Gutenberg · e01.org
Cover of The Repairing & Restoration of Violins
Project Gutenberg cover, or a typographic cover where none is held.

Gutenberg · ebook 26878

The Repairing & Restoration of Violins

by Horace Petherick · English · public domain in the US

  • Language English
  • PG edition 2008
  • Rights public domain (US)
  • Source Project Gutenberg
0%

Contents

    The Repairing & Restoration of Violins by Horace Petherick is an English public-domain text held from Project Gutenberg (ebook #26878). 3, GREEN TERRACE, ROSEBERY AVENUE, LONDON, E.C.

    CHARLES SCRIBNERS' SONS, 153-157, FIFTH AVENUE

    1903.

    CONTENTS.

    PAGE

    CHAPTER I.--Introductory . . . . . . . . . . . . . . . . . . . 1

    CHAPTER II.--Slight Accidents--Modern Restorers--"Chattering"--
    The Proper Sort of Glue--Its Preparation and Use . . . . 3

    CHAPTER III.--Minor Repairs--Cramps and Joints--Violin Cases--
    Rattles and Jars--Loose Fingerboards--Atmospheric
    Temperature--Old-Fashioned Methods of Repairing--Modern
    Ways--A Loose Nut . . . . . . . . . . . . . . . . . . . . 13

    CHAPTER IV.--Injuries to the Head or Scroll--Insertion of Fresh
    Wood--Colouring of White Wood--Separation of Head from
    Peg-box and Re-joining--Stopping Material for Small Holes
    or Fractures--The Peg-box Cracked by Pressure . . . . . . 28

    CHAPTER V.--Fracture of Peg-box and Shell--Chips from this
    Part--Filling up of Same--Restoration to Original Form,
    after Parts have been Lost--Worn Peg-holes, Re-filling or
    Boring Same . . . . . . . . . . . . . . . . . . . . . . . 46

    CHAPTER VI.--Loosening of Junction of Graft with Peg-box, and
    Refixing Same--Grafting, Different Methods of Performing
    this--Lengthening the Neck--Old and Modern Method--Renewal
    of Same--Inclination of Neck and Fingerboard with Regard
    to the Bridge--Height of Latter, and Reason for It . . . 58

    CHAPTER VII.--Finishing the Fingerboard--Fixing the Nut--Size
    and Position of Grooves for the Strings--Filing Down the
    Graft--Smoothing, Colouring, and Varnishing Same . . . . 84

    CHAPTER VIII.--Injuries that can be Repaired from the Outside--
    Insertion of Fresh Wood in Fracture of the Ribs--The
    Effects of Climate on the Glue in Violins . . . . . . . . 92

    CHAPTER IX.--The Glue Used by the Early Italian Makers--
    Insertion of Pieces of Wood for Repairing Lost Parts--
    Replacing Lost Rib and Repairing Interior without Opening
    when Possible--Securing Loose Lower Rib to End Block--
    Different Methods--Treatment of Worm-holes--Fixing on
    Graft on Neck . . . . . . . . . . . . . . . . . . . . . . 100

    CHAPTER X.--Ways of Removing the Upper Table and the Neck--
    Cleansing the Interior--Preservation of the Original
    Label--Closing of Cracks in Upper Table . . . . . . . . . 114

    CHAPTER XI.--Getting Parts Together that apparently do not
    Fit--The use of Benzine or Turpentine--Treatment of
    Warped or Twisted Lower Tables . . . . . . . . . . . . . 127

    CHAPTER XII.--Removal of Old Superfluous Glue by Damping--
    Replacing Old End Blocks by New Ones--Temporary Beams
    and Joists Inside for Keeping Ribs, etc., in Position
    while Freshly Glued . . . . . . . . . . . . . . . . . . . 135

    CHAPTER XIII.--Re-opening the Back to Correct the Badly
    Repaired Joint--A Few Words on Studs--Filling Up Spaces
    left by Lost Splinters--Matching Wood for Large Cracks,
    etc. . . . . . . . . . . . . . . . . . . . . . . . . . . 145

    CHAPTER XIV.--Repairing Lost Portions--Margins of Sound Holes--
    Matching the Grain--Fixing and Finishing Off--Replacing
    with Fresh Wood Large Portions of Upper Table--Lost Parts
    of Purfling--Restoring It with Old Stuff . . . . . . . . 155

    CHAPTER XV.--Repairs to Purfling (continued)--Filling up an
    Opening Extending to the Whole Length of the Violin--
    Fitting the Core--Fixing it in Position and Retaining it
    There--Finishing the Surface . . . . . . . . . . . . . . 163

    CHAPTER XVI.--Repairing Undertaken by People in Business not
    connected with that of Bowed Instruments--Removal of a
    Fixed Sound Post--Fitting a Fresh Part of Worm-Eaten Rib--
    Bringing Together the Loosened Joint of the Back Without
    Opening the Violin . . . . . . . . . . . . . . . . . . . 172

    CHAPTER XVII.--Insertion of Studs along the Joint Inside
    without Opening the Violin--Lining or Veneering a Thin
    Back . . . . . . . . . . . . . . . . . . . . . . . . . . 180

    CHAPTER XVIII.--The Bar in Olden Times--The Modern One--The
    Operation of Fitting and Fixing the Bar--Closing and
    Completion of the Repairs--Varnishing of the Repaired
    Parts having Fresh Wood . . . . . . . . . . . . . . . . . 186

    PREFACE.

    An ancient writer once asserted that "of making many books there is no end"; had the violin been invented and used as far back as his day he might have added, "and of repairs to violins," inasmuch as the number, nature, and variety of the damages that constantly occur and find their way into the presence of the repairer, are such as could not be counted and seemingly are endless. The readers of the following pages will therefore not expect to find every possible ailment to which the violin is liable, mentioned and its appropriate remedy marked out.

    If the more minute kinds of injuries are endless, they may yet be generalised under a limited number of headings, or in groups. It is with the hope that a sufficient number has been treated of, and the way of meeting difficulties pointed out plainly enough to enable the intending practitioner to follow on in the same lines, that this work is placed before the public.

    All the repairings referred to, have, with the accompanying annoyances and pleasures, been gone through by myself, and therefore the present little work may be taken as the result of personal experience and it is hoped may be acceptable to the readers.

    H. PETHERICK. July, 1903.

    The Repairing and Restoration of Violins.

    CHAPTER I.

    INTRODUCTORY.

    The art of the old liutaro of Italy may be said to have become during the last two or three centuries, identified with the art of constructing such musical instruments as are played with the bow.

    As was the case with other and kindred arts, that of violin making had its rise in one of the old cities of Italy, where from small beginnings it gradually spread to other places and over the borders, until there are very few places of importance where it was not practised with some degree of success, commercially if not artistically and acoustically considered.

    During the early period of the art, repairing was of a rough and ready kind, chiefly in connection with damages sustained under ordinary usage and accident; while extensive and costly renovating, such as is so frequently undertaken at the present day, must have been of rare occurrence, for the reason that it was then quite possible to get equal, sometimes better, quality in quite new instruments which were being sent forth every day by the resident makers.

    With the onward march of time this has been changed; the art of the Italian liutaro having reached its climax some century and a half back, the masterpieces executed during that time are gradually diminishing in number and cannot be replaced by instruments having a sufficiently high degree of excellence; naturally enough the skill of the repairer has been more and more in requisition, so much so, that many who have shown exceptional ability for this kind of work have achieved a reputation for it alone, among the large circle of dealers in the principal cities of Europe.

    The necessities of the time have thus brought into prominence a modification of the art of the old Italian liutaro, in which there has to be displayed much more mechanical ingenuity if with very little or no originality; the high class of artisan has become strongly in evidence, while the artist has disappeared.

    It was in the consideration of these facts that the idea was first suggested that a work treating of the general methods adopted by professional restorers for important work, coupled with helpful hints in the management of minor injuries, would be interesting and acceptable to amateur as well as professional repairers, besides the numerous readers of THE STRAD, in the pages of which the following chapters were first issued.

    In sending out the matter in book form, some alterations and additions have been, as usual, found advisable for completeness. All readers readily admit the impossibility of touching upon one half of the various accidents and ailments to which a violin is liable during its usually long life; the most likely ones have therefore been taken, and it is hoped that the suggested treatment of these cases may enable the repairer to become sufficiently adept for undertaking such others, serious, or slight, as may not have been here referred to.

    Further, the author is hopeful that those readers who may feel indisposed themselves to put into practice the various hints, instruction, or advice, will be enabled by knowing how good repairing is carried out, to select the proper kind of person into whose hands they can safely intrust their cherished instruments.

    CHAPTER II.

    SLIGHT ACCIDENTS--MODERN RESTORERS--"CHATTERING"--THE PROPER SORT OF

    GLUE--ITS PREPARATION AND USE.

    Under the above title (dry and unpalatable as the subject may seem at first sight to many) it is proposed to bring before the reader some deductions from observations in general, and particulars in detail that may be interesting as to the past, and suggestive as to the future.

    In the first place, the simple art of repairing a violin--and as for that, anything that has been fractured by accident or intent--will be in the minds of many associated with the presence of some strong glue or adhesive material, the right pieces to be attached, neatly or not, as the skill or experience of the repairer may be sufficient or available.

    The nose or limb of a marble statue knocked off and lying in close proximity to the main body may be thought to give little or no trouble further than the collection of the fragments, the ascertaining of their original relationship, the spreading of a sufficient amount of strong cement over the raw surface and then pressing accurately into position; easy work to a person endowed with average powers of mechanical adaptation, under circumstances where the materials being of an unyielding nature retain their form for any length of time.

    But if any parts are lost different faculties and powers educated for the work are requisite and brought to bear on the subject. The additions, besides the estimated proportions and form, must necessarily be composed of material differing in age, perhaps in quality, even when of the same supposed class as the original, and make further demands on the trained eye, both for discrimination of material and appropriateness for the work in hand.

    There will be lastly, but not least, the art of imitating old work, the consideration how far to go and when to stop in the dressing up of new bodies in an old guise so as to produce harmony of effect generally, and where possible in minute detail. Thus far concerning the repair or restoration of objects of art made from rigid materials, including hard wood carving.

    Much ability, energy and patience have been expended on the reparation of ancient art work in which materials of various degrees of hardness and texture have been employed, and which require the attention of a restorer of extended knowledge and mechanical dexterity. There is in connection with all of this a kind of law keeping pace with the necessities of the hour.

    If the works of art of a perishable nature become recognised as more and more valuable during the onward march of time, they receive proportional attention from upper-class or highly skilled workmen. A costly work of art in need of repair or restoration is placed in the hands of an artificer whose reputation warrants the confidence of the owner.

    The works of art, however, with which our subject is connected, differ in important particulars from those for which gratification of the senses is to be favoured solely through the medium of the eye; they not only frequently demand the exercise of mechanical ingenuity of no mean order for purposes of restoration in regard to general appearance, but further and additionally, the no less important details concerned in a renewal, so far as may be possible, of their powers for the exhibition of acoustical properties such as were implanted in them by their original constructors.

    In the instance of a re-uniting of separated pieces, the insertion of fresh material to fill up spaces that must not be left open, strengthening, or even renewal of such parts as may have become worn away or--as is too often met with--"honey-combed" from the inroads of those vandals of all time known as "the worm," all the supporting, rebuilding of the interior and re-decoration of the exterior must be taken chiefly as means to an end, that of the resumption of its rightful position among friends or rivals in the same line.

    This restitution becomes of increasing importance and necessity every day, a condition arising from the verdict emphatically given by his majesty the public that there are not any instruments of the violin family ready to take the place--that is, worthily--of those made by the principal masters of Italy during the two hundred odd years before the commencement of the nineteenth century, and also that there does not seem to be much probability of others arising at least for a few generations to come.

    No wonder then that the most energetic searching has been going on for a long time, not only in Italy but over the whole of Europe, with the hope that in some out of the way court or alley there may yet be reposing in obscurity some long forgotten, unrecognised work by an old master of the art of violin making.

    Should one be unearthed, if but a wreck of its former greatness or even a portion, this is not refused but eagerly grasped and placed--not yet in open daylight before the gaze of the world, but in the hands of a specialist in re-vivifying these dry bones of a bygone age, re-habilitating them--perhaps having by him or given him other portions of a similar maker, or it may be--it has sometimes occurred--the actual missing parts.

    The specialist in the repairing and restoring art is now not of the same class as in olden times. When the Amatis, Stradivaris, Guarneris and the like were being turned out one after another, there was not so much necessity for preserving all the pieces or splinters of precious pine that had been separated by the fracture of the upper table from any cause, there was a better remedy at hand, the nearest maker would naturally be sought whose reputation was possibly more than local and whose self confidence prompted him to make a fresh table rather than devote time and labour for which adequate compensation could not be hoped for.

    As a result, we frequently find old violins and their kindred turning up with fronts and backs which, although fitting well as regards size and outline, have been made by a distinctly different workman, in some instances equal or even superior to the originator.

    At the present day, however, this kind of restoration is much more rarely attempted and is not resorted to unless the damage is very extensive or vital portions have been irrecoverably lost.

    The modern maker has no longer within reach, pine with requisite acoustical properties, of which the old Italian masters seem to have had so large a store, or if not, the knowledge where to obtain it. As a consequence there has, in response to the pressure of necessity, arisen a class of workmen some of whose dexterous conversion of a mere bundle of splinters of an old master into the semblance of its former grandeur of aspect would have astonished the original designers.

    These modern restorers are not to be confounded with the minute imitators or forgers, than whom they are much more clever, hard-working and honest withal. The art of repairing and restoring has now become so distinct from that of making, that many in the foremost ranks in the increasing large army of restorers may never have made a violin throughout.

    The faculties, skill and experience directed on the restoration of a violin "on the sick list," differs from those exercised by the first constructor whose mechanical dexterity is an aid or secondary to other qualifications: whereas it is paramount in importance in the constitution of a first class repairer.

    The construction of a violin from beginning to end may be said to be an art based on certain fixed principles, not all of them known, however.

    When these are, as far as possible, acted upon by a workman of sufficient intelligence and training, the progress of the work may be considered as being in a fairly straight and open course. Not so with the restoration of it after fracture or loss of parts great or small, several different courses may be open as to treatment and this will be as the temperament of the restorer will suggest or the exigencies of the moment may demand.

    Temporary alleviation of symptoms--how to make the thing go somehow--when there is no fiddle physician within beck or call, is a problem frequently arising and very annoying, necessity then being the mother of invention, often of a most curious sort, as most professional repairers who have had the re-consideration of the matter will have impressed on their memories.

    Among the most frequent of simple ailments the fiddle tribe is subject to, is that known as "chattering" or jarring, caused mostly by some parts having become dis-united, perhaps through damp or accident sometimes of a most trifling nature, and which henceforth, unless remedies are at once applied, make themselves evident in this way, accompanying every note that happens to be in unison with themselves, and lending discord instead of harmony, expressing urgently their thirst and desire for a small drink from the glue pot.

    Not unfrequently the exact spot where the jarring or chattering takes place is not easy to find by mere examination of the exterior, especially if the separation is fresh and at a part where very little adhesion has taken place at any time, or possibly the very slight portion of glue originally placed at the time of construction, has, with the progress of time, gradually dried away.

    Should this have occurred at the junction of the upper or lower tables (most frequently the first), the sides, or ribs, the exact spot must be found by gently tapping all round carefully, holding the instrument meanwhile firmly at parts that are least likely to have become disconnected or that are known to be perfectly sound. The tapping or sounding can be done in the way usual with dealers and repairers, that is, by the knuckle joints of the hand rapping round the instrument, but this is sometimes deceptive, the tendons over the bones of the hand interfering and occasionally causing a double sound, and so defeating the efforts at discovery.

    A more delicate and therefore better means of testing is by the use of a felted hammer of the kind and size acting on the bass string of a grand pianoforte; this will be found very handy.

    Should the rapping or sounding all round the border not reveal any weak spot, we may be sure the seat of the complaint is to be sought for elsewhere; possibly there is looseness in the interior and therefore something requiring deeper consideration.

    We will for the present assume that there has been no uncertainty in locating the weakness, and that it is at the part before referred to as the most frequent in showing signs of disorder--the upper table losing its grip on the ribs. This is one of the many common ailments that are teazing to the violin during its troublous career; a slight accidental tap, or hastily putting the instrument to rest in a too closely fitting case being often sufficient.

    Sometimes, on the reverse, it is from being in too large a one, getting well shaken while being taken home after some orchestral rehearsal; the joy of having mastered Mozart or battered Beethoven for an evening is turned in the morning to grief and vexation, when in response to the gentle persuasions of the bow there are but chatters and jarrings.

    Under such circumstances the treatment administered by the hands of non-practical or inexperienced people is akin, more often than not, to that popularly supposed to be effectual in suppressing slight functional disorders of the human system; namely, a prompt and appreciable dose of medicine for the one, a good stuffing of thick dark glue for the other.

    In both cases it may well be said that not unfrequently "the remedy is worse than the disease." Glue is a good thing in its way and when properly applied, but not so if overdone, even if the kind is the best obtainable.

    A few remarks may here be offered as to the qualities that should be present in good glue, especially with regard to violin repairing. Among the makers of it, the glue which will absorb the largest quantity of water ranks as the best. It will, after proper application, resist best the action of moisture in the atmosphere, or in fact take longer time before releasing the two surfaces it may have been holding in contact.

    There is not much difficulty in getting glue very satisfactory in most respects--as good animals die now-a-days as ever got into the gluepots of the old masters--but it must be selected. That kind used extensively in the German manufactories is said to be a fish glue, remarkably hard, very light in colour and almost opaque.

    This is not to be recommended for violin repairs; it holds the parts together with such tenacity that fresh fractures are likely to be caused in undoing a portion, a process often very necessary; professional repairers will tell you "it tears the wood too much." The glues mostly in favour among upper class repairers are those known as Russian, Cologne and Isinglass, all good; they are light in colour, very firm, not too brittle, and transparent.

    There are other varieties to be had of excellent quality and which conform to the conditions required. Thick cakes of a dark brown colour with an unpleasant odour should be avoided; they are too easily affected by the atmosphere, turn bad in the gluepot under very little provocation from damp warm winds, and spoil the look of good and refined workmanship.

    There are many different kinds of glue sold under various titles, some termed "liquid glue," others cement, apparently for saving the very insignificant time and trouble in warming up the orthodox solution; but none appear satisfactory in general and many of them are even detestable.

    There are some adhesive materials used in India where warmth and damp have their full play and make short work of an old master's joints, but these cements of the Eastern Hemisphere are likewise unsuitable for the kind of work under consideration, as when once dried, being unaffected by damp to any extreme, they are of course difficult to remove when further repairs have become necessary.

    One of the special advantages of glue to the repairer is its yielding to the direct application of moisture, so that in future repairings the old stuff can be washed completely out and fresh glue used over clean work. Let all amateur repairers therefore, abstain from seeking after a vain thing of the nature of glue impervious to moisture.

    One word more, as preachers say, and that is as to the preparation or melting of the glue--simplest of processes--some pieces of selected glue put into a small glazed gallipot with two-thirds of clean water and left to soak during the night will only require warming in the morning by placing the pot in a larger one and surrounding it with hot water. The quantity of glue being varied according to requirement is far preferable to the old-fashioned iron glue-pot which darkens the glue and is in other ways objectionable.

    If the injury or want of adhesion extends only to a trifling distance round the edge and has happened at a time when good glue and proper appliances are not to hand, the routine pursued must still be the same as if they were: first by obtaining a well-worn table knife, the thinner the better (but if the household knives happen to be new and strong you may call on some artist friend, borrow his palette knife, clean it, have ready some clear water, a cushion or a substitute, and some rather thick gum).

    If time will allow, the strings should be taken off the violin, and then placing it face downwards on the cushion, the knife having been dipped in the water, can be inserted gently at the part requiring attention. (Diagram 1.)

    [Illustration: DIAGRAM 1.]

    You will soon tell by the sound in moving the knife about whether the separation has been recent or of long standing, if the latter, the slipping of the knife will cause a slight grating sound and when drawn out will show signs of dirt. The knife must be rinsed and re-inserted a sufficient number of times until all the evidence of dirt has disappeared, the knife coming away clean and not gritty. Care should be taken meanwhile to keep the violin on the tilt so that the water introduced on the surface of the knife does not run inside but outward to the edge; the parts should also each time be wiped by a clean absorbent piece of cotton or linen.

    The knife can then be charged with gum instead of water and inserted as before, the process being finished by the wiping.

    But now the question will arise how about the closing up and pressing together of the parts. For this, assuming that the part to be rejoined is not of great extent, the chin-rest--almost every player now uses one--can be applied to the part and fixed in the usual way. If there is not one to be had, some pieces of ordinary deal, the softer the better--fire wood will do--cut into shape as depicted (Diagram 2) can be fitted, but very loosely to allow of thin wedges being used to tighten the grip (Diagram 3).

    They must be very gently pushed in, or the border of the violin will be damaged. Some paper placed between the wedge and the border will help in preserving the latter from injury or marks. The above suggestions are only intended to be applicable when the violinist may be out of reach of any professional or competent repairer. Gum arabic or dextrine are not comparable with good glue for repairs, although with care and attention to the details enumerated here I have known it answer when in pressing haste, and even for a permanency.

    [Illustration: DIAGRAM 2.]

    [Illustration: DIAGRAM 3.]

    CHAPTER III.

    MINOR REPAIRS--CRAMPS AND JOINTS--VIOLIN CASES--RATTLES AND

    JARS--LOOSE FINGERBOARDS--ATMOSPHERIC TEMPERATURE--OLD-FASHIONED

    METHODS OF REPAIRING--MODERN WAYS--A LOOSE NUT.

    The professional repairer is of course always provided with the well known wooden screw cramps as used in all countries for centuries, but if "up to date" men, they will have affixed the modern covering of cork or leather at the parts coming into contact with the instrument. No end of damage has been done at all times by neglect of this simple precaution. Many gems from the old masters that would otherwise have been matchless, are disfigured by an array of semi-circular dents or bruises near the border. This is particularly noticeable when the arching springs rather abruptly from a narrow channel and near the purfling, or the rise commences from the border without channelling.

    Here is shown the wisdom of the earlier Italian masters when introducing the channelled model, the hollowing being a preservation against damage by the impetuous repairer. Many otherwise excellent workers are heavy handed, pressing all parts together very tightly but not more securely. Good joints, cleanly and accurately cut, the surfaces kept clean and not overloaded with good glue, are the best for lasting, and of course for appearance.

    Before leaving that part of our subject which is connected with damages to the violin resulting from want of precaution or thoughtlessness, it may be as well to refer to a frequent cause of disaster, often well nigh ruin, by the use of badly fitting and badly constructed cases.

    Innumerable as have been the varieties of style, shape and arrangement of violin cases, there is still an opportunity for a new, good and useful one that shall combine all or most of the requirements as regards utility, portability, preservativeness and nice appearance.

    Those in use for travelling with during the last century and the early part of this, had the disadvantage of heaviness, besides their rounded forms which prevented their being placed with a flat side downwards on a shelf or convenient horizontal surface without some unsteady rolling; also being often studded with brass nails like a coffin, a very grave objection (diagram 4).

    The leather cases which require the instrument to be placed in sideways have the advantage of giving good protection against rain, but there is insufficient defence against accidental violence; they are, further, more expensive than the foreign boxes made of poplar wood, which are light and of sufficient strength when carefully made. There was one good thing about the ancient cases, however, the violin being inserted at the large end, the performer knew at once whether the case was sufficiently capacious for the instrument.

    Not so with those in common use at the present time, opening as a box.

    To these may be laid the charge of causing an immense amount of irreparable injury to numbers of violins of any standard of excellence or costliness. This in the way mostly of depressions--"wells" as they are termed by repairers--where the feet of the bridge rest. These are caused by the lid of the case coming down on to the hard wood of the bridge and pressing its feet like dies, into the comparatively softer pine (diagram 5).

    It is a disfigurement to the violin and is sometimes in a bungling manner altered by inlaying--badly in most instances--square pieces of wood to bring the surface level. This kind of damage to the violin has been attributed to the prolonged pressure on the upper table by the strings being stretched up to modern pitch, but this is a mistake, no strings at all playable would press sufficiently hard and directly downwards to produce this result. The double-cases in use are worse than the single, as they are necessarily stronger and heavier.

    Both present the same difficulties in estimating whether the violin with its bridge is too high for the roof inside when the lid is closed. A good way of testing it is by rubbing a little soft white chalk over the top of the bridge and then gently shutting the lid down, which also should show no indisposition to do so; if on lifting the lid any of the white chalk is seen to have changed places and got on to the lining of the lid, put aside at once and for ever the condemned case as being an unfit receptacle for your cherished Cremona.

    Further, if the fit is at all tight, do not use pressure but get another case, your violin would be a very bad one indeed for your sympathies to fall in with a horrible suggestion once made by the maker of a too closely fitting case for his friend's instrument, that he should be allowed to take a shaving or two off the violin, it would then go in nicely. As some excuse for this maker he was not an amateur in this line, but a professional undertaker.

    [Illustration: DIAGRAM 4.]

    [Illustration: DIAGRAM 5.]

    We may now shift our ground and notice another source of the complaint--rattles, jars, chatters, or grunts, which ever may appear the most appropriate title for another variety of annoyance to the performer. Having found out with our felt-headed hammer, or if that is not easily obtainable, a slender stick may be covered at the end with almost any soft material enclosed within a piece of chamois or soft leather, and tied so as to form a knob like a small drumstick.

    Having tested the violin with it in the manner before referred to, and there being no bad reports from the body of the instrument, the hurt, seat of injury, or lesion, may be in the neck, fingerboard, or even the scroll, any part being liable to give out its undesirable note, or interfere with the proper emission of musical tone from the strings.

    There is no portion of the violin that will not under certain provocations join too willingly in the production of unwelcome sounds if the exciting conditions are present--those of checked vibration, or vibration that should be checked. An unsuspected cause may be discovered by the tapping test to be lurking unseen, and often unfelt, till one note being struck in unison or sympathy with the affected spot, may cause it to speak in a decided manner.

    This is at the part where the fingerboard parts from the neck over the instrument towards the bridge--the rather thin glue, as it should be--may, through damp or other causes, have lost its hold for but a short distance, and not be evident while the fingers are pressing the strings over the part; but when notes are struck nearer towards the nut, the pressure is relieved and the fingerboard free to take its own part. This, although a trifle in itself, requires for its cure proper attention with suitable appliances.

    After the removal of the strings, the first suggestion naturally occurring will be to insert, with the blade of a knife, some glue and leave it to dry. This is more likely than not to make matters worse, as it should always be borne in mind that glued surfaces always require pressing together, however well they may fit. Glue contracts as it dries, and in the process apparently disperses and clings to any other bodies rather than to itself.

    To put this in another way, if air is allowed to insinuate itself between the two surfaces which it is desirable to bring into closest conjunction, the contraction, particularly if good, while in progress, will cause a separation in the central mass of the glue, while the two surfaces will be left as before, independent of each other, but more clogged.

    Pressure must therefore be invariably brought to bear behind the opposing parts, so as to drive out the air from between and prevent its re-admission--the necessity of an exact correspondence of the parts will be obvious--at the same time the glue is to some degree forced into the pores of the surfaces, and when the moisture has dispersed among the myriads of cells composing the structural growth of the wood and finally evaporates from the external ones, the glue, having hardened, will hold the parts together with a tenacity that can only be overcome by prolonged application of moisture or actual destruction of the parts.

    There is one very important consideration in connexion with glueing operations that must not at any time be lost sight of--that of atmospheric temperature. Much trouble may be brought about by inattention to this help or obstruction, for it will act both ways according to circumstances.

    In the glueing of important parts in the construction of pianofortes, the operators are careful to have the temperature of the surrounding atmosphere sufficiently elevated, as well as heating those portions of the structure which are to be accurately and lastingly joined, and particularly where hard woods and smooth surfaces are brought together. The violin repairer must strictly follow the same rule. The degree Fahrenheit at which glueing operations are best conducted may be roughly estimated as nearly seventy.

    The reason for this is that the nature of good glue is to coagulate or "set" rapidly in a cool atmosphere and in this state--not perceptible at once to the eye--it will resist a considerable amount of pressure, the surfaces that should exactly cohere, slipping aside and the whole work having to be done over again, perhaps with fresh damage.

    To return now to our loose fingerboard, an old fashioned and very clumsy, inefficient way of fastening it after glueing, was to tie some string round it, which of course getting much glue upon it during progress had, when dry, to be torn or washed off. The modern, simplest and best way is to have ready a soft wood mould with a square or flat back for the under or circular part of the neck, and a similar but flatter one to fit above on the fingerboard.

    These can be easily adjusted, and the requisite pressure obtained by several screw cramps along its extent (diagrams 6 and 7). It is not very often that the nut or small block over which the strings pass on to the pegs gets loose, if it does, it is the result of bad fitting and careless glueing.

    If it should happen to come away, wash it, and when dry see that the under part to be stuck to the fingerboard and the neck is quite square and level; warm it and apply some strong glue to the two surfaces, and also to the parts with which it is to come into contact, you can then place it in position; press down and rub backwards and forwards once or twice, then leave in the exact position required; if clean, accurately fitted and warmed, it will not require any further pressing or clamping.

    If this part should have been knocked off and lost, then a new one must be made.

    For this purpose the hardest piece of ebony you can obtain is the best; sometimes a nut of ivory or bone is used, but it has a staring effect, although if properly done as above described, it holds well and wears slowly. Some of the hard dark woods, cocoa wood and lignum vitae, or dark horn are adapted for this purpose. Rosewood is not so well suited, as the ruts or grooves are soon made deep by the friction of the strings in being wound up, and renewal is found obligatory sooner than with the other.

    [Illustration: DIAGRAM 6.]

    [Illustration: DIAGRAM 7.]

    Having selected a suitable piece of wood it must be cut or planed square and equal in thickness. It should be as nearly the right length as possible before being placed permanently in position, the ends being very tough in cutting.

    If by miscalculation they are found to project over the width of the fingerboard, they should be--when the glue is quite dry--cut through with a small bow saw close up, a gentle, careful filing will reduce them down level with the side of the fingerboard; the surface should run easily with that of the peg box, which is not always of the same width as the other, the arching can then be proceeded with, a chisel being first used, then a rather close grained file for further levelling and the finishing off with the finest glass-paper or emery cloth, having a drop or two of oil in it; this will give a smooth, dull polish agreeable to the eye.

    The grooves in which the strings will have to rest must be marked out or pricked to measurement so that the spaces may appear regular when the violin is strung up.

    The distance apart being occasionally done to the caprice of the player, measurement should be kept of this matter of detail from some well regulated instrument as a standard to go by.

    When the exact spots for the grooves are marked or pricked, a very small, round or "rat-tailed" file may be used to work the wood down at the spot, care being taken that the file is constantly held in an exact line with the direction of the fingerboard, otherwise when strung up the appearance at the part will be that of distortion and the string will even be checked in its freedom in passing through the grooves, each of which should be made to receive the string not too tightly nor too loose.

    Of course the width of each groove must be in agreement with the thickness of the string, the widest being the D, the G a little less, the A less still and the E least of all; the E should be a trifle closer to the fingerboard than the D or G, the last, having the widest swing during play, should be raised further off the board than the others. The arching of that side of the nut may also be left a little higher.

    The nut should also be made to slant down towards the peg box (diagram 8), the grooves being of a regular depth on this and not deeper at the top (diagram 9).

    When all is ready for the stringing up, a soft lead pencil may be used for blackleading the grooves, they are otherwise liable to arrest the progress of the string towards the pegs when tuning up and suddenly letting them go with a click, making the tuning uncertain and difficult; if the wood is rather obstinate--it is not always alike--a touch of beeswax of the size of a pin's head where the lead is placed will be an effectual cure.

    [Illustration: DIAGRAM 8.]

    [Illustration: DIAGRAM 9.]

    We may now leave this as finished, going to the other end of the violin where another nut is used for supporting the tail-string as it comes over to the end peg. This part is frequently done in a slovenly way, even by some repairers of good repute; there is no reason why it should not be as neatly done in all respects as any other part. It may be that the supposition is uppermost in the mind of the repairer that, like the nut at the fingerboard, the pressure of the strings will retain it in position.

    This is a mistake, there is a great pull forward, especially if the wood is hard and dry. The material should be selected for its solidity and hardness like that for the other nut. In olden times, say those of the early Italians, this part, owing to the small amount of strain in consequence of low pitch, low bridge and short neck, seems to have been treated with almost indifference, a very slight piece of ebony, cherry, pear, or other variety of hard wood found in Italy, sufficing for the purpose (diagram 10).

    It was left level with the surrounding soft wood, or nearly so; there was no occasion for raising it at the time, as the tail-string projected from the underneath of the tailpiece instead of that almost universally now known as the secret tie (diagrams 11 and 12). This latter necessitates the use of a higher and more substantial nut, otherwise the tailpiece would be close down to, if not touching, the table, causing a rattling.

    Further, in accordance with mechanical law, the strain or pull forward increases with the height of the nut. It is therefore obvious, that unless well fitted and held strongly, the nut will be liable to be wrenched forward out of position. This is more frequent than would be suspected, and is sometimes a secret source of damage or bad influence leading to disaster in other parts of the instrument. The same observations concerning the preliminaries apply to the fixing of this as to the other nut. The modern arrangement of the part leaves but little to be improved upon.

    [Illustration: DIAGRAM 10. OLDEST FORM OF NUT.]

    [Illustration: DIAGRAM 11.]

    [Illustration: DIAGRAM 12.]

    The length and thickness of the nut required having been determined upon, we will suppose ourselves in the presence of an old worthy from Cremona requiring a fresh attachment, the wood selected--Mauritius ebony for preference--and the measurement as follows, 5/16 in length and thickness according to the width of the border, as the nut looks best when the inner edge runs in a continuous line with that of the purfling (diagram 13).

    In highly finished work and when the end of the violin has a perceptible curve instead of being nearly straight, the nut should be made to follow the course of the purfling, this will require some care in the cutting and finishing of it. For this a piece of almost any veneer cut to the exact flow or drawing of the line may be used as a guide or template. The block from which the nut is to be made having been cut quite level, the line can be traced with a fine pointed pencil, or better, a fine pointed knife, and then shaped with a sharp chisel.

    The block or nut can now be laid on the border, care being taken that the tail pin comes immediately in a central position in relation to it, and then with the sharp pointed knife a finely cut line can be traced all round. The space now marked may be cleared away down to the top of the end block with a clean, vertical wall on three sides formed by the pine. If carefully done, the nut, at present only a solid, squared block, will fit exactly, if too tight, a little shaving off here and there of the pine will correct it.

    The nut, supposed to be an exact fit, may be warmed and some fairly strong glue applied (diagram 14). The raw surfaces of the pine and the exposed end block are of course very absorbent and require an extra feed or two in order that the final glueing of the nut and place of reception may have a good holding. The nut, now squeezed into position, will not require the clamp, but if time is no desideratum an application of that useful tightener will ensure a firm hold, and moreover the superfluous glue is forced out.

    [Illustration: DIAGRAM 13.]

    [Illustration: DIAGRAM 14.]

    When the glue has had time to thoroughly dry and harden, the clamp may be released, and a part at each end of the nut marked off for levelling down to the surrounding forces by filing and glass-papering. The manner and care with which this is done declares the excellence and characteristics of the workman or firm by whom he is employed; almost every repairer or house of reputation having their individualisms in this respect, as also in that of the fingerboard nut (diagram 15).

    A line having been ruled with precision along the upper central part with the pencil or knife as before, a small gouge can be run along a hollow which will face the bridge. To give this the best kind of finish a piece of pine or soft poplar, such as is used for champagne wine cases, you may look out for one about Christmas time, cut it to the shape of the part to be finished thus (diagram 16), and with a piece of fine glasspaper, slightly oiled, a few rubs backwards and forwards will be necessary.

    The top of the back part can now be shaved gently down by a small metal plane, a little filing will give the evenness and rotundity required. The same treatment will be necessary for the under part, which in good work is a continuation of the line of the edging of the upper table. A section of the nut in its finished state will be as in diagram 17.

    [Illustration: DIAGRAM 15.]

    [Illustration: DIAGRAM 16.]

    [Illustration: DIAGRAM 17.]

    The whole of the surfaces may now be finished with the finest emery cloth and oil. This latter may be linseed, nut, poppy or castor oil with turpentine, but do not use sweet or olive oil, it never dries, but lurks about in the pores of the wood and turns rancid.

    Before leaving this part of the instrument, it may be as well to take a glance at the peg itself and its insertion at the centre underneath the nut. This is in no respect an unimportant detail to be seen to in the fitting up and regulation of a violin. In olden times the peg was small, not half the size of those inserted in new violins of the present day.

    The increase in the size seems to have been gradual and to compensate for the hard wood of the peg pressing against the inner, softer substance of the end block with the thin slice of maple used for the ribs, both being insufficient to withstand the strain of the tail-string. Consequently the peg is pulled upwards, sometimes considerably out of position. This is especially likely to occur if the hole has been bored too large or the peg is too thin or short. The accurate fitting of these should have strict attention.

    Some modern repairers, when they find that there are indications of a softer piece of pine than usual having been used, enlarge the hole with a tool specially made for the purpose, having two cutting edges, or with a number of grooves having sharp ridges, others a rat-tailed file. The latter is perhaps the best, as being less likely to split the fibres of the soft pine.

    The tool is inserted, not directly in a line pointing exactly midway between the upper and lower tables, but slightly upwards or contrary to the tendency of the peg to accommodate itself to the strain. When the parts under strain have settled down, the peg is seen to be as near as possible horizontal with the length of the violin.

    The best way, undoubtedly, is to make the peg an accurate but not too tight fit, it should be sufficiently long to go right through the block.

    In cases where the hole has been enlarged, badly directed or even made ragged by a bad tool, it should be a stopped up very carefully with a plug, neatly glued in, and a fresh hole bored. Sometimes this has proved necessary from the carelessness of the original maker. The old masters were not always exact with their mechanical fittings in connection with the violin. The moderns, for obvious reasons, have paid much attention to them. I remember coming across an Italian violin that had changed hands frequently for the asserted reason of insufficient tone.

    The maker having a renown for considerable power, it appeared to me that the tone was possibly there, but that from some undiscovered cause it was not properly emitted. On examination I found that the maker had joined the ribs, not at the central part as usual, but too much to the left, perhaps a pupil or assistant had bored the hole at the junction. There were besides, some tinkerings by modern regulators endeavouring to counteract the uneven strain over the instrument.

    The right spot, or it may be called the axis of the instrument, having been found, the peghole was neatly and permanently plugged, and a fresh one bored, which allowed the strain to be better distributed. The result was satisfactory and delightful; the tone of much power and purity had free play in manifesting itself, and the violin was enabled to take its rightful position among its brethren. A few words as to the right spot for the peghole.

    This was treated by many of the old Italian liutaros as a matter for mere guess work apparently, when there was no join in the upper table, nor in the lower one, sometimes the lower rib being continuous.

    The best spot, and therefore the right one, may be fixed upon by finding the centre between the two inner edges of the purfling on the upper table at the lower part, the same between that of the upper, and drawing a faint line through the points with a piece of soft white chalk cut to a point, and guided by a flexible rule or straight edge down to the nut. If this line does not touch at the centre of the nut, then the latter is out of place, and it should be rectified.

    The line should pass through the centre of the nut, and immediately underneath this and midway between the edges of the upper and lower table will be the spot for the centre of the peghole. The line thus made will not always be found to agree with the centre joint of the pine; many of the old Italian makers may have not, from lack of wood of the right sort and in equal widths, been able to do otherwise. At times it may have been carelessness.

    Some of their roughly made violins have the joint line over a quarter of an inch from the centre, occasionally it will be not only wider on one side than the other, but the thread or grain will diverge instead of running parallel with the centre line. The judiciousness of careful measurement for the centre, instead of relying on the joint line, will therefore be obvious. There is not much to be said in preference of one kind of hard wood over another for the end peg, it being a matter of fancy as to appearance.

    Ebony being black and very hard, should perhaps take the preference in wear, and acquiring a polish from the gentle friction it is liable to. The old Italian end pegs were mostly of cherrywood, with lines neatly turned round a centre of ivory or bone.

    CHAPTER IV.

    INJURIES TO THE HEAD OR SCROLL--INSERTION OF FRESH WOOD--COLOURING OF

    WHITE WOOD--SEPARATION OF HEAD FROM PEG-BOX AND RE-JOINING--STOPPING

    MATERIAL FOR SMALL HOLES OR FRACTURES--THE PEG-BOX CRACKED BY PEG

    PRESSURE.

    Leaving this part now, we can turn our attention for a time to reparation of injury to the head or scroll. This interesting and often highly artistic part of the general structure of the violin, and in which no man since the time of the old Brescian, Gasparo da Salo, has succeeded in effecting any permanent change of fashion, is subject to as many knocks as any other part.

    A piece out of the ear or first turn from the axis is, with a delicately carved scroll, so frequently seen as to be almost fashionable; little pieces out of the edges further off from the central part, are common disfigurements. Modern vandals rub these parts down with a file or glasspaper, to make it nice and even to their vision, saving themselves time and trouble. Many a graceful scroll, carved with loving care and enviable dexterity by a master of his art, has thus come to an untimely end.

    Should your cherished Guarneri or Stradivari scroll got chipped or fractured by accident and the piece drop, search for it at once, and when found, if you have not good mechanical ability and experience in fitting such delicate parts, it should, while fresh and free from soiling, be entrusted without delay to the care of a professional repairer of repute, but not to a provincial amateur or rough carpenter who would probably make matters worse.

    On setting to work after a preliminary inspection, the careful repairer will fit the parts together as they are, to ascertain that there is nothing to prevent a close join of the surfaces, sometimes a splinter will prevent a close fit of the surfaces; this must be pushed into its right position or, if in the interior, it may be better to remove it altogether.

    If the part is lost, then the bare space must be carefully examined and the direction of the grain and quality of the surrounding wood matched as closely as possible; otherwise the most accurate fitting and finishing off will not make a good restoration. The repairer of experience will have at hand a large quantity of odds and ends of different kinds of maple, curled or plain; perhaps old worn out necks or otherwise useless fragments of relics of a bygone age, and not necessarily of musical instruments.

    But sometimes these are not to be obtained, nothing but new or modern wood, and it may be of good appearance and applicable excepting for the colour. What is to be done? There is the drawback to new white wood, that it is difficult to colour down to match the surrounding wood, when it has been fixed, and besides, if the part happens to be where there is any friction, the white wood soon makes itself apparent, if not very conspicuous. It is advantageous, therefore, to colour the wood artificially before placing in position.

    There have been many ways adopted at times for meeting this requirement.

    It must be remembered, however, that there is no perfectly successful mode of artificially colouring wood so as to defy detection, but small portions such as are under consideration at the present moment may be treated so as to look tolerably well. Firstly, a well known, often tried, but very bad method is to steep a piece of white new wood in a solution of nitric acid and water. When dry, old age will seem to have crept over and through it, but of a delusive and unnatural kind.

    The corrosive properties of the acid still remain and gradually disintegrate the fibres until the whole mass becomes rotten. It may be fairly termed premature old age, as the lowering or toning down of the colour in wood and other materials seems to be caused by similar, if not identical, constituents of the ordinary atmosphere, but under different conditions. Another way is lay the pieces of wood upon a stove with a regulated heating power and watching for the exact degree of change in the colour with continued heat.

    There is very little to be said against it for small repairs, the degree of heat required for the desired tint is insufficient to damage the wood but enough to harden it, and if not too hastily done the colouring will go quite through.

    Among other methods is tinting the wood by any of the various stains sold for the purpose. Few of them are of any good to the violin repairer, some choking the softer parts and leaving the harder ones or threads standing out lighter when they should be darker. Their colour, if it were not for this drawback, is sometimes good. Some of the manufacturers of new musical instruments on the continent lower the colour of the wood before varnishing by staining it with a solution of bichromate of potash.

    Sometimes when dexterously applied the colour is very good, but the stain is liable to make itself too evident in parts where the wood may be a little more spongy than at others. Most of the instruments treated in this way may be recognised at a glance, the curl of the maple is brought out strongly, in fact overdone. With small portions of wood for repairing this stain may, with much caution, be used to advantage.

    It has the property of throwing up the threads of the pine and the nutmeggy parts of the maple without impairing seriously the clearness of the grain under the varnish. The preparation of the solution is as follows--some pieces of bichromate of potash can be put into any ordinary bottle of a convenient size and water poured on to them.

    The water will take up a certain quantity in solution which will be too strong for the repairer's use; some of it, say a gill, can be put into an equal quantity of clear water, and then painted over the wood to be coloured down.

    There will not be any perceptible colouring for half-an-hour or so, but further exposure to good or strong sunlight will gradually bring about a change from the slight orange tint to the dull light brown approaching that produced by the slow secret process adopted by "Old Father Time." It must be kept in mind that bichromate of potash is a poison. There are other stains that will bring a good colour to the surface of the wood, but are likely to change colour when the varnish is applied. The whole work of careful restoration may thus be upset in a moment.

    All stains should be carefully and repeatedly tested before being applied to any work of importance. Some repairers use a hastily made solution of powdered colour such as burnt umber, and paint or rub it into the wood. This process is to be condemned as resulting in opaqueness and giving a tinkered aspect to the wood and work.

    There are doubtless many substances or liquids capable of imparting a tint resembling that alone caused by age, but experience only will enable the repairer to decide which is best. It may be as well to point out that some tinting substances are more suitable for colouring wood of a dense quality than for a more open grained or spongy one. Much will depend on the judgment exercised and skill in matching tints.

    When it becomes absolutely necessary to use fresh white wood, this will require more colouring than an older piece, but a rather strange thing in connection with this is that if some of the varnish has been removed from the parts adjacent to the freshly inserted wood, the old material will require colouring down as well as the new, but not so much. This seems like some indication that varnish does get lowered in tint as age progresses; it may be, however, that the top surface of the wood gets darker than the under parts from the action of light.

    The final touching up or finish of the newly inserted wood and its varnishing will have to remain over for the present, and will be taken up after the mechanical work is concluded.

    Having thus far got to work upon a fractured or lost piece that may have been knocked off a projecting part of the scroll, there are other injuries likely to occur to this part of the instrument and caused in a variety of ways, some occasionally seeming mysterious in their origin.

    Thus from a weakness or flaw in the grain of the wood, or it may be from a blow having first started a crack and successive ones gradually increasing the fracture, the scroll itself will come away bodily, separating at the weakest part just behind the second turn. This is a delicate matter for manipulation.

    If the fracture is quite new, the raw surfaces uninjured and some properly prepared rather strong glue is handy, then an almost instant application of it to both surfaces and pressing them together, exactly fitting, will result in an effectual and lasting junction of the parts. But supposing the breakage to have occurred some time back and the parts to be separate and soiled, the difficulties are much increased, as in the majority of cases no purchase can be obtained whereby a good pressure can be directly applied.

    Cramps cannot be applied, therefore, with any degree of safety, even if a good grip can be obtained and with the safeguard of some padding, as the first is bound to injure the wood around, leaving an ugly imprint of the grip, and thus making things worse in appearance instead of better. The other is likely to be productive of slipping out of position, the hold not being retained, and vexatious results ensuing with the accompaniment occasionally of unprintable language coming from the repairer.

    The best way on all occasions will be found to be that in which patience is not taken as a virtue but as necessity, and the presence of Old Father Time altogether ignored, which may often mean time saved. Constant practice may give facility in keeping pace with that steady old party with the hourglass, but a good result is seldom obtained when the clock is much consulted during the progress of the work in hand. It is this which has caused the complete ruin of many a damaged gem from Cremona's workshops of the olden time.

    We will therefore suppose the repairer to be unfettered by time and that he will be properly paid for work that will tend to restore the commercial value, as well as the usefulness and beauty.

    The main consideration will be the manner of getting a proper attachment of parts that cannot be wedged or forced together at once, in fact, to get a good purchase or leverage. This must be either obtained indirectly or dispensed with altogether. For the former, building up or "making," as it is termed, must be resorted to, and which may include temporarily glueing fresh wood on to the old parts to be separated or cut away afterwards.

    Many inexperienced repairers are too apt to look upon all glueing as for permanency, but practice should soon make it plain that all joinings are effected only for such length of time as may be desirable. In making or building up a part from which we can obtain a stand or commanding point from which to get a more direct purchase, it may be necessary to glue one or more pieces of wood, cut to a proper shape and stuck with a dab of thick glue and left until dry.

    For this purpose the soft white wood or poplar referred to at the beginning will be found useful, it is so easily cut with a chisel or knife keen edged--this condition is an essential at all times. By the bye, some readers may be thinking of the best means of getting a nice clean edge to their knife or chisel.

    There are several kinds of oilstone or hone in repute for giving a finishing or sharp cutting edge, England, America and the European continent supplying them, the "Chalney Forest" being the commonest known in England; the American "Arkansas" or "Washita" are expensive when very good, but there is nothing that can beat a well selected piece of "Turkey stone" with a nice even surface to begin with. For obtaining a clean cutting edge, a few drops of oil before rubbing will be sufficient.

    Olive or good mineral oil will do, the latter preferably as it gradually evaporates; whereas vegetable oils acquire a siccative property from contact with the minute particles of steel; the stone then gets clogged and unworkable till thoroughly cleansed. Mineral oil disappearing gradually leaves but little residue, which can be now and again wiped off.

    In cases where the utmost delicacy of surface cutting or close fitting is required, and where no other tool but the chisel can be used, it may be as well to have at hand a stout, smooth leather strap fixed at each end over a piece of wood about twelve inches in length. The residue on the Turkey stone can be taken off with a knife--care being taken that no dust or grit is with it--and smeared on the strap with a little olive oil. The chisel or knife used briskly and gently on this will after a few passes become as near perfection of keenness as possible.

    After getting everything in readiness, which will include the carving to shape, of any wood that is to act as a support or fulcrum, these parts must be made to fit as accurately as possible, and may not require glueing but at one or two places and those selected to come in contact with those of the original structure least liable to be affected or damaged. Thus the interior of the peg-box will be found a convenient position from which to build a support that shall reach up underneath the volute or under turn of the scroll.

    Having well tried the parts as to the fitting, the support or prop may be secured or glued in roughly to the lower surface of the peg-box--presuming of course that the pegs have all been removed--and left to dry hard.

    When so the parts had better be tried for fitting again, and if any little inaccuracy shows itself, or the pressure in glueing the fracture is likely to be uneven and the junction be untrue, a little paper or card may be inserted or even glued in between, or where judgment may dictate, to enable a good distribution of the balance of pressure necessary.

    There can be no certain description given of the size or form of the supports or made up parts to be temporarily fixed; all must depend upon the estimation of what is best to be done under the circumstances; it can be likened to engineering on a minute scale, quite as interesting, but less dangerous, while more comfortably conducted in your own home without exposure to the baleful influence of unsympathetic elements.

    The next and most necessary proceeding will be the cleansing of the surfaces that are to be permanently joined. In most instances the application of clean cold water in a sponge will be sufficient, but where much grime and grease have accumulated different means must be resorted to. Soap is not to be recommended but, and especially if the surfaces are irregular, some pure benzine, applied or slightly scrubbed in by a stiff brush, not too large, and the parts then wiped repeatedly on a clean cotton or other absorbent rag.

    Pure benzine, if not rubbed in too hard or too long, will not injure the adjacent varnish, be it the delicate film on a thousand pound gem of Cremona or the flinty covering of a less presumptuous output from Naples. When evaporation is complete, it will be so in a few minutes, some clean water brushed in and wiped away, will leave the surfaces in a state for receiving glue.

    The glue should be of good strength--the junction being intended to be permanent--and applied in a warm atmosphere or the parts warmed a little, as, under different conditions the glue will coagulate or "set" (diagram 18). When the parts are placed properly in position, and the outside blocks or buffers adjusted for opposing pressure, the cramps may be applied and screwed fairly tight. If the surfaces meet well and the pressure is properly distributed, the glue will ooze out at the juncture of the fractured parts.

    This can be wiped off with a cloth, but occasionally mended parts cannot be got at easily, if so the glue must be rubbed away after cramps and moulds have been removed, by a damp sponge or cloth and then wiped dry. Sometimes differently to the above mentioned simple fracture, it may be of the kind described by surgeons as comminuted or split into small fragments.

    This will be found to be much more troublesome than the former; after cleansing as usual, if the injured parts are actually separated from the main structure, judgment must be exercised in selecting those portions--the largest if possible--that when glued in, will act as a support for others to be afterwards inserted. The same attention in kind and amount will mostly bring about a satisfactory result, but frequently with this class of fracture minute pieces may have been lost past recovery, leaving a small gap here and there to be filled up somehow.

    These places, if large enough, should have pieces let in according to the manner before described. If they are too small for this treatment--a little experience will enable the eye to judge at a glance--then the only course will be to fill them up with some kind of paste or improvised mixture. For this purpose a good "stopping" must be made. This has, in olden times as well as the present, been a difficulty to meet.

    Many kinds of material have been used, most of them having some objectionable quality; some repairers keeping some kind, others generally making further experiments.

    Among the various materials plaster of Paris or common chalk worked up in glue has been frequently used; it is certainly strong for some time after use, but gradually, as age creeps on, contraction takes place towards the central portion, and a small fissure all round is seen more and more evident, and which gets filled with grime causing a very distinct black line, which draws attention to the spot, the substance also being so much harder than the surrounding wood, gets polished with a little friction and usage and declares its unsympathetic nature; further, it is difficult to colour successfully, or even well, and for these objections it should never be used.

    Wax is another material that has been extensively in use among the older English repairers, but it has very little to recommend it except handiness, and that quality ought not to be placed in the balance against much more important ones. It is not easily colourable; with usage the top surface gets wiped off, leaving a hollow.

    Powdered wood with shellac, or the latter with some heterogeneous materials have also failed, as the alcoholic solution destroys the surrounding varnish.

    [Illustration: DIAGRAM 18.]

    Sealing wax has also in turn been used with no better result. Other substances are met with whose precise nature is not known, odd mixtures made up in a hurry at the moment of requirement, but no material or mixture has been found to excel that made with wood and glue. Many, perhaps the majority of instances in which this has been used, have also been failures; not from any inherent defect in the substance, but from lack of proper management. Different varieties of wood have been tried, a great drawback being the contraction when the glue dries; this is markedly the case when a hard wood, powdered by glass-paper, is used.

    The granulations and their hardness are also objectionable, and if ground up too small, contraction to a greater degree takes place, and the repairer's object is defeated. Long experience has shown that the disintegrated fibres of soft pine, not powdered, offer the best security against contraction, it can be made strong or weak according to the thickness of glue used, is always at hand, and on the whole gives the least trouble.

    It requires little or no colouring, and moreover approaches nearest in character--or can be made to do so--to the surrounding material. If there is a selection possible, the well known soft grained American pine should in preference be used. There is a good and a bad way of managing the process to ensue. To roughly seize a chump of wood and begin filing it away anyhow, collecting the residue and making a rough paste, will bring disappointment, as sure as houses built with wrongly mixed mortar.

    To put method into the matter, a piece of clear, knotless, soft, grained wood should be obtained and cut to a cylindrical form (diagram 19). A flat file of rather fine texture--this may be according to the size of the instrument to be repaired--should be worked against it at right angles. The file (not glass or sand-paper) must not be of the toothed kind, but grooved.

    The shower of particles sent off during the action of filing, will consist of a number of minute silky fibres, which, of course, must be collected together, placed upon a clean porcelain dish, or palette, and worked up with glue--strong--for filling spaces in the maple, and weaker, if used for the pine of the front table. It can be tucked into the crevices as required by the end of a small, worn, or pointed knife.

    Some portions will remain above the surface and, in fact, will not go in completely, owing to the fibrous, or threadiness of the mass, but this constitution is the safeguard against its contraction, the glue in drying clinging round the fibres instead of to itself. When dry and hard the projecting portions can be neatly levelled off. If, as will sometimes happen, a little hole or two can be perceived, perhaps under magnifying power, the process can be repeated on a minute scale.

    By attention to the above there will be but small risk of contraction, and if cleanly done there will not be much trouble in colouring the part to match the surroundings.

    [Illustration: DIAGRAM 19.]

    We can now advance another step and notice a frequently occurring fracture that is caused by the constant pressure and tuning up of the A peg, at a part which in many violins, owing to the peculiarity of design, is a very weak one, the grain of the wood above the peg being short and liable to overstraining by impetuous performers. Being one of the most inconvenient positions on the instrument for working upon, if the repairing is not effected in a methodical manner, it is nearly certain to come undone again. The crack is more often than not unperceived for a considerable time by the performer, and meanwhile grease and dirt work their way secretly into the pores of the wood.

    A repairer may take a glance at the state of the fracture, whip out some glue, paint a little on each side, wriggle the whole well at the risk of extending the wound, get in a little more glue, and let that harden under pressure from the cramps, which--unless extraordinary care and skill is exercised, damage other portions of the work--replace the peg and send the instrument home again apparently as sound as new (diagram 20).

    This treatment, if resorted to immediately after a sudden and clean fracture, may be effectual for some time, but if, as above mentioned, it has begun secretly and enlarged by degrees, the kind of repairing described will serve but a few turns of the peg, when crack it goes once more. Off to the fiddle hospital again, where it may be possibly subjected to a repetition of the treatment, especially if the owner is of an economical turn of mind as regards "bill of costs."

    [Illustration: DIAGRAM 20.]

    Under the above circumstances of combined age and dirt, some repairers would dare to increase the fracture or pull the scroll quite off in order to get at the part, cleaning it well before glueing it on again.

    This is making things worse, particularly as this part of the violin is one of the most awkward at which to apply direct strong pressure on a good and neat junction.

    Sometimes the first mode is resorted to with the addition of what is called bushing the peg-hole, that is, after the glueing performance has been gone through, it will last strong enough while the hole is being enlarged, a cylindrical plug of wood being inserted, and glued.

    This is levelled down and re-bored, to suit the peg or a fresh smaller one. This treatment is to be avoided if possible, as it is accompanied by a more or less disfigurement of the "cheeks" of the peg-box, and at the best is uncertain. A much more sure and neat method is, in the first place to clear all dirt and grease away possible, and gently work some clean water into the crack, repeatedly wiping with a clean cloth.

    When sufficiently done, some strong glue may be worked in, in like manner, cramps and pads applied and the parts brought neatly in contact.

    When the glue is thoroughly hard and dry, on the inside of the peg box extending each side of the crack and beyond the peg hole, a space must be cut away having straight sharp sides to the depth of about 1/16 of an inch, perhaps a trifle less. It must be done with keen edged chisels--size according to requirement--and the walls made as even as a piece of plate glass. Sometimes, in consequence of the shortness of the peg box, it will be necessary to make the cut away space extend further upward, and into the solid part. In all instances it will test the mechanical dexterity and patience for cutting in confined spaces.

    When this has been accomplished to satisfaction, a piece of maple without curl or knot must be cut a little thicker than what has been removed, but as to superficial area, fitting to a hair's breadth if skill will allow.

    Some old scrolls, particularly among the old Italians, are made of beech or other tough woods; in these instances the material must be matched according to the means at the disposal of the repairer. In cutting the small veneer of wood to be placed in position, care should be taken that when fitted in, the grain should run as nearly as possible at right angles with that of the part to be repaired. If this is attended to, with all other necessary precautions, there will be little cause for fear of the part going bad again, in fact it should be actually stronger than before.

    It may occasionally happen that both sides of the peg-box have been strained and split, with accompanying conditions of previous bad repairing and dirt. The same treatment will suggest itself for the "double event" as sportsmen say. But the two fractures are really as easily repaired--that is, with proper care and skill--as the single one. This is because the same cramps can be used for joining the two fractures simultaneously.

    For this operation the cut out space referred to close by, if not covering the peg-hole, will have to be repeated on the opposite side with great exactness, so as to allow of a single fitting up and filling the intermediate space, the grain running as described before, and which will therefore be--when placed in position--with the end of the grain towards the spectator--looking towards the front of the peg-box. It should be neatly and very closely fitted (diagram 21).

    In carving the blocks that are to be used outside the peg-box for evenly distributing the pressure, precautions must be taken not to cut them of equal thickness, or when the pressure is applied, they are likely to slip, particularly when the peg-box diminishes rapidly in width under the volute. They must therefore be cut more or less wedge like, according to the modelling or proportion of the parts, so that when placed on, the screwing of the cramp will be direct.

    When this is done to satisfaction, the usual process advised for the glueing may be proceeded with, and being carefully seen to be in proper order, the cramp with pads against the outside cheeks of the peg-box may be screwed on rather tightly. When quite dry, the cramp being unscrewed, the side block of wood will be found firmly adhering, with the superfluous glue squeezed up from between the surfaces by the pressure.

    [Illustration: DIAGRAM 21.]

    The next proceeding will be to level down the projecting parts of the block in front, to the line of the throat. This being accomplished with great neatness--the line of old work and new wood being exactly level, a line may be drawn with a pencil or cut with the point of a knife over the block as a continuation of the inner surfaces of the peg-box. If carefully managed the knife point is preferable, a piece of stiff card or very thin veneer may be cut to the width, bent over and the point run down each side.

    The advantage of the knife line is that you have already a cut to work up to. After this the chiseling out or mortising can be proceeded with. The tool must be very keen edged, and as the cutting has in great part to be done against the grain, no violence must be exercised; rapidity will only come with regularity in taking off thin shavings.

    When all the surfaces have been carefully pared down until, as regards thickness and evenness of line and surface, the peg-box is just as it left the hands of the original maker, there will remain to be done the clearing of the wood at each of the peg-holes which will have been covered by the block perhaps wholly or more than half way. In the case of the double fracture this will be found to be in the same condition on both sides. The hole will require continuing through the fresh wood, in fact re-boring so far as this is concerned.

    It will be a more or less delicate operation to prevent splitting the wood, especially if from shaving down to the surrounding levels, it is not very stout.

    To guard against catastrophy, a small hole should be bored exactly in the centre. Particular attention must be paid to this, or the whole work may be spoilt and a fresh block or bushing of the hole be found necessary, and much of your work to be done again. The small hole may be drilled if you have the necessary means at hand, if not a small brad-awl may be used, not of the usual round kind, but square. Such brad-awls are, I believe, known as chairmender's brad-awls. If one cannot be obtained, an ordinary round one can, with a little trouble, be filed square.

    The advantage of this form of awl is that it does not split the wood and can be used with safety and certainty where one of the ordinary pattern would be certain to split and spoil the work.

    Several sizes may be used to enlarge the aperture, the square edges breaking away the sides without causing an extended crack in the direction of the grain. When sufficiently enlarged, recourse may be had to the rat-tailed or circular file. Here again much care must be taken, as the toothing of the file is arranged somewhat in the fashion of a screw, and if the tool is used one way it soon buries itself, becomes tightly wedged and will inevitably split the surrounding wood.

    It must therefore be turned in a direction that may be called backward, the revolutions to the left instead of to the right. It will take a little more time than might be expected, but the result will be more satisfactory, free from danger of splitting and the interior surface of the hole be made smooth. The use of one, a degree or two finer in tooth will give enough finish. A constant look out must be kept that the tool is working properly in the centre; should it be found working a little too much to one side, it must be removed and the opposite part gently cut away by a slender sharp knife so that the equality may be restored.

    Caution must be exercised that the action of the tool is arrested at the right moment, that is, when the opening made in the fresh wood is worked closely up to that of the old; the tool should not be allowed to work against the walls of the old aperture, as there is much risk of damage or enlargement and the necessity of a fresh peg, which is to be avoided, if the set of pegs have been doing their duty well and are free from splits.

    In the fitting of the peg, a degree of tightness into the new wood will be found advantageous; the surface being fresh and softer than that of the old, soon accommodates itself during the insertion and revolution of the peg, whereas the process will have been going on a long time with the old walls which have become hardened.

    After a few turns with the inserted peg, the fitting of it will have been tested, and if satisfactory, it may be taken out; a piece of soft chalk stroked down and followed by a piece of very dry old soap in the same manner at the parts coming into contact with the interior walls of the aperture and will stop any squeaking or catching. The proportion of soap to chalk must be varied, the one, soap, being increased according to the catching or jerking and lessened if there is too much slipping and no grip. It may be as well to note at the same time that the peg should be quite circular, or it will revolve by fits and starts notwithstanding soap and chalk, or any other mixture.

    CHAPTER V.

    FRACTURE OF PEG-BOX AND SHELL--CHIPS FROM THIS PART--FILLING UP OF

    SAME--RESTORATION TO ORIGINAL FORM, AFTER PARTS HAVE BEEN LOST--WORN

    PEG-HOLES, RE-FILLING OR BORING SAME.

    We may now take another degree lower down and study the treatment best for a fracture similar to that last described, but which, if at one of the lower peg-holes, may appear quite as difficult to manage, if not more so, as at the upper part, in consequence of the curved form of the shell or lowest part of the grooved back of the scroll. Firstly, the cleansing must be effected and drying, as previously with the upper fracture, bringing or pressing the parts together for testing their accuracy of fit. The cramp must be again brought into use.

    Owing to the wider and deeper hollowing of the back at this part and the longer and often very unequal continuation of the line of contour, the shell or tail end sometimes curling up more abruptly than usual, an increase in the substance of the padding against the cramp will be found necessary. A piece of cork cut or filed to the shape will prove handy and effective.

    The superficial area of the interior walls of this part of the peg-box being much greater, the thickness ditto, there is seldom a necessity for fitting a block of wood in the manner before mentioned, unless as sometimes it is found, the part has been so worm-eaten as to be too weak for its work of supporting the pegs and sustaining the strain of the strings. In that case, excision of the "honey-combed" part is obligatory and a slice of wood must be let in as before explained.

    Sharp shaving with a minimum of force will be required. Should the worm-eaten portion extend to the outsides or "cheeks" of the peg-box, it would be well to insert here also another slice of fresh wood as before, the length according to requirement, but in these instances, the portion of the head piece under consideration being lower down and broader, the grain of the inside slice may run continuously with the original wood. It will also be inserted first, and not until the glue is quite hard will the arrangements for the outer one be commenced.

    Especial care will be required in the management of the cramps--one or two may be necessary--as, if mere padding is placed between the iron and the wood, the latter, being in a state equivalent to rottenness, will be crushed together and the shape will be ruined.

    As a preservative against accident a piece of soft wood, perhaps a quarter of an inch in thickness, and cut in width and shape equal to that of the "cheek" of the peg-box, and placed over the part with a piece of paper against the varnished surface, will enable the rotten portion to keep its form, the pressure being distributed; care must be exercised in carving the block of wood that it reaches over and quite on to the sound parts.

    When the glue has hardened perfectly and the cramps have been removed, the careful shaving down and finishing of both the inner and outer blocks or slices may be proceeded with.

    If the burrowings and tortuous course of the obnoxious depredator give indication of its having been of huge proportions for its species, for these creatures vary in size from a small pin to nearly an eighth of an inch in diameter, and the tunnellings are not very close together, then pieces of fresh wood matched carefully and fitted in the manner before described, must be inserted and glued in. This will, if the wood is much riddled, be much like mosaic work, the fitting in of the pieces running here and there over the surface.

    The contour, however, is preserved by this treatment, it being difficult, unless the repairer has considerable artistic knowledge, to keep or reproduce the exact form if the half or more of the peg-box and adjacent portions are cut clean away as is often done.

    Scrolls of masterly design and execution are frequently met with mounted on a peg-box, selected or carved, without the least reference to the style of the original, imparting to the whole a hideously mixed and vulgar aspect. Save then, every morsel of the original work that you possibly can, especially if it be the work of old Italian makers, as it will be sure to have about it some points of interest, or that will call for your admiration of its artistic merits. Bear in mind that at the present day utility and low price are "to the front."

    Unfortunately for art, a very large section of the public called musical, ignore the artistic aspect of the violin, apart from its individual authorship and monetary equivalent, and think almost solely--not always in the right way--about its working or sounding capacity.

    To them one sort of curled heading to the peg-box is as good as another, if strong enough, the whole of this part of the mechanism being simply dedicated to the winding up of unwilling "catgut." The old masters, their pupils, and modern imitators, have thought otherwise and treated this portion of the structure as that in which they could concentrate much of their best artistic talent. To them it has been the crowning head piece of the work, and requiring for effect the closest attention in detail.

    Every part of it has received, by each master, a distinctive touch of tool, or conception of design, that the modern repairer should earnestly "read, mark, learn, and inwardly digest," so that if a small portion is by carelessness, or unavoidable accident, chipped off, the contour may not by restoration (?) be spoilt, or the flow of line ruinously disturbed.

    Some remarks might be made by some admirers of high finish in its simple sense, about the bold unfinished gouging of some of the old Italian makers, and queries whether the irregularities should be studiously followed up by the repairer, as it should unquestionably be with work of high refinement and minute finish.

    The answer is at once simple and conclusive, every part that can be preserved should be so, and well studied, that the new work may be a continuation of the old to the minutest detail, even to the accidental emphasis of tooling left by the maker.

    The fact must not be overlooked, that rough as some work looks at a glance, it has been, by masters of their art, properly thought out beforehand. Rapidity of execution, coupled with fine artistic style, is not to be acquired within a short space of time. In most of the apparently rough hewn scrolls of the Italian masters there is to be seen the result of experience in cutting, perhaps, hundreds of them previously.

    If we examine closely the mannerism of the different schools with regard to that seemingly insignificant termination of the back grooves called the shell; the different ways, breadths, depths and direction of the gouging will be found to give, not only an accurate indication of the country, or city, in which it was carved, but with it the school, or style to which the maker belonged, besides his own individuality.

    As a landmark for distinguishing these interesting particulars, every part of the scroll of an old master, with its belongings, no less than any other part of the instrument, should be treated by the repairer with much reverence for its age and respect for the talent expended on it in course of its construction. That this is not always acted up to I am reminded by an instance that came under my personal knowledge many years since.

    A repairer and maker of some experience was examining a violin by one of the old Italian makers, that had, underneath the shell a rather sudden demarkation at the part where the graft had been fitted in. He remarked to the party who brought the violin, that if it were his own, or had been requested to put it in good order, he would file or glasspaper down the edge round the lower part of the shell, so as to make it conform with the modern work. The violin was not entrusted to his care, nor do I think many others were, judging by after events.

    Trust not any violin of value or interest to this class of repairer, or grief will count you for its own and mortification that of the fiddle.

    Occasionally small pieces get chipped off the lower rim of the shell; the latter under these circumstances, as before observed, should never be rubbed smooth with glasspaper or cut down. It is not a difficult position to get at and small pieces can easily be inserted. This part also is so fashioned that a comparatively small loss of the edge, especially at the sides, will alter the whole character and reduce a most elegant and masterly form to that associated with mere rubbish.

    Three or four scrolls of Stradivari's are in my recollection as having been under such treatment and the contour being destroyed there was little about the general shape to remind the spectator of the beautiful design as it left the maker's hands. But, it may be remarked by a fortunate discoverer of an old gem, my Amati has lost all this part, cut away perhaps because of its being quite past recovery, and the question arises what had better be done under these circumstances?

    The answer, seek some party who has an Amati with this part perfect or in excellent preservation. Take some moderately firm veneer and after careful measurement cut pieces to fit as exactly as possible the parts answering to those of your own instrument that are missing. The line from the lowest part or edge of the shell and reaching right over the top of the scroll will require earnest attention and accurate fitting.

    For the next stage the pegs must be taken out as a matter of course.

    Number each one with a pencil for identification when reinserting; lay a piece of veneer flat on the outside of the peg-box reaching up a little past the top of the scroll; to do this nicely a segment should be cut away where the volute intervenes, and with the pencil, mark carefully on each side a line neatly against the back and front. With a sharp, narrow knife cut away the veneer up to the outside of the line, leaving, if cleanly done, an exact pattern of the throat or exterior of the peg-box (diagram 22).

    Next, as the veneer will not bend sufficiently, cut a piece of rather stout paper, and after laying it against the back of the scroll, a rough tracing can be made and cut to exactness by degrees, trying it against the model and correcting until satisfactory.

    As this part of an Italian violin is not cut so mechanically as many people imagine, another and perhaps quicker way, if means are to hand, is to use thin paper and with some heelball, used by shoemakers, rub the edges that may be felt through and under the paper held in position against it. If the paper is kept from shifting a very good clear line can be obtained. The process may be adopted for the other parts instead of using the veneer, the latter would, however, be useful as a permanent guide or template, keeping its shape. This would not apply of course to tracing of the back part, which must of necessity be of a material that will bend or fold over.

    [Illustration: DIAGRAM 22.]

    Having procured a piece of sycamore, very old if possible, and with the closest resemblance in curl, texture and colour to the scroll to which it is to be attached; it must be squared up and made equal so that the tracings of the two sides of the throat may be placed in position and transferred. This must be done so accurately that the new throat shall not be out of the square or twisted. More, of course, will be traced down than will be actually left, the reason will soon be perceptible. If the tracing is clear and well defined it will not require touching; but if any part is not well brought up, it may be made sufficiently so by carefully running a pencilled line over the fainter one.

    The next step will be to get rid of the superfluous wood.

    This will be most readily done by a bow-saw after securing the block of wood in a vice, if these are not within reach, it can be done at a sawing mill where steam saws of different sizes and degrees of tooth are ready at a moment's notice and the removal of any sized masses of wood hard or soft is effected with remarkable precision and rapidity.

    When the sawing is complete, the fining down, or smoothing of the sawn surfaces may be proceeded with. This may be done with a file, having one side curved, the other flat, and of rather fine tooth; a glass papering will then complete the process so far as the profile view is concerned. Further progress will be made when the tracing of the back is transferred, the paper pattern being laid, or wrapped round, after being accurately adjusted.

    The outside wood can be removed in the same manner as last described, with the finishing, or semi-polishing to the required degree. There will be thus cut out a replica in the solid or uncarved state of the whole of the part adjoining the scroll and downwards, which will be ready for the further process of joining on to the scroll itself.

    To this end, the surfaces that are to be glued together at the junction will have to be got into proper shape and condition, that is, both pieces must have flat faces, that when put together, will allow the line at the top of the scroll to run continuously and truly as if forming an original carved homogeneous work. The faces must be cut by a very sharp chisel, until fitting as nearly air-tight as possible. For highly finishing off these parts a small steel scraper should be used and turned round, working it in several directions.

    If the scraper is quite straight and sharp, it will with gentle handling bring the surfaces very flat, no movement or wriggling being perceptible when placed together, or there may be in very good work a slight kind of suction by the air being driven out from between them. The work will be then ready for glueing. The wood should be quite warm, the glue fresh and strong. A few seconds or so may be well spent in brushing or working the glue into the pores of the two surfaces to be opposed.

    If they are as perfect, or true as possible, a little rubbing together will be sufficient for an effectual and lasting junction without the use of cramps; but if there is any doubt on the subject, then the process described previously for joining the parts together after fracture had better be gone through.

    When the whole is thoroughly dried and the glue which has exuded from between the opposing surfaces has been cut or chipped away, the gouging of the grooves down the back may be commenced, care being taken to follow the lines from the scroll downwards and gradually finishing backwards and forwards according to the grain. Different sized gouges will, of course, be required for this work, according to the fashion or type of the violin. A glass papering of the parts will complete the matter so far as the exterior is concerned.

    Some restorers might recommend the glueing on of the scroll to be proceeded with earlier, or before the block has been finally reduced and cut to shape. There is not very much preference one way or the other; in the one above detailed we avoid the risk of fresh damage to the scroll while sawing and cutting, the rough or more violent tooling being done before the junction is effected.

    It would be as well to let the new wood be of full measurement to allow of fining down the new surface to meet that of the old, which may possibly have some lustrous varnish upon it, and which every good restorer would do his utmost to preserve. After this is all satisfactorily done, the lines may be traced which are to act as guides for the hollowing of the peg-box.

    For this purpose a rather small chisel of the kind known among cabinet makers as a mortising chisel will be required. Gently and by degrees the mass of superfluous maple will have to be removed. It must be borne in mind that maple or other tough wood will not bear the forcing that a piece of pine will. A hard-wood workman is essentially a man of degrees, the tougher the wood the less must be shaved off at a stroke.

    The strong, massive form of the mortising chisel is used in order that there may be as little spring as possible in it while cutting and so prevent a hacking of the parts instead of a clean cut surface; indeed, no other proportioned tool can be used with any degree of facility.

    It must not be ground to a very acute angle, or the objections that are sought to be avoided will reappear in another form. Great care must be taken that the mortising does not extend to a depth that will cause the back to be thin and weak. This mistake is often seen to have been committed in very valuable instruments, especially such as have the two grooves deeply modelled, or the contour downwards from the volutes is much indented.

    At times, on the other hand, sound judgment has been perceptibly directed to this part and instead of cutting away wood to allow of freedom in the winding of the strings over the pegs, the holes for these have been filled up and re-bored nearer to the front edges.

    Many most excellent old Italian makers seem to have been rather careless with regard to the exact position of the peg-holes, making them to be equi-distant from each other. There might have been little or no objection to this in the days when the strain on the pegs was not near what it is in the present times of very high pitch. The shaft of the old pegs used in Italy at the time of the great masters, was not half as thick as is thought expedient now. Towards the latter end of last century and the beginning of this, more attention was paid to the matter, and we accordingly find the two upper peg-holes much closer together and the two lower ones ditto.

    Concerning the refilling or "bushing" as it is termed of the peg-holes, a few words may not be out of place. For the purpose the holes must be enlarged more or less or there may not be sufficient of the new wood to hold together when the re-boring takes place. The cutting must be truly circular and very sharply done, no tearing of the wood must be perceptible, but a clean, almost polished surface inside. A solid cylinder must be cut with great exactitude, of maple or the same kind of wood if obtainable as the scroll.

    The old makers did not invariably use maple, perhaps being unable to obtain it in sufficient quantities for their business purposes. It is useless to think of cutting the cylinder or rod any other way than with the grain, it is seldom if ever done, and moreover involves an expenditure of time and labour that brings no adequate return. The enlargement of the hole must be effected by a good form of tool and this in good condition; peg-hole cutters and fluted rimers are sold for the purpose.

    When the cylindrical rod is cut and rounded to make an exact fit, a portion can be cut off a trifle longer than will be apparently necessary so as to allow of finishing off. If satisfactory in all respects, recourse may now be had as to the solution of glue, which should be quite fresh and strong, as this is to be for a permanency. The rod or portion should be warmed if the season is cold, the glue allowed to settle round for a moment while some should be placed on the inner surfaces of the hole in which the cylinder is to form a solid fixture.

    When inserting the cylinder it should be worked round a little, but not jammed in with violence.

    Your reliance in repairing must not be in force but accurate fitting.

    The opposite hole to be used for the same peg must be made and treated in the same manner. Some repairers, for economy of time, would make a fresh enlargement right through the two opposite holes and push the rod through both and glueing same at one process, cutting it away from the interior of the peg-box when the glue has hardened, but this is risky work. One hole is sure to be larger than the other and the fitting scarcely likely to be accurate both sides.

    When a sufficient time has elapsed for the glue to dry, a piece of hard, but not too thick, cardboard should have a hole made so as to allow of placing on the projecting part of the rod, which can be now sawn off close to the card. When this is completed and the card removed, a sharp flat chisel will then reduce it to the absolute level of the surrounding plain.

    The next stage will be that of re-boring a fresh hole in a proper position. This must be carefully calculated, so that when complete the whole of the four strings will be independent of each other, the A string not being in friction with that of the G or the D not touching the E. If this is not attended to, much trouble will be given to the performer, the jerking or catching of the string during the winding up, not being caused by any difficulties with the fitting of the peg itself but by the string pressing on and being checked by the peg of another.

    The boring of the fresh hole and fitting of the peg is of course a similar operation to that just described, with the difference that the peg must be more conical, whereas the plugging must be as near equal in diameter as possible along the whole of its length. The preparation of the fresh peg to fit the new hole will be already evident as to its requirements. There is one detail to be noticed, however, that of boring the hole for the reception of the string. Of course the E will not require so large an aperture as the D.

    The latter will require the largest aperture of the four. If this operation is not conducted in a methodical manner, with a proper knowledge of the best treatment according to the material used for the peg, splitting will ensue, which is trying to the temper. When a peg is once split it had better be thrown aside as useless, the strain on it being unsupported by the solidity of the material. No wooden peg that has been split in the operation of boring for the string should be retained.

    It being necessary to use wood of the hardest or toughest consistency, the splitting tendency is increased as the grain is closer. There is discussion as to the best material for pegs, and here in my opinion the old Italian makers were wise in choosing the cherry wood seemingly abundant enough at their command. It is not so hard and brittle as ebony.

    Another wood was used by them, a kind of dark walnut, straight in the grain, but a little firmer than the rose wood so fashionable at the present day, which has a waxy consistency but accommodates itself to the jamming by the impetuous amateur who will have his way.

    CHAPTER VI.

    LOOSENING OF JUNCTION OF GRAFT WITH PEG-BOX, AND REFIXING

    SAME--GRAFTING, DIFFERENT METHODS OF PERFORMING THIS--LENGTHENING THE

    NECK--OLD AND MODERN METHOD--RENEWAL OF SAME--INCLINATION OF NECK AND

    FINGERBOARD WITH REGARD TO THE BRIDGE--HEIGHT OF LATTER, AND REASON

    FOR IT.

    In our progress downwards from the scroll and its adjoining parts, before quite leaving it we may refer to a disorder sometimes occurring when the neck is modern and grafted on to the old scroll. There are several ways, or fashions it may be termed, in which this is effected.

    The most usual method pursued in England and Germany is that of sawing the head off at a part below the end of the shell and then chiselling a level passage so far as a straight surface makes it necessary along the floor of the peg-box. The sides are treated in the same way but the width across diminishes as they proceed upward. The solid graft is shaped, inserted, and afterward hollowed, but of this more presently.

    Like all other parts of the instrument, the junction or insertion of the neck or graft sometimes gets loose, from bad fitting chiefly, bad glue or prolonged exposure to damp. When the sides or back part give warning that they are likely to part, they should be loosened still more or separated and a little clean water on a brush inserted in the cleft where discoverable, the parts being pressed and worked together until clean, for all cracked or loosened joints will be found more or less dirty and greasy.

    Some strong glue can be then worked in, both sides pressed together by cramps and left to dry. The backing of a flat piece of soft wood with an interleaving of stout paper or, better still, millboard, must not be forgotten. If, as sometimes happens, the flooring of the peg-box threatens to part from the graft in contact, the same course of working out dirt and inserting good glue must be pursued.

    In pressing the back or shell of the scroll, this being of short and sometimes abrupt hollowing, the pressure on the substance of the wood direct would be dangerous to its form. The fibres of the wood at the edge are necessarily very short and brittle. A thick piece of cork should, therefore, be placed between the cramp and the hollow grooving or shell, a small block of moderately hard wood being placed inside the peg-box as an opposing pad or buffer, the cramp may then be screwed down fairly tight.

    The two operations, glueing and pressing the side parts and that in connection with the shell, must not be attempted simultaneously.

    We may now, being on the part as it were, take up the subject of grafting and the different and best means of performing this somewhat exacting operation. Accurate calculation and sharp straight cutting are absolutely necessary for even moderate success in this undertaking.

    As before mentioned, there is more than one method of securing a neck to an old head. Each one carried out with the necessary skill and neatness can be made a lasting and highly finished piece of joinery.

    The mode adopted in England (see diagram 25) is the most ready and gives the least difficulty in a difficult undertaking. The solid end of the graft is chiselled or planed off to a slightly wedged form with a straight or square upper end which is measured to reach when inserted, nearly or just up to the lowest of the upper two peg-holes. Great care has to be taken in the cutting that the sides are equal, otherwise the scroll, when fitted, will look awry.

    [Illustration: DIAGRAM 23. Old method of lengthening neck, the dotted lines show it shifted forward and the part above the button cut away.]

    [Illustration: DIAGRAM 24. Modern French method of grafting head.]

    [Illustration: DIAGRAM 25. Modern English method of grafting head.]

    [Illustration: DIAGRAM 26. Foreign secret method of grafting occasionally met with.]

    [Illustration: DIAGRAM 27. Method occasionally met with, Italian.]

    Another method has been known as the French, and when neatly done is one of the most sparing of the old wood (see diagram 24), but it is beaten in this respect by another foreign method (diagram 26), which is less evident to the eye, although requiring more skill in accurate cutting and adjustment. Another yet more secret I have only seen in an Italian grafting, and it may be native; no join whatever is seen in a front view nor in the peg-box if this part is at all soiled or dusty, as is usually the case.

    This is owing to the join--there must be one of course--being each side at the angles formed by the walls of the peg-box. This is counterbalanced however by the necessary cutting away of the central line or ridge at the back for a considerable distance. If done accurately and artistically, all very well, but this is not likely to be always the case, although a comparatively easy bit of work with the original lines each side as a guide.

    This method of grafting is puzzling when successful, as little or nothing is perceptible from the front and not much, unless searched for, at the back.

    On measuring the different parts of an old violin in its original condition, we shall find the neck, taking from the edge of the upper shoulder of the instrument to a point where the nut is placed, to be not much more than four and a half inches, whereas our modern necks measured at the same parts would give five inches and an eighth. The old length taken at this part alone would give too short a fingerboard, causing the fingers to hamper each other, especially in the upper part of the register, where so many modern composers seek for effective passages.

    The neck must, therefore, to meet the requirements of the day, be lengthened. In the earlier part of the present century there was a method much in vogue for effecting this without interfering with the head and while keeping the greater part of the original neck (diagram 23).

    This was done by firstly removing the fingerboard, probably worn into ruts; the middle of the thickest or lowest part of the neck attached to the body had then to be loosened and removed, often no doubt a troublesome task owing to one, two and sometimes three nails being in the way, this in consequence of the habit of the old makers of attaching the neck with its scroll before closing up the body of the violin.

    Having accomplished this, the repairer chiselled off two square pieces, one on each side at the same end, and then fitted longer blocks with the grain running the same way. These were afterwards cut down to the proper form, so that the terminating part under the fingerboard increased the length of the neck to the modern standard.

    Of course, when fitted into the original space or socket from whence the neck was taken, the rounded part going to or above the button was now too large, this part was therefore cut, filed and finished down to the required size and shape.

    This method of lengthening the neck, however, went out of fashion as connoisseurs and performers, finding the old necks so frequently devoid of figure--the reason being probably that plain wood answered best for the cutting of the volutes--made the repairers remove the whole of the neck and substitute one of the best figure they could obtain.

    This forced fresh attention to the splicing as it is termed of the scroll to the neck or graft, and the method has continued to the present time of clearing away the whole of the neck and using handsome wood.

    Further impulse was given to the practice by the fact of the fingerboards put by the old makers rising so little above the body of the instrument. The bridge was made very low to accommodate this state of things. The increased rapidity of the movements of the bow from one string to another over the middle ones in the performance of modern music made a higher one absolutely imperative, as the heel of the bow would too frequently chip pieces from the waist curves. There were thus three good reasons at least for placing an entirely new neck on an old violin; firstly the plain wood of the original maker, shortness and the low angle with regard to the plane of the body.

    In order, therefore, that everything may be accomplished with sufficient exactitude, we will begin with the roughly sawn block ready for measuring and shaping up for its destined purpose. The scroll, which is to be replaced on a neck according with modern ideas, we will suppose to be on an Italian violin that has come down to us from the early part of the last century. The violin tuned up to the present concert pitch and music of our period having many of the modern style of difficulties, would prove utterly inadequate to the task of giving out its tones in a manner expected of it.

    In proceeding to work then, the workman executing this modification having selected his block of curled maple, planes it to an oblong of equal breadth. He calculates as to the best position for showing off the curl on each side of the neck when finished. Having decided which is to be the upper part or that covered by the fingerboard, this is planed to a good level and smoothed. A line drawn with a good pointed pencil or pointed knife, and sharply defined, is then drawn down the whole length exactly in the centre.

    At the end which is intended for the thickest to be inserted in the body of the instrument an equal width each side must be marked. Near the other end, at a distance that shall correspond with the opening of the peg-box, an equal width each side of the line must be marked off as at the other end. These two measurements will represent as nearly as possible the width of the neck along its course at the junction of the fingerboard.

    From the point representing the opening of the peg-box one of two lengths upwards must be decided upon; if the splicing is to be effected in the manner common in this country, a greater length will be required than for that of the French style. This latter is more to my fancy than the other, as there is less of the original wood lost. If for the former, a length of wood beyond the opening will be required of two inches, if for the latter or French a little over one inch and a half will be enough.

    The central line has of course been continued for the whole length of the wood. The waste wood at the end can now be sawn off down to the line.

    The next measurement will be, supposing the French style is adopted--that of the extreme width of the end, which will be given by taking a point at half the thickness of the peg-box wall at the part and similarly placed on the other or opposite and taking the width between the two. This divided equally and marked on the wood of the new graft each side of the central line will give the narrowest width of the part to be inserted in the peg-box. The outside may be then removed by the saw vertically.

    There will now be necessary the marking off a part on the graft that shall represent the thickness of the nut or the distance between the end of the fingerboard and the peg-box opening; the breadth across, or we may call it the length of the upper part of the nut, will be exactly that of and at the part where the opening will be made in the peg-box for the reception of the graft.

    The wood to be cleared away outside the lines which mark the width along the course of the fingerboard will be the next proceeding; it may be done neatly with a rather fine toothed saw and then carefully planed up closer to the lines, barely touching them. It is preferable to leave the sides for the present at right angles with the top surface, although they will not be kept so for long, but by thus working the measurements are facilitated.

    Going to the lower or wider end a line must be accurately marked quite square with the long central line, if not accurate the whole work will be thrown out of truth. On the sides there may now be marked and roughly sawn away (diagram 28) so much of the wood that shall leave enough for the cylindrical part that is to be finally rounded and finished off for handling. Care must be taken that the rounding commences underneath, a little away from the part that will be fitted into the peg-box.

    This of course must be according to measurement or template kept for the purpose if graftings are likely to be wanted in the future. There will now be required the marking of the exact form of the part that is to be inserted in the body of the violin, or more strictly speaking, into the upper block. This is done easily from a pattern cut to shape and size for instruments of average proportions.

    Sometimes, owing to the height of the ribs, the pattern cannot be applied so as to fit; in that case fresh lines must be drawn to measurement as with the central one on the fingerboard plane.

    [Illustration: DIAGRAM 28.]

    The line dividing the part exactly in the middle must be accurately done, the distance at the narrowest or lowest part that is to be glued on to the button carefully marked, allowing the top part when placed in position to be a quarter of an inch above the border (diagram 29).

    The width of the lowest portion must be mainly guided by the size of the button, which, although there is an average of a rough kind, is sometimes small, at others very wide. The width must be taken of the button, carefully divided into two equal parts to be marked on each side of the central vertical line (diagram 30). All below what is necessary to keep may now be cut away, the surface being kept parallel with the fingerboard plane. The parts outside the slanting lines may be hewn away, the surface running evenly with the outer lines of the fingerboard width so far as it extends, which will not be more than about an inch.

    [Illustration: DIAGRAM 29.]

    [Illustration: DIAGRAM 30.]

    The next process will be that of excavating the part that is to receive the root or end of the neck. If the instrument has been accurately constructed with the join running down precisely in the centre, the line already marked on the root of the neck will be a safe guide for marking each side of the join the width of the portion to be cut away.

    The depth inward of the cutting should be an average of a quarter of an inch. In case the already excavated part in an old and much repaired instrument is roughly torn about and made unequal in its measurements, attention must be fairly directed to this part separately; that is, if too much wood has been cut away on one side it must be replaced by fresh, after clearing away irregularities in order that a good fit may be accomplished.

    The fresh wood must be neatly inserted or placed in position and may be held in position during the hardening of the glue by supports or wedges placed across from side to side. When quite fit by reason of its dryness, the distance from the centre must be marked and the fresh wood cut away to the required depth and width with a keen edged chisel and small shavings cut at a stroke, as there will be some cutting against the grain to be done besides working in a confined position.

    Great regard must be paid during the process of cutting this part that the corners or angles are quite cleared out, or the neck when inserted as a trial or rehearsal will not give a truthful report of the accuracy of the incisions owing to some insignificant portions sticking up and causing the neck to look awry. So far we may take the fitting as having been accurately done to the central line down the middle of the instrument; but now comes a further process in connection with the adjustment of the neck, and that is, the rise and inclination of the level of the fingerboard in relation to the bridge which is to be fitted eventually.

    The average--it may almost be called the standard--height of the violin bridge is one three-eighth inches. There are occasions when this measurement may be departed from, as in the instance of a high model, when an eighth, or even more, may be taken off with advantage. This must not be taken as necessary for the proper emission of the tone from a highly built instrument. The raising of the bridge in modern times is due to other causes, the most important being that of allowing better play or room for bowing rapidly over from side to side without rasping the border at the waist. It is an alteration which accompanied the lengthening of the neck and stop in the early part of the last century.

    To obtain a proper setting or inclination of the neck, several ways are adopted by repairers. They vary according to the kind of guide or pattern used. This is usually cut from a piece of hard wood, sycamore or pear. It is sometimes made as a double guide in the adjustment of both the inclination and the elevation of the under part of the fingerboard above the body of the instrument at the junction of the neck. This we will call No. 1. The other, No.

    2, is similar, but has the height of the bridge only as a fixture, the rise of the end of the neck above the border being higher and lower at discretion. Another way, No. 3, is somewhat like No. 1, but would be used when the fingerboard is glued on before the setting. This should only be done by a fitter of some experience, as a little error in calculation is likely to lead to disaster.

    With each the application of the guide, or pattern, is the same, namely the testing of the exact coincidence of the inclination of the top surface of the bed under the fingerboard (diagram 31), or above the latter as shown in diagram 32. While getting the right inclination, in both instances it will be found necessary to ease the fitting of the neck into its socket, as the difference of the angle at which the neck is inserted causes an increase in the tightness of the contact of the parts.

    The lower part of the facing that is to be inserted in the socket, will have to be made to go into it at an angle conformable to that of the inclination or set of the neck. This will require executing with precision, and great care will have to be exercised that the squareness or rectangular disposition of the upper part already fitted and adjusted to the middle line down the instrument is not interfered with. It will be well to test this as the work proceeds.

    Some of the lower part, that coming into contact with the button, will have to come away in order that all parts may fit, and when fixed, form a homogeneous rigid part of the structure.

    [Illustration: DIAGRAM 31.]

    [Illustration: DIAGRAM 32.]

    To ensure complete success in all the foregoing operations, every tool in use must be well sharpened, and all the guide lines accurately drawn.

    Part of the neck left rough and projecting beyond the button may be left for future manipulation, but the joints that are to receive glue--if done by a workman of skill and experience--will fit almost air tight. With regard to this, the parts likely to give the amateur most trouble will be the exact fitting of the flat opposing surfaces of the root or squared end of the neck or graft with the socket. It will be necessary to get a perfectly flat surface.

    In the first place, glass papering must be avoided, not from unsuitableness of material, for in that respect it is a temptation, but from the difficulty of regulating the pressure of the hand; with the exercise of the utmost care in handling the glass paper, even when it is backed by a piece of hard wood, there will be found, when the test comes, a rotundity of surface that was deemed impossible under the circumstances. Careful scraping of the surfaces must be chiefly relied on for exactness.

    As good a mode of proceeding as any is as follows--after the first roughing into shape and then flat chiselling has been done to as great a nicety as possible, all the irregularities--there are sure to be some--can be worked down with the edge of a straight square file, used very steadily and crossways repeatedly. This done sufficiently and tested with some hard and truly cut substance, metal preferably, will be an exactly flat surface for working upon the final or finished surface.

    The next thing used will be a carefully sharpened and keen edged steel scraper. To put this tool into proper order for the purpose, it must be sharpened on a hone, not exactly at right angles, as the first impulse would suggest. The hone, or stone, must be quite flat and unworn.

    If done carefully, a nice level edge will be perceptible along its course, but it is not yet at its best. Placing it on a bed of hard wood, or evenly shaped mass of iron, projecting over and held firmly in position, a good stout brad-awl may be passed along from end to end, keeping the awl perfectly flat on the horizontal surface.

    The scraper may now be turned over and process repeated, but not in the same manner or angle, for the awl will be held vertically with the handle downwards and firmly pressed along the edge at right angles with the horizontal plane, this will cause a burr right along which will have a razor-like sharpness and cutting power. This scraper can now be applied (not too heavily) over the filed down surface, and thus work down finally all irregularities left by the file.

    The adaptation of this tool will at once be perceptible in the fine whitish soft shavings that will come off during its application. A little repetition across and across should give an almost perfect level. Different sized scrapers may be used for the other surfaces where it is desirable to obtain the most accurate fitting. If all the processes have been properly carried out, the parts when tried by inserting the neck or graft for trial, should fit together without the slightest looseness or wriggling.

    They will now be ready for permanently glueing together.

    It will be seen after perusing the above that the fitting of the neck or graft to an old violin, well or badly preserved, is a task not to be overcome easily and satisfactorily without much care and no little practical experience.

    The whole of the work must be well looked over and tested as to the accurate fitting in all respects; nothing must be left uncertain or loose; in fact the flat surfaces for a perfectly successful result at the junction of all the parts should be as nearly as possible air-tight.

    Having seen that the glue of good quality is strong and clean, the surfaces that are to come in contact may be brushed over with it. For this purpose a small hog-hair brush of about three-eighths of an inch wide is handy. Where the grain or threads of the wood run parallel with the surface--this being less absorbent than the other parts,--there will be less painting over required, but where the grain comes end upwards to the surface the glue will be rapidly absorbed.

    The painting over these parts must be repeated, the glue as a matter of course being kept warm--all the work ditto, until absorption ceases. This is a matter of some importance, as in many instances joints have become loose or broken apart, not from the perishing of the glue or damp, but from the want of this precaution on the part of the repairer during this preliminary proceeding.

    It must be borne in mind that this is to be a permanent junction, not to come apart from any jarring or rough usage; it is also to be one of the most rigid, and only to be separated by a saw or chisel in the hands of some future repairer when it shall be absolutely necessary. Sufficient glue having been applied the work may be put aside.

    It will now be apparent to those who have possibly done a little glueing that the whole of the wetted portions have to some degree swollen, and therefore if the junctions were brought together they would be found too tight and refuse to meet. Just so; and that is one of the reasons for placing the work aside until the glue has dried at all the parts painted with it. When after a sufficient time has elapsed the work is examined, it will be found to have contracted to its old size and form.

    There will not be the necessity for waiting till the glue is at its hardest; probably time will not allow of this, some days being absolutely required, but it must, for the next process, be very firm and seemingly dried through.

    Examination will reveal the fact of the whole of the surfaces that have been wetted, being raised or roughened under the foregoing operations.

    Recourse must now be had to our small scrapers again. These will again be applied carefully across and across the surfaces, until, in the judgment of the operator, the surfaces are level and clean. Particular care must be taken with the edges, angles and corners, that the superabundant glue is removed.

    The right angle of the scraper will be used for this purpose, and should a small particle or two, at any angle or corner, refuse to budge at the request of such a light tool as a scraper, the powers of a sharp chisel must be brought to bear upon the subject, and the obstacle removed. Close attention should be paid to the above, as in the operation of first glueing, the wood, or woods, having unequal absorbing powers, will swell in accordance therewith, and upset the calculations that have been so carefully made for the close junction of the parts.

    For first rate work, the scraping must be so carefully and accurately done down to the surface of the different parts, as to leave little or no glue above the surface of the wood.

    The desired result will thus be secured, that of the pores of the wood being closed or filled up. For the next stage the glue will not be necessarily quite so strong, a degree weaker will do. Everything must be ready to hand, including a cramp of sufficient size and strength.

    Before proceeding further, however, the manner of the application of the cramp must be considered. And now, how are we to obtain a direct pressure of the cramp on the largest surface, and which would have to be in one direction, end to end of the violin, seemingly a perfectly impracticable matter? The answer is, it is not practicable, hence the above numerous injunctions as to preliminaries, and which have to do with counterbalancing the impossibility of direct and strong pressure.

    The only pressure that can be applied directly is that of a nearly perpendicular one, the cramp grasping the button from underneath, with a proper guard or padding of millboard, or cork, cut into shape.

    A full brush of glue will now be passed over the whole of the surface of the socket, or receptacle for the root of the neck; which latter must an instant after be treated in the same manner. The two must be treated as one operation, and in a warm atmosphere. In the summer time no extra precautions will be necessary; but in cool weather the strong glue will soon set if the parts to be operated on are not kept in close proximity to a heating stove, or fireplace, or the apartment kept at summer heat.

    The neck and socket being thus kept at a warm temperature, the former will be firmly thrust into position, and with hand pressure put as close as possible. The superfluous glue will ooze out all around at the junction of the different parts; if it does not, that will be a sign that there is a looseness somewhere, or the surfaces have not been forced together close enough. This must be seen to at once, the parts separated and examined.

    It may be that the failure has happened through carelessness in allowing a chip to get in, or a piece of grit has prevented the opposing surfaces coming together. This being removed by a small knife, the brush, with a little more fresh glue, may be passed over the surfaces again, and the fitting this time should be perfect. The cramp and padding should be at once placed in position and screwed down tightly.

    All glue appearing above the joints should be carefully wiped away with a cloth kept ready to hand for the purpose; it is better to do that now than have to scrape or cut it away when hard; it will also save time.

    Ample time must be allowed for the glueing to thoroughly dry. This must be estimated according to the conditions of the time and place. In very warm weather, or where the atmosphere is heated artificially, the time consumed in the drying and hardening is less than when the air is saturated with moisture.

    When on examination the dryness is such as will warrant the removal of the cramp, this can be done. If all the measurements, fitting and precautions have been duly attended to, the neck or graft, with its line in the centre--supposing the present method is that adopted before the fingerboard is placed in position--will form an exact continuation of a line down the centre of the violin.

    A look down from end to end, or placing a long straight edged rule against the line, will be a way of testing this: if all is correct, the line will be perfectly straight and not bent. Should the latter be the case, the measurements, or fitting, in some respects, will have been inaccurate.

    It would be very provoking to find it so after all the trouble undertaken, and many instances are to be seen where the work has been left in this condition, and the stringing up and regulation has been, not only under great disadvantages, but absence of comfort in playing, and indeed the proper emission of the tone has been sacrificed.

    If the violin is one that is worthy of being performed upon with skill, there is only one alternative to putting it aside as useless, that of having the neck sawn off and the whole process of renewal gone through, with the aim of next time being more careful and true.

    Supposing, however, the neck is truly set and all is satisfactory, the next stage will be the laying of the fingerboard. This should be of good, close and straight grained ebony, free from knots. Fingerboards are usually sold in the rough; that is, with the upper surface, or rounded part trimmed down to an approximate curve. They are cut to lengths of about ten inches and a half to three quarters. Should the violin require a fingerboard less in length than this, a small portion must be sawn off, preferably from the small end.

    Great care must be exercised that it is done in right angles with a central line drawn from end to end. As the drawing of this line would entail some trouble, the under, or flat surface can be placed face to face with one that is known to be quite true, and a line with a fine pointed pencil made, or better, a scratch with the point of a small knife, guided by the true end of the perfect one. A fine toothed and sharp saw will remove the unnecessary wood. In doing so, precautions must be taken against splintering and spoiling the wood.

    To prevent this, a piece of waste wood, cut slightly out of the square, should be placed against the stop of the bench, so that when the ebony is placed against it, the sawing can be done flush with the side of the bench. The saw should be fine, in good condition, and gently used, or the line made will be ragged, ebony being brittle and splintering stuff, requiring some humouring in this respect.

    If the sawing is accomplished neatly and vertically true--this last is very essential--there will be little to do in trimming the surface of the end that is to come against the nut when near completion. A piece of fine glasspaper wrapped round a squared piece of pine, will make a good surface. The reduction of the width of the fingerboard at each end will then be proceeded with. In the case of an old neck being retained, the width of it at each end can be taken by compasses and marked on the flat side of the ebony.

    A thin shaving should be allowed for in finishing off. But we are on the work of a new neck; therefore the marking off should be done to some general standard. A good one may be reckoned as follows, for a violin of fourteen inches long and average width--total length of fingerboard, exclusive of nut, ten and a half inches--greatest width, one inch and five-eighths, width at nut, one-sixteenth under an inch. The ebony will be planed neatly down, with vertical sides, to these measurements.

    The height, or rise of the sides of the fingerboard above the maple, three-sixteenths of an inch, which may be kept for the whole length.

    The reducing to the requisite width and depth should be done with the plane in good order, a metal one for this kind of work being the best.

    The surfaces that are to be glued together must now be considered. An untidy looking black line along the neck at the junction of the ebony and maple goes far to spoil the general effect; a glance at this part will at once be sufficient for declaring whether the neck and fingerboard has been fitted by a neat and competent repairer. A frequent cause of the dark line--it is really a want of proper fitting together of the parts--is the hastily planing the two surfaces--straight enough possibly--and delay while the glueing operation is in progress.

    The fact of ebony being almost equally affected by moisture as other woods--in fact, more so than some--must not be lost sight of. Coupled with this curling of the wood under the influence of damp is the want of proper regulation of the pressure after glueing and placing the parts in opposition. An old-fashioned method of uniting these parts is still pursued by some repairers--the surfaces are planed evenly, the glue is applied over them, they are clapped together and string tied tightly as possible.

    Diagram 7 will show a modern and improved method, that of a mould of soft wood for back and front of neck and fingerboard. In affixing the fingerboard many repairers have left a gouged channel reaching from the nut to the end or insertion of the neck. This may be seen sometimes on turning the part towards the light.

    The intention seems to be from an economical view, that of removing the ebony, if necessary, without injuring the glued surfaces by pouring a little water down the passage and waiting till the damp enables the fingerboard to be pulled off without fracture.

    This tedious operation is wholly unnecessary, for the time spent would be worth more than a new one with its trimming up. Some repairers have used a toothed plane on the level surfaces to enable the glue to grip well. This is another mistaken idea. The fingerboard should not be treated as a permanent part of the structure never to come undone, it should be so secured as to last as long as required under fair usage, but in case of violence it is best that it should snap clear from the neck than hold tight enough to distribute, or concentrate, the strain on other and more delicate parts of the structure. Experience has suggested the following as generally best for all practicable purposes.

    The surfaces having been made true under the plane--this should be tested before the parts are glued, when, if true, there will be no line or the very faintest one seen. Along the middle of the ebony a very shallow gouged channel may be made, about half-an-inch wide and just deep enough to prevent the glue from touching when the fingerboard is placed in position. The level across over this channel from side to side can be tested by a metal straight edge or truly trimmed scraper.

    Occasionally from damp or the action of the plane the surfaces of both maple and ebony become slightly arched; in reducing this the scraper may be used with good effect, and a smaller one to take the least shaving more off near the channel, the even pressure when applied will close the outer edges more effectually.

    The glue to be used under present circumstances should not be strong, and if the atmospheric temperature is below sixty, or perhaps not down to that, the surfaces of fingerboard and neck should be warmed. When all is ready, see that the ebony is placed evenly in the centre and then proceed to apply the cramps in the manner before described (diagrams 33 and 34).

    The one placed over the button and the arch of the fingerboard in opposition to it must be sufficiently large, and the hollowed soft wood mould, or pad, should be more highly arched than the fingerboard, so that when pressed down, the outer edges, and not the centre of the latter, should receive the greatest pressure. The other cramps having been screwed down under the same conditions, the work can be placed aside to dry and harden.

    When a reasonable time has elapsed, according to atmospheric conditions, as in cold, damp weather, more time should be allowed, but under all circumstances the most dry and sufficiently warm locality should be chosen; the cramps may be removed, and of course the moulds too.

    [Illustration: DIAGRAM 33.]

    [Illustration: DIAGRAM 34.]

    We must now see to the working down of the graft or neck, not only to the requisite dimensions, but for the finish with some effort at style.

    By this last is meant such attention to evenness of contour from the button along to the edging of the shell, as shall be strong enough without looking heavy or clumsy; much of the nice appearance of this portion of the work depends upon the neatness of the workman.

    Assuming the button to be of the normal standard, or we may say, well calculated with regard to size for good effect--a good average width of this at the base where the curved line springs from the border is thirteen-sixteenths, and the projection forward--as it is not a geometrical curve--a half an inch. Some of the old Italian makers left the button very large, others small. The latter never pleases the eye of the connoisseur, who, accustomed to the proportion given it by the best masters (also the modern makers), thinks it looks poor and incomplete.

    As the neck or graft has hitherto been left but roughly hewn out, it will be projecting for some little distance beyond that which would be occupied by any button of average dimensions.

    Supposing the button to be too small, or injured, and an addition necessary, for the next move we shall require a pair of compasses; with these, after finding a centre of the segment of a circle formed by the outer edge of the button, with the other point find the distance inward, or the proper segment that is to be retained, bearing in mind that every possible part of the original button should be preserved; putting the point of the compass on the central spot as lightly as circumstances will allow, a thin scratched line must be made with the other point.

    Here we may remark that screw compasses should be used, so that distance apart of the feet may be kept rigid, as the width and the same circular scratch marked on the button must now be marked on a piece of maple, or, as is sometimes done, on ebony. The grain of either should run in the same direction as that of the button, or if done aslant it will look ugly when worn a little. The materials being matched, the fresh piece should be reduced in thickness to very little over that required for the height of the edging for the button; it should be a small cake of wood large enough to cover and leave a margin where it is to be fitted.

    The wood of the button outside of the scratched line will now be cut away down to the raw wood of the new graft; it must be done with small and sharp chisels, carefully paring it down, leaving the edge up to the scratched line quite perpendicular and smooth all round: the strictest attention to this is necessary, so that the fitting on of the fresh edging may be done with exactness.

    We now take up the little cake of ebony, or maple, as selected, with the scratched line, which should be made from a central point close to the edge as possible: if this is a difficulty, the centre may be taken further in, the circular line also and the superfluous wood cut away to the central point, but not in a way to interfere with the equipoise when the edging is placed on for fitting; if this is not seen to, the edging will, when finished, look awry.

    The middle within the scratched line may now be first gouged away and the wood cut with a sharp knife close up to and at exact right angles with the plane. A rounded file may with care be used to make a more even surface or run. If all this is done with precision, the parts may be tried together for testing--the glueing may be seen to and the cramping done, with care that the fresh portion does not slip during the process out of its place.

    Some repairers would be tempted to rely upon the exact fitting, and simply slide the parts together, squeezing them well, but this is always risky. The work may now be put aside to dry.

    The next proceeding will be that of working down or levelling both the ebony fingerboard and the graft, or neck. The first, in the state usually sold, will have an apparently well-finished off arching that may sometimes be near enough for letting alone after a little polishing down, but as a general rule it is not so, and further, if having been long "in stock," it may have settled down a little out of the straight during the seasoning process. Recourse should be had to the plane, a rather small metal one in good order with a keen edged iron.

    This must be closely regulated, or the surface worked upon will not be even but torn; hard woods, as before observed, require humouring and working down gently. The exact arching--in good work--of the ebony should be governed by a cut mould, one for each end. These may be made of some hard wood or metal, such as zinc, and if truly made will last any length of time. They should be trimmed to fit some fingerboard that has been ascertained to be just the thing in its arching.

    It may be as well to observe that some violinists prefer using a rather flatter fingerboard than others, but the medium is without doubt the best, and is not difficult to arrive at.

    The plane must be gently worked along from end to end of the fingerboard with as little pressure as possible,--hence the careful regulation and sharpness,--or you will find after a short time that instead of a nice even line, which must be tested from time to time by a straight edged rule, there will be a curved one, and this will necessitate further working down to the danger of losing thickness and sufficient strength in the ebony.

    If attention is paid to this, and a satisfactory even run of surface is obtained, glass-paper on a piece of straight, soft wood, but not of the finest degree, will be suitable for the present.

    We now return to the modelling of the neck from the lower part of the back of the scroll down to the button. This last, with its fresh edging or shield, will require another scratched line, making two semi-circular ones; it must be done from the same centre and calculated to allow of the wood being hewed away outside, leaving the full measurement when finished off.

    A chisel will now be brought into requisition for removing the useless wood outside the line last marked. The cushion or sandbag must be brought into use, the violin put face downwards, the fingerboard resting in a hollow. The neck or most convenient part for holding the whole with firmness must be held tightly, the chisel then worked downwards from the button, but not too far so as to cut into the portion that is to gradually enlarge, or form the quarter of a circle or the thickest part of the neck.

    We shall now use a strong coarse wood file and turn the instrument round and about, work away the neck until just outside of what will be left when the polishing down takes place.

    The curves should all be balanced well even while in the rough and the contour viewed from all points should be regular. The other end of the graft will require the same kind of attention, care being taken that too much wood is not removed.

    The level from each end must be seen to, leaving just sufficient wood to allow for fining down; the proportions must be well calculated, thus the upper end under the nut will be hewn down thinner than the part approaching the button, the line from each end being made quite even and the curving of the semi-circular shaft gradually tapering upwards.

    The glass-paper file before referred to will now come into service; it should be made of a nicely-squared plate of wood about six inches in length by about two and a half inches in width, with about one third of an inch in depth. We may call one side the front, the other the back; the edges of the former should be rounded down to a semi-circular form. All we have to do in making this useful file complete is to lap a piece of glasspaper of the degree of grain required round it, nearly meeting at what may be called the back for the time being.

    The surface with the rounded edging, or, as we have called it, the front, covered with rather strong grained paper, will be worked to make an even course all along the shaft, guarding all the while against working too much at one spot. The paper file may, after a sufficient working along the surface, be exchanged for one or two degrees finer, rubbing it in the same manner.

    For good mathematically even work, the graft should be turned round frequently, so that the light may throw up any little inaccuracies that may occur and which require individual attention. Here it may be remarked that if possible all repairing would be best done in an apartment that has as little reflected light as possible. The reason for this will soon be apparent when the fining down or polishing stage is commenced. One window, and that not too large, will be found advantageous.

    Little irregularities, however trifling, are best seen under such a light. Much rough work may very possibly be the consequence of badly-arranged light rather than inability or indifference of the workman. Repairs executed under unfavourable circumstances as above will often look very well until turned about in fresh and different lights, as they are sure to be, and then the faultiness becomes a surprise to the executant.

    The glasspaper filing must be continued for some time and with several finer degrees until the surface appears perfectly even and seemingly quite finished, but the stages are not yet complete.

    CHAPTER VII.

    FINISHING THE FINGERBOARD--FIXING THE NUT--SIZE AND POSITION OF

    GROOVES FOR THE STRINGS--FILING DOWN THE GRAFT--SMOOTHING, COLOURING,

    AND VARNISHING SAME.

    We now turn our attention to the finish of the fingerboard, which must have its sides attended to for appearing in good trim. For making a nicely worked surface each side, some preparations will have to be made.

    Firstly, the nut having been cut to the width, or nearly so, of the narrowest end of the fingerboard and glued into position, it will have to be filed down to the height at which it is to remain above the end.

    The arching will have to be higher in the centre than at each side, in order that when the strings are drawn over tightly, the thickest, or D string, shall have more room to swing than the thinnest, or E.

    The arching will thus be unequal, the lowest part being at E, next a rise sufficiently for the A, then a further rise for the D, and afterwards a drop again to a little higher than the A; this will be enough for the swing of the G. The grooves for each of these strings must follow in the same order. They will not be equi-distant in one sense, as that would cause them to appear unequal when the strain is on them.

    Probably the best way of securing a uniform appearance and the easiest, after one good result, is to cut a metal template with a spike at the central point or middle of where the string is to rest. These points will be found unequal when pricked on to the surface of the nut. A very small, round file should now be used carefully with the run of the fingerboard, or the strings when wound up will look as if pulled aside out of the straight line. The file must be placed exactly on the spot that has been pricked and worked backward and forward as indicated.

    The ruts must be examined frequently for ascertaining whether they are sufficiently deep. The height of each rut above the fingerboard cannot well be given in fractions of an inch, as they must be regulated to the convenience of the performer. A hard, rasping, orchestral player, with a heavy, unsympathetic bow arm, will require the ruts higher above the board than a soloist of refined taste. The relative heights, one with another, must be the same in both cases. When the ruts are finished, recourse must be had to the glasspaper file again to round the top surface of the nut with an inclination downwards toward the peg-box.

    This is an arrangement requiring care, as, when the nut is level with the fingerboard, there is danger of the strings jarring. When finished sufficiently even the ruts may require a little further attention, as it is difficult to at once complete them. The two parts are perhaps best worked one with another, neither being finished off in one working and left.

    We may now proceed to the further progress of the sides of the fingerboard; this, of course, can only be done when all is settled about the nut, this part requiring to be a continuation, notwithstanding the rise upward of the line from end to end. Preparation must be made for guarding the upper table of the violin from injury, from slips of the glasspaper file during the backward and forward movement. A good way to prevent this is to make a millboard or thick brown paper shield with a part cut away to allow the neck to have a hold.

    By putting this over the upper table and underneath the fingerboard a part will project forward on each side of the neck; it must be held in position by one hand, while the other holds the paper file, which will be worked along the sides of the fingerboard, at the same time being held nearly vertical. After some little time the part where the ebony joins the graft will appear worked down quite smooth, some finer degrees of the paper will reduce the surface to almost a polish.

    The nut receiving a part of the working will now present an appearance--as regards form only--of having been left from a reduction of the fingerboard stopping short at a straight line.

    This part now, if the fitting of the fingerboard to the graft has been neatly done, will show no line of glue or joint, but simply the difference of material. The upper edges of the ebony may be rounded down along to the end, but less at the lowest.

    The whole affair, however, is not yet complete, as the surface to be varnished must be made ready for it. If left in the present condition, players who are very fastidious would be complaining of the work not standing well or deteriorating under use. The cause of this deterioration will be that the moisture from the hand in using this part of the instrument in the raw state makes the grain swell as if wetted; this would occur to some extent even if fully varnished.

    This must therefore be anticipated by passing a soft, fully haired and wetted brush, or damp sponge, over the whole of the new work. When dry the whole surface will appear rough, or if of soft texture, somewhat corrugated; this must again be levelled down with some of the finest glasspaper, great care being taken that all the parts, and angles especially, are worked over.

    If the corners are not equally attended to with the rest--and to do this properly the angle of the steel scraper may be used with good effect--there will be a roughness at the part over which the varnish will settle, become rough when dry, and give the appearance of untidy corners.

    If the scraper with right angles is insufficient to clear the corner satisfactorily, one with a rather acute angle will be found to do the work; it must be sharp, and gently used (or ridges small, large, or both, will become evident), working across first one way then the other until the appearance is quite up to the exactions and desire of the eye.

    Another wetting will be of some further benefit for a good and lasting surface. When dry the roughness will not be so obtrusive as in the first instance, and the application of the finest grain of glasspaper, or a piece that has been under use for some time and got a little stale will give the desired surface. The action of the glasspaper over the surface should be continued for some time, until there being less and less powder routed up the surface, it assumes a polished appearance, and if the whole work is well done it will suggest a kind of finish that looks too good to spoil by covering up with varnish.

    But the latter is a necessity; if not really varnish in the usual sense of the term, a substitute must be used, and here we touch a little upon the confines of fashion or individual fancy.

    It may not be generally known that the old Italian makers--I mention these as they have always been looked up to as guides for almost everything in connection with violin facture--varnished the whole of the neck--which under present circumstances we call the graft--with the same varnish and thickness of it as the rest of the instrument.

    We never see such a thing now, and if a maker were to send forth his new violins in this manner or trim, he would be looked upon as eccentric.

    Nevertheless at one time it was universal. Probably the increased number of movements of the hand, and especially the thumb, to meet the requirements of more florid execution and in connection with the growth of the ability among players for performing much music on the higher positions or shifts, showed very soon how the coloured varnish looked patchy under wear. This fashion of covering over the most handled part of the instrument with the coloured varnish then became discarded.

    "Appearances must be preserved" was found to be an axiom almost forced upon the makers and repairers, and, as time went on, the substitution of strongly curled wood for necks or grafts, in place of the plainer material hitherto used, gradually settled down into the present fashion. Now-a-days the skill of the repairer is exercised in the various treatment of this part.

    Players vary in their tastes or whims, some liking a perfectly smooth or polished surface as more suitable to their handling than what they understand as an unvarnished neck, others like it the other way as not so likely to slip, there being a little more hold or resistance. Anyhow, the raw wood cannot be left simply glass-papered, this would be speedily followed in use by an accumulation of dirt and grease unpleasant to the eye, and to the touch, clammy and unwholesome. It will therefore be as well to consider the two modes of treatment.

    In either case the parts of the graft near the insertion in the socket and at the other end where the peg-box is fitted will require varnishing down.

    Before active operations commence a fair examination should be made of the colour or complexion of the body of the violin. Very often this has no attention paid to it, with the result of a hideous contrast between the neck and the ribs adjoining, a sign of bad workmanship and carelessness. The materials at hand for making a good match must then be thought over, the most appropriate selected and the number of coats, if possible, determined upon.

    This latter will be taken in a general sense, as an exact number will not be possible; appearances are in this process deceptive and must be regulated by the exigencies of the moment, but what can be calculated is the question of one or two applications only (which would result in a cheap and common appearance) or a number with the same materials carefully laid to the satisfaction of the repairer.

    Without plunging into the whirlpool of the best or particular gums, resins and their individual mode of application, a matter that will take up hereafter our more undivided attention, it may be taken as a certainty that the varnishing materials used for the parts under consideration must be of an alcoholic solution, no other would "set," evaporate or dry with sufficient rapidity to allow of handling: or, as we may put it in another way, that would lose tackiness within a convenient time.

    Most people are aware of the nature of an oil varnish during the drying process, there is firstly the "setting," that is, all the volatile particles dispersing; secondly, the real drying or hardening which ensues with sufficient time or age; both accompanied with some degree of contraction, and until the process is complete, handling or friction of any kind has to be carefully avoided. This will at once show its unsuitableness for repairs and restorations, especially of the kind now under consideration.

    The same process has to be gone through in the drying of a spiritous or alcoholic varnish, but it is so much the more rapid in consequence of there being only the alcohol to disperse, leaving the resin in a comparatively dry state.

    Colouring will be the chief consideration after the resin has been selected, and on this the judgment of the operator will have to be centred. For obtaining the effect desired or that is fashionable at the present day, one or two coats or paintings will be commenced at the corners where the graft is inserted in the upper ribs and gradually being thinned off as the curved part rounding upwards from the button dies away.

    Sometimes in consequence of the fresh wood appearing very white--it is not always possible to obtain aged wood--some colouring material or stain mixed with the first two wettings will subdue the staring aspect, this may be continued along the graft and bring up the figure or curl more prominently. Often between the curves each end of the graft repairers force very strong stain, this being sometimes common writing ink; when varnished over the effect is violent and common even when nicely done.

    The best that can be recommended is some sufficiently dark wood stain--sold at most of the oil and colourmen's shops--and rub it in, allowing it to dry and then finishing off as before described.

    If the neck is to be left unvarnished, as it is termed, the colouring and fining off can be followed with a rubbing of good oil, linseed, raw or boiled, it must be really rubbed in and vigorously frictioned up and down with a dry cloth--or after an application of the same kind with some old fine flannel. This will drive in the oil, consolidating the whole, and as it will dry inside after a time, keep a good smooth surface under usage.

    Some repairers continue to varnish or polish along the sides of the fingerboard to the extremity. There is no objection to this, and if very neatly done, the general effect is enhanced. The varnishing of the whole of the fingerboard is perhaps not so good in general, too much glare seeming to obtrude itself, but the filling up the pores with the varnish and then working it down to a dull surface has a good effect and helps in the resistance to wear.

    The polishing of the neck, or fingerboard with it, may be effected by making a small ball or dabber of about half an inch in diameter of fine grained flannel; this should be covered with another surface of closer material such as calico, but large enough to enclose the little bunch and to be tied up with a piece of string.

    A portion of varnish being placed ready in a smaller saucer or any convenient porcelain article with a shallow even bottom, the ball or dabber will be moistened with some linseed oil and then its rounded face dipped in the varnish and rubbed briskly, but lightly, over the surfaces to be polished. These surfaces rapidly absorb the polish, while the oil in the dabber allows it to pass over without clinging.

    The rubbing should be continued until a smooth, glassy appearance comes and you feel sure that the wood has imbibed enough of the polish; this treatment may be continued over all the parts at which it may be desirable to have an even shining surface. The work may now be put aside for some hours, so that the evaporating and hardening may take place.

    When this has been ascertained to be satisfactory, the surfaces may be wiped gently with some soft, absorbent material which will take away any superfluous particles of oil that may have been accidentally left in the process of rubbing.

    If there should be some uneven, clotted, or rough parts observable, a small ball or dabber made in the same way as the preceding, but used with spirit and oil instead of varnish, will work these down to a proper condition. For the dead surfacing, care must be taken that all is quite hard enough. Taking a small piece of flannel of fine texture doubled up and with its face well oiled, having some rotten-stone powder at hand, dip in the latter and rub as before lightly round and round over the parts to be dead polished; this will give a nice refined, even appearance, with comparatively little glare. A final wipe off with a soft cloth as before, will bring matters to a conclusion.

    CHAPTER VIII.

    INJURIES THAT CAN BE REPAIRED FROM THE OUTSIDE--INSERTION OF FRESH WOOD

    IN FRACTURE OF THE RIBS--THE EFFECTS OF CLIMATE ON THE GLUE IN VIOLINS.

    We may now take this portion of the work as finished and turn to the consideration of repairs of fractures or filling up of parts last. It is early yet to think of opening the instrument for the purpose of rectification of anything that appears to have gone wrong either with the general structure or with small details. A golden rule to be observed by all repairers is that of never opening an instrument--that is removing the upper or lower table--until all other means of correction have proved futile.

    Extensive repairs to the interior may be accomplished without opening after a very careful look over with proper calculation.

    There are several reasons for keeping the above rule well in mind, among them, that if the violin is old and has undergone much affliction while under the hands of many doctors, some of these possibly belonging to the "heroic school," it may be found that the last visitant of the interior had straightened, bent, or contracted and held some of the parts together while the glue was in process of drying and that sufficient time had not elapsed since the occurrence for the strained parts to settle down under their new condition.

    An opening of the violin, removal of upper or lower table or any large portion, must be undertaken after due consideration and every precaution has been taken that nothing shall be disturbed if the reparation can be accomplished without. An opening of the instrument for the purpose of one repair may lead to the necessity of half a dozen before closing up again.

    Our opening ceremony will therefore be postponed until a future occasion, and we will confine ourselves to the consideration of such external injuries of ancient or recent origin that may be with the least inconvenience restored to ordinary health or even strength. The numbers of such and their varieties are more than can be related, the curious manner of their occurrence, too, would be an addition that would indefinitely prolong the story.

    Taking, therefore, small injuries or fractures that can be repaired from the outside, among the first coming to mind and not infrequently seen, is at the corners, a small piece of the projecting part of the rib--one of the upper or lower sets; this may have caught against something and got lifted away from the block, it may be on one side or the other, in size perhaps little more than an eighth of an inch, but all the same requiring immediate attention, or dirt will get in and make an adjourned repair more difficult if not wholly impossible to obscure.

    According to the condition, age and date of the injury, so the treatment must be. If the injury is quite recent and the fractures are quite clean, some good thick glue placed on the exposed surface and the lifted piece placed back in position may remain there with no further attention than the wiping off when dry of any superfluous glue that may have exuded when pressing the part on. This has been a simple matter, but if the part knocked away is lost, a different course must be pursued.

    As it would be impossible to find a piece of fresh wood to fit a ragged or irregular-shaped hollow, there is but one method to proceed upon, that of clearing a regular space with a sharp pointed knife. The walls of the space or opening should be as clean in line as possible, also quite vertical. A small keen-edged chisel may be found advantageous, as, by its aid, using it with the angular or sharpened side downwards, the floor of the excavation can be reduced to a fair level.

    This hollowing-out should not be too deep, leaving as much as possible of the bare wood uncut, only enough being removed for a good holding surface. If this is done neatly, the opening will be like that of a box into which will be fitted the fresh wood. As to this last it should be selected to match both with regard to texture and age whenever possible, also in continuation of the run of the grain, so that when fitted it should look as much like the surrounding wood as possible, that is, when free of varnish.

    In cutting the wood to the required size it should not, as in the instance of the aperture, be made with perfectly upright sides, but the parts that are to go into the aperture should be a fraction less than the outer, so as to allow of its being pressed in and fitting very closely all round.

    As the parts under consideration lie in the curved parts on the structure, to fit a piece in with success, it should also be bent with a requisite curve; if this is not attended to, and the clear varnish comes over it when being finished off, there will be a glistening of the grain underneath when shifted about in the light. To avoid this, which is apt to draw attention to the repaired parts, a larger piece of veneer than necessary should be first bent into the proper curve and the part nearly small enough cut from it and then made to fit.

    The bending of the piece can be effected by steeping it in some hot water, pressing it into form; being but a small portion, it will probably retain its inclination; if large enough and obstinate it must be kept bent by some means until dry, when it will show no disposition to revert back to its old form.

    If these particulars are all attended to with care, the piece of wood or veneer will only require a little pressure--the opening being gone over with strong glue--to retain its form in proper position. In case of failure under these conditions and the parts not holding together as they should, another course must be adopted.

    It will be most likely that some grease is the cause of the non-adherence of the parts. The remedy will be that of using a little benzine on a brush and wiping or mopping out with a small piece of linen on the end of a pointed stick of soft wood, after which, when quite dry, some fresh glue must be applied, and the parts pressed together and held in position.

    Ingenuity and the perception of the adaptation of means to an end will constantly be called into exercise, and at a part of the instrument such as is at present under consideration, will be often severely taxed.

    Want of purchase or no direct pressure being possible, or at least perceptible, will be the complaint of the operator, but this can always be overcome with a little patience.

    Now supposing that a piece has come off at the upper part of the waist curve, and if narrow or the curve is sudden it will at first sight be a little puzzling as to keeping pressure on the fresh part, even if cut sharply and ready to be deftly inserted.

    The difficulties will be considerably lessened, if not disposed of, if we take up a portion of soft pine or poplar, cut it in a moment or two to shape, so as to very loosely fit the upper curve or part we are about to glue, and not quite reaching the lower or usually larger curve of the waist; a small piece of cork placed between the wood to be inserted and that which is to press it while in position and another piece of cork of a wedge form can be squeezed in at the other end, so as to prevent the varnish being injured and to tighten the pressure, which will not be necessarily great if the fitting is good.

    Another kind of repair not unfrequently necessary, and which should not be delayed, is caused by the parting of the two ribs at the angle, in consequence often of accidental knocks and over weak glue. This is a more difficult part at which to get direct pressure than almost any part of the instrument. Many repairers would lift up the loose part or parts, both being occasionally loose, brush a little glue in, squeeze the parts together and leave them.

    When dry the ends will under this treatment seldom be found to meet properly as in their original condition. The best mode of repairing will be found that of proceeding by degrees, overcoming the enemy in detail.

    Thus firstly, we must observe whether the junction or construction of this part has been effected in the old Brescian manner--that is, the two equal parts being brought together, or according to the later method, the end of the middle rib being placed in position first, trimmed to a feather edge and the upper left thick and slightly overlapping it and afterwards trimmed into shape.

    In both instances the under surfaces must be cleaned and all the hard old glue softened and cleared out, if unfractured the surfaces of both corner block and rib fitting will be as originally left by the maker. In either style of construction it will be best to proceed first with the middle rib and support or prop it against the block in the way before mentioned. When quite dry we can remove the pressure and get to work at the other.

    After being quite sure that no hard glue or foreign particles remain between the surfaces to prevent a perfect fit as in the original condition, a small mould cut from soft wood again and of a size and shape that will fit loosely the semi-circular part must be cut, and some soft paper got ready to go between as a protection for the varnished part.

    If the parts are not much worn away, or the front and back plates are in fair condition, the rib may be glued and the screw cramp, cork or paper of course being used as a protector, and the rib will be held in position. If this is not sufficient for getting a close and accurate fit, the soft wood mould mentioned above must be placed, and a slight pressure gained by a wedge of wood gently inserted and pressed home. This mode of repair, it will be borne in mind, is when the upper and lower plates are in fairly good condition.

    Different treatment would be adopted if both were separated or the upper one taken off.

    Sometimes the cramping, although sufficient for getting a good mend where there is a good extent of surface, will not be quite the thing for a small part, perhaps a slight opening at the extreme edge; in this instance a wooden mould, cut in a few minutes from a flat board large enough to allow of an oval aperture being made that will admit of the body of the violin being passed through. This being done and a small wedge being here and there judiciously inserted, will enable the operator to get enough purchase, or advantage may be taken of the juxtaposition of the cramp, and using both to gain the requisite pressure against the bend of the rib in the manner before mentioned.

    There are as a matter of course extremely numerous kinds of fractures or injuries arising from almost as many different causes. If time and space permitted, they might be classified and each credited to their different agencies. Sufficient for our purpose, however, will be the separation of them into three divisions: firstly, those which may be the outcome or result of ordinary wear and giving way of parts through atmospheric influence, such as damp or excessive dryness, or both at times, in combination with varying temperature.

    People are apt to debit the climate of Britain with many shortcomings and the cause of much undoing of good work in the fiddle world and the prevention of its being accomplished in the concluding stages of fiddle facture.

    Much of the good quality attached to Italian instruments has been attributed to the beautiful and dry air of Italy. Now that Italy has beautiful air no one can deny, that is, while not standing in the streets of some of the most interesting cities therein, but that it is dry generally is perhaps going beyond the mark; remember it is a very mountainous place with some exceptional portions, this may be easily verified by a glance over a good map of the place, or better, a tour by railway from the northern provinces down as far as Naples.

    Knowledge is fairly general as to mountainous districts, much more than plains, being the localities where rain is most frequent, the more or less saturation of the atmosphere following as a matter of course.

    But let Italian fiddles speak for themselves, otherwise than through the medium of gut strings. The first makers of violins in Brescia used no side linings, but trusted to the most excellent quality of their glue for holding back and front to the ribs. That their trust was not misplaced in many instances is proved by the work in its primitive condition remaining intact to the present day.

    With the rise of the Cremonese school, delicacy in treatment of detail became fashionable; makers found that in order to give expression to their ideas in as many particulars as possible over the work, especially in respect of refinement in the curving of the ribs, less thickness of wood in these parts would have to be used, especially when of very decided curl; but this would not hold well except in the driest districts.

    The system was then introduced of using the thin slips of wood running from block to block; the thickness of these, although slight, added to the thin substance of the rib, allowed a better holding power to back and front.

    The fact is here evident that the glue, of exceeding good quality--and that it was so will be corroborated by all repairers who have had to do with the old Italian instruments--was too easily affected by the damp of the atmosphere.

    Further evidence frequently turns up among the great numbers of old Italian instruments gathered from all sorts of places, of the efforts at combating the effects of damp. Some of the means adopted by various repairers, apparently in the smaller towns--judging by the bad, even extraordinary woods used--have been very curious, many interesting, others primitive, even stupid. At about the same time the Amatis were introducing the use of side-linings, Giov.

    Maggini was trying other means of preventing the parting of the upper and lower tables from the ribs by damp. A method he adopted, and which many later makers imitated--if it did not occur to them spontaneously--was by cutting a groove all round and inserting the ribs. It will be obvious from this that no linings were used in these instances. That his efforts were not followed by success may be concluded from the fact that he did not persevere with the system. The simple method of his master was fallen back upon and thicker ribs placed in position.

    When we come across one of those grooved tables it will probably be found--as might have been anticipated by Maggini had he known beforehand of the course to be taken by his art, which was at the time almost a local one--that a repairer has at one time thought it necessary to lift the ribs from one or the other plate, and almost, of course, bungled over it. This will be seen in the irregularity of the fitting of the ribs, which have been ruthlessly cut or torn out of the groove, some portions being left in.

    Taking them out was found to be unprofitable work, with a general result of a wretched wreck remaining, instead of the whole original being there but shifted a little, from the glue losing its hold while perishing from the action of moisture.

    CHAPTER IX.

    THE GLUE USED BY THE EARLY ITALIAN MAKERS--INSERTION OF PIECES OF WOOD

    FOR REPAIRING LOST PARTS--REPLACING LOST RIB AND REPAIRING INTERIOR

    WITHOUT OPENING WHEN POSSIBLE--SECURING LOOSE LOWER RIB TO END

    BLOCK--DIFFERENT METHODS--TREATMENT OF WORM-HOLES--FIXING ON GRAFT ON

    NECK.

    Here, before proceeding further, it may be as well to call attention to the kind of damage done by the atmosphere. We speak of the glue perishing. Under most circumstances this will not occur, but under exceptional ones it will. If good in the first instance, it will be perfectly sound and strong as ever at the end of three hundred years.

    I have found this to be so in the work of Gasparo da Salo and his pupil, Giovanni Paolo Maggini, besides other makers nearly contemporary. What particular kind of glue they used I am unable to say, possibly they did not know very much more themselves beyond what they believed was the best obtainable in their day and city. When the perishing has occurred there must have been very much moisture in the atmosphere of the locality in which the violin rested for some time, as the best glue will absorb the most moisture before losing its firmness, or power of adherence.

    Prolonged exposure to damp allows chemical change to take place and then all adhesive quality is lost; when dry air afterwards attacks it, the parts of the instrument that should have been held firmly together are released, with results that may be serious in degree according to the position of the part affected.

    To continue the consideration of the repair of a violin that has been constructed with grooves for holding the ribs.

    A long and troublesome piece of work would be the loosening and taking away of the fragments of rib inserted in the groove and cut away by some repairer from the rest or standing rib; it is therefore preferable in ordinary and neat repairing to clear the parts that may be ragged or begrimed, firstly, by washing with a stiff brush of appropriate size and wiping with a clean cotton rag repeatedly; when the rag ceases to be soiled or discoloured after wiping, the parts may be taken as fairly clean.

    A sharp knife will take off any projections that may be prominent and prevent the proper placing of the rib in position; if the irregularities give indication of fitting well, the parts may have at their approaching edges a touching with strong, hot glue, and the cramps with protection applied as before for other joinings.

    The probabilities, however, are, that through bad treatment, added to wear and tear, the parts will not fit under any circumstances, then the only course will be to make an even surface at the part broken away, and then fit a piece of fresh wood therein. If the aperture made is not of large extent and not wide, or more than the thickness of an average piece of veneer is required, then the fresh wood need not be bent, but cut neatly for fitting, and after glueing, as usual, slipped in with a part projecting beyond the surrounding surface.

    When quite dry it may be pared down carefully with a sharp knife, or if not manageable on the curve of the rib, a chisel of size according to the amount of room; being a narrow slip, after the colouring down and varnishing has taken place, it will be but slightly noticeable. The same treatment can, of course, be adopted for either upper or lower part of the rib; the middle rib position will give the most trouble, owing to its concavity, but care and patience will overcome the difficulties of the situation.

    Should there have happened an accident by which a hole of some extent is rent in the ribs--either upper, lower, or middle--it is not absolutely necessary that the instrument be opened to accomplish the repair; bear in mind the advice given before, not to open a violin which has been in good going order if the repair can be effected without.

    As we are presumably working on disabled violins that are valuable, perhaps old friends, or interesting specimens of a particular school, to select the best mode of restoration is our aim. For this purpose we will call to our aid some low class violin, new or old, that is of no value except for our purpose. If several are within reach we can select one with wood that matches as near as possible the one under process of restoration.

    Being already bent to shape, a portion may be found somewhere about it, that with a little exercise of judgment can be cut out to shape, and as in manner pointed out before, be placed over the aperture of the fracture. Care must be taken that it quite covers the part, while being likely to fit sufficiently well as regards figure or curl and direction of grain.

    The sides cleanly cut should not be quite vertical with the general plane, the inner surface being a shade smaller than the outer, thus enabling the operator, with a little pressure, to insert it, when glued, quite neatly. No instructions or suggestions with regard to fitting will counterbalance clumsiness of handling. In operations of this kind, delicacy of handling equal to anything required in watch repairing will be obligatory, that is if restoration of a high class is intended.

    It would be impossible to deal with, touch upon, or even to recount every possible injury to a violin that might be repaired without the removal of the upper table, but there are still some remaining that will be worth considering, if only for the purpose of restraining the tendency to open the instrument upon too trivial a pretext. One instance occurs to memory at the present moment, in which a violin, the constant companion and closest friend of its owner, met with an accident that seemed to him well-nigh total destruction, at any rate, necessitating much renewal with undoing and plastering up of fractures.

    To the fiddle physician it was promptly taken, carefully scanned, and the owner told that it would be all right in a few days. Will it have to be taken all to pieces? asked the anxious owner. Not if it can be possibly helped, was the reply. The violin was called for in due time, and in answer to inquiries it was fetched and seen to be in as good going order as before the time of the accident. There was no apparent evidence of damage, no sign of fracture or any neatly-laid patches, there were the ribs as sound as when new, no cracks to be seen.

    How did you manage that? said the owner, and you say there was no necessity to take the front off? Easier far, replied the repairer, the more there is left undisturbed the more assistance will these parts give you during the progress of restoration, and as you seem curious and desirous of solving the mystery of this renovation I will relate how it was accomplished.

    You are no doubt fully aware that your violin is of a size and shape well-known in the trade as a "Strad pattern;" well, there are thousands of violins in any number of degrees of quality similar in form and size, in fact, for us modern makers there are too many about. Catching the peculiarities of pattern with my eye at a glance, the difficulties to be overcome were not very numerous or great.

    I saw there was no reunion of parts of the ribs to be thought of, as they had gone, and your violin being a modern copy of ordinary pretensions, it would not serve our purpose to join four-fifths of new rib to the remainder, and so to make a clean and satisfactory renovation a fresh rib would best answer. Taking down from a shelf a number of loose parts of violins put aside for such occasions as the present, I soon found a middle rib that matched in most particulars those of your violin. It had the additional advantage of being better for the keeping, as regards colour or looking less new.

    The first proceeding was to clear out all the useless fragments of the spoiled rib, search every corner and see that there were no splinters left, and remove projecting particles of glue. All edges that were to come in contact with the fresh rib were washed, and where permissible, the surfaces made even by a slight levelling, finely shaving them with a sharp tool.

    The fresh rib was then tried, and being of full size and requiring more than the least pressure to get it placed, some little shaving down here and there was found necessary, and when done it was tried again carefully and repeated perhaps three or four times, when all parts seemed to fit sufficiently well. Each time the rib was inserted there was, of course, nothing projecting whereby it might be withdrawn; to accomplish this, a bent wire of sufficient strength passed through the most distant of the two sound holes gave it a push out again.

    When the piece was found to fit with accuracy, little remained to do beyond glueing the edges that were to come together, and after seeing that every part was in right position, the screw cramps were applied with sufficient force and no more, the superfluous glue wiped away and the whole left to itself.

    When sufficient time had been allowed for drying, the cramps were removed, a little cleaning of parts effected and the fresh work varnished in a manner so as to match nearly as possible with the rest of the instrument, and there you have your violin with a fresh rib inserted without removing anything but the damaged part. It was really, as you may have perceived, the easiest way of working the thing, there being no secondary process to be gone through, nothing but cramping down, varnishing and finishing off.

    Another instance comes to my mind of what can be done in the way of alteration of the interior without removing the upper table. It came within my own experience many years back, and the violin was one owned by myself at the time. It had got into a condition not unfrequently seen after bad repairing, that of the fingerboard sinking down too near the table through absence of proper support or sufficient grip of the end of the table where the neck is inserted.

    Being unable to attend to the matter myself at the time, I sought the aid of a friend living close by, a clever amateur violin maker and mechanical constructor of other things beside. He was not very long setting matters right, and my violin seemed in no danger of further getting into disorder from the same cause. I asked him how he had managed the rectification of the matter; did he take the upper table off? "Oh no, without that.

    I simply opened or loosened the left side of the table about and above the upper corner, then, having cut and glued a slight thin wedge-shaped piece of wood, through the narrow opening caused by the loosening of the table, I passed it on a thin knife long enough to reach to the upper block, between which and the part of the upper table which was not holding I carefully thrust it and tucked it in, finally glueing and cramping again the part of the table that I had purposely loosened."

    This was a clever operation, successful but very risky, and not to be lightly undertaken by anyone without much experience and even natural ability for mechanical adaptation of means to an end. There was much danger, from the narrowness of the approach to the work from the side opening, of missing the mark and dropping the piece of wood with great difficulty of recovery, and, further, the chance of cracking the upper table by straining the opening for the admission of knife and wedge of wood. I heard of the violin but a few days since, and have no reason to suppose there has been occasion to have any further repairs done.

    Among other mishaps occurring at times, and which from their position seem difficult to remedy, is that of the lower rib becoming detached, or losing its hold on the block; this is more liable to take place when there is a join running up and past the tail pin hole. Both sides may be loose or one only. When, as in a great many of the old Italian violins, the rib is continuous, it very seldom gets detached. Here the advantage of simplicity of construction is made evident.

    The rib being of one piece running round the lower end right past the tail pin was not, as too often supposed, done for a saving of time by one operation, but for strength and neatness. When in two parts, sometimes with a piece of purfling inserted--each side is subject to damage either by the tampering with the tail pin, the nut above, or during repeated removals of the upper table. Exposure to damp will, as a matter of course, affect the original glueing of these parts as soon as any other.

    The detachment from the block may remain unnoticed for some length of time, until getting worse by degrees one part may be seen to be lifted or warped away from the join. If without this appearance suspicion is aroused in some way as to looseness, it can be verified or not with little trouble by tapping with a felt-headed piano-hammer, when the sound, which should be quite solid, will, on the contrary, be rattling.

    Seemingly the repair of this part is an awkward matter from the absence of any purchase for pressing the parts and retaining them in position when freshly glued. The difficulty is more apparent than real, as there are several ways of overcoming this obstacle. To begin with one. The tail pin will, of course, be removed; if fitting rather tightly and of good length, use may be made of it.

    As usual all the parts to be glued must be cleansed by a brush and clean water, sopping up the moisture after each application, pressing repeatedly the loose parts until they seem to be clean enough. A piece of soft pine or poplar will now be cut that will be just wide enough to go easily over the parts lying over the block and which of course cover all the loose parts that require fixing: it may be a trifle under a quarter of an inch in thickness.

    One side must be shaped to fit the parts over the block when pressed against them and should be a sort of mould. A hole will now be pierced to admit the cylindrical part of the tail pin, or if not long enough, a made substitute with a similar rim. It should be tried by passing it through to the tail pin hole, and if it fits tight enough to sustain itself against some pulling we can proceed.

    The fit should be close enough so that when the peg is passed through the hole in the mould and the latter pressed by this means against the rib or the two parts on to the block, all should be held firmly in position. Taking them apart again, strong glue should be applied by a brush to the surfaces that will meet or be worked in as when the cleansing was going on. The peg and the mould--with a piece of paper on its face to prevent adhesion--may then be pressed in to hold tight until hard and dry.

    The same method may be pursued with the exception that in place of the peg a screw--if one is to hand large enough--may be inserted. In this case it should be a very loose fit to the hole, the grip will be obtained by rolling up a piece of paper and inserting it in the tail pin hole, the screw can then be used against this inside without damaging the block.

    Another way of accomplishing the desired result will be by a stout leather strap and buckle passed round over all the ribs of the instrument; the same sort of mould will be used and applied in the same manner. The strap will need holding in position at the upper or neck end over the button, a string over the fingerboard will be sufficient; at the other end over the mould a wedge of soft wood according to size will enable the pressure towards the block to be regulated.

    Another contrivance with the same mould, for this must always be used, is by getting a wire with a turned or screwed end fitted with a head or nut, the other end can be bent to right angles, but not too much length used or it will not go through the tail pin hole.

    When in position, having been passed through the hole in the mould, the right angled or bent end will catch against the inner surface of the block, the head or nut being then screwed round will tighten and press the mould towards the block with enough grip for the purpose if all the rest is in proper order.

    Should these contrivances not be to hand or are found inconvenient, yet another method is that of using the screw-cramp. A portion of mill-board or cork being placed to protect the parts of the upper and lower table between which the end block is situated, the screw can be turned tight enough to allow of a wedge of wood being inserted between the back of the cramp and the mould without risk of shifting; it can then be left until dry and hard.

    Occasionally there will be not only the detachment from the block, but there will be the accompaniment of a split in the rib. There will be in this instance a preliminary cleansing of the split and joining together before proceeding with the other part. The reason for doing this is that the pressure on towards the block is apt to widen instead of closing the crack. The most usual way of mending a crack, or there may be more than one, is by the use of a small hand vice.

    A piece of stout card placed between the teeth of the vice to prevent an imprint, the part to be joined will, after cleaning and glueing, be brought closely as possible together and the vice screwed up. For this process the help of another person will be almost absolutely necessary, as two hands will be required for holding the parts together while the second person holds the vice and turns the screw to order.

    When dry and unscrewed the parts joined will require a little scraping of the superfluous glue, washing away at a thin part as this is would be dangerous; if brought together neatly the rib can then be pressed on the block in the manner before explained.

    The same process will be gone through when a portion of fresh rib has to be inserted at this part, owing to loss of a piece through violence or the ravages of the worm. In the latter case searching inquiry should be made with a pointed wire or pin and the direction of the boring operations ascertained, as it may be necessary to insert a larger piece than was originally intended to avoid a large smash or general collapse at the part where the greatest strength should be. There is often too great a tendency shown in repairing, especially in preparation for the market, as, for ins

    Edition notice Project Gutenberg source, credits & licence

    The reading text above is the public-domain work. The Project Gutenberg header, production credits and licence are kept here as provenance rather than shown before the book.

    Title
    The Repairing & Restoration of Violins
    Author
    Horace Petherick
    Release date
    October 11, 2008 [eBook #26878]
    Language
    English
    Credits
    Produced by Ron Swanson
    Transcriber and production notes
    Produced by Ron Swanson
    Front matter as received (title page, contents)
    THE REPAIRING & RESTORATION OF VIOLINS.
    
    
    
    
    PRINTED BY E. SHORE & CO.,
    3, GREEN TERRACE, ROSEBERY AVENUE, LONDON, E.C.
    
    
    
    
    [Frontispiece: HORACE PETHERICK.]
    
    
    
    
    _"THE STRAD" LIBRARY, No. XII._
    THE REPAIRING & RESTORATION OF VIOLINS.
    
    
    BY
    HORACE PETHERICK.
    
    _Of the Music Jury, International Inventions Exhibition South
    Kensington, 1885; International Exhibition Edinburgh, 1890; Expert in
    Law Courts, 1891; Vice-President of the Cremona Society_.
    
    
    ILLUSTRATED BY THE AUTHOR.
    
    
    
    
    London:
    THE STRAD OFFICE, 3, GREEN TERRACE, ROSEBERY AVENUE, E.C.
    D. R. DUNCAN, 186, FLEET STREET, E.C.
    
    New York:
    Header as received
    The Project Gutenberg eBook of The Repairing & Restoration of Violins
        
    This eBook is for the use of anyone anywhere in the United States and
    most other parts of the world at no cost and with almost no restrictions
    whatsoever. You may copy it, give it away or re-use it under the terms
    of the Project Gutenberg License included with this eBook or online
    at www.gutenberg.org. If you are not located in the United States,
    you will have to check the laws of the country where you are located
    before using this eBook.
    
    Title: The Repairing & Restoration of Violins
    
    Author: Horace Petherick
    
    
            
    Release date: October 11, 2008 [eBook #26878]
    
    Language: English
    
    Other information and formats: www.gutenberg.org/ebooks/26878
    
    Credits: Produced by Ron Swanson
    Full Project Gutenberg licence
        
    
    Updated editions will replace the previous one—the old editions will
    be renamed.
    
    Creating the works from print editions not protected by U.S. copyright
    law means that no one owns a United States copyright in these works,
    so the Foundation (and you!) can copy and distribute it in the United
    States without permission and without paying copyright
    royalties. Special rules, set forth in the General Terms of Use part
    of this license, apply to copying and distributing Project
    Gutenberg™ electronic works to protect the PROJECT GUTENBERG™
    concept and trademark. Project Gutenberg is a registered trademark,
    and may not be used if you charge for an eBook, except by following
    the terms of the trademark license, including paying royalties for use
    of the Project Gutenberg trademark. If you do not charge anything for
    copies of this eBook, complying with the trademark license is very
    easy. You may use this eBook for nearly any purpose such as creation
    of derivative works, reports, performances and research. Project
    Gutenberg eBooks may be modified and printed and given away—you may
    do practically ANYTHING in the United States with eBooks not protected
    by U.S. copyright law. Redistribution is subject to the trademark
    license, especially commercial redistribution.
    
    
    START: FULL LICENSE
    
    THE FULL PROJECT GUTENBERG™ LICENSE
    
    PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK
    
    To protect the Project Gutenberg™ mission of promoting the free
    distribution of electronic works, by using or distributing this work
    (or any other work associated in any way with the phrase “Project
    Gutenberg”), you agree to comply with all the terms of the Full
    Project Gutenberg License available with this file or online at
    www.gutenberg.org/license.
    
    Section 1. General Terms of Use and Redistributing Project Gutenberg
    electronic works
    
    1.A. By reading or using any part of this Project Gutenberg
    electronic work, you indicate that you have read, understand, agree to
    and accept all the terms of this license and intellectual property
    (trademark/copyright) agreement. If you do not agree to abide by all
    the terms of this agreement, you must cease using and return or
    destroy all copies of Project Gutenberg electronic works in your
    possession. If you paid a fee for obtaining a copy of or access to a
    Project Gutenberg electronic work and you do not agree to be bound
    by the terms of this agreement, you may obtain a refund from the person
    or entity to whom you paid the fee as set forth in paragraph 1.E.8.
    
    1.B. “Project Gutenberg” is a registered trademark. It may only be
    used on or associated in any way with an electronic work by people who
    agree to be bound by the terms of this agreement. There are a few
    things that you can do with most Project Gutenberg electronic works
    even without complying with the full terms of this agreement. See
    paragraph 1.C below. There are a lot of things you can do with Project
    Gutenberg electronic works if you follow the terms of this
    agreement and help preserve free future access to Project Gutenberg
    electronic works. See paragraph 1.E below.
    
    1.C. The Project Gutenberg Literary Archive Foundation (“the
    Foundation” or PGLAF), owns a compilation copyright in the collection
    of Project Gutenberg electronic works. Nearly all the individual
    works in the collection are in the public domain in the United
    States. If an individual work is unprotected by copyright law in the
    United States and you are located in the United States, we do not
    claim a right to prevent you from copying, distributing, performing,
    displaying or creating derivative works based on the work as long as
    all references to Project Gutenberg are removed. Of course, we hope
    that you will support the Project Gutenberg mission of promoting
    free access to electronic works by freely sharing Project Gutenberg
    works in compliance with the terms of this agreement for keeping the
    Project Gutenberg name associated with the work. You can easily
    comply with the terms of this agreement by keeping this work in the
    same format with its attached full Project Gutenberg License when
    you share it without charge with others.
    
    1.D. The copyright laws of the place where you are located also govern
    what you can do with this work. Copyright laws in most countries are
    in a constant state of change. If you are outside the United States,
    check the laws of your country in addition to the terms of this
    agreement before downloading, copying, displaying, performing,
    distributing or creating derivative works based on this work or any
    other Project Gutenberg work. The Foundation makes no
    representations concerning the copyright status of any work in any
    country other than the United States.
    
    1.E. Unless you have removed all references to Project Gutenberg:
    
    1.E.1. The following sentence, with active links to, or other
    immediate access to, the full Project Gutenberg License must appear
    prominently whenever any copy of a Project Gutenberg work (any work
    on which the phrase “Project Gutenberg” appears, or with which the
    phrase “Project Gutenberg” is associated) is accessed, displayed,
    performed, viewed, copied or distributed:
    
        This eBook is for the use of anyone anywhere in the United States and most
        other parts of the world at no cost and with almost no restrictions
        whatsoever. You may copy it, give it away or re-use it under the terms
        of the Project Gutenberg™ License included with this eBook or online
        at www.gutenberg.org. If you
        are not located in the United States, you will have to check the laws
        of the country where you are located before using this eBook.
      
    1.E.2. If an individual Project Gutenberg electronic work is
    derived from texts not protected by U.S. copyright law (does not
    contain a notice indicating that it is posted with permission of the
    copyright holder), the work can be copied and distributed to anyone in
    the United States without paying any fees or charges. If you are
    redistributing or providing access to a work with the phrase “Project
    Gutenberg” associated with or appearing on the work, you must comply
    either with the requirements of paragraphs 1.E.1 through 1.E.7 or
    obtain permission for the use of the work and the Project Gutenberg
    trademark as set forth in paragraphs 1.E.8 or 1.E.9.
    
    1.E.3. If an individual Project Gutenberg electronic work is posted
    with the permission of the copyright holder, your use and distribution
    must comply with both paragraphs 1.E.1 through 1.E.7 and any
    additional terms imposed by the copyright holder. Additional terms
    will be linked to the Project Gutenberg License for all works
    posted with the permission of the copyright holder found at the
    beginning of this work.
    
    1.E.4. Do not unlink or detach or remove the full Project Gutenberg
    License terms from this work, or any files containing a part of this
    work or any other work associated with Project Gutenberg.
    
    1.E.5. Do not copy, display, perform, distribute or redistribute this
    electronic work, or any part of this electronic work, without
    prominently displaying the sentence set forth in paragraph 1.E.1 with
    active links or immediate access to the full terms of the Project
    Gutenberg License.
    
    1.E.6. You may convert to and distribute this work in any binary,
    compressed, marked up, nonproprietary or proprietary form, including
    any word processing or hypertext form. However, if you provide access
    to or distribute copies of a Project Gutenberg work in a format
    other than “Plain Vanilla ASCII” or other format used in the official
    version posted on the official Project Gutenberg website
    (www.gutenberg.org), you must, at no additional cost, fee or expense
    to the user, provide a copy, a means of exporting a copy, or a means
    of obtaining a copy upon request, of the work in its original “Plain
    Vanilla ASCII” or other form. Any alternate format must include the
    full Project Gutenberg License as specified in paragraph 1.E.1.
    
    1.E.7. Do not charge a fee for access to, viewing, displaying,
    performing, copying or distributing any Project Gutenberg works
    unless you comply with paragraph 1.E.8 or 1.E.9.
    
    1.E.8. You may charge a reasonable fee for copies of or providing
    access to or distributing Project Gutenberg electronic works
    provided that:
    
        • You pay a royalty fee of 20% of the gross profits you derive from
            the use of Project Gutenberg works calculated using the method
            you already use to calculate your applicable taxes. The fee is owed
            to the owner of the Project Gutenberg trademark, but he has
            agreed to donate royalties under this paragraph to the Project
            Gutenberg Literary Archive Foundation. Royalty payments must be paid
            within 60 days following each date on which you prepare (or are
            legally required to prepare) your periodic tax returns. Royalty
            payments should be clearly marked as such and sent to the Project
            Gutenberg Literary Archive Foundation at the address specified in
            Section 4, “Information about donations to the Project Gutenberg
            Literary Archive Foundation.”
        
        • You provide a full refund of any money paid by a user who notifies
            you in writing (or by e-mail) within 30 days of receipt that s/he
            does not agree to the terms of the full Project Gutenberg™
            License. You must require such a user to return or destroy all
            copies of the works possessed in a physical medium and discontinue
            all use of and all access to other copies of Project Gutenberg™
            works.
        
        • You provide, in accordance with paragraph 1.F.3, a full refund of
            any money paid for a work or a replacement copy, if a defect in the
            electronic work is discovered and reported to you within 90 days of
            receipt of the work.
        
        • You comply with all other terms of this agreement for free
            distribution of Project Gutenberg™ works.
        
    
    1.E.9. If you wish to charge a fee or distribute a Project
    Gutenberg™ electronic work or group of works on different terms than
    are set forth in this agreement, you must obtain permission in writing
    from the Project Gutenberg Literary Archive Foundation, the manager of
    the Project Gutenberg™ trademark. Contact the Foundation as set
    forth in Section 3 below.
    
    1.F.
    
    1.F.1. Project Gutenberg volunteers and employees expend considerable
    effort to identify, do copyright research on, transcribe and proofread
    works not protected by U.S. copyright law in creating the Project
    Gutenberg™ collection. Despite these efforts, Project Gutenberg™
    electronic works, and the medium on which they may be stored, may
    contain “Defects,” such as, but not limited to, incomplete, inaccurate
    or corrupt data, transcription errors, a copyright or other
    intellectual property infringement, a defective or damaged disk or
    other medium, a computer virus, or computer codes that damage or
    cannot be read by your equipment.
    
    1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right
    of Replacement or Refund” described in paragraph 1.F.3, the Project
    Gutenberg Literary Archive Foundation, the owner of the Project
    Gutenberg™ trademark, and any other party distributing a Project
    Gutenberg™ electronic work under this agreement, disclaim all
    liability to you for damages, costs and expenses, including legal
    fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
    LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
    PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
    TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
    LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
    INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
    DAMAGE.
    
    1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
    defect in this electronic work within 90 days of receiving it, you can
    receive a refund of the money (if any) you paid for it by sending a
    written explanation to the person you received the work from. If you
    received the work on a physical medium, you must return the medium
    with your written explanation. The person or entity that provided you
    with the defective work may elect to provide a replacement copy in
    lieu of a refund. If you received the work electronically, the person
    or entity providing it to you may choose to give you a second
    opportunity to receive the work electronically in lieu of a refund. If
    the second copy is also defective, you may demand a refund in writing
    without further opportunities to fix the problem.
    
    1.F.4. Except for the limited right of replacement or refund set forth
    in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO
    OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
    LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
    
    1.F.5. Some states do not allow disclaimers of certain implied
    warranties or the exclusion or limitation of certain types of
    damages. If any disclaimer or limitation set forth in this agreement
    violates the law of the state applicable to this agreement, the
    agreement shall be interpreted to make the maximum disclaimer or
    limitation permitted by the applicable state law. The invalidity or
    unenforceability of any provision of this agreement shall not void the
    remaining provisions.
    
    1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
    trademark owner, any agent or employee of the Foundation, anyone
    providing copies of Project Gutenberg™ electronic works in
    accordance with this agreement, and any volunteers associated with the
    production, promotion and distribution of Project Gutenberg™
    electronic works, harmless from all liability, costs and expenses,
    including legal fees, that arise directly or indirectly from any of
    the following which you do or cause to occur: (a) distribution of this
    or any Project Gutenberg work, (b) alteration, modification, or
    additions or deletions to any Project Gutenberg work, and (c) any
    Defect you cause.
    
    Section 2. Information about the Mission of Project Gutenberg
    
    Project Gutenberg is synonymous with the free distribution of
    electronic works in formats readable by the widest variety of
    computers including obsolete, old, middle-aged and new computers. It
    exists because of the efforts of hundreds of volunteers and donations
    from people in all walks of life.
    
    Volunteers and financial support to provide volunteers with the
    assistance they need are critical to reaching Project Gutenberg’s
    goals and ensuring that the Project Gutenberg collection will
    remain freely available for generations to come. In 2001, the Project
    Gutenberg Literary Archive Foundation was created to provide a secure
    and permanent future for Project Gutenberg and future
    generations. To learn more about the Project Gutenberg Literary
    Archive Foundation and how your efforts and donations can help, see
    Sections 3 and 4 and the Foundation information page at www.gutenberg.org.
    
    Section 3. Information about the Project Gutenberg Literary Archive Foundation
    
    The Project Gutenberg Literary Archive Foundation is a non-profit
    501(c)(3) educational corporation organized under the laws of the
    state of Mississippi and granted tax exempt status by the Internal
    Revenue Service. The Foundation’s EIN or federal tax identification
    number is 64-6221541. Contributions to the Project Gutenberg Literary
    Archive Foundation are tax deductible to the full extent permitted by
    U.S. federal laws and your state’s laws.
    
    The Foundation’s business office is located at 41 Watchung Plaza #516,
    Montclair NJ 07042, USA, +1 (862) 621-9288. Email contact links and up
    to date contact information can be found at the Foundation’s website
    and official page at www.gutenberg.org/contact
    
    Section 4. Information about Donations to the Project Gutenberg
    Literary Archive Foundation
    
    Project Gutenberg™ depends upon and cannot survive without widespread
    public support and donations to carry out its mission of
    increasing the number of public domain and licensed works that can be
    freely distributed in machine-readable form accessible by the widest
    array of equipment including outdated equipment. Many small donations
    ($1 to $5,000) are particularly important to maintaining tax exempt
    status with the IRS.
    
    The Foundation is committed to complying with the laws regulating
    charities and charitable donations in all 50 states of the United
    States. Compliance requirements are not uniform and it takes a
    considerable effort, much paperwork and many fees to meet and keep up
    with these requirements. We do not solicit donations in locations
    where we have not received written confirmation of compliance. To SEND
    DONATIONS or determine the status of compliance for any particular state
    visit www.gutenberg.org/donate.
    
    While we cannot and do not solicit contributions from states where we
    have not met the solicitation requirements, we know of no prohibition
    against accepting unsolicited donations from donors in such states who
    approach us with offers to donate.
    
    International donations are gratefully accepted, but we cannot make
    any statements concerning tax treatment of donations received from
    outside the United States. U.S. laws alone swamp our small staff.
    
    Please check the Project Gutenberg web pages for current donation
    methods and addresses. Donations are accepted in a number of other
    ways including checks, online payments and credit card donations. To
    donate, please visit: www.gutenberg.org/donate.
    
    Section 5. General Information About Project Gutenberg electronic works
    
    Professor Michael S. Hart was the originator of the Project
    Gutenberg concept of a library of electronic works that could be
    freely shared with anyone. For forty years, he produced and
    distributed Project Gutenberg eBooks with only a loose network of
    volunteer support.
    
    Project Gutenberg eBooks are often created from several printed
    editions, all of which are confirmed as not protected by copyright in
    the U.S. unless a copyright notice is included. Thus, we do not
    necessarily keep eBooks in compliance with any particular paper
    edition.
    
    Most people start at our website which has the main PG search
    facility: www.gutenberg.org.
    
    This website includes information about Project Gutenberg,
    including how to make donations to the Project Gutenberg Literary
    Archive Foundation, how to help produce our new eBooks, and how to
    subscribe to our email newsletter to hear about new eBooks.

    Source: Project Gutenberg ebook #26878. Public-domain status is recorded per item; the licence text above is reproduced unchanged.

    Source
    Project Gutenberg
    Record
    ebook 26878
    Rights
    public domain (US)
    Rendered
    2026-11-22
    Completeness
    First 200,000 characters rendered.