Gutenberg · e01.org
Cover of Transactions of the American Society of Civil Engineers, Vol. LXX, Dec. 1910
Project Gutenberg cover, or a typographic cover where none is held.

Gutenberg · ebook 18747

Transactions of the American Society of Civil Engineers, Vol. LXX, Dec. 1910

by B. S. Randolph · English · public domain in the US

  • Language English
  • PG edition 2006
  • Rights public domain (US)
  • Source Project Gutenberg
0%

Contents

    Transactions of the American Society of Civil Engineers, Vol. LXX, Dec. 1910 by B. S. Randolph is an English public-domain text held from Project Gutenberg (ebook #18747). In the location of new railways and the improvement of lines already in operation, it is now well recognized that large economies can be effected by the careful study of train resistance due to grades and alignment, distributing this resistance so as to secure a minimum cost of operation with the means available for construction.

    Paper No. 1172

    LOCOMOTIVE PERFORMANCE ON GRADES OF

    VARIOUS LENGTHS.

    BY BEVERLY S. RANDOLPH, M. AM. SOC. C. E.

    WITH DISCUSSION BY MESSRS. C. D. PURDON, JOHN C. TRAUTWINE, JR.,

    AND BEVERLY S. RANDOLPH.

    In the location of new railways and the improvement of lines already in operation, it is now well recognized that large economies can be effected by the careful study of train resistance due to grades and alignment, distributing this resistance so as to secure a minimum cost of operation with the means available for construction.

    While engaged in such studies some years ago, the attention of the writer was attracted by the fact that the usual method of calculating the traction of a locomotive--by assuming from 20 to 25% of the weight on the drivers--was subject to no small modification in practice.

    In order to obtain a working basis, for use in relation to this feature, he undertook the collection of data from the practical operation of various roads. Subsequent engagements in an entirely different direction caused this to be laid aside until the present time. The results are given in Table 1, from which it will be seen that the percentage of driver weight utilized in draft is a function of the length as well as the rate of grade encountered in the practical operation of railways.

    In this table, performance will be found expressed as the percentage of the weight on the drivers which is utilized in draft. This is calculated on a basis of 6 lb. per ton of train resistance, for dates prior to 1880, this being the amount given by the late A. M. Wellington, M. Am.

    Soc. C.. E.,[A] and 4.7 lb. per ton for those of 1908-10, as obtained by A. C. Dennis, M. Am. Soc. C. E.,[B] assuming this difference to represent the advance in practice from 1880 to the present time. Most of the data have been obtained from the "Catalogue of the Baldwin Locomotive Works" for 1881, to which have been added some later figures from "Record No. 65" of the same establishment, and also some obtained by the writer directly from the roads concerned. Being taken thus at random, the results may be accepted as fairly representative of American practice.

    Attention should be directed to the fact that the performance of the 10-34 E, Consolidation locomotive on the Lehigh Valley Railroad in 1871 is practically equal to that of the latest Mallet compounds on the Great Northern Railway. In other words, in the ratio between the ability to produce steam and the weight on the drivers there has been no change in the last forty years. This would indicate that the figures are not likely to be changed much as long as steam-driven locomotives are in use. What will obtain with the introduction of electric traction is "another story."

    These results have also been platted, and are presented in Fig. 1, with the lengths of grade as abscissas and the percentages of weight utilized as ordinates. The curve sketched to represent a general average will show the conditions at a glance.

    The results may at first sight seem irregular, but the agreement is really remarkable when the variety of sources is considered; that in many cases the "reputed" rate of grade is doubtless given without actual measurement; that the results also include momentum, the ability to utilize which depends on the conditions of grade, alignment, and operating practice which obtain about the foot of each grade; and that the same amount of energy due to momentum will carry a train farther on a light grade than on a heavy one.

    There are four items in Table 1 which vary materially from the general consensus. For Item 9, the authorities of the road particularly state that their loads are light, because, owing to the congested condition of their business, their trains must make fast time. Item 10 represents very old practice, certainly prior to 1882, and is "second-hand." The load consisted of empty coal cars, and the line was very tortuous, so that it is quite probable that the resistance assumed in the calculation is far below the actual. Items 15 and 17 are both high.

    To account for this, it is to be noted that this road has been recently completed, regardless of cost in the matter of both track and rolling stock, and doubtless represents the highest development of railroad practice. Its rolling stock is all new, and is probably in better condition to offer low resistance than it will ever be again, and there were no "foreign" cars in the trains considered.

    The train resistance, therefore, may be naturally assumed to be much less than that of roads hauling all classes of cars, many of which are barely good enough to pass inspection. As the grades are light in both cases, this feature of train resistance is larger than in items including heavier grades. Attention should be called to the fact that a line connecting the two points representing these items on Fig.

    1 would make only a small angle with the sketched curve, and would be practically parallel to a similar line connecting the points represented by Items 13 and 16. There is, therefore, an agreement of ratios, which is all that needs consideration in this discussion.

    [Illustration: FIG. 1.--DIAGRAM SHOWING PERCENTAGE OF WEIGHT ON DRIVERS

    WHICH IS UTILIZED IN TRACTION ON GRADES OF VARIOUS LENGTHS]

    Wellington, in his monumental work on railway location, presents a table of this character. The percentages of weight on the drivers which is utilized in draft show the greatest irregularity. He does not give the length of the grades considered, so that it is impossible to say how far the introduction of this feature would have contributed to bring order out of the chaos.

    In his discussion of the table he admits the unsatisfactory character of the results, and finally decides on 25% as a rough average, "very approximately the safe operating load in regular service." He further states that a number of results, which he omits for want of space, exceeds 33 per cent. The highest shown in Table 1 will be found in Item 1 (0.06 mile, 0.066 grade), showing 33 per cent. There is no momentum effect here, as the grade is a short incline extending down to the river, and the start is necessarily a "dead" one.

    The reports of Item 3, which shows 31%, and Item 5, which shows 27%, state specifically that the locomotives will stop and start the loads given at any point on the grade.

    The results of a series of experiments reported by Mr. A. C. Dennis in his paper, "Virtual Grades for Freight Trains," previously referred to, indicate a utilization of somewhat more than 23%, decreasing with the speed.

    All this indicates that the general failure of locomotives to utilize more than from 16 to 18% on long grades, as shown by Table 1, can only be due to the failure of the boilers to supply the necessary steam.

    While the higher percentage shown for the shorter grades may be ascribed largely to momentum present when the foot of the grade is reached, the energy due to stored heat is responsible for a large portion of it.

    When a locomotive has been standing still, or running with the steam consumption materially below the production, the pressure accumulates until it reaches the point at which the safety valve is "set." This means that the entire machine is heated to a temperature sufficient to maintain this pressure in the boiler. When the steam consumption begins to exceed the production, this temperature is reduced to a point where the consumption and production balance.

    The heat represented by this difference in temperature has passed into the steam used, thus adding to the energy supplied by the combustion going on in the furnace. The engines, therefore, are able to do considerably more work during the time the pressure is falling than they can do after the fall has ceased.

    The curve in Fig. 1 would indicate that the energy derived from the two sources just discussed is practically dissipated at 15 miles, though the position of the points representing Items 16, 18, 19, 20, and 21 would indicate that this takes place more frequently between 10 and 12 miles.

    From this point onward the performance depends on the efficiency of the steam production, which does not appear to be able to utilize more than 16% of the weight on the drivers. The diagrams presented by Mr. Dennis in his paper on virtual grades, and by John A. Fulton, M. Am. Soc.

    C. E., in his discussion of that paper, indicate that similar results would be shown were they extended to include the distance named.

    From this it would appear that a locomotive is capable of hauling a larger train on grades less than 10 miles in length than on longer grades, and that, even when unexpectedly stopped, it is capable of starting again as soon as the steam pressure is sufficiently built up.

    Conversely, it should be practicable to use a higher rate of ascent on shorter grades on any given line without decreasing the load which can be hauled over it. In other words, what is known as the "ruling grade" is a function, strictly speaking, of the length as well as the rate of grade.

    In any discussions of the practicability of using a higher rate on the short grades, which the writer has seen, the most valid objection has appeared to be the danger of stalling and consequent delay. As far as momentum is relied on, this objection is valid. Within the limits of the load which can be handled by the steam, it has small value, as it is only a question of waiting a few minutes until the pressure can be built up to the point at which the load can be handled. As this need only be an occasional occurrence, it is not to be balanced against any material saving in cost of construction.

    The writer does not know of any experiments which will throw much light on the value of heat storage as separated from momentum, though the following discussion may prove suggestive:

    A train moving at a rate of 60 ft. per sec., and reaching the foot of a grade, will have acquired a "velocity head" of 56.7 ft., equivalent to stored energy of 56.7 × 2,000 = 113,400 ft-lb. per ton. On a 0.002 grade (as in Item 15 of Table 1) the resistance would be, gravity 4 lb. + train 4.7 lb. = 8.7 lb., against which the energy above given would carry the train through 113,400 ÷ 8.7 = 13,034 ft., say, 2.5 miles, leaving 5 miles to be provided for by the steam production.

    Examining the items in the table having grades in excess of 10 miles, it will be noted that 16% is about all the weight on drivers which can be utilized by the current supply of steam. In Item 15 the energy derived from all sources is equivalent to 24.3%; hence the stored heat may be considered as responsible for an equivalent of 24.3% - 16% = 8.3% for a distance of 5 miles.

    TABLE 1.

    Item No. |Length of grade, in miles. | |Rate of grade. | | |Maximum curvature. | | | |Compensation. | | | | |Gross weight of load, in tons. | | | | | |Weight of tender, in tons. | | | | | | |Weight of locomotive, in tons. | | | | | | | |Weight on drivers, in tons. | | | | | | | | |Percentage of weight on | | | | | | | | |drivers utilized in draft. | | | | | | | | | |Class. | | | | | | | | | | | | | | | | | | | | --+-----+------+------+----+-----+--+-----+-----+-----+--------------------

    1| 0.06|0.066 | | | 115| | 37.5| 29 |0.358| 8-28-1/3 C

    2| 0.33|0.0203|25°20'| | 242|25| 35 | 23 |0.285| 8-28 C

    3| 1.0 |0.06 |16° |0.05| 192|22| 57.5| 50 |0.310|10-36 E

    4| 1.3 |0.0127| | | 600|16| 40 | 32.5|0.300|Mogul.

    5| 1.4 |0.0128| 3°12'| | 750|15| 51 | 44 |0.270|10-34 E

    6| 2.0 |0.01 | | |1,000|15| 51 | 44 |0.291|10-34 E

    7| 2.2 |0.013 | 3° | | 725|15| 51 | 44 |0.245|10-34 E

    8| 2.5 |0.0144| 6° | | 400|27| 42 | 32 |0.237|10-32 E

    9| 2.5 |0.004 | | |2,700|70| 96.7| 85.8|0.207| H 6 - A

    10| 3.5 |0.033 |14° | | 100|25| 35 | 35 |0.160|

    11| 3.6 |0.035 |10° |0.05| 236|22| 57.5| 50 |0.245|10-36 E

    12| 4.0 |0.0085| 4° | |1,020|30| 51 | 44 |0.256|10-34 E

    13| 6.0 |0.0145| | | 308|25| 38 | 28 |0.207|10-28 D

    14| 6.0 |0.020 |10° |0.05| 460|32| 57.5| 50 |0.242|10-34 E

    15| 7.5 |0.002 | | C |6,152|86|134.5|109.5|0.243|Mallet. 16| 9.75|0.018 | | | 200|18| 29 | 29 |0.170| 17|10.0 |0.006 | | C |6,173|86|299 |265 |0.203|Mallet.

    18|12.0 |0.018 |10° | | 280|30| 51 | 44 |0.160|10-34 E

    19|12.0 |0.022 | | | 850|74|175 |156 |0.166|D-D 16

    20|13.0 |0.022 | | | 800|74|177 |158 |0.153|D-D 1

    21|13.0 |0.022 |14° | | 415|50| 91 | 83 |0.154|Consol.

    22|16.0 |0.0044| | | 950|30| 51 | 44 |0.164|10-34 E

    23|20.0 |0.022 | | | 500|62| 97.5| 90 |0.170|F 8, Consol. 24|20.0 |0.022 | | | 800|74|177 |158 |0.159|L-1, Mallet.

    |Maker. |Railroad. |Reporting Officer. |Year.
    --+--------+----------------------------+-----------------------------+-----
    1|Baldwin.|Morgan's Louisiana & Texas |Newell Tilton, Asst. Supt. |1880
    2| " |Long Island |S. Spencer, Gen. Supt. |1878
    3| " |Atchison, Topeka & Santa Fe |J. D. Burr, Asst. Engr. |1879
    4| " |Chillan & Talcahuana |J. E. Martin, Local Supt. |1879
    5| " |Chicago, Burlington & Quincy|H. B.

    Stone |1880
    6| " |Chicago, Burlington & Quincy| " |1880
    7| " |Chicago, Burlington & Quincy| " |1880
    8| " |St. Louis & San Francisco |C. W. Rogers, Gen. Mgr. |1879
    9|Pa. R.R |Cumberland Valley. | |1910
    10| | | |1910
    11|Baldwin.|Atchison, Topeka & Santa Fe |J. D. Burr, Asst. Engr. |1879
    12| " |Missouri Pacific |John Hewitt, Supt. M. P. |1880
    13| " |Western Maryland |D.

    Holtz, M. of Mach'y. |1878
    14| " |Atchison, Topeka & Santa Fe |J. D. Burr, Asst. Engr. |1879
    15| " |Virginian Ry. | |1910
    16| |Pennsylvania | |1910
    17|Baldwin.|Virginian Ry. | |1910
    18| " |Lehigh Valley, Wyoming Div. |A. Mitchell, Div. Supt. |1871
    19| " |Great Northern |Grafton Greenough. |1908
    20| " |Great Northern |Grafton Greenough. |1908
    21| " |Baltimore & Ohio |F. E. Blaser, Div.

    Supt. |1910
    22| " |Central of N. J. |W. W. Stearns, Asst.Gen.Supt.|1880
    23| " |Great Northern |Grafton Greenough. |1908
    24| " |Great Northern |Grafton Greenough. |1906
    ============================================================================

    |Source of Data. |Remarks.
    --+-----------------------------------------+---------------------------------
    1|Baldwin Catalogue, 1881, p.

    134 |
    2| " " 1881, " 72 |10 miles per hour.
    3| " " 1881, " 115 | 8 " " "
    | | Stops and starts on grade.
    4| " " 1881, " 100 |
    5| " " 1881, " 116 |Stops and starts at any point
    | | on grade.
    6| " " 1881, " 116 |
    7| " " 1881, " 116 |
    8| " " 1881, " 87 |
    9| |
    10|Trautwine's Pocket Book, Ed.

    1882, p. 412|Empty cars; many curves and
    | | reversions.
    11|Baldwin Catalogue, 1881, p. 114 |
    12| " " 1881, " 112 |
    13| " " 1881, " 86 |12 miles per hour.
    14| " " 1881, " 114 | 8 " " "
    15|Engineering News, Jan. 13, 1910. |
    16|Trautwine's Pocket Book, Ed. 1882, p. 412|
    17|Engineering News, Jan. 13, 1910. |Road locomotive and helper.
    18|Baldwin Catalogue, 1881, p. 112 |
    19|Baldwin Loco. Wks. Record, No. 65, p.

    29|
    20|Baldwin Loco. Wks. Record, No. 65, p. 29|
    21| |Very crooked line. Uncompensated.
    22|Baldwin Catalogue, 1881, p. 113 |
    23|Baldwin Loco. Wks. Record, No. 65, p. 29|
    24|Baldwin Loco. Wks. Record, No. 65, p. 29|
    ==============================================================================

    In proportioning grade resistance for any line, therefore, a locomotive may be counted on to utilize 24.3% of the weight on the drivers for a distance of 5 miles on a 0.002 grade without any assistance from momentum, and, in the event of an unexpected stop, should be able, as soon as a full head of steam is built up, to start the train and carry it over the grade. This is probably a maximum, considering the condition of the equipment of this Virginian Railway, as previously mentioned.

    Treating Item 14 in the same way, a distance of 2,310 ft. is accounted for by momentum, leaving, say, 5.5 miles for the steam, or the length of a 0.02 grade on which a locomotive may be loaded on a basis of tractive power equal to 24.2% of the weight on the drivers.

    From these figures it may be concluded that on lines having grades from 12 to 15 or more miles in length, grades of 3 to 5 miles in length may be inserted having rates 50% in excess of that of the long grades, without decreasing the capacity of the line. This statement, of course, is general in its bearings, each case being subject to its especial limitations, and subject to detailed calculations.

    It may be noted that the velocity of 60 ft. per sec., assumed at the foot of the grade, is probably higher than should be expected in practice; it insures, on the other hand, that quite enough has been allowed for momentum, and that the results are conservative.

    Arguments like the foregoing are always more or less treacherous; being based on statistics, they are naturally subject to material modifications in the presence of a larger array of data, therefore, material assistance in reaching practical conclusions can be given by the presentation of additional data.

    DISCUSSION

    C. D. PURDON, M. AM. SOC. C. E. (by letter).--Some years ago the writer, in making studies for grade revision, found that the tractive power of a locomotive up grade becomes less as the length of the grade increases, and in some unknown proportion. This was a practical confirmation of the saying of locomotive engineers, that the engine "got tired" on long grades. On a well-known Western railroad, with which the writer is familiar, experiments were made for the purpose of rating its locomotives.

    The locomotives were first divided into classes according to their tractive power, this being calculated by the usual rule, with factors of size of cylinders, boiler pressure, and diameter of drivers, also by taking one-fourth of the weight on the drivers, and using the lesser of the two results as the tractive power.

    Locomotives of different classes, and hauling known loads, were run over a freight division, the cars being weighed for the purpose; thus the maximum load which could be handled over a division, or different parts of a division, was ascertained, and this proportion of tonnage to tractive power was used in rating all classes.

    Of course, this method was not mathematically accurate, as the condition of track, the weather, and the personal equation of the locomotive engineers all had an effect, but, later, when correcting the rating by tests with dynamometers, it was found that the results were fairly practical.

    There were three hills where the rate of grade was the same as the rest of the division, but where the length was much in excess of other grades of the same rate.

    Designating these hills as A, B, and C, the lengths are, respectively, 2.44, 3.57, and 4.41 miles. There were no other grades of the same rate exceeding 1 mile.

    In one class of freight engines, 10-wheel Brooks, the weight of the engine was 197,900 lb.; tender, 132,800 lb.; weight on drivers, 142,600 lb.; boiler pressure, 200 lb.; and tractive power of cylinders, 33,300 lb.

    On Hill A these engines are rated at 865 tons, as compared with 945 on other parts of the division. As the engine weighs 165 tons and the caboose 15 tons, 180 tons should be added, making the figures, 1,045 and 1,125 tons. Thus the length of the grade, 2.44 miles, makes the tractive power on it 92% of that on shorter grades.

    On Hill B, the rating, adding 180 tons as above, is 1,160 and 1,230 tons, respectively, giving 94% for 3.57 miles.

    On Hill C, the rating, with 180 tons added, is 1,130 and 1,230 tons, making 92% for 4.41 miles.

    Taking the same basis as the author, namely, 4.7 lb. per ton, rate of grade × 20, and weight on drivers, gives:

    Hill A, 18.078%, remainder of division, 19.462% Hill B, 20.068%, " " " 21.279% Hill C, 19.549%, " " " 21.279%

    It will be noted that the author uses the weight on the drivers as the criterion, but the tractive power is not directly as the weight on the drivers, some engines being over-cylindered, or under-cylindered; in the class of engines above mentioned the tractive power is 23.35% of the weight on the drivers.

    The writer made a study of several dynamometer tests on Hill C. There is a grade of the same rate, about 1 mile long, near this hill, and a station near its foot, but there is sufficient level grade between this station and the foot of the hill to get a good start.

    All the engines of the above class, loaded for Hill C, gained speed on the 1-mile grade, but began to fall below the theoretical speed at a point about 2-1/4 miles from the foot of the hill. This condition occurred when the trains stopped at the station and also when they passed it at a rate of some 16 or 18 miles per hour, the speed becoming less and less as the top of the hill was approached.

    The writer concludes that the author might stretch his opinion as to using heavier rates of grade on shorter hills than 10 miles, and indeed his diagram seems to intimate as much, and that, for economical operation, the maximum rate of grade should be reduced after a length of about 2 miles has been reached, and more and more in proportion to the length of the hill, in order that the same rating could be applied all over a division.

    This conclusion might be modified by local conditions, such as an important town where cars might be added to or taken from the train.

    While it does not seem practicable to the writer to calculate what the reduction of rate of grade should be, a consensus of results of operation on different lengths of grade might give sufficient data to reach some conclusion on the matter.

    The American Railway Engineering and Maintenance of Way Association has a Committee on "Railway Economics," which is studying such matters, but so far as the writer knows it has not given this question any consideration.

    The writer hopes that the author will follow up this subject, and that other members will join, as a full discussion will no doubt bring some results on a question which seems to be highly important.

    JOHN C. TRAUTWINE, JR., ASSOC. AM. SOC. C. E. (by letter).--In his collection of data, Mr. Randolph includes two ancient cases taken from the earliest editions (1872-1883) of Trautwine's "Civil Engineer's Pocket-Book," referring to performances on the Mahanoy and Broad Mountain Railroad (now the Frackville Branch of the Reading) and on the Pennsylvania Railroad, respectively.

    In the private notes of John C. Trautwine, Sr., these two cases are recorded as follows:

    "On the Mahanoy & Broad Mtn. R. R., tank Engines of 35 tons, all
    on 8 drivers
    , draw 40 empty coal cars weighing 100 tons, up a
    continuous grade of 175 ft. per mile for 3-1/2 miles; & around
    curves of 450, 500, 600 ft. &c. rad., at 8 miles an hour. (1864)
    This is equal to 77-14/100 tons for a 27-ton engine." (Vol. III, p.
    176.)

    "On the Penn Central 95 ft. grades for 9-3/4 miles, a 29-ton engine
    all on 8 drivers takes 125 tons of freight and 112 tons of engine,
    tender, & cars, in all 237 tons,[C] and a passenger engine takes up
    3 cars at 24 miles an hour (large 8 wheels). When more than 3, an
    auxiliary engine."

    It will be seen that Mr. Randolph is well within bounds in ascribing to the Mahanoy and Broad Mountain case (his No. 10) a date "certainly prior to 1882," the date being given, in the notes, as 1864; while another entry just below it, for the Pennsylvania Railroad case, is dated 1860.

    It also seems, as stated by Mr. Randolph, quite probable that the frictional resistance (6 lb. per 2,000 lb.) assumed by him in the calculation is far below the actual for this Case 10. The small, empty, four-wheel cars weighed only 4,400 lb. each. Furthermore, the "tons," in the Trautwine reports of these experiments, were tons of 2,240 lb. On the other hand, the maximum curvature was 12° 45' (not 14°, as given by the author), and the engine was a tank locomotive, whereas the author has credited it with a 25-ton tender.

    After making all corrections, it will be found that, in order to bring the point, for this Case 10, up to the author's curve, instead of his 6 lb. per 2,000 lb., a frictional resistance of 66 lb. per 2,000 lb. would be required, a resistance just equal to the gravity resistance on the 3.3% grade, making a total resistance of 132 lb. per 2,000 lb.

    While this 66 lb. per ton is very high, it is perhaps not too high for the known conditions, as above described. For modern rolling stock, Mr.

    A. K. Shurtleff gives the formula:[D]

    Frictional resistance, on tangent, } in pounds per 2,000 pounds } = 1 + 90 ÷ C,

    where C = weight of car and load, in tons of 2,000 lb. This would give, for 4,400-lb. (2.2-ton) cars, a frictional resistance of 42 lb. per 2,000 lb.; and, on the usual assumption of 0.8 lb. per 2,000 lb. for each degree of curvature, the 12.75° curves of this line would give 10 lb. per ton additional, making a total of 52 lb. per 2,000 lb. over and above grade resistance, under modern conditions.

    In the 9th to 17th editions of Trautwine (1885-1900), these early accounts were superseded by numerous later instances, including some of those quoted by the author.

    In the 18th and 19th editions (1902-1909) are given data respecting performances on the Catawissa Branch of the Reading (Shamokin Division) in 1898-1901. These give the maximum and minimum loads hauled up a nearly continuous grade of 31.47 ft. per mile (0.59%) from Catawissa to Lofty (34.03 miles) by engines of different classes, with different helpers and without helpers.

    Table 2 (in which the writer follows the author in assuming frictional resistance at 4.7 lb. per 2,000 lb.) shows the cases giving the maximum and minimum values of the quantity represented by the ordinates in the author's diagram, namely, "Traction, in percentage of weight on drivers."

    It will be seen that the maximum percentage (16.1) is practically identical with that found by the author (16) for grade lengths exceeding 17 miles.

    Near the middle of the 34-mile distance there is a stretch of 1.51 miles, on which the average grade is only 5.93 ft. per mile (0.112%), and this stretch divides the remaining distance into two practically continuous grades, 19.39 and 13.13 miles long, respectively; but, as the same loads are hauled over these two portions by the same engines, the results are virtually identical, the maxima furnishing two more points closely coinciding with the author's diagram.

    TABLE 2.--TRACTIVE FORCE, CATAWISSA TO LOFTY.

    Length of grade, in miles | | 34.03
    | |
    Grade {in feet per mile | | 31.47
    {percentage |A | 0.597
    | |
    Resistances, in pounds per 2,000 lb., | |
    Gravity (=20 A) = 11.94.

    Friction = 4.70 |B | 16.64
    | |
    Load: | Cars. | Locomotive.| Tender. | |
    Maximum[E] | 1,561 | 44.60 | 25.25 |C | 1,631
    Minimum[F] | 1,031 | 60.50 | 34.50 |C | 1,126
    | |
    Traction (= B C ÷ 2,000 ) Maximum[E] |D | 13.60
    Minimum[F] |D | 9.38
    Weight on Drivers: | Locomotive.| Helper. | |
    Maximum[E] | 21.60 | 63.00 |E | 84.60
    Minimum[F] | 47.00 | 72.00 |E | 119.00
    | |
    Percentage ( = D ÷ E ). | |
    Maximum |F | 16.1
    Minimum |F | 7.9
    ##

    FOOTNOTES:

    [Footnote E: Giving maximum values of percentage, F.]

    [Footnote F: Giving minimum values of percentage, F.]

    BEVERLY S. RANDOLPH, M. AM. SOC. C. E. (by letter).--The percentages given by Mr. Purdon would seem to indicate that the length of the grades did not affect the loads in the cases cited, but these percentages are so much below those shown in the table, for similar distances, as to indicate some special conditions which the writer has been unable to find in the text.

    The use of the percentage of weight on drivers which is utilized in traction as a measure of the efficiency of the locomotive, while, probably, not applicable to individual machines, is sound for the purposes of comparison of results to be obtained on various portions of a line as far as affected by conditions of grade and alignment. It has the advantage of disregarding questions of temperature, condition of track, character of fuel, etc., which, being the same on all portions of the line, naturally balance and do not affect the comparison.

    It is, of course, simply a method of expressing the final efficiency of the various parts of the locomotive, and, since it depends entirely on actual results already accomplished, leaves no room for difference of opinion or theoretical error.

    The writer has always considered an "under-cylindered" locomotive as a defective machine. All weight is a distinct debit, in the shape of wear and tear of track and running gear, resistance due to gravity on grades, interest on cost, etc. When this weight fails to earn a credit in the way of tractive efficiency, it should not be present.

    The statement relative to the performance of locomotives on "Hill C" is interesting, especially in that it appears to have been immaterial whether they made a dead start after stopping at the station or approached the foot of the hill at 16 to 18 miles per hour. The momentum would appear to be an insignificant factor.

    It is gratifying to note that Mr. Trautwine has been able to brace up the weak member of Table 1 so completely with his detailed data; also that his other results strengthen the conclusions reached in the paper.

    FOOTNOTES:

    [Footnote A: "The Economic Theory of Railway Location," 1887 edition,
    p. 502.]

    [Footnote B: Transactions, Am. Soc. C. E., Vol. L, p. 1.]

    [Footnote C: "Nearly 200 tons exclusive of eng. & ten." (Vol. III,
    p. 176-1/10.)]

    [Footnote D: American Railway Engineering and Maintenance of Way
    Association, Bulletin 84, February, 1907, p. 99.]

    Edition notice Project Gutenberg source, credits & licence

    The reading text above is the public-domain work. The Project Gutenberg header, production credits and licence are kept here as provenance rather than shown before the book.

    Title
    Transactions of the American Society of Civil Engineers, Vol. LXX, Dec. 1910
    Author
    B. S. Randolph
    Release date
    July 3, 2006 [eBook #18747]
    Language
    English
    Credits
    Produced by Juliet Sutherland, Sigal Alon and the Online
    Transcriber and production notes
    Produced by Juliet Sutherland, Sigal Alon and the Online
    Distributed Proofreading Team at http://www.pgdp.net
    Front matter as received (title page, contents)
    AMERICAN SOCIETY OF CIVIL ENGINEERS
    
    INSTITUTED 1852
    
    
    TRANSACTIONS
    Header as received
    The Project Gutenberg eBook of Transactions of the American Society of Civil Engineers, Vol. LXX, Dec. 1910
        
    This eBook is for the use of anyone anywhere in the United States and
    most other parts of the world at no cost and with almost no restrictions
    whatsoever. You may copy it, give it away or re-use it under the terms
    of the Project Gutenberg License included with this eBook or online
    at www.gutenberg.org. If you are not located in the United States,
    you will have to check the laws of the country where you are located
    before using this eBook.
    
    Title: Transactions of the American Society of Civil Engineers, Vol. LXX, Dec. 1910
    
    Author: B. S. Randolph
    
    
            
    Release date: July 3, 2006 [eBook #18747]
    
    Language: English
    
    Other information and formats: www.gutenberg.org/ebooks/18747
    
    Credits: Produced by Juliet Sutherland, Sigal Alon and the Online
            Distributed Proofreading Team at http://www.pgdp.net
    Full Project Gutenberg licence
        
    
    Updated editions will replace the previous one—the old editions will
    be renamed.
    
    Creating the works from print editions not protected by U.S. copyright
    law means that no one owns a United States copyright in these works,
    so the Foundation (and you!) can copy and distribute it in the United
    States without permission and without paying copyright
    royalties. Special rules, set forth in the General Terms of Use part
    of this license, apply to copying and distributing Project
    Gutenberg™ electronic works to protect the PROJECT GUTENBERG™
    concept and trademark. Project Gutenberg is a registered trademark,
    and may not be used if you charge for an eBook, except by following
    the terms of the trademark license, including paying royalties for use
    of the Project Gutenberg trademark. If you do not charge anything for
    copies of this eBook, complying with the trademark license is very
    easy. You may use this eBook for nearly any purpose such as creation
    of derivative works, reports, performances and research. Project
    Gutenberg eBooks may be modified and printed and given away—you may
    do practically ANYTHING in the United States with eBooks not protected
    by U.S. copyright law. Redistribution is subject to the trademark
    license, especially commercial redistribution.
    
    
    START: FULL LICENSE
    
    THE FULL PROJECT GUTENBERG™ LICENSE
    
    PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK
    
    To protect the Project Gutenberg™ mission of promoting the free
    distribution of electronic works, by using or distributing this work
    (or any other work associated in any way with the phrase “Project
    Gutenberg”), you agree to comply with all the terms of the Full
    Project Gutenberg License available with this file or online at
    www.gutenberg.org/license.
    
    Section 1. General Terms of Use and Redistributing Project Gutenberg
    electronic works
    
    1.A. By reading or using any part of this Project Gutenberg
    electronic work, you indicate that you have read, understand, agree to
    and accept all the terms of this license and intellectual property
    (trademark/copyright) agreement. If you do not agree to abide by all
    the terms of this agreement, you must cease using and return or
    destroy all copies of Project Gutenberg electronic works in your
    possession. If you paid a fee for obtaining a copy of or access to a
    Project Gutenberg electronic work and you do not agree to be bound
    by the terms of this agreement, you may obtain a refund from the person
    or entity to whom you paid the fee as set forth in paragraph 1.E.8.
    
    1.B. “Project Gutenberg” is a registered trademark. It may only be
    used on or associated in any way with an electronic work by people who
    agree to be bound by the terms of this agreement. There are a few
    things that you can do with most Project Gutenberg electronic works
    even without complying with the full terms of this agreement. See
    paragraph 1.C below. There are a lot of things you can do with Project
    Gutenberg electronic works if you follow the terms of this
    agreement and help preserve free future access to Project Gutenberg
    electronic works. See paragraph 1.E below.
    
    1.C. The Project Gutenberg Literary Archive Foundation (“the
    Foundation” or PGLAF), owns a compilation copyright in the collection
    of Project Gutenberg electronic works. Nearly all the individual
    works in the collection are in the public domain in the United
    States. If an individual work is unprotected by copyright law in the
    United States and you are located in the United States, we do not
    claim a right to prevent you from copying, distributing, performing,
    displaying or creating derivative works based on the work as long as
    all references to Project Gutenberg are removed. Of course, we hope
    that you will support the Project Gutenberg mission of promoting
    free access to electronic works by freely sharing Project Gutenberg
    works in compliance with the terms of this agreement for keeping the
    Project Gutenberg name associated with the work. You can easily
    comply with the terms of this agreement by keeping this work in the
    same format with its attached full Project Gutenberg License when
    you share it without charge with others.
    
    1.D. The copyright laws of the place where you are located also govern
    what you can do with this work. Copyright laws in most countries are
    in a constant state of change. If you are outside the United States,
    check the laws of your country in addition to the terms of this
    agreement before downloading, copying, displaying, performing,
    distributing or creating derivative works based on this work or any
    other Project Gutenberg work. The Foundation makes no
    representations concerning the copyright status of any work in any
    country other than the United States.
    
    1.E. Unless you have removed all references to Project Gutenberg:
    
    1.E.1. The following sentence, with active links to, or other
    immediate access to, the full Project Gutenberg License must appear
    prominently whenever any copy of a Project Gutenberg work (any work
    on which the phrase “Project Gutenberg” appears, or with which the
    phrase “Project Gutenberg” is associated) is accessed, displayed,
    performed, viewed, copied or distributed:
    
        This eBook is for the use of anyone anywhere in the United States and most
        other parts of the world at no cost and with almost no restrictions
        whatsoever. You may copy it, give it away or re-use it under the terms
        of the Project Gutenberg™ License included with this eBook or online
        at www.gutenberg.org. If you
        are not located in the United States, you will have to check the laws
        of the country where you are located before using this eBook.
      
    1.E.2. If an individual Project Gutenberg electronic work is
    derived from texts not protected by U.S. copyright law (does not
    contain a notice indicating that it is posted with permission of the
    copyright holder), the work can be copied and distributed to anyone in
    the United States without paying any fees or charges. If you are
    redistributing or providing access to a work with the phrase “Project
    Gutenberg” associated with or appearing on the work, you must comply
    either with the requirements of paragraphs 1.E.1 through 1.E.7 or
    obtain permission for the use of the work and the Project Gutenberg
    trademark as set forth in paragraphs 1.E.8 or 1.E.9.
    
    1.E.3. If an individual Project Gutenberg electronic work is posted
    with the permission of the copyright holder, your use and distribution
    must comply with both paragraphs 1.E.1 through 1.E.7 and any
    additional terms imposed by the copyright holder. Additional terms
    will be linked to the Project Gutenberg License for all works
    posted with the permission of the copyright holder found at the
    beginning of this work.
    
    1.E.4. Do not unlink or detach or remove the full Project Gutenberg
    License terms from this work, or any files containing a part of this
    work or any other work associated with Project Gutenberg.
    
    1.E.5. Do not copy, display, perform, distribute or redistribute this
    electronic work, or any part of this electronic work, without
    prominently displaying the sentence set forth in paragraph 1.E.1 with
    active links or immediate access to the full terms of the Project
    Gutenberg License.
    
    1.E.6. You may convert to and distribute this work in any binary,
    compressed, marked up, nonproprietary or proprietary form, including
    any word processing or hypertext form. However, if you provide access
    to or distribute copies of a Project Gutenberg work in a format
    other than “Plain Vanilla ASCII” or other format used in the official
    version posted on the official Project Gutenberg website
    (www.gutenberg.org), you must, at no additional cost, fee or expense
    to the user, provide a copy, a means of exporting a copy, or a means
    of obtaining a copy upon request, of the work in its original “Plain
    Vanilla ASCII” or other form. Any alternate format must include the
    full Project Gutenberg License as specified in paragraph 1.E.1.
    
    1.E.7. Do not charge a fee for access to, viewing, displaying,
    performing, copying or distributing any Project Gutenberg works
    unless you comply with paragraph 1.E.8 or 1.E.9.
    
    1.E.8. You may charge a reasonable fee for copies of or providing
    access to or distributing Project Gutenberg electronic works
    provided that:
    
        • You pay a royalty fee of 20% of the gross profits you derive from
            the use of Project Gutenberg works calculated using the method
            you already use to calculate your applicable taxes. The fee is owed
            to the owner of the Project Gutenberg trademark, but he has
            agreed to donate royalties under this paragraph to the Project
            Gutenberg Literary Archive Foundation. Royalty payments must be paid
            within 60 days following each date on which you prepare (or are
            legally required to prepare) your periodic tax returns. Royalty
            payments should be clearly marked as such and sent to the Project
            Gutenberg Literary Archive Foundation at the address specified in
            Section 4, “Information about donations to the Project Gutenberg
            Literary Archive Foundation.”
        
        • You provide a full refund of any money paid by a user who notifies
            you in writing (or by e-mail) within 30 days of receipt that s/he
            does not agree to the terms of the full Project Gutenberg™
            License. You must require such a user to return or destroy all
            copies of the works possessed in a physical medium and discontinue
            all use of and all access to other copies of Project Gutenberg™
            works.
        
        • You provide, in accordance with paragraph 1.F.3, a full refund of
            any money paid for a work or a replacement copy, if a defect in the
            electronic work is discovered and reported to you within 90 days of
            receipt of the work.
        
        • You comply with all other terms of this agreement for free
            distribution of Project Gutenberg™ works.
        
    
    1.E.9. If you wish to charge a fee or distribute a Project
    Gutenberg™ electronic work or group of works on different terms than
    are set forth in this agreement, you must obtain permission in writing
    from the Project Gutenberg Literary Archive Foundation, the manager of
    the Project Gutenberg™ trademark. Contact the Foundation as set
    forth in Section 3 below.
    
    1.F.
    
    1.F.1. Project Gutenberg volunteers and employees expend considerable
    effort to identify, do copyright research on, transcribe and proofread
    works not protected by U.S. copyright law in creating the Project
    Gutenberg™ collection. Despite these efforts, Project Gutenberg™
    electronic works, and the medium on which they may be stored, may
    contain “Defects,” such as, but not limited to, incomplete, inaccurate
    or corrupt data, transcription errors, a copyright or other
    intellectual property infringement, a defective or damaged disk or
    other medium, a computer virus, or computer codes that damage or
    cannot be read by your equipment.
    
    1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right
    of Replacement or Refund” described in paragraph 1.F.3, the Project
    Gutenberg Literary Archive Foundation, the owner of the Project
    Gutenberg™ trademark, and any other party distributing a Project
    Gutenberg™ electronic work under this agreement, disclaim all
    liability to you for damages, costs and expenses, including legal
    fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
    LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
    PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
    TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
    LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
    INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
    DAMAGE.
    
    1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
    defect in this electronic work within 90 days of receiving it, you can
    receive a refund of the money (if any) you paid for it by sending a
    written explanation to the person you received the work from. If you
    received the work on a physical medium, you must return the medium
    with your written explanation. The person or entity that provided you
    with the defective work may elect to provide a replacement copy in
    lieu of a refund. If you received the work electronically, the person
    or entity providing it to you may choose to give you a second
    opportunity to receive the work electronically in lieu of a refund. If
    the second copy is also defective, you may demand a refund in writing
    without further opportunities to fix the problem.
    
    1.F.4. Except for the limited right of replacement or refund set forth
    in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO
    OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
    LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
    
    1.F.5. Some states do not allow disclaimers of certain implied
    warranties or the exclusion or limitation of certain types of
    damages. If any disclaimer or limitation set forth in this agreement
    violates the law of the state applicable to this agreement, the
    agreement shall be interpreted to make the maximum disclaimer or
    limitation permitted by the applicable state law. The invalidity or
    unenforceability of any provision of this agreement shall not void the
    remaining provisions.
    
    1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
    trademark owner, any agent or employee of the Foundation, anyone
    providing copies of Project Gutenberg™ electronic works in
    accordance with this agreement, and any volunteers associated with the
    production, promotion and distribution of Project Gutenberg™
    electronic works, harmless from all liability, costs and expenses,
    including legal fees, that arise directly or indirectly from any of
    the following which you do or cause to occur: (a) distribution of this
    or any Project Gutenberg work, (b) alteration, modification, or
    additions or deletions to any Project Gutenberg work, and (c) any
    Defect you cause.
    
    Section 2. Information about the Mission of Project Gutenberg
    
    Project Gutenberg is synonymous with the free distribution of
    electronic works in formats readable by the widest variety of
    computers including obsolete, old, middle-aged and new computers. It
    exists because of the efforts of hundreds of volunteers and donations
    from people in all walks of life.
    
    Volunteers and financial support to provide volunteers with the
    assistance they need are critical to reaching Project Gutenberg’s
    goals and ensuring that the Project Gutenberg collection will
    remain freely available for generations to come. In 2001, the Project
    Gutenberg Literary Archive Foundation was created to provide a secure
    and permanent future for Project Gutenberg and future
    generations. To learn more about the Project Gutenberg Literary
    Archive Foundation and how your efforts and donations can help, see
    Sections 3 and 4 and the Foundation information page at www.gutenberg.org.
    
    Section 3. Information about the Project Gutenberg Literary Archive Foundation
    
    The Project Gutenberg Literary Archive Foundation is a non-profit
    501(c)(3) educational corporation organized under the laws of the
    state of Mississippi and granted tax exempt status by the Internal
    Revenue Service. The Foundation’s EIN or federal tax identification
    number is 64-6221541. Contributions to the Project Gutenberg Literary
    Archive Foundation are tax deductible to the full extent permitted by
    U.S. federal laws and your state’s laws.
    
    The Foundation’s business office is located at 41 Watchung Plaza #516,
    Montclair NJ 07042, USA, +1 (862) 621-9288. Email contact links and up
    to date contact information can be found at the Foundation’s website
    and official page at www.gutenberg.org/contact
    
    Section 4. Information about Donations to the Project Gutenberg
    Literary Archive Foundation
    
    Project Gutenberg™ depends upon and cannot survive without widespread
    public support and donations to carry out its mission of
    increasing the number of public domain and licensed works that can be
    freely distributed in machine-readable form accessible by the widest
    array of equipment including outdated equipment. Many small donations
    ($1 to $5,000) are particularly important to maintaining tax exempt
    status with the IRS.
    
    The Foundation is committed to complying with the laws regulating
    charities and charitable donations in all 50 states of the United
    States. Compliance requirements are not uniform and it takes a
    considerable effort, much paperwork and many fees to meet and keep up
    with these requirements. We do not solicit donations in locations
    where we have not received written confirmation of compliance. To SEND
    DONATIONS or determine the status of compliance for any particular state
    visit www.gutenberg.org/donate.
    
    While we cannot and do not solicit contributions from states where we
    have not met the solicitation requirements, we know of no prohibition
    against accepting unsolicited donations from donors in such states who
    approach us with offers to donate.
    
    International donations are gratefully accepted, but we cannot make
    any statements concerning tax treatment of donations received from
    outside the United States. U.S. laws alone swamp our small staff.
    
    Please check the Project Gutenberg web pages for current donation
    methods and addresses. Donations are accepted in a number of other
    ways including checks, online payments and credit card donations. To
    donate, please visit: www.gutenberg.org/donate.
    
    Section 5. General Information About Project Gutenberg electronic works
    
    Professor Michael S. Hart was the originator of the Project
    Gutenberg concept of a library of electronic works that could be
    freely shared with anyone. For forty years, he produced and
    distributed Project Gutenberg eBooks with only a loose network of
    volunteer support.
    
    Project Gutenberg eBooks are often created from several printed
    editions, all of which are confirmed as not protected by copyright in
    the U.S. unless a copyright notice is included. Thus, we do not
    necessarily keep eBooks in compliance with any particular paper
    edition.
    
    Most people start at our website which has the main PG search
    facility: www.gutenberg.org.
    
    This website includes information about Project Gutenberg,
    including how to make donations to the Project Gutenberg Literary
    Archive Foundation, how to help produce our new eBooks, and how to
    subscribe to our email newsletter to hear about new eBooks.

    Source: Project Gutenberg ebook #18747. Public-domain status is recorded per item; the licence text above is reproduced unchanged.

    Source
    Project Gutenberg
    Record
    ebook 18747
    Rights
    public domain (US)
    Rendered
    2026-11-22
    Completeness
    Complete held text.