we cannot and do not solicit contributions from states where we
have not met the solicitation requirements, we know of no prohibition
against accepting unsolicited donations from donors in such states who
approach us with offers to donate.
International donations are gratefully accepted, but we cannot make
any statements concerning tax treatment of donations received from
outside the United States. U.S. laws alone swamp our small staff.
Please check the Project Gutenberg web pages for current donation
methods and addresses. Donations are accepted in a number of other
ways including checks, online payments and credit card donations. To
donate, please visit: www.gutenberg.org/donate.
Section 5. General Information About Project Gutenberg electronic works
Professor Michael S. Hart was the originator of the Project
Gutenberg concept of a library of electronic works that could be
freely shared with anyone. For forty years, he produced and
distributed Project Gutenberg eBooks with only a loose network of
volunteer support.
Project Gutenberg eBooks are often created from several printed
editions, all of which are confirmed as not protected by copyright in
the U.S. unless a copyright notice is included. Thus, we do not
necessarily keep eBooks in compliance with any particular paper
edition.
Most people start at our website which has the main PG search
facility: www.gutenberg.org.
This website includes information about Project Gutenberg,
including how to make donations to the Project Gutenberg Literary
Archive Foundation, how to help produce our new eBooks, and how to
subscribe to our email newsletter to hear about new eBooks.Source: Project Gutenberg ebook #38387. Public-domain status is recorded per item; the licence text above is reproduced unchanged.