Transactions of the American Society of Civil Engineers, vol. LXX, Dec. 1910
by Herbert M. Wilson · English · Gutenberg #18448 · 323,511 chars · public domain (US)
The Project Gutenberg eBook of Transactions of the American Society of Civil Engineers, vol. LXX, Dec. 1910
This eBook is for the use of anyone anywhere in the United States and
most other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg License included with this eBook or online
at www.gutenberg.org. If you are not located in the United States,
you will have to check the laws of the country where you are located
before using this eBook.
Title: Transactions of the American Society of Civil Engineers, vol. LXX, Dec. 1910
Author: Herbert M. Wilson
Release date: May 25, 2006 [eBook #18448]
Language: English
Other information and formats: www.gutenberg.org/ebooks/18448
Credits: Produced by Louise Hope, Juliet Sutherland and the Online
Distributed Proofreading Team at http://www.pgdp.net
*** START OF THE PROJECT GUTENBERG EBOOK TRANSACTIONS OF THE AMERICAN SOCIETY OF CIVIL ENGINEERS, VOL. LXX, DEC. 1910 ***
Produced by Louise Hope, Juliet Sutherland and the Online
Distributed Proofreading Team at http://www.pgdp.net
[Transcriber’s Note:
All footnotes are grouped at the end of the file. Those that include
non-bibliographic information are _also_ shown after their referring
paragraph.
This UTF-8 file includes a few less common fractions such as ⅛ and ⅔.
Readers who cannot see these characters may prefer the Latin-1 version
of the file.]
* * * * *
AMERICAN SOCIETY OF CIVIL ENGINEERS
Instituted 1852
TRANSACTIONS
Paper No. 1171
FEDERAL INVESTIGATIONS OF MINE ACCIDENTS,
STRUCTURAL MATERIALS, AND FUELS.[1]
By HERBERT M. WILSON, M. Am. Soc. C. E.
With Discussion by Messrs. KENNETH ALLEN,
HENRY KREISINGER, WALTER O. SNELLING,
A. BARTOCCINI, H. G. STOTT, B. W. DUNN,
and HERBERT M. WILSON.
INTRODUCTION.
The mine disaster, which occurred at Cherry, Ill., on November 13th,
1909, when 527 men were in the mine, resulting in the entombment of 330
men, of whom 310 were killed, has again focused public attention on the
frequent recurrence of such disasters and their appalling consequences.
Interest in the possible prevention of such disasters, and the possible
means of combating subsequent mine fires and rescuing the imprisoned
miners, has been heightened as it was not even by the series of three
equally extensive disasters which occurred in 1907, for the reason that,
after the Cherry disaster, 20 men were rescued alive after an entombment
of one week, when practically all hope of rescuing any of the miners had
been abandoned.
This accident, occurring, as it does, a little more than 1½ years after
the enactment of legislation by Congress instructing the Director of the
United States Geological Survey to investigate the causes and possible
means of preventing the loss of life in coal-mining operations, makes
this an opportune time to review what has been done by the Geological
Survey during this time, toward carrying out the intent of this Act.
It may be stated with confidence, that had such a disaster occurred a
year or more ago, all the entombed men must have perished, as it would
have been impossible to enter the mine without the protection afforded
by artificial respiratory apparatus. Moreover, but for the presence of
the skilled corps of Government engineers, experienced by more than a
year’s training in similar operations in more than twenty disasters, the
mine would have been sealed until the fire had burned out, and neither
the dead, nor those who were found alive, would have been recovered for
many weeks. In the interval great suffering and loss would have been
inflicted on the miners, because of enforced idleness, and on the mine
owners because of continued inability to re-open and resume operations.
_Character of the Work._--The United States Geological Survey has been
engaged continuously since 1904 in conducting investigations relating to
structural materials, such as stone, clay, cement, etc., and in making
tests and analyses of the coals, lignites, and other mineral fuel
substances, belonging to, and for the use of, the Government.
Incidentally, the Survey has been considering means to increase
efficiency in the use of these resources as fuels and structural
materials, in the hope that the investigations will lead to their best
utilization.
These inquiries attracted attention to the waste of human life incident
to the mining of fuel and its preparation for the market, with the
result that, in May, 1908, provision was made by Congress for
investigations into the causes of mine explosions with a view to their
prevention.
Statistics collected by the Geological Survey show that the average
death rate in the coal mines of the United States from accidents of all
kinds, including gas and dust explosions, falls of roof, powder
explosions, etc., is three times that of France, Belgium, or Germany. On
the other hand, in no country in the world are natural conditions so
favorable for the safe extraction of coal as in the United States. In
Belgium, foremost in the study of mining conditions, a constant
reduction in the death rate has been secured, and from a rate once
nearly as great as that of the United States, namely, 3.28 per thousand,
in the period 1851-60, it had been reduced to about 2 per thousand in
the period 1881-90; and in the last decade this has been further reduced
to nearly 1 per thousand. It seems certain, from the investigations
already made by the Geological Survey, that better means of safeguarding
the lives of miners will be found, and that the death rate from mine
accidents will soon show a marked reduction.
Other statistics collected by the Geological Survey show that, to the
close of 1907, nearly 7,000,000,000 tons of coal had been mined in the
United States, and it is estimated that for every ton mined nearly a ton
has been wasted, 3,500,000,000 tons being left in the ground or thrown
on the dump as of a grade too low for commercial use. To the close of
1907 the production represents an exhaustion of somewhat more than
10,000,000,000 tons of coal. It has been estimated that if the
production continues to increase, from the present annual output of
approximately 415,000,000 tons, at the rate which has prevailed during
the last fifty years, the greater part of the more accessible coal
supply will be exhausted before the middle of the next century.
The Forest Service estimates that, at the present rate of consumption,
renewals of growth not being taken into account, the timber supply will
be exhausted within the next quarter of a century. It is desirable,
therefore, that all information possible be gained regarding the most
suitable substitutes for wood for building and engineering construction,
such as iron, stone, clay products, concrete, etc., and that the minimum
proportion in which these materials should be used for a given purpose,
be ascertained. Exhaustion, by use in engineering and building
construction, applies not only to the iron ore, clay, and cement-making
materials, but, in larger ratio, to the fuel essential to rendering
these substances available for materials of construction. Incidentally,
investigations into the waste of structural materials have developed the
fact that the destructive losses, due to fires in combustible buildings,
amount to more than $200,000,000 per annum. A sum even greater than this
is annually expended on fire protection. Inquiries looking to the
reduction of fire losses are being conducted in order to ascertain the
most suitable fire-resisting materials for building construction.
Early in 1904, during the Louisiana Purchase Exposition, Congress made
provision for tests, demonstrations, and investigations concerning the
fuels and structural materials of the United States. These
investigations were organized subsequently as the Technologic Branch of
the United States Geological Survey, under Mr. Joseph A. Holmes, Expert
in Charge, and the President of the United States invited a group of
civilian engineers and Chiefs of Engineering Bureaus of the Government
to act as a National Advisory Board concerning the method of conducting
this work, with a view to making it of more immediate benefit to the
Government and to the people of the United States. This Society is
formally represented on this Board by C. C. Schneider, Past-President,
Am. Soc. C. E., and George S. Webster, M. Am. Soc. C. E. Among
representatives of other engineering societies, or of Government
Bureaus, the membership of the National Advisory Board includes other
members of this Society, as follows: General William Crozier, Frank T.
Chambers, Professor W. K. Hatt, Richard L. Humphrey, Robert W. Hunt, H.
G. Kelley, Robert W. Lesley, John B. Lober, Hunter McDonald, and
Frederick H. Newell.
In view, therefore, of the important part taken both officially and
unofficially by members of this Society in the planning and organization
of this work, it seems proper to present a statement of the scope,
methods, and progress of these investigations. Whereas the Act governing
this work limits the testing and investigation of fuels and of
structural materials to those belonging to the United States, the
activities of the Federal Government in the use of these materials so
far exceeds that of any other single concern in the United States, that
the results cannot but be of great value to all engineers and to all
those engaged in engineering works.
MINE ACCIDENTS INVESTIGATIONS.
_Organization, and Character of the Work._--The mine rescue
investigations, carried on at the Federal testing station, at Pittsburg,
Pa., include five lines of attack:
1.--Investigations in the mines to determine the conditions leading up
to mine disasters, the presence and the relative explosibility of mine
gas and coal dust, and mine fires and means of preventing and combating
them.
2.--Tests to determine the relative safety, or otherwise, of the various
explosives used in coal mining, when ignited in the presence of
explosible mixtures of natural gas and air, or coal dust, or of both.
3.--Tests to determine the conditions under which electric equipment is
safe in coal-mining operations.
4.--Tests to determine the safety of various types of mine lights in the
presence of inflammable gas, and their accuracy in detecting small
percentages of mine gas.
5.--Tests of the various artificial breathing apparatus, and the
training of miners and of skilled mining engineers in rescue methods.
The first four of these lines of investigation have to do with
preventive measures, and are those on which ultimately the greatest
dependence must be placed. The fifth is one in which the result seems at
first to be the most apparent. It has to do, not with prevention, but
with the cure of conditions which should not arise, or, at least, should
be greatly ameliorated.
During the last 19 years, 28,514 men have been killed in the coal-mining
industries.[2] In 1907 alone, 3,125 men lost their lives in coal mines,
and, in addition, nearly 800 were killed in the metal mines and quarries
of the country. Including the injured, 8,441 men suffered casualties in
the mines in that year. In every mining camp containing 1,000 men, 4.86
were taken by violent death in that year. In the mining of coal in Great
Britain, 1.31 men were killed in every 1,000 employed in the same year;
in France, 1.1; in Belgium, 0.94, or less than 1 man in every 1,000
employed. It is thus seen that from three to four times as many men are
being killed in the United States as in any European coal-producing
country. This safer condition in Europe has resulted from the use of
safer explosives, or the better use of the explosives available; from
the reduction in the use of open lights; from the establishment of mine
rescue stations and the training with artificial breathing apparatus;
and from the adoption of regulations for safeguarding the lives of the
workmen.
The mining engineering field force of the Geological Survey, at the head
of which is Mr. George S. Rice, an experienced mining and consulting
engineer, has already made great progress in the study of underground
mining conditions and methods. Nearly all the more dangerous coal mines
in the United States have been examined; samples of gas, coal, and dust
have been taken and analyzed at the chemical laboratories at Pittsburg;
extended tests have been made as to the explosibility of various
mixtures of gas and air; as to the explosibility of dust from various
typical coals; as to the chemical composition and physical
characteristics of this dust; the degree of fineness necessary to the
most explosive conditions; and the methods of dampening the dust by
water, by humidifying, by steam, or of deadening its explosibility by
the addition of calcium chloride, stone dust, etc. A bulletin outlining
the results thus far obtained in the study of the coal-dust problem is
now in course of publication.[3]
After reviewing the history of observations and experiments with coal
dust carried on in Europe, and later, the experiments at the French,
German, Belgian, and English explosives-testing stations, this bulletin
takes up the coal-dust question in the United States. Further chapters
concern the tests as to the explosibility of coal dust, made by the
Geological Survey, at Pittsburg; investigations, both at the Pittsburg
laboratory and in mines, as to the humidity of mine air. There is also a
chapter on the chemical investigations into the ignition of coal dust by
Dr. J. C. W. Frazer, of the Geological Survey. The application of some
of these data to actual mine conditions in Europe, in the last year, is
treated by Mr. Axel Larsen; the use of exhaust steam in a mine of the
Consolidation Coal Company, in West Virginia, is discussed by Mr. Frank
Haas, Consulting Engineer; and the use of sprays in Oklahoma coal mines
is the subject of a chapter by Mr. Carl Scholz, Vice-President of the
Rock Island Coal Mining Company.
An earlier bulletin setting forth the literature and certain mine
investigations of explosive gases and dust,[4] has already been issued.
After treating of methods of collecting and analyzing the gases found in
mines, of investigations as to the rate of liberation of gas from coal,
and of studies on coal dust, this bulletin discusses such factors as the
restraining influence of shale dust and dampness on coal-dust
explosions. It then takes up practical considerations as to the danger
of explosions, including the relative inflammability of old and fresh
coal dust. The problems involved are undergoing further investigation
and elaboration, in the light of information already gathered.
_Permissible Explosives._--The most important progress in these tests
and investigations has been made in those relating to the various
explosives used in getting coal from mines. Immediately upon the
enactment of the first legislation, in the spring of 1908, arrangements
were perfected whereby the lower portion of the old Arsenal grounds
belonging to the War Department and adjacent to the Pennsylvania
Railroad, on the Alleghany River, at 40th and Butler Streets, Pittsburg,
Pa., were transferred to the Interior Department for use in these
investigations. Meantime, in anticipation of the appropriation, Mr.
Clarence Hall, an engineer experienced in the manufacture and use of
explosives, was sent to Europe to study the methods of testing
explosives practiced at the Government stations in Great Britain,
Germany, Belgium, and France. Mr. Joseph A. Holmes also visited Europe
for the purpose of studying methods of ameliorating conditions in the
mines. Three foreign mining experts, the chiefs of investigating bureaus
in Belgium, Germany, and England, spent three months studying conditions
in the United States at the invitation of the Secretary of the Interior,
to whom they submitted a valuable report.[5]
Under the supervision of the writer, Chief Engineer of these
investigations, detailed plans and specifications had been prepared in
advance for the necessary apparatus and the transformation of the
buildings at Pittsburg to the purposes of this work. It was possible,
therefore, to undertake immediately the changes in existing buildings,
the erection of new buildings, the installation of railway tracks,
laboratories, and the plumbing, heating, and lighting plant, etc. This
work was carried on with unusual expedition, under the direction of the
Assistant Chief Engineer, Mr. James C. Roberts, and was completed within
a few months, by which time most of the apparatus was delivered and
installed.
One building (No. 17) is devoted to the smaller physical tests of
explosives. It was rendered fire resistant by heavily covering the
floors, ceiling, and walls with cement on metal lath, and otherwise
protecting the openings. In it are installed apparatus for determining
calorific value of explosives, pressure produced on ignition,
susceptibility to ignition when dropped, rate of detonation, length and
duration of flame, and kindred factors. Elsewhere on the grounds is a
gallery of boiler-steel plate, 100 ft. long and more than 6 ft. in
diameter, solidly attached to a mass of concrete at one end, in which is
embedded a cannon from which to discharge the explosive under test, and
open at the other end, and otherwise so constructed as to simulate a
small section of a mine gallery (Fig. 2, Plate VI). The heavy mortar
pendulum, for the pendulum test for determining the force produced by an
explosive, is near by, as is also an armored pit in which large
quantities of explosive may be detonated, with a view to studying the
effects of magazine explosions, and for testing as to the rate at which
ignition of an explosive travels from one end to the other of a
cartridge, and the sensitiveness of one cartridge to explosion by
discharge of another near by.
[Illustration: PLATE VI.
Fig. 1.--Explosion from Coal Dust in Gas and Dust Gallery No. 1.
Fig. 2.--Mine Gallery No. 1.
Fig. 3.--Ballistic Pendulum.]
In another building (No. 21), is a well-equipped chemical laboratory for
chemical analyses and investigations of explosives, structural
materials, and fuels.
Several months were required to calibrate the various apparatus, and to
make analyses of the available natural gas to determine the correct
method of proportioning it with air, so as to produce exact mixtures of
2, 4, 6, or 8% of methane with air. Tests of existing explosives were
made in air and in inflammable mixtures of air and gas, with a view to
fixing on some standard explosive as a basis of comparison. Ultimately,
40% nitro-glycerine dynamite was adopted as the standard. Investigative
tests having been made, and the various factors concerning all the
explosives on the market having been determined, a circular was sent to
all manufacturers of explosives in the United States, on January 9th,
1909, and was also published in the various technical journals, through
the associated press, and otherwise.
On May 15th, 1909, all the explosives which had been offered for test,
as permissible, having been tested, the first list of permissible
explosives was issued, as given in the following circular:
“EXPLOSIVES CIRCULAR NO. 1.
“DEPARTMENT OF THE INTERIOR.
“United States Geological Survey.
“May 15, 1909.
“LIST OF PERMISSIBLE EXPLOSIVES.
“Tested prior to May 15, 1909.
“As a part of the investigation of mine explosions authorized by
Congress in May, 1908, it was decided by the Secretary of the Interior
that a careful examination should be made of the various explosives
used in mining operations, with a view to determining the extent to
which the use of such explosives might be responsible for the
occurrence of these disasters.
“The preliminary investigation showed the necessity of subjecting to
rigid tests all explosives intended for use in mines where either gas
or dry inflammable dust is present in quantity or under conditions
which are indicative of danger.
“With this in view, a letter was sent by the Director of the United
States Geological Survey on January 9, 1909, to the manufacturers of
explosives in the United States, setting forth the conditions under
which these explosives would be examined and the nature of the tests
to which they would be subjected.
“Inasmuch as the conditions and tests described in this letter were
subsequently followed in testing the explosives given in the list
below, they are here reproduced, as follows:
“(1) The manufacturer is to furnish 100 pounds of each explosive which
he desires to have tested; he is to be responsible for the care,
handling, and delivery of this material at the testing station on the
United States arsenal grounds, Fortieth and Butler streets, Pittsburg,
Pa., at the time the explosive is to be tested; and he is to have a
representative present during the tests, who will be responsible for
the handling of the packages containing the explosives until they are
opened for testing.
“(2) No one is to be present at or to participate in these tests
except the necessary government officers at the testing station, their
assistants, and the representative of the manufacturer of the
explosives to be tested.
“(3) The tests will be made in the order of the receipt of the
applications for them, provided the necessary quantity of the
explosive is delivered at the plant by the time assigned, of which due
notice will be given by the Geological Survey.
“(4) Preference will be given to the testing of explosives that are
now being manufactured and that are in that sense already on the
market. No test will be made of any new explosive which is not now
being manufactured and marketed, until all explosives now on the
market that may be offered for testing have been tested.
“(5) A list of the explosives which pass certain requirements
satisfactorily will be furnished to the state mine inspectors, and
will be made public in such further manner as may be considered
desirable.
“TEST REQUIREMENTS FOR EXPLOSIVES.
“The tests will be made by the engineers of the United States
Explosives Testing Station at Pittsburg, Pa., in gas and dust gallery
No. 1. The charge of explosive to be fired in tests 1, 2, and 3 shall
be equal in disruptive power to one-half pound (227 grams) of 40 per
cent. nitroglycerin dynamite in its original wrapper, of the following
formula:
Nitroglycerin 40
Nitrate of sodium 44
Wood pulp 15
Calcium carbonate 1
---
100
“Each charge shall be fired with an electric fuse of sufficient power
to completely detonate or explode the charge, as recommended by the
manufacturer. The explosive must be in such condition that the
chemical and physical tests do not show any unfavorable results. The
explosives in which the charge used is less than 100 grams (0.22
pound) will be weighed in tinfoil without the original wrapper.
“The dust used in tests 2, 3, and 4 will be of the same degree of
fineness and taken from one mine.[6]
[Footnote 6: With a view to obtaining a dust of uniform purity and
inflammability.]
“TEST 1.--Ten shots with the charge as described above, in its
original wrapper, shall be fired, each with 1 pound of clay tamping,
at a gallery temperature of 77° F., into a mixture of gas and air
containing 8 per cent. of methane and ethane. An explosive will pass
this test if all ten shots fail to ignite the mixture.
“TEST 2.--Ten shots with charge as previously noted, in its original
wrapper, shall be fired, each with 1 pound of clay tamping at a
gallery temperature of 77° F., into a mixture of gas and air
containing 4 per cent. of methane and ethane and 20 pounds of
bituminous coal dust, 18 pounds of which is to be placed on shelves
laterally arranged along the first 20 feet of the gallery, and 2
pounds to be placed near the inlet of the mixing system in such a
manner that all or part of it will be suspended in the first division
of the gallery. An explosive will pass this test if all ten shots fail
to ignite the mixture.
“TEST 3.--Ten shots with charge as previously noted, in its original
wrapper, shall be fired, each with 1 pound of clay tamping at a
gallery temperature of 77° F., into 40 pounds of bituminous coal dust,
20 pounds of which is to be distributed uniformly on a horse placed in
front of the cannon and 20 pounds placed on side shelves in sections
4, 5, and 6. An explosive will pass this test if all ten shots fail to
ignite the mixture.
“TEST 4.--A limit charge will be determined within 25 grams by firing
charges in their original wrappers, untamped, at a gallery temperature
of 77° F., into a mixture of gas and air containing 4 per cent. of
methane and ethane and 20 pounds of bituminous coal dust, to be
arranged in the same manner as in test 2. This limit charge is to be
repeated five times under the same conditions before being
established.
“NOTE.--At least 2 pounds of clay tamping will be used with
slow-burning explosives.
“Washington, D.C., _January 9, 1909_.
“In response to the above communication applications were received
from 12 manufacturers for the testing of 29 explosives. Of these
explosives, the 17 given in the following list have passed all the
test requirements set forth, and will be termed permissible
explosives.
“_Permissible explosives tested prior to May 15, 1909._
----------------------------+----------------------------------------
Brand. | Manufacturer.
----------------------------+----------------------------------------
Ætna coal powder A | Ætna Powder Co., Chicago, Ill.
Ætna coal powder B | Do.
Carbonite No. 1 | E. I. Dupont de Nemours Powder Co.,
| Wilmington, Del.
Carbonite No. 2 | E. I. Du Pont de Nemours Powder Co.,
| Wilmington, Del.
Carbonite No. 3 | Do.
Carbonite No. 1 L. F. | Do.
Carbonite No. 2 L. F. | Do.
Coal special No. 1 | Keystone Powder Co., Emporium, Pa.
Coal special No. 2 | Do.
Coalite No. 1 | Potts Powder Co., New York City.
Coalite No. 2 D | Do.
Collier dynamite No. 2 | Sinnamahoning Powder Co., Emporium, Pa.
Collier dynamite No. 4 | Do.
Collier dynamite No. 5 | Do.
Masurite M. L. F. | Masurite Explosive Co., Sharon, Pa.
Meteor dynamite | E. I. Du Pont de Nemours Powder Co.,
| Wilmington, Del.
Monobel | Do.
----------------------------+----------------------------------------
“Subject to the conditions named below, a permissible explosive is
defined as an explosive which has passed gas and dust gallery tests
Nos. 1, 2, and 3 as described above, and of which in test No. 4 1½
pounds (680 grams) of the explosive has been fired into the mixture
there described without causing an ignition.
“_Provided:_
“1. That the explosive is in all respects similar to the sample
submitted by the manufacturer for test.
“2. That double-strength detonators are used of not less strength than
1 gram charge consisting by weight of 90 parts of mercury fulminate
and 10 parts of potassium chlorate (or its equivalent), except for the
explosive ‘Masurite M. L. F.’ for which the detonator shall be of not
less strength than 1½ grams charge.
“3. That the explosive, if in a frozen condition, shall be thoroughly
thawed in a safe and suitable manner before use.
“4. That the amount used in practice does not exceed 1½ pounds (680
grams) properly tamped.
“The above partial list includes the permissible explosives that have
passed these tests prior to May 15, 1909. The announcement of the
passing of like tests by other explosives will be made public
immediately after the completion of the tests for such explosives.
“A description of the method followed in making these and the many
additional tests to which each explosive is subjected, together with
the full data obtained in each case, will be published by the Survey
at an early date.
“NOTES AND SUGGESTIONS.
“It may be wise to point out in this connection certain differences
between the permissible explosives as a class and the black powders
now so generally used in coal mining, as follows:
“(_a_) With equal quantities of each, the flame of the black powder is
more than three times as long and has a duration three thousand to
more than four thousand times that of one of the permissible
explosives, also the rate of explosion is slower.
“(_b_) The permissible explosives are one and one-fourth to one and
three-fourths times as strong and are said, if properly used, to do
twice the work of black powder in bringing down coal; hence only half
the quantity need be used.
“(_c_) With 1 pound of a permissible explosive or 2 pounds of black
powder, the quantity of noxious gases given off from a shot averages
approximately the same, the quantity from the black powder being less
than from some of the permissible explosives and slightly greater than
from others. The time elapsing after firing before the miner returns
to the working face or fires another shot should not be less for
permissible explosives than for black powder.
“The use of permissible explosives should be considered as
supplemental to and not as a substitute for other safety precautions
in mines where gas or inflammable coal dust is present under
conditions indicative of danger. As stated above, they should be used
with strong detonators; and the charge used in practice should not
exceed 1½ pounds, and in many cases need not exceed 1 pound.
“Inasmuch as no explosive manufactured for use in mining is flameless,
and as no such explosive is entirely safe under all the variable
mining conditions, the use of the terms ‘flameless’ and ‘safety’ as
applied to explosives is likely to be misunderstood, may endanger
human life, and should be discouraged.
“JOSEPH A. HOLMES,
“_Expert in Charge Technologic Branch_.
“Approved, May 18, 1909:
“GEO. OTIS SMITH,
“_Director_.”
In the meantime, many of the explosives submitted, which heretofore had
been on the market as safety explosives, were found to be unsafe for
use in gaseous or dusty mines, and the manufacturers were permitted
to withdraw them. Their weaknesses being known, as a result of these
tests, the manufacturers were enabled to produce similar, but safer,
explosives. Consequently, applications for further tests continued
to pour in, as they still do, and on October 1st, 1909, a second list
of permissible explosives was issued, as follows:
“EXPLOSIVES CIRCULAR NO. 2.
“DEPARTMENT OF THE INTERIOR.
“United States Geological Survey.
“October 1, 1909.
“LIST OF PERMISSIBLE EXPLOSIVES.
“Tested prior to October 1, 1909.
“The following list of permissible explosives tested by the United
States Geological Survey at Pittsburg, Pa., is hereby published for
the benefit of operators, mine owners, mine inspectors, miners, and
others interested.
“The conditions and test requirements described in Explosives Circular
No. 1, issued under date of May 15, 1909, have been followed in all
subsequent tests.
“Subject to the provisions named below, a permissible explosive is
defined as an explosive which is in such condition that the chemical
and physical tests do not show any unfavorable results; which has
passed gas and dust gallery tests Nos. 1 and 3, as described in
circular No. 1; and of which, in test No. 4, 1½ pounds (680 grams) has
been fired into the mixture there described without causing ignition.
“_Permissible explosives tested prior to October 1, 1909._
“[Those reported in Explosives Circular No. 1 are marked *.]
------------------------------+-------------------------------------
Brand. | Manufacturer.
------------------------------+-------------------------------------
*Ætna coal powder A | Ætna Powder Co., Chicago, Ill.
Ætna coal powder AA | Do.
*Ætna coal powder B | Do.
Ætna coal powder C | Do.
Bituminite No. 1 | Jefferson Powder Co., Birmingham,
| Ala.
Black Diamond No. 3 | Illinois Powder Manufacturing Co.,
| St. Louis, Mo.
Black Diamond No. 4 | Do.
*Carbonite No. 1 | E. I. Du Pont de Nemours Powder Co.,
| Wilmington, Del.
*Carbonite No. 2 | Do.
*Carbonite No. 3 | Do.
*Carbonite No. 1-L. F. | Do.
*Carbonite No. 2-L. F. | Do.
*Coalite No. 1 | Potts Powder Co., New York City.
*Coalite No. 2-D. | Do.
*Coal special No. 1 | Keystone Powder Co., Emporium, Pa.
*Coal special No. 2 | Do.
*Collier dynamite No. 2. | Sinnamahoning Powder Manufacturing
| Co., Emporium, Pa.
*Collier dynamite No. 4. | Do.
*Collier dynamite No. 5. | Do.
Giant A low-flame dynamite. | Giant Powder Co. (Con.), Giant, Cal.
Giant B low-flame dynamite. | Do.
Giant C low-flame dynamite. | Do.
*Masurite M. L. F. | Masurite Explosives Co., Sharon, Pa.
*Meteor dynamite. | E. I. Du Pont de Nemours Powder Co.,
| Wilmington, Del.
Mine-ite A. | Burton Powder Co., Pittsburg, Pa.
Mine-ite B. | Do.
*Monobel. | E. I. Du Pont de Nemours Powder Co.,
| Wilmington, Del.
Tunnelite No. 5. | G. R. McAbee Powder and Oil Co.,
| Pittsburg, Pa.
Tunnelite No. 6. | Do.
Tunnelite No. 7. | Do.
Tunnelite No. 8. | Do.
------------------------------+-------------------------------------
“_Provided:_
“1. That the explosive is in all respects similar to sample submitted
by the manufacturer for test.
“2. That No. 6 detonators, preferably No. 6 electric detonators
(double strength), are used of not less strength than 1 gram charge,
consisting by weight of 90 parts of mercury fulminate and 10 parts of
potassium chlorate (or its equivalent), except for the explosive
’Masurite M. L. F.,’ for which the detonator shall be of not less
strength than 1½ grams charge.
“3. That the explosive, if frozen, shall be thoroughly thawed in a
safe and suitable manner before use.
“4. That the amount used in practice does not exceed 1½ pounds (680
grams), properly tamped.
“The above partial list includes all the permissible explosives that
have passed these tests prior to October 1, 1909. The announcement of
the passing of like tests by other explosives will be made public
immediately after the completion of the tests.
“With a view to the wise use of these explosives it may be well in
this connection to point out again certain differences between the
permissible explosives as a class and the black powders now so
generally used in coal mining, as follows:
“(_a_) With equal quantities of each, the flame of the black powder is
more than three times as long and has a duration three thousand to
more than four thousand times that of one of the permissible
explosives; the rate of explosion also is slower.
“(_b_) The permissible explosives are one and one-fourth to one and
three-fourths times as strong and are said, if properly used, to do
twice the work of black powder in bringing down coal; hence only half
the quantity need be used.
“(_c_) With 1 pound of a permissible explosive or 2 pounds of black
powder, the quantity of noxious gases given off from a shot averages
approximately the same, the quantity from the black powder being less
than from some of the permissible explosives and slightly greater than
from others. The time elapsing after firing before the miner returns
to the working face or fires another shot should not be less for
permissible explosives than for black powder.
“The use of permissible explosives should be considered as
supplemental to and not as a substitute for other safety precautions
in mines where gas or inflammable coal dust is present under
conditions indicating danger. As stated above, they should be used
with strong detonators, and the charge used in practice should not
exceed 1½ pounds and in many cases need not exceed 1 pound.
“JOSEPH A. HOLMES,
“_Expert in Charge Technologic Branch._
“Approved, October 11, 1909.
“H. C. RIZER,
“_Acting Director._”
The second list contains 31 explosives which the Government is prepared
to brand as permissible, and therefore comparatively safe, for use in
gaseous and dusty mines. An equally large number of so-called safety
powders failed to pass these tests. Immediately on the passing of the
tests, as to the permissibility of any explosive, the facts are reported
to the manufacturer and to the various State mine inspectors. When
published, the permissible lists were issued to all explosives
manufacturers, all mine operators in the United States, and State
inspectors. The effect has been the enactment, by three of the largest
coal-producing States, of legislation or regulations prohibiting the use
of any but permissible explosives in gaseous or dusty mines, and other
States must soon follow. To prevent fraud, endeavor is being made to
restrict the use of the brand “Permissible Explosive, U.S. Testing
Station, Pittsburg, Pa.,” to only such boxes or packages as contain
listed permissible explosives.
As these tests clearly demonstrate, both in the records thereof and
visually to such as follow them, that certain explosives, especially
those which are slow-burning like black powder, or produce high
temperature in connection with comparative slow burning, will ignite
mixtures of gas and air, or mixtures of coal dust and air, and cause
explosions. The results point out clearly to all concerned, the danger
of using such explosives. The remedy is also made available by the
announcement of the names of a large number of explosives now on the
market at reasonable cost, which will not cause explosions under these
conditions. It is believed that when permissible explosives are
generally adopted in coal mines, this source of danger will have been
greatly minimized.
_Explosives Investigations._--Questions have arisen on the part of
miners or of mine operators as to the greater cost in using permissible
explosives due to their expense, which is slightly in excess of that of
other explosives; as to their greater shattering effect in breaking down
the coal, and in giving a smaller percentage of lump and a larger
percentage of slack; and as to the possible danger of breathing the
gases produced.
Observations made in mines by Mr. J. J. Rutledge, an experienced coal
miner and careful mining engineer connected with the Geological Survey,
as to the amount of coal obtained by the use of permissible and other
explosives, tend to indicate that the permissible explosives are not
more, but perhaps less expensive than others, in view of the fact that,
because of their greater relative power, a smaller quantity is required
to do the work than is the case, say, with black powder. On the other
hand, for safety and for certainty of detonation, stronger detonators
are recommended for use with permissible explosives, preferably electric
detonators. These may cost a few cents more per blast than the squib or
fuse, but there is no danger that they will ignite the gas, and the
difference in cost is, in some measure, offset by the greater certainty
of action and the fact that they produce a much more powerful explosion,
thus again permitting the use of still smaller quantities of the
explosive and, consequently, reducing the cost. These investigations are
still in progress.
Concerning the shattering of the coal: This is being remedied in some of
the permissible explosives by the introduction of dopes, moisture, or
other means of slowing down the disruptive effect, so as to produce the
heaving and breaking effect obtained with the slower-burning powders
instead of the shattering effect produced by dynamite. There is every
reason to believe that as the permissible explosives are perfected, and
as experience develops the proper methods of using them, this difficulty
will be overcome in large measure. This matter is also being
investigated by the Survey mining engineers and others, by the actual
use of such explosives in coal-mining operations.
Of the gases given off by explosives, those resulting from black powder
are accompanied by considerable odor and smoke, and, consequently, the
miners go back more slowly after the shots, allowing time for the gases
to be dissipated by the ventilation. With the permissible explosive, the
miner, seeing no smoke and observing little odor, is apt to be
incautious, and to think that he may run back immediately. As more is
learned of the use of these explosives, this source of danger, which is,
however, inconsiderable, will be diminished. Table 1 gives the
percentages of the gaseous products of combustions from equal weights of
black powder and two of the permissible explosives. Of the latter, one
represents the maximum amount of injurious gases, and the other the
minimum amount, between which limits the permissible explosives
approximately vary.
Such noxious gases as may be produced by the discharge of the explosive
are diluted by a much larger volume of air, and are practically
harmless, as proven by actual analysis of samples taken at the face
immediately after a discharge.
TABLE 1.
--------+---------+--------------------------
| | Permissible Explosives.
| Black |-------------+------------
| powder. | Maximum. | Minimum.
--------+---------+-------------+------------
CO_{2} | 22.8 | 14.50 | 21.4
CO | 10.3 | 27.74 | 1.3
N | 10.3 | 45.09 | 74.4
--------+---------+-------------+------------
In addition to investigations as to explosives for use in coal mining,
the Explosives Section of the Geological Survey analyzes and tests all
such materials, fuses, caps, etc., purchased by the Isthmian Canal
Commission, as well as many other kinds used by the Government. It is
thus acquiring a large fund of useful information, which will be
published from time to time, relative to the kinds of explosives and the
manner of using them best suited to any blasting operations, either
above or under water, in hard rock, earth, or coal. There has been
issued from the press, recently, a primer of explosives,[7] by Mr.
Clarence Hall, the engineer in charge of these tests, and Professor C.
E. Munroe, Consulting Explosives Chemist, which contains a large amount
of valuable fundamental information, so simply expressed as to be easily
understandable by coal miners, and yet sufficiently detailed to be a
valuable guide to all persons who have to handle or use explosives.
In the first chapters are described the various combustible substances,
and the chemical reactions leading to their explosibility. The low and
high explosives are differentiated, and the sensitiveness of fulminate
of mercury and other detonators is clearly pointed out. The various
explosives, such as gunpowder, black blasting powder, potassium chlorate
powders, nitro-glycerine powders, etc., are described, and their
peculiarities and suitability for different purposes are set forth. The
character and method of using the different explosives, both in opening
up work and in enclosed work in coal mines, follow, with information as
to the proper method of handling, transporting, storing, and thawing the
same. Then follow chapters on squibs, fuses, and detonators; on methods
of shooting coal off the solid; location of bore-holes; undercutting;
and the relative advantages of small and large charges, with
descriptions of proper methods of loading and firing the same. The
subjects of explosives for blasting in rock, firing machines, blasting
machines, and tests thereof, conclude the report.
The work of the chemical laboratory in which explosives are analyzed,
and in which mine gases and the gases produced by combustion of
explosives and explosions of coal-gas or coal dust are studied, has been
of the most fundamental and important character. The Government is
procuring a confidential record of the chemical composition and mode of
manufacture of all explosives, fuses, etc., which are on the market.
This information cannot but add greatly to the knowledge as to the
chemistry of explosives for use in mines, and will furnish the basis on
which remedial measures may be devised.
A bulletin (shortly to go to press) which gives the details of the
physical tests of the permissible explosives thus far tested, will set
forth elaborately the character of the testing apparatus, and the method
of use and of computing results.[8]
This bulletin contains a chapter, by Mr. Rutledge, setting forth in
detail the results of his observations as to the best methods of using
permissible explosives in getting coal from various mines in which they
are used. This information will be most valuable in guiding mining
engineers who desire to adopt the use of permissible explosives, as to
the best methods of handling them.
_Electricity in Mines._--In connection with the use of electricity in
mines, an informal series of tests has been made on all enclosed
electric fuses, as to whether or not they will ignite an explosive
mixture of air and gas when blown out. The results of this work, which
is under the direction of Mr. H. H. Clark, Electrical Engineer for
Mines, have been furnished the manufacturers for their guidance in
perfecting safer fuses, a series of tests of which has been announced. A
series of tests as to the ability of the insulation of electric wiring
to withstand the attacks of acid mine waters is in progress, which will
lead, it is hoped, to the development of more permanent and cheaper
insulation for use in mine wiring. A series of competitive tests of
enclosed motors for use in mines has been announced, and is in progress,
the object being to determine whether or not sparking from such motors
will cause an explosion in the presence of inflammable gas.
In the grounds outside of Building No. 10 is a large steel gallery, much
shorter than Gallery No. 1, in fact, but 30 ft. in length, and much
greater in diameter, namely, 10 ft. (Fig. 3, Plate X), in which electric
motors, electric cutting machines, and similar apparatus, are being
tested in the presence of explosive mixtures of gas and dust and with
large amperage and high voltage, such as may be used in the largest
electrical equipment in mines.
The investigation as to the ability of insulation to withstand the
effects of acid mine waters has been very difficult and complicated. At
first it was believed possible that mine waters from nearby Pennsylvania
mines and of known percentages of acidity could be procured and kept in
an immersion tank at approximately any given percentage of strength.
This was found to be impracticable, as these waters seem to undergo
rapid change the moment they are exposed to the air or are transported,
in addition to the changes wrought by evaporation in the tank. It has
been necessary, therefore, to analyze and study carefully these waters
with a view to reproducing them artificially for the purpose of these
tests. Concerning the insulation, delicate questions have arisen as to a
standard of durability which shall be commensurate with reasonable cost.
These preliminary points are being solved in conference with the
manufacturers, and it is expected that the results will soon permit of
starting the actual tests.
_Safety-Lamp Investigations._--Many so-called safety lamps are on the
market, and preliminary tests of them have been made in the lamp
gallery, in Building No. 17 (Fig. 2, Plate X). After nearly a year of
endeavor to calibrate this gallery, and to co-ordinate its results with
those produced in similar galleries in Europe, this preliminary inquiry
has been completed, and the manufacturers and agents of all safety lamps
have been invited to be present at tests of their products at the
Pittsburg laboratory.
A circular dated November 19th, 1909, contains an outline of these
tests, which are to be conducted under the direction of Mr. J. W. Paul,
an experienced coal-mining engineer and ex-Chief of the Department of
State Mine Inspection of West Virginia. The lamps will be subjected to
the following tests:
(_a_).--Each lamp will be placed in a mixture of air and explosive
natural gas containing 6, 8, and 10% of gas, moving at a velocity of
from 200 to 2,500 ft. per min., to determine the velocity of the air
current which will ignite the mixture surrounding the lamp. The current
will be made to move against the lamp in a horizontal, vertical
ascending, and vertical descending direction, and at an angle of 45°,
ascending and descending.
(_b_).--After completing the tests herein described, the lamps will be
subjected to the tests described under (_a_), with the air and gas
mixture under pressure up to 6 in. of water column.
(_c_).--Under the conditions outlined in (_a_), coal dust will be
introduced into the current of air and gas to determine its effect, if
any, in inducing the ignition of the gas mixture.
(_d_).--Each lamp will be placed in a mixture of air and varying
percentages of explosive natural gas to determine the action of the gas
on the flame of the lamp.
(_e_).--Each lamp will be placed in a mixture of air and varying
percentages of carbonic acid gas to determine the action of the gas on
the flame.
(_f_).--Lamps equipped with internal igniters will be placed in
explosive mixtures of air and gas in a quiet state and in a moving
current, and the effect of the igniter on the surrounding mixture will
be observed.
(_g_).--The oils (illuminants) used in the lamps will be tested as to
viscosity, gravity, flashing point, congealing point, and composition.
(_h_).--Safety-lamp globes will be tested by placing each globe in
position in the lamp and allowing the flame to impinge against the globe
for 3 min. after the lamp has been burning with a full flame for 10
min., to determine whether the globe will break.
(_i_).--Each safety-lamp globe will be mounted in a lighted lamp with
up-feed, and placed for 5 min. in an explosive mixture of air and gas
moving at the rate of 1,000 ft. per min., to determine whether the heat
will break the glass and, if it is broken, to note the character of the
fracture.
(_j_).--Safety-lamp globes will be broken by impact, by allowing each
globe to fall and strike, horizontally, on a block of seasoned white
oak, the distance of fall being recorded.
(_k_).--Each safety lamp globe will be mounted in a safety lamp and,
when the lamp is in a horizontal position, a steel pick weighing 100
grammes will be permitted to fall a sufficient distance to break the
globe by striking its center, the distance of the fall to be recorded.
(_l_).--To determine the candle power of safety lamps, a photometer
equipped with a standardized lamp will be used. The candle-power will be
determined along a line at right angles to the axis of the flame; also
along lines at angles to the axis of the flame both above and below the
horizontal. The candle-power will be read after the lamp has been
burning 20 min.
(_m_).--The time a safety lamp will continue to burn with a full charge
of illuminant will be determined.
(_n_).--Wicks in lamps must be of sufficient length to be at all times
in contact with the bottom of the vessel in which the illuminant is
contained, and, before it is used, the wick shall be dried to remove
moisture.
_Mine-Rescue Methods._--Mr. Paul, who has had perhaps as wide an
experience as any mining man in the investigation of and in rescue work
at mine disasters, is also in charge of the mine-rescue apparatus and
training for the Geological Survey. These operations consist chiefly of
a thorough test of the various artificial breathing apparatus, or
so-called oxygen helmets. Most of these are of European make and find
favor in Great Britain, Belgium, France, or Germany, largely according
as they are of domestic design and manufacture. As yet nothing has been
produced in the United States which fulfills all the requirements of a
thoroughly efficient and safe breathing apparatus for use in mine
disasters.
At the Pittsburg testing station there are a number of all kinds of
apparatus. The tests of these are to determine ease of use, of repair,
durability, safety under all conditions, period during which the supply
of artificial air or oxygen can be relied on, and other essential data.
In addition to the central testing station, sub-stations for training
miners, and as headquarters for field investigation as to the causes of
mine disasters and for rescue work in the more dangerous coal fields,
have been established; at Urbana, Ill., in charge of Mr. R. Y. Williams,
Mining Engineer; at Knoxville, Tenn., in charge of Mr. J. J. Rutledge,
Mining Engineer; at McAlester, Okla., in charge of Mr. L. M. Jones,
Assistant Mining Engineer; and at Seattle, Wash., in charge of Mr. Hugh
Wolflin, Assistant Mining Engineer. Others may soon be established in
Colorado and elsewhere, in charge of skilled mining engineers who have
been trained in this work at Pittsburg, and who will be assisted by
trained miners. It is not to be expected that under any but
extraordinary circumstances, such as those which occurred at Cherry,
Ill., the few Government engineers, located at widely scattered points
throughout the United States, can hope to save the lives of miners after
a disaster occurs. As a rule, all who are alive in the mine on such an
occasion, are killed within a few hours. This is almost invariably the
case after a dust explosion, and is likely to be true after a gas
explosion, although a fire such as that at Cherry, Ill., offers the
greatest opportunity for subsequent successful rescue operations. The
most to be hoped for from the Government engineers is that they shall
train miners and be available to assist and advise State inspectors and
mine owners, should their services be called for.
It should be borne in mind that the Federal Government has no police
duties in the States, and that, therefore, its employees may not direct
operations or have other responsible charge in the enforcement of State
laws. There is little reason to doubt that these Federal mining
engineers, both because of their preliminary education as mining
engineers and their subsequent training in charge of mine operations,
and more recently in mine-accidents investigations and rescue work, are
eminently fitted to furnish advice and assistance on such occasions. The
mere fact that, within a year, some of these men have been present at,
and assisted in, rescue work or in opening up after disasters at nearly
twenty of such catastrophes, whereas the average mining engineer or
superintendent may be connected with but one in a lifetime, should make
their advice and assistance of supreme value on such occasions. They
cannot be held in any way responsible for tardiness, however, nor be
unduly credited with effective measures taken after a mine disaster,
because of their lack of responsible authority or charge, except in
occasional instances where such may be given them by the mine owners or
the State officials, from a reliance on their superior equipment for
such work.
Successful rescue operations may only be looked for when the time, now
believed to be not far distant, has been reached when the mine operators
throughout the various fields will have their own rescue stations, as is
the practice in Europe, and have available, at certain strategic mines,
the necessary artificial breathing apparatus, and have in their employ
skilled miners who have been trained in rescue work at the Government
stations. Then, on the occurrence of a disaster, the engineer in charge
of the Government station may advise by wire all those who have proper
equipment or training to assemble, and it may be possible to gather,
within an hour or two of a disaster, a sufficiently large corps of
helmet-men to enable them to recover such persons as have not been
killed before the fire--which usually is started by the explosion--has
gained sufficient headway to prevent entrance into the mine. Without
such apparatus, it is essential that the fans be started, and the mine
cleared of gas. The usual effect of this is to give life to any
incipient fire. With the apparatus, the more dense the gas, the safer
the helmet-men are from a secondary explosion or from the rapid ignition
of a fire, because of the absence of the oxygen necessary to combustion.
The miners who were saved at Cherry, Ill., on November 20th, 1909, owe
their lives primarily to the work of the Government engineers. The
sub-station of the Survey at Urbana, Ill., was promptly notified of the
disaster on the afternoon of November 13th. Arrangements were
immediately made, whereby Mr. R. Y. Williams, Mining Engineer in Charge,
and his Assistant, Mr. J. M. Webb, with their apparatus, were rushed by
special train to the scene, arriving early the following day (Sunday).
Chief Mining Engineer, George S. Rice, Chief of Rescue Division, J. W.
Paul, and Assistant Engineer, F. F. Morris, learned of the disaster
through the daily press, at their homes in Pittsburg, on Sunday. They
left immediately with four sets of rescue apparatus, reaching Cherry on
Monday morning. Meantime, Messrs. Williams and Webb, equipped with
oxygen helmets, had made two trips into the shaft, but were driven out
by the heat. Both shafts were shortly resealed with a view to combating
the fire, which had now made considerable headway.
The direction of the operations at Cherry, was, by right of
jurisdiction, in charge of the State Mine Inspectors of Illinois, at
whose solicitation the Government engineers were brought into conference
as to the proper means to follow in an effort to get into the mine. The
disaster was not due to an explosion of coal or gas, but was the result
of a fire ignited in hay, in the stable within the mine. The flame had
come through the top of the air-shaft, and had disabled the ventilating
fans. A rescue corps of twelve men, unprotected by artificial breathing
apparatus, had entered the mine, and all had been killed. When the
shafts were resealed on Monday evening, the 15th, a small hole was left
for the insertion of a water-pipe or hose. During the afternoon and
evening, a sprinkler was rigged up, and, by Tuesday morning, was in
successful operation, the temperature in the shaft at that time being
109° Fahr. After the temperature had been reduced to about 100°, the
Federal engineers volunteered to descend into the shaft and make an
exploration. The rescue party, consisting of Messrs. Rice, Paul, and
Williams, equipped with artificial breathing apparatus, made an
exploration near the bottom of the air-shaft and located the first body.
After they had returned to the surface, three of the Illinois State
Inspectors, who had previously received training by the Government
engineers in the use of the rescue apparatus, including Inspectors Moses
and Taylor, descended, made tests of the air, and found that with the
fan running slowly, it was possible to work in the shaft. The rescue
corps then took hose down the main shaft, having first attached it to a
fire engine belonging to the Chicago Fire Department. Water was directed
on the fire at the bottom of the shaft, greatly diminishing its force,
and it was soon subdued sufficiently to permit the firemen to enter the
mine without the protection of breathing apparatus.
Unfortunately, these operations could be pursued only under the most
disadvantageous circumstances and surrounded by the greatest possible
precautions, due to the frequent heavy falls of roof--a result of the
heating by the mine fire--and the presence of large quantities of
black-damp. All movements of unprotected rescuers had to be preceded by
exploration by the trained rescue corps, who analyzed the gases, as the
fire still continued to burn, and watched closely for falls, possible
explosions, or a revival of the fire. While the heavy work of shoring
up, and removing bodies, was being carried on by the unprotected rescue
force, the helmet-men explored the more distant parts of the mine, and
on Saturday afternoon, November 20th, one week after the disaster, a
room was discovered in which a number of miners, with great presence of
mind, had walled themselves in in order to keep out the smoke and heat.
From this room 20 living men were taken, of whom 12 were recovered in a
helpless condition, by the helmet-men.
This is not the first time this Government mining corps has performed
valiant services. Directly and indirectly the members have saved from
fifteen to twenty lives in the short time they have been organized. At
the Marianna, Pa., disaster, the corps found one man still alive among
150 bodies, and he was brought to the surface. He recovered entirely
after a month in the hospital.
At the Leiter mine, at Zeigler, Ill., two employees, who had been
trained in the use of the oxygen helmets by members of the Government’s
corps, went down into the mine, following an explosion, and brought one
man to the surface, where they resuscitated him.
Equally good service, either in actual rescue operations, or in
explorations after mine disasters, or in fire-fighting, has been
rendered by this force at the Darr, Star Junction, Hazel, Clarinda,
Sewickley, Berwind-White No. 37, and Wehrum, Pa., mine disasters; at
Monongah and Lick Branch, W. Va.; at Deering, Sunnyside, and Shelburn,
Ind., Jobs, Ohio, and at Roslyn, Wash.
_Explosives Laboratory._--The rooms grouped at the south end of Building
No. 21, at Pittsburg, are occupied as a laboratory for the chemical
examination and analysis of explosives, and are in charge of Mr. W. O.
Snelling.
Samples of all explosives used in the testing gallery, ballistic
pendulum, pressure gauge, and other testing apparatus, are here
subjected to chemical analysis in order to determine the component
materials and their exact percentages. Tests are also made to determine
the stability of the explosive, or its liability to decompose at various
temperatures, and other properties which are of importance in showing
the factors which will control the safety of the explosive during
transportation and storage.
In the investigation of all explosives, the first procedure is a
qualitative examination to determine what constituents are present.
Owing to the large number of organic and inorganic compounds which enter
into the composition of explosive mixtures, this examination must be
thorough. Several hundred chemical bodies have been used in explosives
at different times, and some of these materials can be separated from
others with which they are mixed only by the most careful and exact
methods of chemical analysis.
Following the qualitative examination, a method is selected for the
separation and weighing of each of the constituents previously found to
be present. These methods, of course, vary widely, according to the
particular materials to be separated, it being usually necessary to
devise a special method of analysis for each explosive, unless it is
found, by the qualitative analysis, to be similar to some ordinary
explosive, in which case the ordinary method of analysis of that
explosive can be carried out. Most safety powders require special
treatment, while most grades of dynamite and all ordinary forms of black
blasting powder are readily analyzed by the usual methods.
The examination of black blasting powder has been greatly facilitated
and, at the same time, made considerably more accurate, by means of a
densimeter devised at this laboratory. In this apparatus a Torricellian
vacuum is used as a means of displacing the air surrounding the grains
of powder, and through very simple manipulation the true density of
black powder is determined with a high degree of accuracy. In Building
No. 17 there is an apparatus for separating or grading the sizes of
black powder (Fig. 1, Plate X).
By means of two factors, the moisture coefficient and the hygroscopic
coefficient, which have been worked out at this laboratory, a number of
important observations can be made on black powder, in determining the
relative efficiency of the graphite coating to resist moisture, and also
as a means of judging the thoroughness with which the components of the
powder are mixed. The moisture coefficient relates to the amount of
moisture which is taken up by the grains of the powder in a definite
time under standard conditions of saturation; and the hygroscopic
coefficient relates to the affinity of the constituents of the powder
for moisture under the same standard conditions.
Besides the examination of explosives used at the testing station, those
for the Reclamation Service, the Isthmian Canal Commission, and other
divisions of the Government, are also inspected and analyzed at the
explosives laboratory. At the present time, the Isthmian Canal
Commission is probably the largest user of explosives in the world, and
samples used in its work are inspected, tested, and analyzed at this
laboratory, and at the branch laboratories at Gibbstown and Pompton
Lakes, N.J., and at Xenia, Ohio.
Aside from the usual analysis of explosives for the Isthmian Canal
Commission, special tests are made to determine the liability of the
explosive to exude nitro-glycerine, and to deteriorate in unfavorable
weather conditions. These tests are necessary, because of the warm and
moist climate of the Isthmus of Panama.
_Gas and Dust Gallery No. 1._--Gallery No. 1 is cylindrical in form,
100 ft. long, and has a minimum internal diameter of 6⅓ ft. It consists
of fifteen similar sections, each 6⅔ ft. long and built up in in-and-out
courses. The first three sections, those nearest the concrete head, are
of ½-in. boiler-plate steel, the remaining twelve sections are of ⅜-in.
boiler-plate steel, and have a tensile strength of, at least, 55,000 lb.
per sq. in. Each section has one release pressure door, centrally placed
on top, equipped with a rubber bumper to prevent its destruction when
opened quickly. In use, this door may be either closed and unfastened,
closed and fastened by stud-bolts, or left open. Each section is also
equipped with one ¾-in. plate-glass window, 6 by 6 in., centrally placed
in the side of the gallery (Fig. 1, and Figs. 1 and 2, Plate VI). The
sections are held together by a lap-joint. At each lap-joint there is,
on the interior of the gallery, a 2½-in. circular, angle iron, on the
face of which a paper diaphragm may be placed and held in position by
semicircular washers, studs, and wedges. These paper diaphragms are used
to assist in confining a gas-and-air mixture.
[Illustration: Fig. 1.
EXPLOSIVES TESTING GALLERY No. 1]
Natural gas from the mains of the City of Pittsburg is used to represent
that found in the mines by actual analysis. A typical analysis of this
gas is as follows:
Volumetric Analysis of Typical Natural Gas.
Hydrogen gases 0
Carbon dioxide 0.1
Oxygen 0
Heavy hydrocarbons 0
Carbon monoxide 0
Methane 81.8
Ethane 16.8
Nitrogen 1.3
The volume of gas used is measured by an accurate test meter reading to
one-twentieth of a cubic foot. The required amount is admitted near the
bottom, to one or more of the 20-ft. divisions of the gallery, from a
2-in. pipe, 14 ft. long. The pipe has perforations arranged so that an
equal flow of gas is maintained from each unit length.
Each 20-ft. division of the gallery is further equipped with an exterior
circulating system, as shown by Fig. 1, thus providing an efficient
method of mixing the gas with the air. For the first division this
circulating system is stationary, a portion of the piping being equipped
with heating coils for maintaining a constant temperature.
The other divisions have a common circulating system mounted on a truck
which may be used on any of these divisions. Valves are provided for
isolating the fan so that a possible explosion will not injure it.
In the center section of each division is an indicator cock which is
used to provide means of recording pressures above and below
atmospheric, or of sampling the air-and-gas mixture. The first division
of the gallery is equipped with shelves laterally placed, for the
support of coal dust.
The cannon in which the explosive is fired is placed in the concrete
head, the axial line of the bore-hole being coincident with that of the
gallery. This cannon (Fig. 2) is similar to that used in the ballistic
pendulum. The charge is fired electrically from the observation room. To
minimize the risk of loading the cannon, the charger carries in his
pocket the plug of a stage switch (the only plug of its kind on the
ground), so that it is impossible to complete the circuit until the
charger has left the gallery. That portion of the first division of the
gallery which is not embedded in concrete, has a 3-in. covering made up
of blocks of magnesia, asbestos fiber, asbestos, cement, a thin layer of
8-oz. duck, and strips of water-proof roofing paper, the whole being
covered with a thick coat of graphite paint. The object of this covering
is to assist in maintaining a constant temperature.
[Illustration: PLATE VII.
Fig. 1.--Bichel Pressure Gauges.
Fig. 2.--Rate of Detonation Recorder.]
The entire gallery rests on a concrete foundation 10 ft. wide, which has
a maximum height of 4½ ft. and a minimum height of 2 ft.
The concrete head in which the cannon is placed completely closes that
end of the gallery. A narrow drain extends under the entire length of
the gallery, and a tapped hole at the bottom of each section provides an
efficient means of drainage.
[Illustration: Fig. 2.
{cannon as described in text} ]
The buildings near the gallery are protected by two barricades near the
open end, each 10 ft. high and 30 ft. long. A back-stop, consisting of a
swinging steel plate, 6 ft. high and 9 ft. long, 50 ft. from the end of
the gallery, prevents any of the stemming from doing damage.
Tests are witnessed from an observation room, a protected position about
60 ft. from the gallery. The walls of the room are 18 in. thick, and the
line of vision passes through a ½-in. plate glass, 6 in. wide and 37 ft.
long, and is further confined by two external guards, each 37 ft. long
and 3 ft. wide.
In this gallery a series of experiments has been undertaken to determine
the amount of moisture necessary with different coal dusts, in order to
reduce the likelihood of a coal-dust explosion from a blown-out shot of
one of the dangerous types of explosives.
Coal dust taken from the roads of one of the coal mines in the Pittsburg
district required at least 12% of water to prevent an ignition. It has
also been proven that the finer the dust the more water is required, and
when it was 100-mesh fine, 30% of water was required to prevent its
ignition by the flame of a blown-out shot in direct contact. The methods
now used in sprinkling have been proven entirely insufficient for
thoroughly moistening the dust, and hence are unreliable in preventing a
general dust explosion.
At this station successful experiments have been carried out by using
humidifiers to moisten the atmosphere after the temperature of the air
outside the gallery has been raised to mine temperature and drawn
through the humidifiers. It has been found that if a relative humidity
of 90%, at a temperature of 60° Fahr., is maintained for 48 hours,
simulating summer conditions in a mine, the absorption of moisture by
the dust and the blanketing effect of the humid air prevent the general
ignition of the dust.
These humidity tests have been run in Gas and Dust Gallery No. 1 with
special equipment consisting of a Koerting exhauster having a capacity
of 240,000 cu. ft. per hour, which draws the air out of the gallery
through the first doorway, or that next the concrete head in which the
cannon is embedded.
The other end of the gallery is closed by means of brattice cloth and
paper diaphragms, the entire gallery being made practically air-tight.
The air enters the fifteenth doorway through a box, passing over steam
radiators to increase its temperature, and then through the humidifier
heads.
EXPLOSIVES TESTING APPARATUS.
There is no exposed woodwork in Building No. 17, which is 40 by 60 ft.,
two stories high, and substantially constructed of heavy stone masonry,
with a slate roof. The structure within is entirely fire-proof. Iron
columns and girders, and wooden girders heavily encased in cement,
support the floors which are either of cement slab construction or of
wooden flooring protected by expanded metal and cement mortar, both
above and beneath. At one end, on the ground floor, is the exposing and
recording apparatus for flame tests of explosives, also pressure gauges,
and a calorimeter, and, at the other end, is a gallery for testing
safety lamps.
The larger portion of the second floor is occupied by a gas-tight
training room for rescue work, and an audience chamber, from which
persons interested in such work may observe the methods of procedure. A
storage room for rescue apparatus and different models of safety lamps
is also on this floor.
The disruptive force of explosives is determined in three ways, namely,
by the ballistic pendulum, by the Bichel pressure gauge, and by Trauzl
lead blocks.
_Ballistic Pendulum._--The disruptive force of explosives, as tested by
the ballistic pendulum, is measured by the amount of oscillation. The
standard unit of comparison is a charge of ½ lb. of 40% nitro-glycerine
dynamite. The apparatus consists essentially of a 12-in. mortar (Fig. 3,
Plate VI), weighing 31,600 lb., and suspended as a pendulum from a beam
having knife-edges. A steel cannon is mounted on a truck set on a track
laid in line with the direction of the swing of the mortar. At the time
of firing the cannon may be placed 1/16-in. from the muzzle of the
mortar. The beam, from which the mortar is suspended, rests on concrete
walls, 51 by 120 in. at the base and 139 in. high. On top of each wall
is a 1-in. base-plate, 7 by 48 in., anchored to the wall by ⅝-in. bolts,
28 in. long. The knife-edges rest on bearing-plates placed on these
base-plates. The bearing-plates are provided with small grooves for the
purpose of keeping the knife-edges in oil and protected from the
weather. The knife-edges are each 6 in. long, 2-11/16 in. deep from
point to back, 2 in. wide at the back, and taper 50° with the
horizontal, starting on a line 1½ in. from the back. The point is
rounded to conform to a radius of ¼ in. The back of each is 2 in. longer
than the edge, making a total length of 10 in., and is 1 in. deep and 12
in. wide. This shoulder gives bolting surface to the beam from which the
mortar is hung. The beam is of solid steel, has a 4 by 8-in. section,
and is 87 in. long. Heavy steel castings are bolted to it to take the
threads of the machine-steel rods which form the saddles on which the
mortar is suspended. The radius of the swing, measured from the point of
the knife-edges to the center of the trunnions, is 89¾ in.
The cannon consists of two parts, a jacket and a liner. The jacket is 36
in. long, has an external diameter of 24 in., and internal diameters of
9½ and 7½ in. It is made of the best cast steel or of forged steel.
The liner is 36½ in. long, with a 1-in. shoulder, 7¾ in. from the back,
changing the diameter from 9½ to 7½ in. The bore is smooth, being 2¼ in.
in diameter and 21½ in. long. The cannon rests on a 4-wheel truck, to
which it is well braced by straps and rods. A track of 30-in. gauge
extends about 9 ft. from the muzzle of the mortar to the bumper for the
cannon.
The shot is fired by an electric firing battery, from the first floor of
Building No. 17, about 10 yd. away. To insure the safety of the operator
and the charger, the man who loads the cannon carries a safety plug
without which the charge cannot be exploded. The wires for connecting to
the fuse after charging are placed conveniently, and the safety plug is
then inserted in a box at the end of the west wall. The completion of
the firing battery by the switch at the firing place is indicated by the
flashing of a red light, after which all that is necessary to set off
the charge is to press a button on the battery. An automatic recording
device at the back of the mortar records the length of swing which, by a
vernier, may be read to 1/200 in.
_Bichel Pressure Gauges._--Pressure gauges are constructed for the
purpose of determining the unit disruptive force of explosives
detonating at different rates of velocity, by measuring pressures
developed in an enclosed space from which the generated gases cannot
escape. The apparatus consists of a stout steel cylinder, which may be
made absolutely air-tight; an air-pump and proper connections for
exhausting the air in the cylinder to a pressure equivalent to 10 mm. of
mercury; an insulated plug for providing the means of igniting the
charge; a valve by which the gaseous products of combustion may be
removed for subsequent analysis; and an indicator drum (Fig. 1, Plate
VII) with proper connections for driving it at a determinable speed.
This apparatus is in the southeast corner of Building No. 17. The
cylinder is 31½ in. long, 19¾ in. in diameter, and is anchored to
a solid concrete footing at a convenient height for handling. The
explosion chamber is 19 in. long and 7⅞in. in diameter, with a capacity
of exactly 15 liters. The cover of the cylinder is a heavy piece of
steel held in place by stout screw-bolts and a heavy steel clamp.
The charge is placed on a small wire tripod, and connections are made
with a fuse to an electric firing battery for igniting the charges. The
cover is drawn tight, with the twelve heavy bolts against lead washers.
The air in the cylinder is exhausted to 10 mm., mercury column, in order
to approach more closely the conditions of a stemmed charge exploding in
a bore-hole inaccessible to air; the indicator drum is placed in
position and set in motion; and, finally, the shot is fired. The record
shown on the indicator card is a rapidly ascending curve for quick
explosives and a shallower, slowly rising curve for explosives of slow
detonation. When the gases cool, the curve merges into a straight line,
which indicates the pressures of the cooled gases on the sides of the
chamber.
[Illustration: PLATE VIII.
Fig. 1.--Explosives Calorimeter.
Fig. 2.--Building No. 17, and Flame-Test Apparatus.
Fig. 3.--Small Lead Block Test.]
Since the ratio of the volume of the cylinder to the volume of the
charge may be computed, the pressure of the confined charge may also be
found, and this pressure often exceeds 100,000 lb. per sq. in. The
cooling effect of the inner surface on the gaseous products of
combustion, a vital point in computations of the disruptive force of
explosives by this method, is determined by comparing the pressures
obtained in the original cylinder with those in a second cylinder of
larger capacity, into which has been inserted one or more steel
cylinders to increase the superficial area while keeping the volume
equal to that of the first cylinders. By comparing results, a curve may
be plotted, which will determine the actual pressures developed, with
the surface-cooling effect eliminated.
_Trauzl Lead Blocks._--The lead-block test is the method adopted by the
Fifth International Congress of Applied Chemistry as the standard for
measuring the disruptive force of explosives. The unit by this test is
defined to be the force required to enlarge the bore-hole in the block
to an amount equivalent to that produced by 10 grammes of standard 40%
nitro-glycerine dynamite stemmed with 50 grammes of dry sand under
standard conditions as produced with the tamping device. The results of
this test, when compared with those of the Bichel gauge, indicate that,
for explosives of high detonation, the lead block is quite accurate, but
for slow explosives, such as gunpowder, the expansion of the gases is
not fast enough to make comparative results of value. The reason for
this is that the gases escape through the bore of the block rather than
take effect in expanding the bore-hole.
The lead blocks are cylindrical, 200 mm. in diameter, and 200 mm. high.
Each has a central cavity, 25 mm. in diameter and 125 mm. deep (Fig. 1,
Plate IX), in which the charge is placed. The blocks are made of
desilverized lead of the best quality, and, as nearly as possible, under
identical conditions. The charge is placed in the cavity and prepared
for detonation with an electrical exploder and stemming. After the
explosion the bore-hole is pear-shaped, the size of the cavity
depending, not only on the disruptive power of the explosive, but also
on its rate of detonation, as already indicated. The size of the
bore-hole is measured by filling the cavity with water from a burette.
The difference in the capacity of the cavity before and after detonation
indicates the enlarging power of the explosive.
_Calorimeter._--The explosion calorimeter is designed to measure the
amount of heat given off by the detonation of explosive charges of 100
grammes. The apparatus consists of the calorimeter bomb (Fig. 1, Plate
VIII), the inner receiver or immersion vessel, a wooden tub, a
registering thermometer, and a rocking frame. This piece of apparatus
stands on the east side of Building No. 17.
The bottle-shaped bomb is made of ½-in. wrought steel, and has a
capacity of 30 liters. On opposite sides near the top are bored
apertures, one for the exhaust valve for obtaining a partial vacuum
(about 20 mm., mercury column) after the bomb has been charged, the
other for inserting the plug through which passes the fuse wire for
igniting the charge. The bomb is closed with a cap, by which the chamber
may be made absolutely air-tight. It is 30 in. high with the cap on,
weighs 158 lb., and is handled to and from the immersion vessel by a
small crane.
The inner receiver is made of 1/16-in. sheet copper, 30⅞ in. deep, and
with an inner diameter of 17⅞ in. It is nickel-plated, and strengthened
on the outside with bands of copper wire, and its capacity is about 70
liters. The outer tub is made of 1-in. lumber strengthened with four
brass hoops on the outside. It is 33 in. deep, and its inner diameter
is 21 in.
The stirring device, operated vertically by an electric motor, consists
of a small wooden beam connected to a system of three rings having a
horizontal bearing surface. When the apparatus is put together, the
inner receiver rests on a small standard on top of the base of the outer
tank, and the rings of the stirring device are run between the bomb and
the inner receiver. The bomb itself rests on a small standard placed on
the bottom of the inner receiver. The apparatus is provided with a
snugly fitting board cover. The bomb is charged from the top, the
explosive being suspended in its center. The air is exhausted to the
desired degree of rarification. The caps are then screwed on, and the
apparatus is set together as described.
[Illustration: PLATE IX.
Fig. 1.--Trauzl Lead Blocks.
Fig. 2.--Powder Flames.]
The apparatus is assembled on scales and weighed before the water is
poured in and after the receiver is filled. From the weight of the water
thus obtained and the rise of temperature, the calorific value may be
computed. The charge is exploded by electricity, while the water is
being stirred. The rise in the temperature of the water is read by a
magnifying glass, from a thermometer which measures temperature
differences of 0.01 degree. From the readings obtained, the maximum
temperature of explosion may be determined, according to certain
formulas for calorimetric experiments. Proper corrections are made for
the effects, on the temperature readings, of the formation of the
products of combustion, and for the heat-absorbing power of the
apparatus.
_Impact Machine._--In Building No. 17, at the south side, is an impact
machine designed to gauge the sensitiveness of explosives to shock. For
this purpose, a drop-hammer, constructed to meet the following
requirements, is used: A substantial, unyielding foundation; minimum
friction in the guide-grooves; and no escape or scattering of the
explosive when struck by the falling weight. This machine is modeled
after one used in Germany, but is much improved in details of
construction.
The apparatus, Fig. 1, Plate XI, consists essentially of the following
parts: An endless chain working in a vertical path and provided with
lugs; a steel anvil on which the charge of explosive is held by a steel
stamp; a demagnetizing collar moving freely in vertical guides and
provided with jaws placed so that the lugs of the chain may engage them;
a steel weight sliding loosely in vertical guides and drawn by the
demagnetizing collar to determinable heights when the machine is in
operation; a second demagnetizing collar, which may be set at known
heights, and provided with a release for the jaws of the first collar;
and a recording device geared to a vertically-driven threaded rod which
raises or lowers, sets the second demagnetizing collar, and thus
determines the height of fall of the weight. By this apparatus the
weight may be lifted to different known heights, and dropped on the
steel stamp which transmits the shock to the explosive. The fall
necessary to explode the sample is thus determined.
The hammers are of varying weight, the one generally used weighing
2,000 grammes. As the sensitiveness of an explosive is influenced by
temperature changes, water at 25° cent. is allowed to flow through the
anvil in order to keep its temperature uniform.
_Flame Test._--An apparatus, Fig. 2, Plate VIII, designed to measure
the length and duration of flames given off by explosives, is placed at
the northeast corner of Building No. 17. It consists essentially of a
cannon, a photographing device, and a drum geared for high speed, to
which a sensitized film may be attached.
About 13 ft. outside the wall of Building No. 17, set in a concrete
footing, is a cannon pointing vertically into an encasing cylinder or
stack, 20 ft. high and 43 in. in diameter. This cannon is a duplicate of
the one used for the ballistic pendulum, details of which have already
been given. The stack or cylinder is of ¼-in. boiler plate, in
twenty-four sections, and is absolutely tight against light at the base
and on the sides. It is connected with a dark room in Building No. 17 by
a light-tight conduit of rectangular section, 12 in. wide, horizontal on
the bottom, and sloping on the top from a height of 8¼ ft. at the stack
to 21 in. at the inside of the wall of the building.
The conduit is carefully insulated from the light at all joints, and is
riveted to the stack. A vertical slit, 2 in. wide and 8 ft. long,
coincident with the center line of the conduit, is cut in the stack. A
vertical plane drawn through the center line of the bore-hole of the
cannon and that of the slit, if produced, intersects the center line of
a quartz lens, and coincides with the center of a stenopaic slit and the
axis of the revolving drum carrying the film. The photographing
apparatus consists of a shutter, a quartz lens, and a stenopaic slit, 76
by 1.7 mm., between the lens and the sensitized film on the rotary drum.
The quartz lens is used because it will focus the ultra-violet rays,
which are those attending extreme heat.
The drum is 50 cm. in circumference and 10 cm. deep. It is driven by a
220-volt motor connected to a tachometer which reads both meters per
second and revolutions per minute. A maximum peripheral speed of 20 m.
per sec. may be obtained.
When the cannon is charged, the operator retires to the dark room in
which the recording apparatus is located, starts the drum, obtains the
desired speed, and fires the shot by means of a battery. When developed,
the film shows a blur of certain dimensions, produced by the flame from
the charge. From the two dimensions--height and lateral
displacement--the length and duration of the flame of the explosive are
determined.
The results of flame tests of a permissible explosive and a test of
black blasting powder, all shot without stemming, are shown on Fig. 2,
Plate IX. In this test, the speed of the drum carrying the black powder
negative was reduced to one sixty-fourth of that for the permissible
explosives, in order that the photograph might come within the limits of
the negative. In other words, the duration of the black powder flame, as
shown, should be multiplied by 64 for comparison with that of the
permissible explosive, which is from 3,500 to 4,000 times quicker.
_Apparatus for Measuring Rate of Detonation._--The rate at which
detonation travels through a given length of an explosive can be
measured by an apparatus installed in and near Building No. 17. Its most
essential feature is a recording device, with an electrical connection,
by which very small time intervals can be measured with great exactness.
The explosive is placed in a sheet-iron tube about 1½ in. in diameter
and 4 ft. long, and suspended by cords in a pit, 11 ft. deep and 16 ft.
in diameter. This pit was once used as the well of a gas tank, Fig. 2,
Plate VIII. In adapting the pit to its new use, the tank was cut in two;
the top half, inverted, was placed in the pit on a bed of saw-dust, and
the space between the tank and the masonry walls of the pit was filled
with saw-dust. The cover of the pit consists of heavy timbers framed
together and overlaid by a 12-in. layer of concrete reinforced by six
I-beams. Four straps extend over the top and down to eight “deadmen”
planted about 8 ft. below the surface of the ground.
The recording device, known as the Mettegang recorder, Fig. 2, Plate
VII, comprises two sparking induction coils and a rapidly revolving
metallic drum driven by a small motor, the periphery of the drum having
a thin coating of lampblack. A vibration tachometer which will indicate
any speed between 50 and 150 rev. per sec., is directly connected to the
drum, so that any chance of error by slipping is eliminated. The wires
leading to the primary coils of the sparking coils pass through the
explosive a meter or more apart. Wires lead from the secondary coils to
two platinum points placed a fraction of a millimeter from the periphery
of the drum. A separate circuit is provided for the firing lines.
In making a test, the separate cartridges, with the paper trimmed from
the ends, are placed, end to end, in the sheet-iron tube; the drum is
given the desired peripheral speed, and the charge is exploded. The
usual length between the points in the tube is 1 m., and the time
required for the detonation of a charge of that length is shown by the
distance between the beginning of two rows of dots on the drum made by
the sparks from the secondary coil circuits, the dots starting the
instant the primary circuits are broken by the detonation. At one end of
the drum are gear teeth, 1 mm. apart on centers, which can be made to
engage a worm revolving a pointer in front of a dial graduated to
hundredths; by means of this and a filar eyepiece, the distance between
the start of the two rows of spark dots on the drum can be measured
accurately to 0.01 mm. As the drum is 500 mm. in circumference, and its
normal speed is 86 rev. per sec., it is theoretically possible to
measure time to one four-millionth of a second, though with a cartridge
1 m. long, such refinement has not been found necessary.
The use of small lead blocks affords another means of determining the
rate of detonation or quickness of an explosive. Each block (a cylinder,
2½ in. long and 1½ in. in diameter) is enclosed in a piece of paper so
that a shell is formed above the block, in which to place the charge. A
small steel disk of the same diameter as the block is first placed in
the shell on top of the block, then the charge with a detonator is
inserted. The charge is customarily 100 grammes. On detonation of the
charge, a deformation of the lead takes place, the amount of which is
due to the quickness of the explosive used (Fig. 3, Plate VIII).
Sample Record of Tests.
The procedure followed in the examination of an explosive is shown by
the following outline:
1.--_Physical Examination._
(_a_).--Record of appearance and marks on original package.
(_b_).--Dimensions of cartridge.
(_c_).--Weight of cartridge, color and specific gravity of powder.
2.--_Chemical Analysis._
(_a_).--Record of moisture, nitro-glycerine, sodium or potassium
nitrate, and other chemical constituents, as set forth by the
analysis; percentage of ash, hygroscopic coefficient--the amount of
water taken up in 24 hours in a saturated atmosphere, at 15° cent.,
by 5 grammes, as compared with the weight of the explosive.
(_b_).--Analysis of products of combustion from 100 grammes, including
gaseous products, solids, and water.
(_c_).--Composition of gaseous products of combustion, including
carbon monoxide and carbon dioxide, hydrogen, nitrogen, etc.
(_d_).--Composition of solid products of combustion, subdivided into
soluble and insoluble.
_3.--A Typical Analysis of Natural Gas._
Used in tests, as follows:
Carbon dioxide 0.0 per cent.
Heavy hydrocarbons 0.2 ” ”
Oxygen 0.1 ” ”
Carbon monoxide 0.0 ” ”
Methane 82.4 ” ”
Ethane 15.3 ” ”
Nitrogen 2.0 ” ”
-----
100.00 per cent.
_4.--Typical Analysis of Bituminous Coal Dust, 100-Mesh Fine, Used in
Tests._
Moisture 1.90
Volatile matter 35.05
Fixed carbon 58.92
Ash 4.13
------
100.00
Sulphur 1.04
_5.--An Average Analysis of Detonators._
Used on Trauzl lead blocks, pressure gauge, calorimeter, and small lead
blocks:
M - l(l/m). Triple-strength exploder.
Charge 1.5729 grammes.
Mercury Chlorate
fulminate. of potash.
Specification 89.73 10.27
Used on all other tests:
M - 260(l/m). Double-strength exploder.
Charge 0.9805 grammes.
Mercury Chlorate
fulminate. of potash.
Specification 91.31 8.69
_6.--Ballistic-Pendulum Tests._
This record includes powder used, weight of charge, swing of mortar, and
unit disruptive charge, the latter being the charge required to produce
a swing of the mortar equal to that produced by ½ lb. (227 grammes) of
40% dynamite, or 3.01 in.
_7.--Record of Tests._
Tests Nos. 1 to 5 in Gallery No. 1, as set forth in preceding circular.
_8.--Trauzl Lead-Block Test._
Powder and test numbers, expansion of bore-hole in cubic centimeters,
and average expansion compared with that produced by a like quantity (10
grammes) of 40% dynamite, the latter giving an average expansion of 294
cu. cm.
_9.--Pressure Gauge._
Powder and test number, weight of charge, charging density, height of
curve, pressure developed, and pressure developed after cooling,
compared with pressure developed after elimination of surface influences
by a like quantity (100 grammes) of 40% dynamite, the average being
8,439 kg. per sq. cm.
_10.--Rate of Detonation._
Powder and test number, size of cartridge, and rate of detonation in
meters per second, for comparison with rate of detonation of 40%
dynamite, which, under the same conditions, averages 4,690 m. per sec.
_11.--Impact Machine._
Explosive and test numbers, distance of fall (2,000-gramme weight)
necessary to cause explosion, for comparison with length of fall, 11
cm., necessary to cause explosion of 40% dynamite.
_12.--Distance of Explosive Wave Transmitted by 1.25 by 8-in.
Cartridge._
Explosive and test numbers, weight of cartridge, distance separating
cartridges in tests, resulting explosion or non-explosion, for
comparison with two cartridges of 40% dynamite, hung, under identical
conditions, 13 in. apart, end to end, in which case detonation of the
first cartridge will explode the second.
_13.--Flame Test._
Explosive and test numbers, charge 100 grammes with 1 lb. of clay
stemming, average length of flame and average duration of flame, for
comparison with photographs produced by 40% dynamite under like
conditions.
[Illustration: PLATE X.
Fig. 1.--Separator for Grading Black Powder.
Fig. 2.--Safety Lamp Testing Gallery.
Fig. 3.--Mine Gallery No. 2.]
_14.--Small Lead Blocks._
Powder and test numbers, weight of charge, and compression produced in
blocks.
_15.--Calories Developed._
Number of large calories developed per kilogramme of explosive, for
comparison with 1,000 grammes of 40% dynamite, which develop, on an
average, 1,229 large calories.
Blasting Powder Separator.
The grains of black blasting powder are graded by a separator, similar
to those used in powder mills, but of reduced size. It consists of an
inclined wooden box, with slots on the sides to carry a series of
screens, and a vertical conduit at the end for carrying off the grains
as they are screened into separate small bins (Fig. 1, Plate X). At the
upper end of the screens is a small 12 by 16-in. hopper, with a sliding
brass apron to regulate the feed. The screens are shaken laterally by an
eccentric rod operated by hand. The top of the hopper is about 6½ ft.
above the floor. The box is 6 ft. 10 in. long, from tip to tip, and
inclines at an angle of 9 degrees.
After separation the grains fall through a vertical conduit, and thence
to the bins through zinc chutes, 1 by 2 in. in section. Care is taken to
have no steel or iron exposed to the powder.
The screens are held by light wooden frames which slip into the inclined
box from the upper end. In this way, any or all of the screens may be
used at once, thus separating all grades, or making only such
separations as are desired. The screens with the largest meshes are
diagonally-perforated zinc plates. Table 2 gives the number of holes per
square foot in zinc plates perforated with circular holes of the
diameters stated.
TABLE 2.--Number of Holes per Square Foot in Zinc Plates with Circular
Perforations.
-------------+------------
Diameter, | Number
in inches | of holes.
-------------+------------
1/2 | 353
4/10 | 518
1/3 | 782
1/4 | 1,392
1/6 | 1,680
1/8 | 3,456
1/10 | 6,636
1/16 | 12,800
-------------+------------
The finer meshes are obtained by using linen screens with holes of two
sizes, namely, 1/20 in. square and 1/28 in. square.
Until a few years ago, black blasting powder was manufactured in the
sizes given in Table 3.
TABLE 3.--Gradation of Black Blasting Powder.
---------+-----------
Grade. | Mesh.
---------+-----------
CC | 2 - 2½
C | 2½ - 3
F | 3 - 5
FF | 5 - 8
FFF | 8 - 16
FFFF | 16 - 28
---------+-----------
In late years there has been considerable demand for special sizes and
mixed grains for individual mines, especially in Illinois. As no
material change has been made in the brands, the letters now used are
not indicative of the size of the grains, which they are supposed to
represent. Of 29 samples of black blasting powder recently received from
the Illinois Powder Commission, only 10 were found to contain 95% of the
size of grains they were supposed to represent; 4 contained 90%; 7
varied from 80 to 90%; several others were mixtures of small and large
grains, and were branded FF black blasting powder; and one sample
contained only 8.5% of the size of grains it was supposed to represent.
The remaining samples showed many variations, even when sold under the
same name. The practice of thus mixing grades is exceedingly dangerous,
because a miner, after becoming accustomed to one brand of FF powder of
uniform separation, may receive another make of similar brand but of
mixed grains, and, consequently, he cannot gauge the quantity of powder
to be used. The result is often an over-load or a blown-out shot. The
smaller grains will burn first, and the larger ones may be thrown out
before combustion is complete, and thus ignite any fire-damp present.
Lamp Testing Gallery.
At the Pittsburg testing station, there is a gallery for testing safety
lamps in the presence of various percentages of inflammable gas. In this
gallery the safety of the lamps in these gaseous mixtures may be tested,
and it is also possible for mine inspectors and fire bosses to bring
their safety lamps to this station, and test their measurements of
percentage of gas, by noting the length and the appearance of the flame
in the presence of mixtures containing known percentages of methane and
air.
[Illustration: PLATE XI.
Fig. 1.--Impact Machine.
Fig. 2.--Lamp Testing Box.]
The gas-tight gallery used for testing the lamps, consists of a
rectangular conduit (Fig. 2, Plate X), having sheet-steel sides, 6 mm.
thick and 433 mm. wide, the top and bottom being of channel iron. The
gallery rests on two steel trestles, and to one end is attached a No. 5
Koerting exhauster, capable of aspirating 50 cu. m. per min., under a
pressure of 500 mm. of water, with the necessary valve, steam separator,
etc. The mouth of the exhauster passes through the wall of the building
and discharges into the open air.
Besides the main horizontal conduit, there are two secondary conduits
connected by a short horizontal length, and the whole is put together so
that the safety lamp under test may be placed in a current of air, or of
air and gas, which strikes it horizontally, vertically upward or
downward, or at an angle of 45° (Fig. 3). The path of the current is
determined by detachable sheet-steel doors.
[Illustration: Fig. 3.
SAFETY LAMP TESTING GALLERY]
There are five double observing windows of plate glass, which open on
hinges. The size of each window is 7½ by 3 in.; the inner glass is ¼ in.
thick and the outer one, ½ in. thick. These glasses are separated by a
space of ¼ in. The upper conduit has four safety doors along the top,
each of the inclined conduits has one safety door, and the walls and
windows are provided with rubber gaskets or asbestos packing, to make
them gas-tight. The cross-sectional area of the conduit is 434 sq. cm.
The air inlet consists of 36 perforations, 22 mm. in diameter, in a
bronze plate or diaphragm. The object of this diaphragm is to produce
pressure in the conduit before the mixing boxes, and permit the
measuring of the velocity of the current. The air-current, after passing
through the holes, enters the mixer, a cast-steel box traversed by 36
copper tubes, each perforated by 12 openings, 3 mm. in diameter,
arranged in a spiral along its length and equally spaced. The total
cross-sectional area of the tubes is 137 sq. cm.
The explosive gas enters the interior of the box around the tubes
through large pipes, each 90 mm. in diameter, passes thence through the
432 openings in the copper tubes, and mixes thoroughly with the air
flowing through these tubes. The current through the apparatus is
induced by the exhauster, and its course is determined by the position
of the doors.
The gallery can be controlled so as to provide rapidly and easily a
current of known velocity and known percentage of methane. In the
explosive current of gas and air, safety lamps of any size or design can
be tested under conditions simulating those found occasionally in mines,
air-currents containing methane in dangerous proportions striking the
lamps at different angles, and the relative safety of the various types
of lamps under such conditions can be determined. In this gallery it is
also possible to test lighting devices either in a quiet atmosphere or
in a moving current, and, by subjecting the lamps to air containing
known percentages of methane, it is possible to acquaint the user with
the appearance of the flame caps.
Breathing Apparatus.
With this apparatus, the wearer may explore a gaseous mine, approach
fires for the purpose of fighting them, or make investigations after an
explosion. Its object is to provide air or oxygen to be breathed by the
wearer in coal mines, when the mine air is so full of poisonous gases as
to render life in its presence impossible.
A variety of forms of rescue helmets and apparatus are on the market,
almost all of European manufacture, which are being subjected to
comparative trials as to their durability and safety, the ease or
inconvenience involved in their use, etc. All consist essentially of
helmets which fit air-tight about the head, or of air-tight nose clamps
and mouthpieces (Fig. 1, Plate XII).
These several forms of breathing apparatus are of three types:
1.--The liquid-air type, in which air, in a liquid state, evaporates and
provides a constant supply of fresh air.
2.--The chemical oxygen-producing type, which artificially makes or
supplies oxygen for breathing at about the rate required; and,
3.--The compressed-oxygen type.
[Illustration: PLATE XII.
Fig. 1.--Breathing and Rescue Apparatus.
Fig. 2.--Rescue Training Room.]
Apparatus of the first type, weighing 20 lb., supplies enough air to
last about 3 hours, and the products of breathing pass through a
check-valve directly into space. Apparatus of the second type supplies
oxygen obtained from oxygen-producing chemicals, and also provides means
of absorbing the carbonic acid gas produced in respiration. They contain
also the requisite tubes, valves, connections, etc., for the
transmission of the fresh air and the respired air so as to produce
sufficient oxygen while in use; to absorb and purify the products of
expiration; and to convey the fresh air to the mouth without
contamination by the atmosphere in which the apparatus is used. Three
oxygen-generating cartridges are provided, each supplying oxygen enough
for 1 hour, making the total capacity 3 hours. Changes of cylinders can
be made in a few seconds while breathing is suspended. This apparatus
weighs from 20 to 25 lb., according to the number of oxygen generators
carried. The cartridges for generating oxygen, provided with this
apparatus, are of no value after having been used for about an hour.
The third type of apparatus is equipped with strong cylinders charged
with oxygen under high pressure; two potash regenerative cans for
absorbing the carbon dioxide gas exhaled; a facial helmet; the necessary
valves, tubes, etc., for the control of the oxygen; and a finimeter
which registers the contents of the cylinders in atmospheres and minutes
of duration. The two cartridges used for absorbing the carbonic acid gas
are of no value after having been in use for two hours.
If inhalation is through the mouth alone, a mouthpiece is attached to
the end of the breathing tube by which the air or oxygen is supplied,
the nose is closed by a clip, and the eyes are protected by goggles. To
inhale through both nose and mouth, the miner wears a helmet or headgear
which can be made to fit tightly around the face. The helmet has two
tubes attached, one for inspiration and the other for expiration. In the
oxygen-cylinder apparatus these tubes lead to and from rubber sacks used
for pure-air and bad-air reserves.
Mine-Rescue Training.
It has been found in actual service that when a miner, equipped with
breathing apparatus for the first time, enters a mine in which an
explosion has occurred, he is soon overcome by excitement or nervousness
induced by the artificial conditions of breathing imposed by the
apparatus, the darkness and heat, and the consciousness that he is
surrounded with poisonous gases. It has also been found that a brief
period of training in the use of such apparatus, under conditions
simulating those encountered in a mine after a disaster, gives the miner
confidence and enables him to use the apparatus successfully under the
strain of the vigorous exertion incident to rescue work.
The rescue corps consists of five or six miners under the direction of
a mining engineer who is experienced in rescue operations and familiar
with the conditions existing after mine disasters. The miners work in
pairs, so that one may assist the other in case of accident, or of
injury to the breathing apparatus, and so that each may watch the
condition of the oxygen supply, as shown by the gauges in the other’s
outfit.
The training is given in the gas-tight room of Building No. 17, or in
similar rooms at sub-stations (Fig. 2, Plate XII). This room is made
absolutely dark, and is filled with formaldehyde gas, SO_{2}, CO_{2}, or
CO, produced by burning sulphur or charcoal on braziers. At each period
of training, the miners enter and walk a distance of about 1 mile, the
average distance usually traveled from the mine mouth to the working
face or point of explosion. They then remove a number of timbers; lift a
quantity of brick or hard lump-coal into wheel-barrows; climb through
artificial tunnels, up and down inclines, and over surfaces strewn with
coal or stone; operate a machine with a device attached to it, which
automatically records the foot-pounds of work done; and perform other
vigorous exercise, during a period of 2 hours. This routine is repeated
daily during 1 week, after which the rescue corps is considered
sufficiently trained for active service.
The apparatus used for recording the foot-pounds of work done by the
person operating the work machine within the gas-tight rescue room,
comprises a small dial with electrical connections, which records the
number of strokes made by the machine, and a pencil point which rests on
a paper diaphragm, fastened to a horizontal brass disk. This disk is
driven by clockwork, and makes one complete revolution per hour. When
the machine is in operation, the pencil point works back and forth,
making a broad line on the paper; when the operator of the machine
rests, the pencil point traces a single line. The apparatus thus records
the number of strokes given by the operator during a given time. From
the weight lifted, the height of lift, and the number of strokes in the
given time, the foot-pounds of work are readily calculated.
Electric Testing Apparatus.
On the ground floor of Building No. 10, two rooms are occupied as
laboratories for investigating the electrical equipment used in mining
operations. The purpose of these investigations is to ascertain the
conditions under which electricity of various voltages may be used with
safety--in mine haulage, hoisting, pumping, or lighting--in the presence
of dangerous mixtures of explosive gases or of dust. It is also proposed
to test various kinds of insulation and insulators in this laboratory,
and to determine the durability of such insulation in the presence of
such corrosive gases and water as are found in mines.
A water-proof wooden tank, measuring 15 by 5 by 5 ft., is installed, in
which insulation and insulating materials are tested under either pure
or polluted water. Various electric lighting devices and equipment can
be connected from a switch-board in Building No. 17 with Gas-and-Dust
Gallery No. 2, for testing the effect of such lighting apparatus in the
presence of explosive mixtures of gas and dust, as set forth on page
220.
In the electrical laboratory, Building No. 10, is a booster set
developing 60 kw., and an appropriate switch-board for taking direct
current at 220 volts from the turbo-generator and converting it into
current varying from 0 to 750 volts. There are also transformers for
developing 60-cycle, alternating current at voltages of from 110 to
2,200. The switch-board is designed to handle these various voltages and
to communicate them to the apparatus under test in Building No. 10,
Gallery No. 2, or elsewhere.
Tests are in progress of insulating materials for use in mines, and of
electric fuses, lights, etc., in Gallery No. 2 (Fig. 3, Plate X), and in
the lamp-testing box (Fig. 2, Plate XI). It is proposed, at the earliest
possible date, to make comparative tests of the safety of various mine
locomotives and mine-hoisting equipment through the medium of this
laboratory, and it is believed that the results will furnish valuable
information as a guide to the safety, reliability, and durability of
these appliances when electrically operated.
_Electric Lamp and Fuse Testing Box._--An apparatus for testing safety
lamps and electric lights and fuses, consists of ¼-in. iron plates,
bolted together with 1½ in. angle-irons to form a box with inside
dimensions of 18 by 18 by 24 in. The box is placed on a stand at such a
height that the observation windows are on a level with the observer’s
eye (Fig. 2, Plate XI), and it is connected, by a gas-pipe, with a
supply of natural gas which can be measured by a gas-holder or meter
alongside the box.
By the use of this apparatus the effect of explosive gas on flames, of
electric sparks on explosive mixtures of gas and air, and of breaking
electric lamps in an explosive mixture of gas and air, may be studied.
The safety lamps are introduced into the box from beneath, through a
hole 6 in. square, covered with a hinged iron lid, admission to which is
had through a flexible rubber sleeve, 20 in. long.
The behavior of the standard safety lamp and of the safety lamps
undergoing test may be compared in this box as to height of flame for
different percentages of methane in the air, the effect of such flames
in igniting gas, etc.
In each end of the box is an opening 1 ft. square, over which may be
placed a paper diaphragm held by skeleton doors, the purpose of which
is to confine the gas in such a manner that, should an explosion occur,
no damage would be done. In the front of the box are two plate-glass
observing windows, 2⅝ by 5½ in. In the side of the box, between the
two windows, is a ⅜-in. hole, which can be closed by a tap-screw,
through which samples for chemical analysis are drawn.
The gasometer consists of two iron cans, the lower one being open at
the top and filled with water and the upper one open at the bottom and
suspended by a counterweight. The latter has attached to its upper
surface a scale which moves with it, thereby measuring the amount of
gas in the holder. A two-way cock permits the admission of gas into the
gasometer and thence into the testing box.
_Gas-and-Dust Gallery No. 2._--This gallery is constructed of sheet
steel and is similar to Gallery No. 1, the length, however, being only
30 ft. and the diameter 10 ft. It rests on a concrete foundation (Fig.
3, Plate X). Diaphragms can be placed across either extremity, or at
various sections, to confine the mixtures of gas and air in which the
tests are made. The admission of gas is controlled by pipes and valves,
and the gas and air can be stirred or mixed by a fan, as described for
Gallery No. 1, and as shown by Fig. 1.
Gallery No. 2 is used for investigating the effect of flames of various
lamps, of electric currents, motors, and coal-cutting machines, in the
presence of known mixtures of explosive gas and air. It is also used for
testing the length of flame of safety lamps in still air carrying
various proportions of methane, and, for this purpose, is more
convenient than the lamp gallery. In tests with explosive mixtures,
after the device to be tested has been introduced and preparations are
completed, operations are controlled from a safe distance by a
switch-board in a building near-by.
Among other investigations conducted in this gallery are those of the
effect of sparks on known gas mixtures. These sparks are such as those
struck from a pick on flint, but in this case they are produced by
rubbing a rapidly revolving emery wheel against a steel file. The effect
of a spark produced by a short circuit of known voltage, the flame from
an arc lamp, etc., may also be studied in this gallery.
STRUCTURAL MATERIALS INVESTIGATIONS.
The structural materials investigations are being conducted for the
purpose of determining the nature and extent of the materials available
for use in the building and construction work of the Government, and how
these materials may be used most efficiently.
These investigations include:
(1).--Inquiries into the distribution and local availability, near each
of the building centers in the United States, of such materials as are
needed by the Government.
(2).--How these materials may be used most efficiently.
(3).--Their fire-resisting qualities and strength at different
temperatures.
(4).--The best and most economic methods of protecting steel by
fire-resistant covering.
(5).--The most efficient methods of proportioning and mixing the
aggregate, locally available, for different purposes.
(6).--The character and value of protective coatings, or of various
mixes, to prevent deterioration by sea water, alkali, and other
destructive agencies.
(7).--The kinds and forms of reinforcement for concrete necessary to
secure the greatest strength in beams, columns, floor slabs, etc.
(8).--Investigation of the clays and of the products of clays needed in
Government works, as to their strength, durability, suitability as
fire-resisting materials, and the methods of analyzing and testing clay
products.
(9).--Tests of building stones, and investigations as to their
availability near the various building centers throughout the United
States.
The operations of the Structural Materials Division include
investigations into cement-making materials, constituent materials of
concrete, building stones, clays, clay products, iron, steel, and
miscellaneous materials of construction, for the use of the Government.
The organization comprises a number of sections, including those for the
chemical and physical examination of Departmental purchases; field
sampling and laboratory examination of constituent materials of concrete
collected by skilled field inspectors in the neighborhood of the larger
commercial and building centers; similar field sampling of building
stones and of clays and clay products, offered for use in Government
buildings or engineering construction; and the forwarding of such
samples to the testing laboratories at St. Louis or Pittsburg for
investigation and test. The investigative tests include experiments
regarding destructive agencies, such as electrolysis, alkaline earths
and waters, salt water, fire, and weathering; also experiments with
protective and water-proofing agencies, including the various washes or
patented mixtures on the market, and the methods of washing, and mixing
mortars and concrete, which are likely to result in rendering such
materials less pervious to water.
Investigations are also being conducted to determine the nature and
extent of materials available for use in the building-construction work
of the Government, and how these materials may be used most efficiently
and safely. While the act authorizing this work does not permit
investigations or tests for private parties, it is believed that these
tests for the Government cannot fail to be of great general value. The
aggregate expenditure by the Federal Government in building and
engineering construction is about $40,000,000 annually. This work is
being executed under so many different conditions, at points so widely
separated geographically, and requires so great a variety of materials,
that the problems to be solved for the Government can hardly fail to
cover a large share of the needs of the Engineering Profession, State
and municipal governments, and the general public.
_Character of the Work._--The tests and analyses, of the materials of
construction purchased by the various bureaus and departments for the
use of the Government, are to determine the character, quality,
suitability, and availability of the materials submitted, and to
ascertain data leading to more accurate working values as a basis for
better working specifications, so as to enable Government officials to
use such materials with more economy and increased efficiency.
Investigative tests of materials entering into Government construction,
relative to the larger problems involved in the use of materials
purchased by the Government, include exhaustive study of the suitability
for use, in concrete construction on the Isthmian Canal, of the sand and
stone, and of the cementing value of pozzuolanic material, found on the
Isthmus; the strength, elasticity, and chemical properties of structural
steel for canal lock-gates; of wire rope and cables for use in hoisting
and haulage; and the most suitable sand and stone available for concrete
and reinforced concrete for under-water construction, such as the
retaining walls being built by the Quartermaster’s Department of the
Army, in San Francisco Harbor.
These tests also include investigations into the disintegrating effect
of alkaline soil and water on the concrete and reinforced concrete
structures of the Reclamation Service, with a view to preventing such
disintegration; investigations into the proper proportions and
dimensions of concrete and reinforced concrete structural columns,
beams, and piers, and of walls of brick and of building stone, and of
the various types of metal used for reinforcement by the Supervising
Architect in the construction of public buildings; investigations into
the sand, gravel, and broken stone available for local use in concrete
construction, such as columns, piers, arches, floor slabs, etc., as a
guide to the more economical design of public structures, and to
determine the proper method of mixing the materials to render the
concrete most impervious to water and resistant to weather and other
destructive agencies.
Other lines of research may be stated briefly as follows:
The extent to which concrete made from cement and local materials can be
most safely and efficiently used for different purposes under different
conditions;
The best methods for mixing and utilizing the various constituent
materials locally available for use in Government construction;
The materials suitable for the manufacture of cement on the public
lands, or where the Government has planned extensive building or
engineering construction work, where no cement plants now exist;
The kinds and forms of reinforcement for concrete, and the best methods
of applying them in order to secure the greatest strength in
compression, tension, shear, etc., in reinforced concrete beams,
columns, floor slabs, etc.;
The influence of acids, oils, salts, and other foreign materials,
long-continued strain, or electric currents, on the permanence of the
steel in reinforced concrete;
The value of protective coatings as preventives of deterioration of
structural materials by destructive agencies; and
The establishment of working stresses for various structural materials
needed by the Government in its buildings.
Investigations are being made into the effects of fire and the rate of
conductivity of heat on concrete and reinforced concrete, brick, tile,
building stone, etc., as a guide to the use of the most suitable
materials for fire-proof building construction and the proper
dimensioning of fire-resistive coverings.
Investigations and tests are being made, with a view to the preparation
of working specifications for use in Government construction, of bricks,
tile, sand-lime brick, paving brick, sewer pipe, roofing slates,
flooring tiles, cable conduits, electric insulators, architectural terra
cotta, fire-brick, and all shapes of refractories and other clay
products, regarding which no satisfactory data for the preparation of
specifications of working values now exist.
Investigations of the clay deposits throughout the United States are in
progress, to determine proper methods of converting them into building
brick, tile, etc., at the most reasonable cost, and the suitability of
the resulting material for erection in structural forms and to meet
building requirements.
Investigations are being made in the field, of building stones locally
available, and physical and chemical tests of these building stones to
determine their bearing or crushing strength; the most suitable mortars
for use with them; their resistance to weathering; their fire-resistive
and fire-proof qualities, etc., regarding which practically no adequate
information is available as a guide to Government engineering and
building design.
_Results Accomplished._--During one period of six months alone, more
than 2,500 samples, taken from Government purchases of structural
materials, were examined, of which more than 300 failed to meet the
specified requirements, representing many thousands of dollars worth of
inferior material rejected, which otherwise would have been paid for by
the Government. These tests were the means of detecting the inferior
quality of large quantities of materials delivered on contracts, and the
moral effect on bidders has proven as important a factor in the
maintenance of a high quality of purchases, as in the saving of money.
The examination of sands, gravels, and crushed stones, as constituent
materials for concrete and reinforced concrete construction, has
developed data showing that certain materials, locally available near
large building centers and previously regarded as inferior in quality,
were, in fact, superior to other and more expensive materials which it
had been proposed to use.
These investigations have represented an actual saving in the cost of
construction on the work of the Isthmian Canal Commission, of the
Supervising Architect, and of certain States and cities which have
benefited by the information disseminated regarding these constituent
materials.
Investigations of clay products, only recently inaugurated, have already
resulted in the ascertainment of important facts relative to the colloid
matter of clay and its measurement, and the bearing thereof on the
plasticity and working values of various clays. The study of the
preliminary treatment of clays difficult to handle dry, has furnished
useful information regarding the drying of such clays, and concerning
the fire resistance of bricks made of soft, stiff, or dried clay of
various densities.
The field collection and investigation of building-stone samples have
developed some important facts which had not been considered previously,
relative to the effect of quarrying, in relation to the strike and dip
of the bedding planes of building stone, and the strength and durability
of the same material when erected in building construction. These
investigations have also developed certain fundamental facts relative to
the effects of blasting (as compared with channeling or cutting) on the
strength and durability of quarried building stone.
_Mineral Chemistry Laboratories._--Investigations and analyses of the
materials of engineering and building construction are carried on at
Pittsburg in four of the larger rooms of Building No. 21. In this
laboratory, are conducted research investigations into the effect of
alkaline waters and soils on the constituent materials of concrete
available in arid regions, as related to the life and permanency of the
concrete and reinforced concrete construction of the Reclamation
Service. These investigations include a study of individual salts found
in particular alkalis, and a study of the results of allowing solutions
of various alkalis to percolate through cylinders of cement mortar and
concrete. Other research analyses have to do with the investigation of
destructive and preservative agencies for concrete, reinforced concrete,
and similar materials, and with the chemistry of the effects of salt
water on concrete, etc. The routine chemical analyses of the constituent
materials of concrete and cement-making materials, are made in this
laboratory, as are also a large number of miscellaneous chemical
analyses and investigations of reinforcement metal, the composition of
building stones, and allied work.
A heat laboratory, in charge of Dr. J. K. Clement, occupies three rooms
on the ground floor of Building No. 21, and is concerned chiefly with
the measurement of temperatures in gas producers, in the furnaces of
steam boilers, kilns, etc. The work includes determinations of the
thermal conductivity of fire clays, concrete, and other building
materials, and of their fire-resisting properties; measurements of the
thermal expansion and specific heats of fire-bricks, porcelain, and
glazes; and investigations of the effect of temperature variations on
the various chemical processes which take place in the fuel bed of the
gas producer, boiler furnace, etc.
The heat laboratory is equipped for the calibration of the thermometers
and pyrometers, and electrical and other physical apparatus used by the
various sections of the Technologic Branch.
For convenience in analyzing materials received from the various
purchasing officers attached to the Government bureaus, this work is
housed in a laboratory on the fourth floor of the Geological Survey
Building in Washington.
Large quantities and many varieties of building materials for use in
public buildings under contract with the Supervising Architect’s office,
are submitted to the laboratory by contractors to determine whether or
not they meet the specified requirements. Further examinations are made
of samples submitted by superintendents of construction, representing
material actually furnished by contractors. It is frequently found that
the sample of material submitted by the contractor is of far better
quality than that sent by the superintendent to represent deliveries.
The needed constant check on deliveries is thus provided.
In addition to this work for the office of the Supervising Architect,
similar work on purchases and supplies is carried on for the Isthmian
Canal Commission, the Quartermaster-General’s Department of the Army,
the Life Saving Service, the Reclamation Service, and other branches of
the Government. About 300 samples are examined each month, requiring an
average of 12 determinations per sample, or about 3,600 determinations
per month.
The chemical laboratory for testing Government purchases of structural
materials is equipped with the necessary apparatus for making the
requisite physical and chemical tests. For the physical tests of cement,
there are a tensile test machine, briquette moulds, a pat tank for
boiling tests to determine soundness, water tanks for the storage of
briquettes, a moist oven, apparatus to determine specific gravity,
fineness of grinding, etc.
The chemical laboratory at Washington is equipped with the necessary
analytical balances, steam ovens, baths, blast lamps, stills, etc.,
required in the routine chemical analysis of cement, plaster, clay,
bricks and terra cotta, mineral paints and pigments, roofing material,
tern plate and asphaltic compounds, water-proofing materials, iron and
steel alloys, etc.
At present, materials which require investigative tests as a basis for
the preparation of suitable specifications, tests not connected with the
immediate determination as to whether or not the purchases are in
accordance with the specifications, are referred to the chemical
laboratories attached to the Structural Materials Division, at
Pittsburg.
The inspection and tests of cement purchased in large quantities, such
as the larger purchases on behalf of public-building construction under
the Supervising Architect, or the great 4,500,000-bbl. contract of the
Isthmian Canal Commission, are made in the cement-testing laboratory of
the Survey, in the Lehigh Portland cement district, at Northampton, Pa.
_Testing Machines._--The various structural forms into which concrete
and reinforced concrete may be assembled for use in public-building
construction, are undergoing investigative tests as to their compressive
and tensile strength, resistance to shearing, modulus of elasticity,
coefficient of expansion, fire-resistive qualities, etc. Similar tests
are being conducted on building stone, clay products, and the structural
forms in which steel and iron are used for building construction.
The compressive, tensile, and other large testing machines, for all
kinds of structural materials reaching the testing stations, are under
the general supervision of Richard L. Humphrey, M. Am. Soc. C. E. The
immediate direction of the physical tests on the larger testing machines
is in charge of Mr. H. H. Kaplan.
Most of this testing apparatus, prior to 1909, was housed in buildings
loaned by the City of St. Louis, in Forest Park, St. Louis, Mo., and the
arrangement of these buildings, details of equipment, organization, and
methods of conducting the tests, are fully set forth in Bulletin No. 329
of the U.S. Geological Survey. In brief, this equipment included
motor-driven, universal, four-screw testing machines, as follows: One
600,000-lb., vertical automatic, four-screw machine; one 200,000-lb.,
automatic, four-screw machine; and one 200,000-lb. and one 100,000-lb.
machine of the same type, but with three screws. There are a number of
smaller machines of 50,000, 40,000, 10,000, and 2,000 lb., respectively.
These machines are equipped so that all are available for making tensile
and compressive tests (Fig. 1, Plate XIII). The 600,000-lb. machine is
capable of testing columns up to 30-ft. lengths, and of making
transverse tests of beams up to 25-ft. span, and tension tests for
specimens up to 24 ft. in length. The smaller machines are capable of
making tension and compressive tests up to 4 ft. in length and
transverse beam tests up to 12 ft. span. In addition, there are ample
subsidiary apparatus, including concrete mixers with capacities of ½ and
1 cu. yd., five hollow concrete block machines, automatic sifting
machines, briquette moulds, storage tanks, etc.
At the Atlantic City sub-station, there is also a 200,000-lb.,
universal, four-screw testing machine, with miscellaneous equipment for
testing cement and moulding concrete, etc.; and at the Northampton
sub-station, there is a complete equipment of apparatus for cement
testing, capable of handling 10,000 bbl. per day.
At the Pittsburg testing station, a 10,000,000-lb., vertical,
compression testing machine (Plate XIV), made by Tinius Olsen and
Company, is being erected for making a complete series of comparative
tests of various building stones of 2, 4, and 12-in. cube, of stone
prisms, 12 in. base and 24 in. high, of concrete and reinforced concrete
columns up to 65 ft. in height, and of brick piers and structural-steel
columns up to the the limits of the capacity and height of the machine.
[Illustration: PLATE XIII.
Fig. 1.--Testing Beam in 200,000-Lb. Machine.
Fig. 2.--Fire Test of Panel.]
This machine is a large hydraulic press, with an adjustable head, and a
weighing system for recording the loading developed by a triple-plunger
pump. It has a maximum clearance of 65 ft. between heads; the clearance
in the machine is a trifle more than 6 ft. between screws, and the heads
are 6 ft. square.
The machine consists of a base containing the main cylinder, with a
sectional area of 2,000 sq. in., upon which rests the lower platform or
head, which is provided with a ball-and-socket bearing. The upper head
is adjustable over four vertical screws, 13½ in. in diameter and 72 ft.
2 in. long, by a system of gearing operating four nuts with
ball-bearings upon which the head rests. The shafting operating this
mechanism is connected with a variable-speed motor which actuates
the triple-plunger pump supplying the pressure to the main cylinder
(Fig. 4).
The weighing device consists of a set of standard Olsen levers for
weighing one-eightieth of the total load on the main cylinder. This
reduction is effected through the medium of a piston and a diaphragm.
The main cylinder has a diameter of 50 in., and the smaller one, a
diameter of 5-9/16 in. The weighing beam is balanced by an
automatically-operated poise weight, and is provided with a device for
applying successive counterweights of 1,000,000 lb. each. Each division
on the dial is equivalent to a 100-lb. load, and smaller subdivisions
are made possible by an additional needle-beam.
The power is applied by a 15-h.p., 220-volt, variable-speed motor
operating a triple-plunger pump, the gearing operating the upper head
being driven by the same motor. The extreme length of the main screws
necessitates splicing, which is accomplished as follows:
In the center of the screws, at the splice, is a 3-in. threaded pin for
centering the upper and lower screws; this splice is strengthened by
sleeve nuts, split to facilitate their removal whenever it is necessary
to lower the upper head; after the head has passed the splice, the
sleeve nuts are replaced.
In order to maintain a constant load, a needle-valve has been provided,
which, when the pump is operated at its lowest speed, will allow a
sufficient quantity of oil to flow into the main cylinder to equalize
whatever leakage there may be. The main cylinder has a vertical movement
of 24 in. The speed of the machine, for the purpose of adjustment, using
the gearing attached to the upper head, is 10 in. per min. The speed for
applying loads, controlled by the variable-speed motor driving the pump,
varies from a minimum of at least 1/60 in. per min. to a maximum of at
least ½ in. per min. The machine has a guaranteed accuracy of at least
one-third of 1%, for any load of more than 100,000 lb., up to its
capacity.
[Illustration: Fig. 4.
PLAN AND ELEVATION OF 10,000,000-LB. VERTICAL COMPRESSION
TESTING MACHINE]
The castings for the base and the top head weigh approximately 48,000
lb. each. Each main screw weighs more than 40,000 lb., the lower
platform weighing about 25,000 lb., and the main cylinder, 16,000 lb.
The top of the machine will be about 70 ft. above the top of the floor,
and the concrete foundation, upon which it rests, is about 8 ft. below
the floor line.
[Illustration: PLATE XIV.
10,000,000-Lb. Testing Machine.]
_Concrete and Cement Investigations._--The investigations relating to
concrete include the examination of the deposits of sand, gravel, stone,
etc., in the field, the collection of representative samples, and the
shipment of these samples to the laboratory for analysis and test. These
tests are conducted in connection with the investigation of cement
mortars, made from a typical Portland cement prepared by thoroughly
mixing a number of brands, each of which must meet the following
requirements:
Specific gravity, not less than 3.10;
Fineness, residue not to exceed 8% on No. 100, nor 25% on No. 200
sieve;
Time of setting: Initial set, not less than 30 min.; hard set, not
less than 1 hour, nor more than 10 hours.
Tensile strength: Requirements applying to neat cement and to 1 part
cement with 3 parts standard sand:
-------------------------------+--------------+----------
| Neat cement. | 1:3 Mix.
Time specification. | Pounds. | Pounds.
-------------------------------+--------------+----------
24 hours in moist air | 175 | ...
7 days (1 day in moist air, | 500 | 175
6 days in water) | |
28 days (1 day in moist air, | 600 | 250
27 days in water) | |
-------------------------------+--------------+----------
Constancy of volume: Pats of neat cement, 3 in. in diameter, ½ in.
thick at center, tapering to a thin edge, shall be kept in moist air
for a period of 24 hours. A pat is kept in air at normal temperature
and observed at intervals for at least 28 days. Another pat is kept in
water maintained as near 70° Fahr. as practicable, and is observed at
intervals for at least 28 days. A third pat is exposed in an
atmosphere of steam above boiling water, in a loosely-closed vessel,
for 5 hours. These pats must remain firm and hard and show no signs of
distortion, checking, cracking, or disfiguration.
The cement shall not contain more than 1.75% of anhydrous sulphuric
acid, nor more than 4% of magnesium oxide.
A test of the neat cement must be made with each mortar series for
comparison of the quality of the typical Portland cement.
The constituent materials are subjected to the following examination and
determinations, and, in addition, are analyzed to determine the
composition and character of the stone, sand, etc.:
1.--Mineralogical examination,
2.--Specific gravity,
3.--Weight, per cubic foot,
4.--Sifting (granulometric composition),
5.--Percentage of silt and character of same,
6.--Percentage of voids,
7.--Character of stone as to percentage of absorption, porosity,
permeability, compressive strength, and behavior under treatment.
Physical tests are made to determine the tensile, compressive, and
transverse strengths of the cement and mortar test pieces, with various
preparations of cement and various percentages of material. Tests are
also made to determine porosity, permeability, volumetric changes in
setting, absorption, coefficient of expansion, effect of oil, etc.
Investigation of concretes made from mixtures of typical Portland
cement, sand, stone, and gravel, includes tests on cylinders, prisms,
cubes, and other standard test pieces, with various proportions of
materials and at ages ranging from 30 to 360 days. Full-sized plain
concrete beams, moulded building blocks, reinforced concrete beams,
columns, floor slabs, arches, etc., are tested to determine the effect,
character, and amount of reinforcement, the effect of changes in volume,
size, and composition, and the effect of different methods of loading
and of supporting these pieces, etc.
These investigations include detailed inquiry in the field and research
in the chemical and physical laboratories regarding the effects of
alkaline soils and waters on structures of concrete being built by the
Reclamation Service in the arid regions. It has been noted that on
certain of the Reclamation projects, notably on the Sun River Project,
near Great Falls, Mont., the Shoshone Project, near Cody, Wyo., and the
Carlsbad and Hondo Projects in the Pecos Valley, N. Mex., structures of
concrete, reinforced concrete, building stones, brick, and tile, show
evidence of disintegration. This is attributed to the effects of
alkaline waters or soils coming into contact with the structures, or to
the constituent materials used. In co-operation with the Reclamation
Service, samples of the waters, soils, and constituent materials, are
collected in the field, and are subjected to careful chemical
examination in the mineral laboratories at Pittsburg.
[Illustration: PLATE XV.
Fig. 1.--Characteristic Failures of Reinforced Concrete Beams.
Fig. 2.--Arrangement of Static Load Test for Reinforced
Concrete Beams.]
The cylinders used in the percolation tests are composed of typical
Portland cement mixed with sand, gravel, and broken stone of known
composition and behavior, and of cement mixed with sand, gravel, and
broken stone collected in the neighborhood of the Reclamation projects
under investigation.
[Illustration: Fig. 5.
CROSS-SECTION OF APPARATUS FOR HOLDING PERMEABILITY-TEST PIECES]
It is also proposed to subject these test pieces, some made with water
of known purity, and others with alkaline water, to contact with
alkaline soils near the projects, and with soil of known composition
near the testing laboratories at Pittsburg. As these tests progress and
other lines of investigation are developed, the programme will be
extended, in the hope that the inquiry may develop methods of preparing
and mixing concrete and reinforced concrete which can be used in
alkaline soils without danger of disintegration.
Investigations into the effect of salt water on cement mortars and
concretes, and the effect of electrolysis, are being conducted at
Atlantic City, N.J., where the test pieces may be immersed in deep sea
water for longer or shorter periods of time.
At the Pittsburg laboratory a great amount of investigative work is done
for the purpose of determining the suitability and availability of
various structural materials submitted for use by the Government. While
primarily valuable only to the Government, the results of these tests
are of indirect value to all who are interested in the use of similar
materials. Among such investigations have been those relating to the
strength, elasticity, and chemical properties of wire rope for use in
the Canal Zone; investigations of the suitability and cementing value of
concrete, sand, stone, and pozzuolanic material found on the Isthmus;
investigations as to the relative resistance to corrosion of various
types of wire screens for use in the Canal Zone; into the suitability
for use, in concrete sea-wall construction, of sand and stone from the
vicinity of San Francisco; into the properties of reinforced concrete
floor slabs; routine tests of reinforcing metal, and of reinforced
concrete beams and columns, for the Supervising Architect of the
Treasury Department, etc. The results have been set forth in three
bulletins[9] which describe the methods of conducting these tests and
also tests on constituent materials of concrete and plain concrete
beams. In addition, there are in process of publication a number of
bulletins giving the results of tests on reinforced concrete beams,
columns, and floor slabs, concrete building blocks, etc.
The Northampton laboratory was established because it is in the center
of the Lehigh cement district, and therefore available for the mill
sampling and testing of purchases of cement made by the Isthmian Canal
Commission; it is also available for tests of cement purchased in the
Lehigh district by the Supervising Architect and others. It is in a
building, the outer walls of which are of cement plaster applied over
metal lath nailed to studding. The partitions are of the same
construction, and the floors and roof are of concrete throughout.
The inspection at the factories and the sampling of the cement are under
the immediate direction of the Commission; the testing is under the
direction of the U.S. Geological Survey. A large force of employees is
required, in view of the magnitude of the work, which includes the daily
testing of consignments ranging from 5,000 to 10,000 bbl., sampled in
lots of 100 bbl., which is equivalent to from 50 to 100 samples tested
per day.
The cement to be sampled is taken from the storage bins and kept under
seal by the chief inspector pending the results of the test. The
quantity of cement sampled is sufficient for the tests required under
the specifications of the Isthmian Canal Commission, as well as for
preliminary tests made by the cement company, and check tests made at
the Geological Survey laboratory, at Pittsburg.
The tests specified by the Commission include determination of specific
gravity, fineness of grinding, time of setting, soundness, tensile
strength (with three parts of standard quartz sand for 7 and 28 days,
respectively), and determination of sulphur anhydride (SO_{3}), and
magnesia (MgO).
The briquette-making and testing room is fitted with a mixing table,
moist closet, briquette-storage tanks, and testing machines. The mixing
table has a concrete top, in which is set plate glass, 18 in. square and
1 in. thick. Underneath the table are shelves for moulds, glass plates,
etc.
The moist closet, 5 ft. high, 3 ft. 10 in. wide, and 1 ft. 8 in. deep,
is divided into two compartments by a vertical partition, and each
compartment is fitted with cleats for supporting thirteen tiers of glass
plates. On each pair of cleats, in each compartment, can be placed four
glass plates, each plate containing a 4-gang mould, making storage for
416 briquettes. With the exception of the doors, which are of wood lined
with copper, the closet is of 1:1 cement mortar, poured monolithic, even
to the cleats for supporting the glass plates.
The immersion tanks, of the same mortar, are in tiers of three,
supported by a steel structure. They are 6¼ ft. long, 2¼ ft. wide, and 6
in. deep, and 2,000 briquettes can be stored in each tank. The overflow
from the top tank wastes into the second, which, in turn, wastes into
the third. Water is kept running constantly.
The briquette-testing machine is a Fairbanks shot machine with a
capacity of 2,000 lb., and is regulated to apply the load at the rate of
600 lb. per min. Twenty-four 4-gang moulds, of the type recommended by
the Special Committee on Uniform Tests of Cement, of the American
Society of Civil Engineers, are used.
The room for noting time of set and soundness is fitted with a mixing
table similar to that in the briquette-making room. The Vicat apparatus
is used for determining the normal consistency, and the Gilmore
apparatus for the time of setting. While setting, the soundness pats are
stored in galvanized-iron pans having about 1 in. of water in the
bottom, and covered with dampened felt or burlap. The pats rest on a
rack slightly above the water and well below the felt.
For specific gravity tests, the Le Chatelier bottles are used. A pan, in
which five bottles can be immersed at one time, is used for maintaining
the benzine at a constant temperature. The samples are weighed on a pair
of Troemner’s No. 7 scales.
The fineness room is fitted with tables, two sets of standard No. 100
and No. 200 sieves, and two Troemner’s No. 7 scales similar to those
used for the specific gravity tests.
The storage room is fitted with shelves for the storage of samples being
held for 28-day tests.
The mould-cleaning room contains tables for cleaning moulds, and racks
for air pats.
An effort is made to keep all the rooms at a temperature of 70° Fahr.,
and, with this in view, a Bristol recording thermometer is placed in the
briquette-room. Two wet-and-dry bulb hygrometers are used to determine
the moisture in the air.
Samples are taken from the conveyor which carries the cement to the
storage bins, at the approximate rate of one sample for each 100 bbl.
After each 4,000-bbl. bin has been filled, it is sealed until all tests
have been made, when, if these have been satisfactory, it is released
for shipment.
The samples are taken in cans, 9 in. high and 7½ in. in diameter. These
cans are delivered in the preparation room where the contents are mixed
and passed through a No. 20 sieve. Separate samples are then weighed out
for mortar briquettes, for soundness pats, and for the specific-gravity
and fineness tests. These are placed in smaller cans and a quantity
sufficient for a re-test is held in the storage room awaiting the
results of all the tests.
The sample for briquettes is mixed with three parts standard crushed
quartz, and then taken to the briquette-making room, where eight
briquettes are made, four for 7-day and four for 28-day tests. These are
placed in the moist closet in damp air for 24 hours, then removed from
the moulds, and placed in water for the remainder of the test period. At
the proper time they are taken from the immersion tank and broken.
From the sample for soundness, four pats are made. The time of setting
is determined on one of these pats. They are placed in the pan
previously described, for 24 hours, then one is placed in running water
and one in air for 28 days. The others are treated in the boiler, one in
boiling water for 3 hours and one in steam at atmospheric pressure for 5
hours.
The sample taken for specific gravity and fineness is dried in the oven
at 100° cent. in order to drive off moisture. Two samples are then
carefully weighed out, 50 grammes for fineness and 64 grammes for
specific gravity, and the determinations are made. As soon as anything
unsatisfactory develops, a re-test is made. If, however, the cement
satisfies all requirements, a report sheet containing all the data for a
bin, is made out, and the cement is ready for shipment. From every fifth
bin, special neat and mortar briquettes are made, which are intended for
tests at ages up to ten years.
_Salt-Water Laboratory._--The laboratory at Atlantic City, for
conducting investigations into the effects of salt water on concrete and
reinforced concrete, is situated so that water more than 25 ft. deep is
available for immersion tests of the setting and deterioration of such
materials.
Through the courtesy of the municipality of Atlantic City, Young’s
cottage, on old Young’s Pier, has been turned over, at a nominal rental,
to the Geological Survey for the conduct of these tests. The laboratory
building is about 700 ft. from the boardwalk, and occupies a space about
100 by 45 ft. It is one story high, of frame-cottage construction, and
stands on wooden piles at one side of the pier proper and about 20 ft.
above the water, which is about 19 ft. deep at this point. Fresh running
water, gas, electric light, and electric power are supplied to the
building (Fig. 6).
In this laboratory investigations will be made of the cause of the
failure and disintegration of cement and concrete subjected to the
action of sea water. Tests are conducted so as to approach, as nearly as
possible, the actual conditions found in concrete construction along the
sea coast. All sea-water tests are made in the ocean, some will probably
be paralleled by ocean-water laboratory tests and all by fresh-water
comparative tests.
Cements, in the form of pats, briquettes, cubes, cylinders, and in a
loose ground state, and also mortars and concretes in cube, cylinder,
and slab form, are subjected to sea water.
The general plan for the investigations is as follows:
1.--Determination of the failing elements and the nature of the failure;
2.--Determination of the value of the theories advanced at the present
time; and,
3.--Determination of a method of eliminating or chemically recombining
the injurious elements.
Preliminary tests are in progress, including a study of the effect of
salt water on mortars and concretes of various mixtures and ages. The
proportions of these mixtures and the methods of mixing will be varied
from time to time, as suggested by the progress of the tests.
_Fire-Proofing Tests._--Tests of the fire-proofing and fire-resistive
properties of various structural materials are carried on in the
laboratories in Building No. 10, at Pittsburg, and in co-operation with
the Board or Fire Underwriters at its Chicago laboratory (Fig. 2, Plate
XIII). These tests include three essential classes of material: (_a_),
clay products, protective coverings representative of numerous varieties
of brick and fire-proofing tiles, including those on the market and
those especially manufactured for these tests in the laboratory at
Pittsburg; (_b_), characteristic granites of New England, with
subsequent tests of the various building stones found throughout the
United States; and (_c_), cement and concrete covering material,
building blocks, and concrete reinforced by steel bars embedded at
different depths for the purpose of studying the effect of expansion on
the protective covering.
In co-operation with the physical laboratory, these tests include a
study of the relative rates of conductivity of cement mortars and
concretes. By embedding thermo-couples in cylinders composed of the
materials under test, obtaining a given temperature by an electric coil,
and noting the time required to raise the temperature at the various
embedded couples to a given degree, the rate of conductivity may be
determined. Other tests include those in muffles to determine the rate
of expansion and the effect of heat and compressive stresses combined on
the compressive strength of the various structural materials. The
methods of making the panel tests, and the equipment used, are described
and illustrated in Bulletin No. 329, and the results of the tests have
been published in detail.[10]
_Building Stones Investigations._--The field investigations of building
stones are conducted by Mr. E. F. Burchard, and include the examination
of the various deposits found throughout the United States. A study of
the granites of New England has been commenced, which includes the
collection of type specimens of fine, medium, and coarse-grained
granites, and of dark, medium, and light-gray or white granites. A
comparative series of these granites, consisting of prisms and cubes of
4 and 2 in., respectively, has been prepared.
[Illustration: Fig. 6.
PLAN OF LABORATORY FOR SALT-WATER TESTS AT ATLANTIC CITY, N.J.]
The standard adopted for compressive test pieces in the 10,000,000-lb.
machine is a prism, having a base of 12 in. and being 24 in. high. The
tests include not only those for compression or crushing strength, but
also those for resistance to compressive strains of the prisms and
cubes, when raised to high temperatures in muffles or kilns; resistance
to weathering, freezing, and thawing; porosity; fire-resisting
qualities, etc.
In collecting field samples, special attention is paid to the occurrence
of the stone, extent of the deposit, strike, dip, etc., and specimens
are procured having their faces cut with reference to the bedding
planes, in order that compressive and weathering tests may be made, not
only in relation to these planes but at those angles thereto in which
the material is most frequently used commercially. Attention is also
paid to the results of blasting, in its relation to compressive strains,
as blasting is believed to have a material effect on stones, especially
on those which may occur in the foundations of great masonry dams, and
type specimens of stone quarried by channeling, as well as by blasting,
are collected and tested.
_Clay and Clay Products Investigations._--These investigations are in
charge of Mr. A. V. Bleininger, and include the study of the occurrence
of clay beds in various parts of the United States, and the adaptability
of each clay to the manufacture of the various clay products.
Experiments on grinding, drying, and burning the materials are conducted
at the Pittsburg testing station, to ascertain the most favorable
conditions for preparing and burning each clay, and to determine the
most suitable economic use to which it may be put, such as the
manufacture of building or paving bricks, architectural tiles, sewer
tiles, etc.
The laboratory is equipped with various grinding and drying devices,
muffles, kilns, and apparatus for chemical investigations, physical
tests, and the manufacture and subsequent investigative tests of clay
products.
This section occupies the east end of Building No. 10, and rooms on the
first and second floors have been allotted for this work. In addition, a
brick structure, 46 by 30 ft., provided with a 60-ft. iron stack, has
been erected for housing the necessary kilns and furnaces.
[Illustration: PLATE XVI.
Fig. 1.--Brick Machine and Universal Cutter.
Fig. 2.--House-Heating Boilers, Building No. 21.]
On the ground floor of Building No. 10, adjoining the cement and
concrete section, is a storage room for raw materials and product under
investigation. Adjoining this room, and connecting with it by wide
doors, is the grinding room, containing a 5-ft. wet pan, with 2,000-lb.
rollers, to be used for both dry and wet grinding. Later, a heavy dry
pan is to be installed. With these machines, even the hardest material
can be easily disintegrated and prepared. In this room there is also a
jaw crusher for reducing smaller quantities of very hard material, as
well as a 30 by 16-in. iron ball mill, for fine grinding. These machines
are belted to a line shaft along the wall across the building. Ample
sink drainage is provided for flushing and cleaning the wet pan, when
changing from one clay to another.
A large room adjoining is for the operation of all moulding and shaping
machines, representing the usual commercial processes. At present these
include an auger machine, with a rotary universal brick and tile cutter,
Fig. 1, Plate XVI, and a set of brick and special dies, a hand repress
for paving brick, and a hand screw press for dry pressing. The brick
machine is operated from the main shaft which crosses the building in
this room and is driven from a 50-h.p. motor. It is possible thus to
study the power consumption under different loads and with different
clays, as well as with varying degrees of water content in the clay. As
the needs of the work demand it, other types of machines are to be
installed. For special tests in which pressure is an important factor it
is intended to fit up one of the compression testing machines of the
cement section with the necessary dies, thus enabling the pressing to be
carried on under known pressures. Crushing, transverse, and other tests
of clay products are made on the testing machines of the cement and
concrete laboratories.
Outside of the building, in a lean-to, there is a double-chamber rattler
for the testing of paving brick according to the specifications of the
National Brick Manufacturers’ Association.
In the smaller room adjoining the machine laboratory there are two small
wet-grinding ball mills, of two and four jars, respectively, and also a
9-leaf laboratory filter press.
The remaining room on the first floor is devoted to the drying of clays
and clay wares. The equipment consists of a large sheet-iron drying oven
of special construction, which permits of close regulation of the
temperature (Fig. 7). It is heated by gas burners, and is used for the
preliminary heat treatment of raw clays, in connection with the study of
the drying problems of certain raw materials. It is intended to work
with temperatures as high as 250° cent.
Another drying closet, heated by steam coils (Fig. 8), intended for
drying various clay products, has been designed with special reference
to the exact regulation of the temperature, humidity, and velocity of
the air flowing through it. Both dryers connect by flues with an iron
stack outside the building. This stack is provided with a suction fan,
driven by a belt from an electric motor.
On the second floor are the chemical, physical, and research
laboratories, dealing with the precise manipulations of the tests and
investigations.
The chemical laboratory is fully equipped with the necessary apparatus
for carrying on special chemical research in silicate chemistry,
including electrical resistance furnaces, shaking devices, etc. It is
not the intention to do routine work in this laboratory. The office
adjoins this laboratory, and near it is the physical laboratory, devoted
to the study of the structure of raw materials. The latter contains
Nobel and Schoene elutriators, together with viscosimeters of the flow
and the Coulomb and Clark electrical types, sieves, voluminometers,
colorimeters, vernier shrinkage gauges, micrometers, microscopes, and
the necessary balances.
The room across the hall is devoted to the study of the specific
gravity, absorption, porosity, permeability, hardness, translucency,
etc., of burnt-clay products, all the necessary apparatus being
provided. In the two remaining rooms, intended for research work,
special apparatus adapted to the particular investigation may be set up.
All the rooms are piped for water, gas, compressed air, steam, and
drainage, and wired for light and power.
In the kiln house there is a test kiln adapted for solid fuel and gas.
It is of the down-draft type, with an available burning space of about 8
cu. ft. (Fig. 9). For heavier ware and the study of the fire behavior of
clay products under conditions approaching those of practice, a round
down-draft kiln, with an inside diameter of 6 ft., is installed. About
13 ft. above the floor level, and supported by iron beams, there is a
flue parallel to the long side of the structure. This flue conducts the
gases of the kilns to the stack, which is symmetrically located with
reference to the kiln house. Natural gas is the principal fuel. In
addition to these kilns, a small muffle furnace, fired with petroleum,
is provided for the determination of melting points, and an electric
carbon resistance furnace, with an aluminum muffle for high-temperature
work. For crucible-fusion work, a gas-fired pot furnace is installed.
[Illustration: Fig. 7.
CLAY-DRYING OVEN]
Along the north wall, bins are provided for the storage of fuel, clay,
sand, and other kiln supplies. There are two floor drainage sinks, and
electric current, steam, water, and compressed air, are provided.
[Illustration: Fig. 8.
DRYING CLOSETS FOR CERAMICS]
_Results of the Work._--More than 39,300 separate test pieces have been
made at the structural-materials testing laboratory. In connection with
the study of these, 86,000 tests and nearly 14,000 chemical analyses
have been made. Of these tests more than 13,600 have been of the
constituent materials of concrete, including tensile tests of cement
briquettes, compression tests of cylinders and cubes, and transverse
tests of various specimens.
Nearly 1,200 beams of concrete or reinforced concrete, each 13 ft. long
and 8 by 11 in. in cross-section, have been made, and, in connection
with the investigation of the behavior of these beams, nearly 3,000
tests have been made. Nearly 900 of these beams, probably more than
double the entire number made in other laboratories in the United
States, during a period of more than 15 years, have been tested.
In the section of building blocks, 2,200 blocks have been tested,
including, with auxiliary pieces, more than 4,500 tests; also, more than
900 pieces of concrete have been tested for permeability and shear. The
physical tests have numbered 14,000; tests of steel for reinforcement,
3,800; and 550 tests to determine fire-resistive qualities of various
building materials, have been made on 30 special panels, and on
miscellaneous pieces.
[Illustration: Fig. 9.
DOWN-DRAFT KILN]
The tests of the permeability of cement mortars and concretes, and of
water-proofing and damp-proofing materials, have numbered 3,470.
The results of the work of the Structural Materials Division have
already appeared in preliminary bulletins, as follows: No. 324, “San
Francisco Earthquake and Fire of April 18, 1906, and Their Effects on
Structures and Structural Materials”; No. 329, “Organization, Equipment,
and Operation of the Structural-Materials Testing Laboratories at St.
Louis, Mo.”; No. 331, “Portland Cement Mortars and Their Constituent
Materials” (based on nearly 25,000 tests); No. 344, “Strength of
Concrete Beams” (based on tests of 108 beams); No. 370, “Fire-Resistive
Properties of Various Building Materials”; No. 387, “The Colloid Matter
of Clay and its Measurements.” A bulletin on the results of tests of
reinforced concrete beams, one on the manufacture and chemistry of lime,
and one on drying tests of brick, are in course of publication.
FUEL INVESTIGATIONS.
The scope of the fuel investigations has been planned to conform to the
provisions of the Act of Congress which provides for analyzing and
testing coals, lignites, and other mineral fuel substances belonging to
the United States, or for the use of the United States Government, and
examinations for the purpose of increasing the general efficiency or
available supply of the fuel resources in the United States.
In conformity with this plan, the investigations inaugurated at St.
Louis had for their initial object the analyzing and testing of the
coals of the United States, using in this work samples of from 1 to 3
carloads, collected with great care from typical localities in the more
important coal fields of the country, with a view to determining the
relative values of those different fuels. In the work at Norfolk, during
1907, this purpose was modified to the extent of keeping in view
relative fuel efficiencies for naval purposes. The tests at Denver have
been on coal from Government land or from land contiguous thereto, and
are conducted solely with a view to perfecting methods of coking this
coal by prior washing and by manipulation in the process of coking.
Three general lines of inquiry are embodied in the plan of investigation
undertaken and contemplated by the Technologic Branch, after conference
and with the advice and approval of the Advisory Board: 1. The
ascertainment of the best mode of utilizing any fuel deposit owned or to
be used by the Government, or the fuel of any extensive deposit as a
whole, by conducting a more thorough investigation into its combustion
under steam boilers, conversion into producer gas, or into coke,
briquettes, etc. 2. The prevention of waste, through the study of the
possibility of improvement in the methods of mining, shipping,
utilizing, etc. 3. The inspection and analysis of coal and lignite
purchased under specification for the use of the Government, to
ascertain its heating value, ash, contained moisture, etc.
The first general line of work concerns the investigation and testing of
the fuel resources of the United States, and especially those belonging
to the Federal Government, to determine a more efficient and more
economical method of utilizing the same. This work has developed along
the following lines:
The collection of representative samples for chemical analysis, and
calorimeter tests by a corps of skilled mine samplers, from the mines
selected as typical of extensive deposits of coal in a given field or
from a given bed of coal; and the collection from the same mines of
larger samples of from 1 to 3 carloads, shipped to the testing station
for tests in boiler furnaces, gas producers, etc., as a check on the
analysis and calorimeter tests;
The testing of each coal received to determine the most efficient and
least wasteful method of use in different furnaces suitable for public
buildings or power plants or ships of the Government;
The testing of other portions of the same shipment of coal in the gas
producer, for continuous runs during periods of a few days up to several
weeks, in order to determine the availability of this fuel for use in
such producers, and the best method of handling it, to determine the
conditions requisite to produce the largest amount of high-grade gas
available for power purposes;
The testing of another portion of the same coal in a briquette machine
at different pressures and with different percentages and kinds of
binder, in order to determine the feasibility of briquetting the slack
or fine coal. Combustion tests are then made of these briquettes, to
determine the conditions under which they may be burned advantageously;
Demonstrations, on a commercial scale, of the possibility of producing
briquettes from American lignites, and the relative value of these for
purposes of combustion as compared with the run-of-mine coal from which
the briquettes are made;
The finding of cheaper binders for use in briquetting friable coals not
suited for coking purposes;
Investigations into the distribution, chemical composition, and
calorific value of the peat deposits available in those portions of the
United States where coal is not found, and the preparation of such peat
for combustion, by drying or briquetting, to render it useful as a local
substitute for coal;
Investigations into the character of the various petroleums found
throughout the United States, with a view to determining their calorific
value, chemical composition, and the various methods whereby they may be
made most economically available for more efficient use as power
producers, through the various methods of combustion;
Investigations and tests into the relative efficiency, as power
producers in internal-combustion engines, of the heavier distillates of
petroleum, as well as of kerosene and gasoline, in order to ascertain
the commercial value and relative efficiency of each product in the
various types of engines;
Investigations into the most efficient methods of utilizing the various
coals available throughout the United States for heating small public
buildings, army posts, etc., in order that these coals may be used more
economically than at present;
Investigative studies into the processes of combustion within boiler
furnaces and gas producers to ascertain the temperatures at which the
most complete combustion of the gases takes place, and the means whereby
such temperatures may be produced and maintained, thus diminishing the
loss of values up the smokestack and the amount of smoke produced;
Investigations and tests into the possibilities of coking coals which
have hitherto been classed as non-coking, and the making of comparative
tests of all coals found in the United States, especially those from the
public lands of the West;
Investigations, by means of washing in suitable machines, to determine
the possibility of improving the quality of American coals for various
methods of combustion, and with a view to making them more available for
the production of coke of high-grade metallurgical value, as free as
possible from sulphur and other injurious substances.
At each stage of the process of testing, samples of the coal have been
forwarded to the chemical laboratory for analyses; combustion
temperatures have been measured; and samples of gas collected from
various parts of the combustion chambers of the gas producers and boiler
furnaces have been analyzed, in order that a study of these data may
throw such light on the processes of combustion and indicate such
necessary changes in the apparatus, as might result in larger economies
in the use of coal.
The second line of investigation concerns the methods of mining and
preparing coal for the market, and the collection of mine samples of
coal, oil, etc., for analysis and testing. It is well known that, under
present methods of mining, from 10 to 75% of any given deposit of coal
is left underground as props and supports, or as low-grade material, or
in overlying beds broken up through mining the lower bed first. An
average of 50% of the coal is thus wasted or rendered valueless, as it
cannot be removed subsequently because of the caving or falling in of
the roofs of abandoned galleries and the breaking up of the adjoining
overlying beds, including coal, floor, and roof.
The investigations into waste in mining and the testing of the waste,
bone, and slack coal in gas producers, as briquettes, etc., have, for
their purpose, the prevention of this form of waste by demonstrating
that these materials, now wasted, may be used profitably, by means of
gas producers and engines, for power purposes.
The third general line of investigation concerns the inspection and
sampling of fuel delivered to the Government under purchase contracts,
and the analyzing and testing of the samples collected, to determine
their heating value and the extent to which they may or may not comply
with the specifications under which they are purchased. The coal
delivered at the public buildings in the District of Columbia is sampled
by special representatives of the Technologic Branch of the Survey. The
taking of similar samples at public buildings and posts throughout the
United States, and the shipment of the samples in hermetically sealed
cans or jars to the chemical laboratory at Washington, is for the most
part looked after by special officers or employees at each place. These
purchases are made, to an increasing extent, under specifications which
provide premiums for coal delivered in excess of standards, and
penalties for deliveries below standards fixed in the specifications.
The standard for bituminous coals is based mainly on the heat units,
ash, and sulphur, while that for anthracite coal is based mainly on the
percentage of ash and the heat units.
In connection with all these lines of fuel testing, certain research
work, both chemical and physical, is carried on to determine the true
composition and properties of the different varieties of coal, the
changes in the transformation from peat to lignite, from lignite to
bituminous coal, and from bituminous to anthracite coal, and the
chemical and physical processes in combustion. Experiments are conducted
concerning the destructive distillation of fuels; the by-products of
coking processes; the spontaneous combustion of coal; the storage of
coal, and the loss in value in various methods of storing; and kindred
questions, such as the weathering of coal. These experiments may yield
valuable results through careful chemical research work supplemented by
equally careful observations in the field.
_Inspection and Mine Sampling._--In the Geological Survey Building, at
Washington, coal purchased for Government use on a guaranteed-analysis
or heat-value basis, is inspected and sampled.
Some of the employees on this work are constantly at the mines taking
samples, or at public works inspecting coal for Government use, while
others are stationed at Washington to look after the deliveries of coal
to the many public buildings, and to collect and prepare samples taken
from these deliveries for analysis, as well as to prepare samples
received from public works and buildings in other parts of the country.
[Illustration: Fig. 10.
COAL-SAMPLING ROOM, GEOLOGICAL SURVEY, WASHINGTON, D.C.]
The preparation of these samples is carried on in a room in the basement
of the building, where special machinery has been installed for this
work. Fig. 10 shows a plan of this room and the arrangement of the
sampling and crushing machinery.
The crushing of the coal produces great quantities of objectionable
dust, and to prevent this dust from giving trouble outside the sampling
room, the wooden partitions on three sides of the room (the fourth side
being a masonry wall) are completely covered on the outside with
galvanized sheet iron. The only openings to the room are two doors,
which are likewise covered with sheet iron, and provided with broad
flanges of the same material, in order to seal effectually the openings
when the doors are shut. Fresh air is drawn into the room by a fan,
through a pipe leading to the outer air. A dust-collecting system which
carries the coal dust and spent air from the room, consists of an
arrangement of 8-in. and 12-in. pipes leading from hoods, placed over
the crushing machines, to the main furnace stack of the building. The
draft in this stack draws all the dust from the crushers directly
through the hoods to the main pipe, where most of it is deposited.
The equipment of the sampling room consists of one motor-driven, baby
hammer crusher, which has a capacity of about 1 ton per hour and crushes
to a fineness of ¼-in. mesh; one adjustable chipmunk jaw crusher, for 5-
and 10-lb. samples; one set of 4½ by 7½-in. rolls, crushing to 60 mesh,
for small samples; one large bucking board, and several different sizes
of riffle samplers for reducing samples to small quantities. The small
crushers are belted to a shaft driven by a separate motor from that
driving the baby crusher.
In conducting the inspection of departmental purchases of coal in
Washington, the office is notified whenever a delivery of coal is to be
made at one of the buildings, and an inspector is sent, who remains
during the unloading of the coal. He is provided with galvanized-iron
buckets having lids and locks; each bucket holds about 60 lb. of coal.
In these buckets he puts small quantities of the coal taken from every
portion of the delivery, and when the delivery has been completed, he
locks the buckets and notifies the office to send a wagon for them. The
buckets are numbered consecutively, and the inspector makes a record of
these numbers, the date, point of delivery, quality of coal delivered,
etc. The buckets are also tagged to prevent error. He then reports to
the office in person, or by telephone, for assignment to another point
in the city. All the samples are delivered to the crushing room in the
basement of the Survey Building, to be prepared for analysis.[11]
Samples taken from coal delivered to points outside of Washington are
taken by representatives of the department for which the coal is being
purchased, according to instructions furnished them, and, from time to
time, the regular inspectors are sent to see that these instructions are
being complied with. These samples are crushed by hand, reduced to about
2 lb. at the point where they are taken, and sent to Washington, in
proper air-tight containers, by mail or express, accompanied by
appropriate descriptions.
Each sample is entered in the sample record book when received, and is
given a serial number. For each contract a card is provided giving
information relative to the contract. On this card is also entered the
serial number of each sample of coal delivered under that contract.
After the samples are recorded, they are sent to the crushing room,
where they are reduced to the proper bulk and fineness for analysis.
They are then sent, in rubber-stoppered bottles, accompanied by blank
analysis report cards and card receipts, one for each sample, showing
the serial numbers, to the fuel laboratory for analysis. The receipt
card for each sample is signed and returned to the inspection office,
and when the analysis has been made, the analysis report card showing
the result is returned. This result is entered at once on the contract
card, and when all analyses have been received, covering the entire
delivery of coal, the average quality is calculated, and the results are
reported to the proper department.
The matter of supplying the Pittsburg plant with fuel for test purposes
is also carried on from the Washington office. Preliminary to a series
of investigations, the kinds and amounts of coal required are decided
on, and the localities from which these coals are to be obtained are
determined. Negotiations are then opened with the mine owners, who, in
most cases, generously donate the coal. When the preliminaries have been
arranged, an inspector is sent to the mine to supervise the loading and
shipment of the coal. This inspector enters the mine and takes, for
chemical analysis, small mine samples which are sent to the laboratory
at Pittsburg in metal cans by mail, accompanied by proper identification
cards. The results of the analysis are furnished to the experts in
charge at the testing plant, for their information and guidance in the
investigations for which the coal was shipped.
All samples for testing purposes are designated consecutively in the
order of shipment, “Pittsburg No. 1,” “Pittsburg No. 2,” etc. A complete
record of all shipments is kept on card forms at the Pittsburg plant,
and a duplicate set of these is on file in the inspection office at
Washington.
_Analysis of Fuels._--The routine analyses of fuel used in the
combustion tests at Pittsburg, and of the gases resulting from
combustion or from explosions in the testing galleries, or sampled in
the mines, are made in Building No. 21.[12] A small laboratory is also
maintained on the second floor of the south end of Building No. 13, for
analyses of gases resulting from combustion in the producer-gas plant,
and from explosions in Galleries Nos. 1 and 2, etc. From four to six
chemists are continually employed in this laboratory (in 8-hour shifts),
during prolonged gas-producer tests, and three chemists are also
employed in analyzing gases relating to mine explosions.
In addition to these gas analyses, there are also made in the main
laboratory, analyses and calorific tests of all coal samples collected
by the Geological Survey in connection with its land-classification work
on the coal lands of the Western States. Routine analyses of mine, car,
and furnace samples of fuels for testing, before and after washing and
briquetting, before coking and the resultant coke, and extraction
analyses of binders for briquettes, etc., are also made in this
laboratory.
The fuel-testing laboratory at Washington is equipped with three Mahler
bomb calorimeters and the necessary balances and chemical equipment
required in the proximate analysis of coal. More than 650 deliveries of
coal are sampled each month for tests, representing 50,000 tons
purchased per month, besides daily deliveries, on ship-board, of 550,000
tons of coal for the Panama Railroad. The data obtained by these tests
furnish the basis for payment. The tests cover deliveries of coal to the
forty odd bureaus, and to the District Municipal buildings in
Washington; to the arsenals at Watertown, Mass., Frankford, Pa., and
Rock Island, Ill.; and to a number of navy yards, through the Bureau of
Yards and Docks; to military posts in various parts of the country; for
the Quartermaster-General’s Department; to the Reclamation Service; to
Indian Agencies and Soldiers’ Homes; to several lighthouse districts;
and to the superintendents of the various public buildings throughout
the United States, through the Treasury Department; etc. During 1909,
the average rate of reporting fuel samples was 540 per month, requiring,
on an average, six determinations per sample, or about 3,240
determinations per month.
_Fuel-Research Laboratories._--Smaller laboratories, occupying, on the
average, three rooms each, are located in Building No. 21. One is used
for chemical investigations and calorific tests of petroleum collected
from the various oil fields of the United States; another is used for
investigations relative to the extraction of coal and the rapidity of
oxidization of coals by standard solutions of oxidizing agents; and
another is occupied with investigations into the destructive
distillation of coal. The researches under way show the wide variation
in chemical composition and calorific value of the various crude oils,
indicate the possibility of the extraction of coal constituents by
solvents, and point to important results relative to the equilibrium of
gases at high temperatures in furnaces and gas producers. The
investigations also bear directly on the coking processes, especially
the by-product process, as showing the varying proportion of each of the
volatile products derivable from types of coals occurring in the various
coal fields of the United States, the time and temperature at which
these distillates are given off, the variation in quality and quantity
of the products, according to the conditions of temperature, and, in
addition, explain the deterioration of coals in storage, etc.
[Illustration: Fig. 11.
PLAN OF CONSTRUCTION DETAILS OF METAL HOOD]
At the Washington office, microscopic investigations into the life
history of coal, lignite, and peat are being conducted. These
investigations have already progressed far enough to admit of the
identification of some of the botanical constituents of the older peats
and the younger lignites, and it is believed that the origin of the
older lignites, and even of some of the more recent bituminous coals,
may be developed through this examination.
In the chemical laboratories, in Building No. 21, the hoods (Figs. 11
and 12) are of iron, with a brick pan underneath. They are supported on
iron pipes, as are most of the other fixtures in the laboratories in
this building. The hood proper is of japanned, pressed-iron plate, No.
22 gauge, the same material being used for the boxes, slides, and bottom
surrounding the hood. The sash is hung on red copper pulleys, and the
corners of the hood are reinforced with pressed, japanned, riveted plate
to which the ventilating pipe is riveted.
[Illustration: Fig. 12.
ELEVATION OF CONSTRUCTION DETAILS OF METAL HOOD]
There is some variety in the cupboards and tables provided in the
various laboratories, but, in general, they follow the design shown in
Fig. 13. The table tops, 12 ft. long, are of clear maple in full-length
pieces, ⅞ in. thick and 2⅝ in. wide, laid on edge and drilled at
18-in. intervals for bolts. These pieces are glued and drawn together by
the bolts, the heads of which are countersunk. The tops, planed off,
sanded, and rounded, are supported on pipe legs and frames of 1¼ by
1½-in. galvanized-iron pipe with screw flanges fitting to the floor and
top. Under the tops are drawers and above them re-agent shelves. Halfway
between the table top and the floor is a wire shelf of a frame-work of
No. 2 wire interlaced with No. 12 weave of ⅝-in. square mesh.
Certain of the tables used in the laboratory are fitted with cupboards
beneath and with drawers, and, in place of re-agent stands,
porcelain-lined sinks are sunk into them. These tables follow, in
general style and construction, the re-agent tables. The tables used in
connection with calorimeter determinations are illustrated in Fig. 14.
The sinks provided throughout these laboratories are of standard
porcelain enamel, rolled rim, 18 by 13 in., with enameled back, over a
sink and drain board, 24 in. long on the left side, though there are
variations from this type in some instances.
The plumbing includes separate lines of pipe to each hood and table; one
each for cold water, steam at from 5 to 10 lb. pressure, compressed air,
natural gas, and, in some cases, live steam at a pressure of 60 lb.
On each table is an exposed drainage system of 2½-in. galvanized-iron
pipe, in the upper surface of which holes have been bored, through which
the various apparatus drain by means of flexible connections of glass or
rubber. These pipes and the sinks, etc., discharge into main drains,
hung to the ceiling of the floor beneath. These drains are of wood,
asphaltum coated, with an inside diameter ranging from 3 to 6 in., and
at the proper grades to secure free discharge. These wooden drain-pipes
are made in short lengths, strengthened by a spiral wrapping of metal
bands, and are tested to a pressure of 40 lb. per sq. in. Angles are
turned and branches connected in 4- and 6-in. square headers.
[Illustration: Fig. 13.
PLAN OF CONSTRUCTION DETAILS OF REAGENT TABLES BUILDING 21.]
[Illustration: Fig. 14.
CONSTRUCTION DETAILS OF CALORIMETER TABLES]
The entire building is ventilated by a force or blower fan in the
basement, and by an exhaust fan in the attic with sufficient capacity to
insure complete renewal of air in each laboratory once in 20 min.
The blower fan is placed in the center of the building, on the ground
floor, and is 100 in. in diameter. Its capacity is about 30,000 cu. ft.
of air per min., and it forces the air, through a series of pipes, into
registers placed in each of the laboratories.
The exhaust fan, in the center of the attic, is run at 550 rev. per
min., and has a capacity of 22,600 cu. ft. of air per min. It draws the
air from each of the rooms below, as well as from the hoods, through a
main pipe, 48 in. in diameter.
_Steaming and Combustion Tests._--The investigations included under the
term, fuel efficiency, relate to the utilization of the various types of
fuels found in the coal and oil fields, and deal primarily with the
combustion of such fuels in gas producers, in the furnaces of steam
boilers, in locomotives, etc., and with the efficiency and utilization
of petroleum, kerosene, gasoline, etc., in internal-combustion engines.
This work is under the general direction of Mr. R. L. Fernald, and is
conducted principally in Buildings Nos. 13 (Plate XVII) and 21.
For tests of combustion of fuels purchased by the Government, the
equipment consists of two Heine, water-tube boilers, each of 210 h.p.,
set in Building No. 13. One of these boilers is equipped with a Jones
underfeed stoker, and is baffled in the regular way. At four points in
the setting, large pipes have been built into the brick wall, to permit
making observations on the temperature of the gas, and to take samples
of the gas for chemical analysis.
The other boiler is set with a plain hand-fired grate. It is baffled to
give an extra passage for the gases (Fig. 15). Through the side of this
boiler, at the rear end, the gases from the long combustion chamber
(Plate XVIII) enter and take the same course as those from the
hand-fired grate. Both the hand-fired grate and the long combustion
chamber may be operated at the same time, but it is expected that
usually only one will be in operation. A forced-draft fan has been
installed at one side of the hand-fired boiler, to provide air pressure
when coal is being burned at high capacity. This fan is also connected
in such a way as to furnish air for the long combustion chamber when
desired. A more complete description of the boilers may be found in
Professional Paper No. 48, and Bulletin No. 325 of the U.S. Geological
Survey, in which the water-measuring apparatus is also described.[13]
On account of the distance from Building No. 21 to the main group of
buildings, it was considered inadvisable to attempt to furnish steam
from Building No. 13 to Building No. 21, either for heating or power
purposes. In view, moreover, of the necessity of installing various
types and sizes of house-heating boilers, on account of tests to be made
thereon in connection with these investigations, it was decided to
install these boilers in the lower floor of Building No. 21, where they
could be utilized, not only in making the necessary tests, but in
furnishing heat and steam for the building and the chemical laboratories
therein.
[Illustration: Fig. 15.
SETTING FOR 210-HORSE POWER, HAND-FIRED BOILERS]
In addition to the physical laboratory on the lower floor of Building
No. 21, and the house-heating boiler plant with the necessary coal
storage, there are rooms devoted to the storage of heavy supplies,
samples of fuels and oils, and miscellaneous commercial apparatus. One
room is occupied by the ventilating fan and one is used for the
necessary crushers, rolls, sizing screens, etc., required in connection
with the sampling of coal prior to analysis.
The Quartermaster’s Department having expressed a wish that tests be
made of the heating value and efficiency of the various fuels offered
that Department, in connection with the heating of military posts
throughout the country, three house-heating boilers were procured which
represent, in a general way, the types and sizes used in a medium-sized
hospital or other similar building, and in smaller residences (Fig. 2,
Plate XVI). The larger apparatus is a horizontal return-tubular boiler,
60 in. in diameter, 16 ft. long, and having fifty-four 4-in. tubes.[14]
In order to determine whether such a boiler may be operated under
heating conditions without making smoke, when burning various kinds of
coal, it has been installed in accordance with accepted ideas regarding
the prevention of smoke. A fire-brick arch extends over the entire grate
surface and past the bridge wall. A baffle wall has been built in the
combustion chamber, which compels the gases to pass downward and to
divide through two openings before they reach the boiler shell.
Provision has been made for the admission of air at the front of the
furnace, underneath the arch, and at the rear end of the bridge wall,
thus furnishing air both above and below the fire. It is not expected
that all coals can be burned without smoke in this furnace, but it is
desirable to determine under what conditions some kinds of coals may be
burned without objectionable smoke.[15]
For sampling the gases in the smokebox of the horizontal return-tubular
boiler, a special flue-gas sampler was designed, in order to obtain a
composite sample of the gases escaping from the boiler.
The other heaters are two cast-iron house-heating boilers. One can
supply 400 sq. ft. of radiation and the other about 4,000 sq. ft. They
were installed primarily for the purpose of testing coals to determine
their relative value when burned for heating purposes. They are piped to
a specially designed separator, and from this to a pressure-reducing
valve. Beyond this valve an orifice allows the steam to escape into the
regular heating mains. This arrangement makes it possible to maintain a
practically constant load on the boilers.
[Illustration: PLATE XVIII.
Fig. 1.--Long Combustion Chamber.
Fig. 2.--Gas Sampling Apparatus, Long Combustion Chamber.]
There is a fourth boiler, designed and built for testing purposes by the
Quartermaster’s Department. This is a tubular boiler designed on the
lines of a house-heating boiler, but for use as a calorimeter to
determine the relative heat value of different fuels reduced to the
basis of a standard cord of oak wood.
A series of research tests on the processes of combustion is being
conducted in Building No. 13, by Mr. Henry Kreisinger. These tests are
being made chiefly in a long combustion chamber (Figs. 16 and 17, and
Figs. 1 and 2, Plate XVIII), which is fed with coal from a Murphy
mechanical stoker, and discharges the hot gases at the rear end of the
combustion chamber, into the hand-fired Heine boiler. The walls and roof
of this chamber are double; the inner wall is 9 in. thick, of
fire-brick; the outer one is 8 in. thick, and is faced with red pressed
brick. Between the walls of the sides there is a 2-in. air space, and
between them on the roof a 1-in. layer of asbestos paste is placed. The
inner walls and roof have three special slip-joints, to allow for
expansion. The floor is of concrete, protected by a 1½-in. layer of
asbestos board, which in turn is covered by a 3-in. layer of earth; on
top of this earth there is a 4-in. layer of fire-brick (not shown in the
drawings).
[Illustration: Fig. 16.
CROSS-SECTIONS OF CHAMBER AND OF FURNACE, LONG COMBUSTION CHAMBER]
Inasmuch as one of the first problems to be attacked will be the
determination of the length of travel and the time required to complete
combustion in a flame in which the lines of stream flow are nearly
parallel, great care was taken to make the inner surfaces of the tunnel
smooth, and all corners and hollows are rounded out in the direction of
travel of the gases.
Provision is made, by large peep-holes in the sides, and by smaller
sampling holes in the top, for observing the fuel bed at several points
and also the flame at 5-ft. intervals along the tunnel. Temperatures and
gas samples are taken simultaneously at a number of points through these
holes, so as to determine, if possible, the progress of combustion
(Fig. 1, Plate XVIII).
About twenty thermo-couples are embedded in the walls, roof, and floor,
some within 1 in. of the inside edge of the tunnel walls, and some in
the red pressed brick near the outer surface, the object of which is to
procure data on heat conduction through well-built brick walls[16] (Fig.
2, Plate XVIII).
In order to minimize the leakage of air through the brickwork, the
furnace and tunnel are kept as nearly as possible at atmospheric
pressure by the combined use of pressure and exhausting fans.
Nevertheless, the leakage is determined periodically as accurately as
possible.
At first a number of tests w
Showing first 200,000 characters. Full text: gutenberg.org/ebooks/18448