
Gutenberg · ebook 17783
The Traveling Engineers' Association to Improve the Locomotive Engine Service of American Railroads
by Traveling Engineers' Association · English · public domain in the US
The Traveling Engineers' Association to Improve the Locomotive Engine Service of American Railroads by Traveling Engineers' Association is an English public-domain text held from Project Gutenberg (ebook #17783). To Improve The Locomotive
EXAMINATION QUESTIONS AND ANSWERS
For Firemen for Promotion and New Men for Employment :-:
Copyrighted by W. O. Thompson, March, 1911 Revised January, 1919
- * * * *
=PREFACE=
It is the policy of railroads to employ firemen who will in time become competent locomotive engineers. This requires that a man should have at least a common school education, good habits and be in good physical condition. He should be alert, with good reasoning faculties and a man of sound judgment. Having these qualifications, advancement will come to those who are conscientious in discharging their duties and who devote some of their leisure hours to study.
As an aid to this end, and that the railroad companies may derive the highest efficiency from the man employed as a locomotive engineman, a code of questions is given him, and it is expected that the preparation necessary to correctly answer the questions will indicate how well he has progressed.
The list of questions is also intended as a guide to the matters on which he should be correctly informed, both during his term of service as a fireman and for future promotion to engineer.
When a man is first employed as a fireman he will be given a list of questions on which he will be examined at the end of the first year; having passed this examination successfully he will then be given the examination questions for the following year; having passed this examination satisfactorily, he will be given a third and final set of examination questions on which he will be examined before being promoted to engineer. All these examinations will be both written and oral. The third year examination for promotion will be before the General Board of Examiners.
At any of these examinations, if he fails to pass 80 per cent. of the questions asked, another trial, not less than two months and not more than six months later, will be given him to pass the same examination; if he fails to pass by a percentage of 80 per cent. he shall be dropped from the service.
Where the examinations consist of both air brake and machinery, the candidate must pass 80 per cent. in each to be successful.
Firemen passing the third and final series of questions will be promoted in the order of their seniority as firemen, except that those who pass on the first trials shall rank, when promoted, above those who passed on the second trials.
Engineers employed who have had service on other roads, will be required to pass the third series of questions before entering the service.
It is not expected that the man will pass these examinations without assistance, and in order that he will understand the use of locomotive and air brake appliances properly, he is expected to go to the Master Mechanic, General Foreman, Road Foreman or Traveling Engineer, also Air Brake Inspector or Instructor, or any other official, and ask them for such information as may be required on any of the questions or on any points in connection with the work.
He is not only invited, but also urged to do this, as the more knowledge of his business a man possesses, the better will be the results obtained. He will have ample time to study each set of questions; there is no doubt that with a reasonable amount of study each week, supplemented with close observation of the working of the locomotive, the information necessary to answer satisfactorily the entire list of questions can be easily mastered in the time given.
In regard to breakdowns, it is advised that he carefully inspect each breakdown or disabled engine that comes to his notice, see where the parts have given way and in what manner the work of blocking up it done. It is not expected that all the breakdowns which may happen to a locomotive will occur on the engine that he is with; therefore it is good practice to observe how other men care for these breakdowns.
In connection with these examinations the work done by the fireman during the year and how the work compares with that of other firemen in the same class of service will be carefully noted; his record as to the use of coal, supplies and attention to duty will be taken into consideration.
It is hoped that he will give everything in detail the consideration it merits and realize fully that it is by looking after the little things that a man succeeds. It should be borne in mind that by filling well the position he holds he becomes entitled to the confidence that makes better positions possible. It is understood that those who conduct the examination may ask any question or questions bearing on any subject of this examination, in order to determine how well the persons being examined understands the subject. A mere memorized answer will not be sufficient. The full meaning of each answer must be understood.
=EXAMINATION QUESTIONS=
FIRST SERIES
- Q. What do you consider essential for your success in regard to the
use of fuel A. I deem it essential to my success to be as economical in the use of fuel and supplies as is consistent with the work to be performed, exercising good judgment in my work, harmonious co-operation with my engineer, and showing a willingness to learn and practice the best methods in my work.
- Q. What are the fireman's duties on arrival at enginehouse previous
to going out on a locomotive?
A. He is required to examine the bulletin board, guards on water and lubricator glasses; try gauge cocks to find true water level; then examine grates, ash-pan, flues and fire-box. Put fire in proper shape; see that a proper supply of firing tools, water, coal, oil and waste are provided, that all lamps and markers are filled, cleaned and in proper condition; and to perform such other duties as may be required by the engineer to assist him in getting the engine in readiness.
- Q. What pressure is indicated by the steam gauge? What is meant by
atmospheric pressure?
A. The pressure per square inch inside of the boiler. Atmospheric pressure is the pressure represented by the density of the atmosphere in pounds per square inch, which is at sea level 14.7 pounds.
- Q. On what principle does a steam gauge work?
A. The steam gauge pointer is actuated by a flattened or bent round tube to straighten itself under the pressure of steam against the water inside of tube. The gauge pointer receives movement from suitable mechanism connected with the tube.
- Q. What is the source of power in a steam locomotive?
A. Heat is the source of power in all steam engines. It is necessary to have fuel and water. When fuel is burned, the water coming in contact with the hot sheets evaporates and becomes steam, which is then used in the cylinders to force the pistons back and forth.
- Q. About what quantity of water should be evaporated in a locomotive
boiler to the pound of coal?
A. From five to seven pounds of water. For example, one gallon of water weighs eight and one-third pounds, therefore 100 pounds of coal should evaporate from sixty to eighty-four gallons of water.
- Q. What is steam, and how is it generated?
A. Steam is water in the condition of a vapor and is generated by heating the water above the boiling point.
- Q. What is the purpose of the water gauge glass and gauge cocks?
A. To indicate the level of water in the boiler.
- Q. What would indicate to you that the boiler connections of water
gauge glasses were becoming clogged?
A. The up and down movement of the water in the glass would become slow and inactive, or it would not register correctly with the gauge cocks.
- Q. At what temperature does water boil?
A. At atmospheric pressure, which is 14.7 pounds at sea level, water boils at 212 degrees Fahrenheit; the temperature, however, increases as the pressure under which the water is boiled increases. At 200 pounds boiler pressure the temperature would be 388 degrees Fahrenheit.
- Q. What is carbon?
A. Carbon forms the greatest part of all kinds of coal; the higher the per cent. of carbon, the higher the grade of coal.
- Q. What is the composition of bituminous coal?
A. It is composed of carbon about 75 per cent. and many gaseous substances, as is shown by its burning with a large flame and much smoke. Anthracite, on the contrary, is nearly pure carbon and burns with a small flame.
- Q. What is combustion?
A. Combustion or burning is a chemical process, it is the action of fire on inflammable substances and is the union of the oxygen in the air with the carbon in the fuel; this is called rapid combustion. Slow combustion is the decaying of wood or iron by the elements.
- Q. Is air necessary for combustion?
A. Yes.
- Q. About how many cubic feet of air is necessary for the combustion
of a pound of coal in a locomotive fire-box?
A. About 300 cubic feet of air must pass through the grates and fire for complete combustion of one pound of coal.
- Q. Why must air be heated before combining with coal?
A. Air, like coal and its gases, must be heated before they will unite to form what is known as combustion and so as not to reduce the temperature of the fire-box below the igniting point of the gases.
- Q. Why is it necessary to provide for combustion a supply of air
through the fuel in the furnace?
A. In order to supply the oxygen necessary for combustion.
- Q. What is the effect upon combustion if too little air is supplied?
If too much air is supplied?
A. If too little air is supplied, combustion is not complete, and only one-third as much heat is obtained. If too much air is supplied, combustion is complete; but the excess air must be heated, resulting in a lower temperature. If twice the amount of air required for complete combustion be supplied, the temperature of the fire-box will be about one-half as high.
- Q. Give a practical definition of the igniting temperature.
A. In all ordinary combustion there is a definite temperature, called the ignition or kindling temperature, to which combustible substance must be heated in order that it may unite with the gas in supporting the combustion. The burning substance must not only be heated up to the kindling temperature, but it must be kept as high as this temperature, or combustion will cease.
- Q. State why such temperature is necessary and at what place in the
fire-box it is most required.
A. The center is the hottest part of the fire-box. There is a much lower temperature in the fire-box at the sides and end sheets, due to the water on the opposite sides of the sheets being of a lower temperature than the fire-box; therefore if we get as high a temperature as possible at the side and end sheets, we will increase the steam-making efficiency of the boiler. The gases which are liberated from the coal as soon as it becomes heated must attain a temperature of about 1,800 degrees Fahrenheit, known as the "temperature of ignition," before they will unite with air which must also be heated up to that point.
- Q. How is draft created through the fire?
A. Exhaust steam escaping through the stack reduces the pressure in the smoke-box below the pressure of the atmosphere outside, therefore the air tends to force itself into the smoke-box through all openings; with everything in good condition, the easiest and largest passage for it is through the grates and other openings into the fire-box and from it through the tubes into the smoke-box and up the stack.
- Q. Is smokeless firing practicable?
A. Yes, but it is necessary in order to obtain good results that boiler and fire-box be in good condition, coal broken to the proper firing size; then, with the hearty and intelligent co-operation of both engineer and fireman, smokeless firing is both economical and practicable.
- Q. In what condition should the fire be in order that the best
results may be obtained from the combustion of the coal?
A. The fire should be as light as the work being done by the engine will permit, evenly distributed over the grates and free from clinkers.
- Q. How should the blower be used?
A. A blower should be used very lightly, being careful not to draw too much air into the fire-box and through the flues, especially when fire is being cleaned or thin on grates.
- Q. What is the result of opening the fire-door when the engine is
working steam?
A. It will cause a cooling effect in the fire-box and is liable to start the flues leaking.
- Q. What is the effect of putting too many scoops of coal on a bright
fire? Is this a waste of fuel?
A. It has the effect of temporarily deadening and cooling the fire, causes emission of quantities of black smoke, as only a limited amount of gas can be burned in a fire-box at a time; all in excess of that amount escapes from the stack and is a waste of fuel.
- Q. What effect has the fire upon a scoopful of coal when it is
placed in the fire-box?
A. The heat from the fire drives the gases from the coal and they are ignited by the hot flame as they pass over the bright fire; the coke which is left burns where it is.
- Q. In what condition should the fire be to consume these gases?
A. A bright white coke fire, almost incandescent.
- Q. What is the temperature of the fire when in this condition?
A. It must not be less than 1,800 degrees Fahrenheit to consume the gases liberated from the coal, and it only requires from 750 to 900 degrees Fahrenheit to burn the coke that remains on the grate; as coke burns from the outside, less heat is required to consume it.
- Q. How can the fire be maintained in this condition?
A. By adding coal to the fire in small quantities, spreading it over the grate surface and no faster than it is burned.
- Q. What is black smoke? Is it combustible?
A. Black smoke consists of small particles of carbon suspended in the gases of combustion and indicates incomplete combustion. Black smoke is not combustible, it is like lampblack and cannot be burned after having been produced. The production of it can be prevented by suitable arrangements and manipulation.
- Q. Should the gas not burn in the fire-box, will it burn after it
enters the flues? Why?
A. Gas will not burn only a short distance in the flues of a boiler, as the water absorbs the heat so quickly that the temperature of gas is lowered below the igniting point.
- Q. What is the effect on the flow of air through the fire from
opening the door? What on the burning of the gases? What on the flues and sheets of the fire-box?
A. When the furnace door is opened, the flow of air through the grate is stopped in proportion to the amount that passes through the door. The vacuum will be filled from the quickest source and the door is closer than some parts of the grate. The gases mix with the air from the door and pass out through the flues; no combustion takes place, as the air is not hot enough to unite with the gas. The flues and sheets of the box will be caused to leak on account of the rapid contraction.
- Q. Can the firing be done more effectively if the water level is
observed closely?
A. Yes, in order to know how much water there is in the boiler and whether it is necessary to hurry the fire; if the boiler is full, it is possible to prevent the pops opening by delaying the fire.
- Q. How should the fire and water be handled in starting from a
terminal or other station?
A. The steam pressure should be near the maximum and there should be sufficient water in the boiler to last until such time as the fire is burning well so that the pressure will not be reduced when water is put into the boiler. There should be a moderately heavy bed of fire well burned and distributed evenly over the grates. After the fire is burning well, the injector should be started lightly; the feed being gradually increased so as not to cause any decrease of steam pressure.
- Q. What is the purpose of a safety valve on a locomotive boiler? Why
are more than one used?
A. A safety valve is used to limit the maximum pressure in the boiler by opening and allowing steam to escape. More than one safety valve are used as additional protection against excessive pressure; one is set at the maximum pressure and the others are set at two or three pounds above the maximum pressure.
- Q. What is usually the reason for steam being wasted from the safety
valve? What can be done to prevent this waste?
A. Careless firing, careless running. Both engineer and fireman work in harmony to obtain the best results.
- Q. What is the estimated waste of coal for each minute the safety
valve is open?
A. About fifteen pounds. The estimated waste of steam when an engine pops equals every second all the heat obtained from a quarter pound of coal. Safety valves usually remain open about half a minute, resulting in the loss of about eight pounds of coal.
- Q. What should be the condition of the fire on arriving at a station
where a stop is to be made?
A. On approaching the station where a stop is to be made, firing should be stopped far enough back to allow the carbon gases to be consumed before the throttle is closed, so there will be little or no black smoke from the stack and yet have sufficient fire that it will not be necessary to feed the fire again if a short stop is to be made until the train is started and the engine cut back or nearly to the running cut-off.
- Q. How should you build up the fire when at stations in order to
avoid black smoke?
A. Put in small quantities of coal at a time, have the door slightly open and have the blower on lightly; good judgment must be exercised by the fireman.
- Q. Why is it that if there is a thin fire with a hole in it the
steam pressure will fall at once?
A. Because too much cold air is drawn into the fire-box and through the tubes, retarding combustion and cooling the fire-box and tubes.
- Q. If the injector is to be used after throttle is shut off, how
should the fire be maintained?
A. A sufficient quantity of coal should be placed on the grates to maintain the maximum steam pressure and the blower used to keep the fire burning brightly.
- Q. What would be the result of starting a heavy train or allowing
drivers to slip with the fire too thin on the grates?
A. The fire would be pulled off the grates and into the tubes, leaving the fire bed full of holes and some of the fire remaining on the grates turned over. Large quantities of cold air would be drawn in, resulting in a rapid decrease of temperature and pressure. The tubes would possibly start leaking and the fire would be in such condition that it could not be built up properly in a long distance. Possibly the grates would become clogged up with green coal--an excellent opportunity for forming clinkers. In this condition, the engine would fail to make steam for the entire trip.
- Q. Where should the coal, as a rule, be placed in the fire-box?
A. As a rule, more coal is burned along the sides and in the corners than in the middle of the grates; the fire should consequently be kept somewhat heavier along the sides and corners than in the middle.
- Q. How is the fire affected by and what causes clinkers?
A. A clinker shuts off area of grate surface according to its size, and thereby shutting off that much of the air supply and interfering with proper combustion. Clinkers are caused by firing too heavy in spots, which prevents sufficient air passing up through these spots and allows the coal to run together, melting the ash, and sand; running a hoe or slash bar through the fire will bring the points of melted sand together, thereby causing a clinker.
- Q. How can you best avoid their formation and dispose of them?
A. Light firing and occasionally moving the grates lightly is the best preventive. When once formed, they should be removed if possible by firing around and burning them out.
- Q. How can you explain the slower burning of the coke and how
understand the proper manner of supplying fresh coal?
A. The gases of coal are lighter than air and will pass away whether consumed or not. The slow burning of the coke is due to the fact that it burns from the outside only. When a fire reaches a white or incandescent heat it indicates that the gases are burned and a fresh supply of coal should be added; this is to be done as light as the service performed by the engine will permit.
- Q. When and for what purpose is the use of a rake on the fire bed
allowable?
A. The rake should be used on the fire very seldom, because raking the fire bed tends to form clinkers, especially when the rake is plunged down through the fire to the grate. It may be used when necessary to rake the fire lightly when on the road for the purpose of breaking the crust, which may be found as a consequence of too heavy firing.
- Q. Within what limits may steam pressure be allowed to vary, and
why?
A. Pressure should not be allowed to vary more than five pounds from the maximum for the reason that too much expansion and contraction will take place, which many times is the cause of flues leaking, cracked or broken side sheets and stay bolts.
- Q. Has improper firing any tendency to cause the tubes to leak? How?
A. Yes; if the pressure is not regularly maintained, the fluctuations of temperature cause constant contraction and expansion to take place. If the fire is not carried level, but is carried heavy in some parts of the fire-box and light in others, holes will be worked in, cold air drawn through, lowering the temperature, chilling the tubes and causing leaks.
Carrying the fire too heavy in some places, causes clinkers to form. If the door is open too long, too much cold air is drawn over the fire, causing the tubes to leak.
- Q. What do you consider abuse of a boiler?
A. Careless or improperly supplying water to the boiler, improper firing or allowing steam to vary from high to low pressure, causing unnecessary expansion and contraction.
- Q. Does the stopping up of flues affect the steaming capacity of the
engine?
A. Yes; obstructed flues reduce the heating surface, reduce the steaming capacity of the engine, and, as a rule, result in causing the flues to leak. They also cause an increase of speed of the gases through the remaining flues and a poor steaming engine.
- Q. What causes honeycomb over the flues?
A. Honeycomb on flues is usually caused by the draft through the fire picking up the sulphur and molten clay which is in a molten and sticky condition in the fire; as it passes on its way to the stack, some of it strikes the flue-sheet and sticks or passes through the flues, clogging up the netting in the front end.
- Q. How would you take care of a boiler with leaky tubes or fire-box,
and why?
A. Keep a bright, clean fire, especially up next to the flue-sheet, and as even a pressure of steam as possible and not use the blower any stronger than is absolutely necessary.
- Q. Why is it very important that coal should be broken so that it
will not be larger than an ordinary sized apple before being put into the fire-box?
A. In order to get rapid and complete combustion, coal should be broken into small pieces; this aids combustion by exposing a larger surface to the flame and can be fired more economically and better results are obtained.
- Q. Should rapid firing be practiced?
A. No; it should not be practiced for the same reason that heavy firing is wrong. A few moments should intervene between each shovelful to allow the fresh coal to get to burning and to maintain the high temperature in the fire-box.
- Q. When and why should you wet the coal on the tender?
A. Coal should be wet for the purpose of cleanliness to keep dust from flying and because moderately wet coal gives out more heat for the reason that there is not so much fine coal drawn through the tubes. It should be wet as often as necessary to accomplish these purposes.
- Q. What are the advantages of a large grate surface?
A. Greater heating surface, lighter fire and more complete combustion are possible with the larger grate surface, because a larger amount is burning at one time at a slower rate of combustion.
- Q. Why are grates made to shake, and how, when and where should they
be shaken?
A. For the purpose of breaking any clinkers that might form and to shake out all refuse from the grates. The best time to shake grates is when throttle is closed, as there is no exhaust to carry the unconsumed gases and sulphur through the flues into the front end, which is liable to choke or clog up netting and cause a steam failure. Grates should not be shaken while passing over bridges, near lumber or hay yards or through prohibited territory.
- Q. Do you understand that coal furnished represents money invested,
and should be fired economically and not allowed to fall out of the gangway?
A. The fuel of locomotives is property and represents money invested the same as do buildings, rolling stock, etc.; careless or inefficient firemen who waste fuel destroy property as certainly as though cars or engines were smashed up. The coal should be carefully raked off the deck and in from the gangways; it should not be allowed to fall, as it is wasted and dangerous to people near the track. The deck should be kept clean for greater comfort and convenience.
- Q. Is is objectionable to fill the tanks too full of coal or
overflow tank at standpipes or water tanks?
A. It is. Tanks filled too full of coal are dangerous and a great waste of coal, as the jar when running will cause a part of it to fall off; water overflowing from tanks results in washing away the ballast and in cold weather freezes over the tracks.
- Q. What are the duties of a fireman on arrival at the terminal?
A. Different roads have different assigned duties for the firemen to perform. They should leave the cab, boiler head, oil cans and deck in a clean condition, boiler full of water, enough fire and steam, so that the hostler will not be required to put in fuel while the engine is in his charge; should know that throttle valve is securely closed, reverse lever in center of quadrant, cylinder cocks open, and if equipped with independent brake, it to be applied; in fact, it is an excellent opportunity for a mechanical officer to judge the ability of the fireman and future engineer.
- Q. Is the engineer responsible for the fireman's conduct while on
duty and for the manner in which the fireman's duties are performed?
A. He is. The fireman is under the direction of the engineer, and the fireman's duties are to be performed in accordance with the engineer's instructions.
- Q. What is the duty of the superheater damper, and how does it
operate?
A. The duty of the damper is to control the flow of gases through the large flues, thereby protecting the units which are contained therein from being overheated after throttle is closed. The position of damper when the engine is not working steam, is closed.
- Q. What will be the effect on the steaming of the engine if the
damper does not open properly?
A. Engine will steam poorly for the reason that there will be no draft through the large flues. The steam will not be superheated because heated gases cannot come in contact with superheated units contained in the large flues.
- Q. How may steam failure be avoided in case the damper fails to
operate?
A. The counterweight may be tied up, thereby opening the damper.
=AIR BRAKE QUESTIONS=
- Q. What is an air brake?
A. A brake operated by compressed air.
- Q. How is this air compressed?
A. By an air compressor on the locomotive.
- Q. Name the different parts of the air brake as applied to the
locomotive.
A. The air compressor, compressor governor, automatic and independent brake valves, distributing valve, triple valve, auxiliary reservoir, brake cylinders, main reservoir, air gauges, angle cocks, cut-out cocks and the necessary piping.
- Q. What is the purpose of the main reservoir?
A. It is used for storing a large volume of air for the purpose of promptly charging and recharging the brakes. Where the engine is equipped with either the E. T. or L. T. type of brakes, main reservoir air is used to supply the air to the brake cylinders on the locomotive.
- Q. What other appliances use main reservoir air?
A. It is used in the operation of the power reverse gear, sand blower, bell ringer, water scoop, air signal, fire door, water sprinkler and other devices.
- Q. What does the red hand on each of the air gauges indicate?
A. The red hand on the large gauge indicates main reservoir pressure; on the small gauge, brake cylinder pressure.
- Q. What does the black hand on each of the air gauges indicate?
A. The black hand on the large gauge indicates the equalizing reservoir pressure; on the small gauge, brake pipe pressure.
- Q. What pressure is usually carried in the main reservoir?
A. Ninety pounds in freight and 130 pounds in passenger service. But where freight engines are equipped with duplex compressor governor, the low pressure top is adjusted to ninety pounds and the high pressure top to 130 pounds.
- Q. What pressure is usually carried in the brake pipe?
A. Seventy pounds in freight and 110 pounds in passenger service.
- Q. What must the air pass through in flowing from the main reservoir
to the brake pipe?
A. Through the automatic brake valve.
- Q. Name the different positions of the automatic brake valve.
A. Release, running, lap, service and emergency positions. The brake valve used with the E. T. and L. T. equipment has still another position known as holding position, which is located between running and lap positions.
- Q. Name the different positions of the independent brake valve.
A. Release, running, lap, slow application and quick application positions.
- Q. How many kinds of triple valves are there in use?
A. Two; plain and quick action.
- Q. How is the automatic brake applied? How released?
A. The automatic brake is applied by a reduction of brake pipe pressure, and is released by restoring the brake pipe pressure.
- Q. When the independent brake valve handle is placed in application
position, are the train brakes affected?
A. No; only the brakes on the locomotive are applied.
- Q. What controls the pressure in the main reservoir?
A. The compressor governor.
=EXAMINATION QUESTIONS=
SECOND SERIES
- Q. What, in your opinion, is the best way to fire a locomotive?
A. To carry a nice, level fire on the grate, or it may be just a little heavier at the sides and front, so the air cannot come through it near the sheets as rapidly as in the center of the fire-box; always fire as light as consistent with the work required, endeavor to maintain a uniform steam pressure at all times, and avoid unnecessary black smoke and a waste of steam through the safety valves by the engine popping.
- Q. What are the advantages of superheated steam over saturated steam
in locomotive service?
A. Saving in water; saving in fuel; increased boiler capacity and a more powerful locomotive. Superheated steam does away entirely with all condensation in the cylinders, while saturated steam coming in contact with passages in cylinder saddle and walls of cylinders, is immediately cooled and in cooling, a part of it is changed back into water which affects the pressure and therefore its capacity to do work.
- Q. How is the saving in water produced?
A. By the elimination of all cylinder condensation present in saturated steam locomotives and the increase in volume of a given weight of steam.
- Q. How is the saving in coal accomplished?
A. Because there is less steam used to do the same amount of work, there is less water evaporated and consequently less coal required to evaporate the water.
- Q. How is the increased boiler capacity obtained?
A. A boiler will evaporate a certain amount of water into steam and if part of the steam is lost by condensation, only that remaining is available for running the engine. Superheating eliminates the losses, thereby increasing the available useful steam. Further, superheating increases the volume of a given weight of steam, thereby reducing the consumption of steam required to develop a certain power and consequently increases the capacity.
- Q. How is a more powerful engine obtained?
A. By reason of the increased boiler capacity an engine may be worked farther down before a steam failure occurs.
- Q. What type of fire tube superheater is in most general use in
locomotive service?
A. The top header fire tube type, known as the "Schmidt Superheater." A system of units located in large flues through which the steam passes on its way from the dry pipe to the steam pipes, and a damper mechanism which controls the flow of gases through the large flues.
- Q. Describe the construction and location of the header.
A. The header is a simple casting, divided by partition walls into saturated and superheated steam passages. It is located between the dry pipe and the steam pipes, the same as the nigger head in a saturated locomotive. The dry pipe is in communication with the saturated steam passages and the steam pipes with the superheated steam passages and these are in communication with each other through the superheated units.
- Q. Describe the construction of superheater units and their
connection to the header.
A. The units are composed of four seamless steel pipes, connected by three return bends. Of the four pipes, two are straight and two are bent upward and connected to the header by means of a clamp and bolt; one end of the unit is in communication with the saturated steam passage and the other with the superheated steam passage in the header casting.
- Q. Trace the flow of steam through the top header fire tube
superheater.
A. When the engine throttle is open, saturated steam passes through the dry pipe into the saturated steam passage of the header casting. From this passage it enters one end of the unit, passing backward toward the fire-box, forward through one of the straight pipes and the front return bend, backward through the other straight pipe to the back return bend, and forward through the bent pipe and upward into the superheater steam passage of the header, from which it enters the steam pipes and is carried to the steam chest.
- Q. What should be the position of throttle valve when running a
superheater locomotive?
A. The engine should always be run with as wide open throttle as the conditions will permit, regulating the steam admission to the cylinders according to work to be performed.
- Q. What should be the position of throttle while drifting?
A. The throttle valve should be kept slightly open while drifting, so as to admit a small quantity of steam in valve chamber and cylinder above atmospheric pressure, to prevent the inrush of hot air and gases which destroy lubrication, also to prevent excessive wear to valve, cylinder and piston rod packing.
- Q. How should the water be carried in boiler of superheater
locomotives?
A. As low as the conditions will permit, because this practice reduces the tendency to work water over into the dry pipe and units, as the superheater locomotive will use one-third less water than the saturated locomotive.
- Q. What care should be exercised in lubricating a superheater
locomotive?
A. The supply of oil to steam chest should be watched very closely by the engineer, he to know that lubricator is feeding constantly and evenly over entire division, and according to work performed.
- Q. Describe the general form of a locomotive boiler.
A. A locomotive boiler is cylindrical in form, it usually has a rectangular shaped fire-box at one end and a smoke-box at the other, and flues extend through the cylindrical part, and, like the fire-box, are surrounded by water.
- Q. How does the wide fire-box type of boiler differ from the
ordinary boiler, and what are its advantages?
A. The wide fire-box type of boiler is built so the fire-box is above the frame and extends out over the driving wheels. The advantages of this are to obtain a larger grate area in the same length of fire-box and to give a slower rate of combustion per square foot of grate surface. The deep fire-box is limited in width to the distance between the frames, while the shallow fire-box sets on top of the frames and between the driving wheels.
- Q. Why have two fire-box doors been placed in the large type of
locomotive boilers?
A. For convenience of the fireman on account of the greater width of the fire-box, so that coal can easily be distributed to all parts of the fire-box.
- Q. Describe a locomotive fire-box.
A. The modern form is a rectangular shaped structure located at the back end of the boiler. It has a door and is composed of two side sheets, a crown sheet, a back sheet and a flue sheet from which the flues extend to the smoke-box at the other end of the boiler.
- Q. To what strains is a fire-box subjected?
A. To crushing strains and to those of unequal contraction and expansion.
- Q. How are the sheets of a fire-box supported?
A. They are supported by staybolts screwed through the inside and outside sheets with their ends riveted over.
- Q. In what manner is a crown sheet supported?
A. By crown bars or radial staybolts.
- Q. What are the bad features about crown bars?
A. They are hard to keep clean and frequently cause crown sheets to become mud burned.
- Q. What are the advantages of radial stayed crown sheets?
A. They are easier to keep clean and cheaper to repair.
- Q. How are the inside and outside sheets of a fire-box secured at
the bottom?
A. They are riveted to a wrought iron ring called a mud-ring.
- Q. Describe the ash-pan and its use.
A. It is a receptacle secured to the fire-box and usually provided with dampers to regulate the flow of air to the fire. It collects the ashes that drop from the fire-box and prevents them from setting fire to bridges or other property along the track. Engine-men must know that ash-pan slide and hopper bottoms are closed before leaving enginehouse.
- Q. What is a "wagon-top" boiler?
A. It is a boiler that has the fire-box end made larger than the cylindrical part to provide more steam space.
- Q. Why are boilers provided with steam domes?
A. To furnish more steam space and to obtain dryer steam and to provide a place for the safety valves, steam pipes, throttle valve and whistle.
- Q. What must be the condition of a boiler to give the best results?
A. It must have good circulation and be clean and free from mud or scale.
- Q. What is meant by "circulation" in a boiler?
A. Free movement of the water, so that it may come in contact with the heating surface and after being converted into steam be immediately replaced by a fresh supply of water.
- Q. What would be the effect if a "leg" of the fire-box became filled
with mud?
A. There would be no water in contact with the fire-box sheets and they would quickly become overheated and mud-burned.
- Q. What would be the result if the fire-box sheets became
overheated?
A. They would be weakened and forced off the staybolts and an explosion would occur.
- Q. Would it be advisable to put water into a boiler after the sheets
had become bare and red hot?
A. No. The fire should be killed at once.
- Q. What effect has the stoppage of a large number of flues?
A. The heating surface and draft are decreased by just that much area.
- Q. Why are boiler checks placed so far away from the fire-box?
A. To introduce the water into the boiler at as great a distance from the fire-box as possible. This permits the water to become heated to a high temperature before it comes in contact with the fire-box and also improves circulation.
- Q. What part of the boiler has the greatest pressure? Why?
A. The bottom, because it is subject to the weight of the water in addition to the steam pressure in the boiler.
- Q. What are the advantages of the extension front end?
A. To provide room for suitable draft and spark appliances.
- Q. What is the purpose of a netting in a smoke-box or front end?
A. To act as a crusher of all cinders and prevent large cinders from passing out of the front end to the atmosphere.
- Q. What is the object of hollow staybolts?
A. To indicate when the staybolt is broken by the escape of steam through the small hole in the bolt.
- Q. What will cause the engine to tear holes in the fire?
A. Working hard or slipping when the dampers are open and the door closed, or too thin a fire.
- Q. Name the various adjustable appliances in the front end by which
the draft may be regulated.
A. The exhaust nozzle, the diaphragm and the draft pipes or petticoat pipe.
- Q. What object is there in having the exhaust steam go through the
stack?
A. To create a draft through the tubes and fire-box.
- Q. How does this affect the fire?
A. The exhaust steam escaping through the stack tends to empty the smoke-box of gases and produces a partial vacuum there, atmospheric pressure then forces air through the grates and tubes to refill the smoke-box, and in this way the draft through the fire is established and maintained.
- Q. Explain what adjustments can be made and the effect of each
adjustment on the fire.
A. Larger or smaller nozzle tips cause less or greater draft on the fire; raising or lowering the draft pipes and diaphragm causes the engine to burn the fire more at the rear or front end of the fire-box; the size and position of the draft pipes increase the draft through the top or bottom flues; the latter adjustments should always be attempted before reducing the nozzle.
- Q. What does it indicate when the exhaust issues strongest from one
side of the stack?
A. The stack, exhaust pipe or petticoat pipe are out of plumb.
- Q. What is the effect of leaky steam pipe joints inside the
smoke-box?
A. The engine will not steam freely.
- Q. What causes "pull" on the fire-box door?
A. The partial vacuum in the front end; when excessive it indicates dampers closed, fire clinkered or insufficient opening for the admission of air under the fire.
- Q. If upon opening the fire-box door you discover there what is
commonly called a red fire, what might be the cause?
A. The grates may have become clogged with ashes or clinkers so that sufficient air could not pass through them to the fire.
- Q. Is it not a waste of fuel to open the fire-box door to prevent
pops from opening? How can this be prevented more economically?
A. Yes. This can usually be prevented by putting the heater into the tank, or putting on the injector, or by more careful firing.
- Q. Describe the principle upon which the injector works.
A. The action of the injector is due first to the difference between "kinetic" or moving energy and "static" or standing energy; second, to the fact that steam at a pressure travels at a very high velocity and when placed in contact with a stream of water it is condensed into water, and at the same time it imparts enough velocity to the water to give it sufficient momentum to overcome a pressure even greater than the original pressure of the steam. By imparting this velocity to the water it gives it sufficient energy to throw open the check valves and enter the boiler against high pressure.
- Q. What is the difference between a lifting and a non-lifting
injector?
A. A lifting injector will create sufficient vacuum to raise the water from the level of the tank. The steam tubes in a non-lifting injector are different and it will not raise the water, but merely force it into the boiler. A non-lifting injector must be placed below the level of the water in the tank so the water will flow to it by gravity.
- Q. Will an injector work with a leak between the injector and tank?
Why? Will it prime?
A. A lifting injector will not work if the leak is bad. It will not prime because the air admitted through the leak destroys the vacuum necessary to raise the water to the injector level. A non-lifting injector will work, as the water will escape from the pipe instead of air being drawn into it as with the lifting injector.
- Q. If it primes well, but breaks when the steam is turned on wide,
where would you look for the trouble?
A. Insufficient water supply due to tank valve partly closed, strainer stopped up or tank hose kinked, injector tubes out of line, limed up, or delivery tube cut, or wet steam from the throttle.
- Q. If it would not prime, where would you expect to find the
trouble?
A. Insufficient water supply, priming valve out of order, or with the lifting injector the trouble might be caused by a leak between the injector and tank.
- Q. Will an injector prime if the boiler check leaks badly or if it
is stuck up? If the injector throttle leaks badly?
A. No.
- Q. If steam or water shows at the overflow pipe when the injector is
not working, how can you tell whether it comes from the boiler check or the injector throttle?
A. Close the main steam valve at the boiler, that will stop the leak if it comes from the injector throttle.
- Q. Will an injector prime if primer valve leaks? Will that prevent
its working?
A. It will prime, but not as readily as with priming valve in good condition. This will not prevent its working, but it may waste some water from the overflow.
- Q. Will an injector work if air cannot get into the tank as fast as
the water is taken out?
A. No.
- Q. If you had to take down a tank hose, how would you stop the water
from flowing out of the tank that has the syphon connections instead of the old-style tank valves?
A. Open the pet cock at the top of the syphon before taking the hose down.
- Q. Is any more water used when the engine foams than when the water
is solid?
A. Yes, very much more.
- Q. How would you prevent injector feed pipes or tank hose from
freezing in winter when not in use?
A. The steam valve should be slightly open to permit a slight circulation of steam through the feed and branch pipes. The heater cock should be closed and the drip cock under the boiler check or on the branch pipe should be opened to insure a circulation of steam through the branch pipe.
- Q. How would you prevent the overflow pipe from freezing with a
lifting injector?
A. The overflow valve should be opened just enough to permit a little steam to escape through the overflow pipe to prevent it from freezing.
- Q. Name the various parts of the injector.
A. The injector consists of a body supplied with a steam valve, a steam nozzle, a primer, a combining tube, a delivery tube, a line check valve, an overflow valve, a water valve, and a lifting injector has a lifting tube.
- Q. What may be done if a combining tube is obstructed?
A. The steam valve bonnet may be removed and the obstruction forced out with a piece of stiff wire, or uncouple the delivery pipe from the injector and unscrew and remove the tubes; the obstruction can then be removed and the tubes replaced.
- Q. How is the greatest injury done to a boiler when cleaning or
knocking the fire?
A. By excessive use of the blower drawing cold air through the fire-box and flues.
- Q. Why does putting a large quantity of cold water into a boiler
when the throttle is closed cause the flues to leak? When is this most serious?
A. When steam is not being used there is not much circulation of water in the boiler, and the water entering the boiler at about 150 degrees temperature is heavier than the water in the boiler. The cooler water will go to the bottom and reduce the temperature in that part of the boiler and causing the flues to contract in length as well as in diameter and this has a tendency to pull them out of the sheet. This will loosen them and cause them to leak. After the fire has been knocked this tendency is much greater, and for that reason cold water should not be put into a boiler after the fire has been knocked out. Always fill the boiler before the fire is knocked out.
- Q. Is warm water in the tank of any advantage in making steam
rapidly?
A. Yes; careful experiments have shown that a locomotive will generate one per cent. more steam for every eleven degrees that the tank water is heated; thus by heating the feed water in the tank from 39 degrees to 94 would effect a saving of five per cent.
- Q. Then why not heat the feed water to the boiling point (212
degrees)?
A. If the feed water is heated much above 100 degrees it will not condense enough steam in the injector to cause it to work properly. Some injectors will work hotter water than others. It would also spoil the paint on the tank if heated to a much higher temperature.
- Q. At 200 pounds pressure per square inch, what is the pressure per
square foot on the sheets of a boiler?
A. About fifteen tons.
- Q. What is the total pressure on the fire-box of a large
locomotive?
A. Over 3,000 tons.
- Q. Give a practical definition of heating surface.
A. The heating surface of a boiler includes all parts of the boiler and tubes that are directly exposed to fire or heat from the fire and are surrounded by water.
- Q. Should an engine be slipped to get water out of the cylinders or
steam passages?
A. No; the water should be worked out by opening the cylinder cocks and starting the engine slowly.
- Q. What does it indicate when the smoke trails back over the train
and into the coaches after shutting off?
A. It indicates poor firing or a lack of understanding between the engineer and fireman in regard to where the engine was to be shut off.
- Q. Before shaking grates or dumping the ash-pan, what should be
observed?
A. That the engine is not passing over bridges or cattle guards, crossings, switches, interlocking fixtures, or in yards. Fire on the track should be extinguished promptly at places where ash-pans are cleaned.
- Q. Which is easier and more satisfactory on a long run, to stop and
clean the fire if necessary or to continue to the end of a long, hard trip with a dirty fire?
A. Stop and clean the fire if necessary. It will save fuel and labor during the remainder of the trip and may also save an engine failure.
- Q. Should you examine the flues to see if they are stopped up and
leaking, and inspect the grate and grate rigging carefully before leaving the engine at a terminal?
A. Yes, so they can be reported if necessary. Clean flues and grates working well make a vast difference in the success of a fireman, and a great many engine failures could be avoided by keeping the flues and grates in proper condition.
- Q. How should cab lamps, signal lamps, oil cans and lanterns be
cared for?
A. They should be kept clean, free from leaks and always filled and ready for service before leaving terminals.
- Q. About how many drops in a pint of valve oil when fed through a
lubricator?
A. About 4,500 drops.
- Q. Assuming that five drops per minute are fed to each of two valves
and one drop per minute to the air pump, how many hours would be required to feed one pint of valve oil?
A. About eight hours.
- Q. Assuming that the engine is running twenty-miles per hour, how
many miles per pint would be run?
A. About 160 miles per pint.
- Q. How many drops per minute should ordinarily be fed?
A. This will vary with the size of the locomotive and the work to be performed. On small yard engines one drop per minute for each cylinder is usually sufficient and one drop for the air pump every two or three minutes. This depends on the condition of the pump and the service being performed. For large engines in slow freight service four to five drops per minute, and for large engines in heavy fast passenger service from five to seven drops per minute should be fed. Air pumps in freight service where the brake pipe is in moderately good condition can usually be run with one or two drops per minute when handling long trains of cars equipped with air brakes.
- Q. Will any bad results ensue from filling the lubricator full of
cold oil?
A. Yes; when the oil gets hot it will expand and may break the glass or bulge or burst the lubricator.
- Q. If a sight feed gets stopped up, how could you clean it out?
A. Close the water valve and the regulating valves to the other feeds.
Open drain cock and draw out a small quantity of water so as to bring the oil in top part of lubricator below the top end of oil pipe leading to feed arm, then open wide the regulating valve to feed that is stopped up and the pressure from the equalizing tube will force the obstruction out of the feed nozzle and up into the body of the lubricator. Next, close this regulating valve until the feed glass fills with water, then open water valve and start feeds.
- Q. How would you clean out chokes?
A. First, shut off boiler pressure and condenser valve; next, remove feed valve bonnet, then open main throttle valve, when the steam from steam chest will blow back through the choke plug, clearing it of any obstruction.
- Q. What is superheated steam?
A. It is the saturated steam separated from the water from which it is generated with more heat added, increasing its temperature from 100 degrees to 250 degrees Fahrenheit above the saturated steam temperature.
- Q. What is the advantage of superheating or increasing the
temperature of the steam?
A. By increasing the temperature of the steam the volume of a given weight of steam is increased and all losses due to cylinder condensation are eliminated, which result in a reduced steam consumption, a saving in coal and water and increased boiler capacity.
- Q. How is the increased temperature obtained by the use of the
superheater?
A. By admitting the saturated steam into a partitioned receiver which has a number of 1-1/2-inch pipes attached to it. These are located in and extend nearly the full length of the large flues, the steam having to pass through these 1-1/2-inch pipes on its way back to the receiver, absorbs the heat from the gases passing through the large tubes, causing its temperature to rise, or in other words, become superheated.
- Q. How much is the volume of steam increased by superheating?
A. For each 100 degrees of superheat added to saturated steam, at temperatures ordinarily used in locomotive practice, the volume of a given weight is increased roughly from sixteen to seventeen per cent.
- Q. Why is the superheated steam so much more economical on coal and
water than the saturated steam?
A. Because for a given amount of water evaporated you can increase the volume of steam 33 per cent. by superheating. It is readily seen that the coal does not have to be burned if the steam used has 33 per cent. more volume for filling space, or in other words, only so much steam can be admitted to the cylinders for every movement of the valve, and what can not be used must remain in the boiler, so if the engine can not use all of the steam that the boiler is capable of generating, the saving must show in coal and water. If you can not use all of the steam you do not have to burn coal to make it.
- Q. Which is the better practice, to close the feed valves or water
valve while waiting on sidings, etc.?
A. Close the feed valves; the water valve may leak.
- Q. How can you tell if equalizer tubes become stopped up or broken?
A. If they were stopped up the equalization would be destroyed, and when the steam-chest pressure was less than the boiler pressure the feed would work too fast, the oil would enter the feed glass in a stream instead of forming into drops. If they were broken, the lubricator could not be used. The auxiliary oilers would have to be used to lubricate the cylinders.
=AIR BRAKE QUESTIONS=
- Q. Explain how an air compressor should be started.
A. A compressor should be started slowly, with the drain cocks open to allow the water of condensation to escape; and as no provision is made in the steam end to cushion the pistons at the end of their stroke, it should be allowed to work slowly until a pressure of thirty or forty pounds has accumulated in the main reservoir; the piston, having to work against this pressure, will be cushioned at the end of each stroke.
After the compressor is warm, the drain cocks should be closed and the throttle opened sufficiently to run the compressor at the proper speed.
The lubricator should then be started and allowed to feed freely until eight or ten drops have passed, when the feed should be reduced to an amount sufficient for proper lubrication.
- Q. What kind of oil should be used to lubricate both the steam and
air cylinders of the compressor?
A. Valve oil.
- Q. Where does the main reservoir pressure begin and end?
A. Begins at the discharge valves in the compressor and ends at the engineer's brake valve.
- Q. Where does the brake pipe pressure begin and end?
A. The brake pipe pressure begins at the feed valve and ends at the brake pipe side of the triple piston, conductor's valve and at the rear angle cock.
- Q. What is meant by excess pressure, and where is this pressure
carried?
A. Excess pressure is carried in the main reservoir and is the pressure above that in the brake pipe.
- Q. Why is excess pressure necessary?
A. To insure the prompt release of all brakes and quick recharge of the brake pipe and auxiliary reservoirs.
- Q. How is the amount of excess pressure regulated?
A. By the compressor governor.
- Q. Name the different parts of the air brake as applied to a car.
A. The triple valve, auxiliary reservoir, brake cylinder, brake pipe, angle cocks, cut-out cock, retaining valve, centrifugal dirt collector and strainer tee.
- Q. What is the duty of the triple valve?
A. The triple valve has three duties to perform: Charge the auxiliary reservoir; apply the brake; and release the brake.
- Q. What is the purpose of the auxiliary reservoir?
A. It is here that the air is stored that is admitted to the brake cylinder when the brake is applied; thus, each car carries its own brake power.
- Q. What is the purpose of the brake cylinder?
A. It is here where the power of the compressed air is converted into work by forcing the brake piston out, moving the brake levers, rods and brake beams, forcing the brake shoes against the wheels, applying the brake.
- Q. What is the purpose of the brake pipe and angle cocks?
A. It is through the brake pipe that all brakes in the train are placed into communication with the brake valve on the locomotive; and through the brake pipe, air from the main reservoir flows to the triple valves and auxiliary reservoirs on the different cars. The angle cocks are for the purpose of opening and closing the ends of the brake pipe.
- Q. What is the purpose of the cut-out cock?
A. To cut out any brake that is not in operating condition.
- Q. How is a brake cut out?
A. By closing the cut-out cock in the cross-over pipe and bleeding the auxiliary reservoir.
- Q. How would you bleed an auxiliary reservoir?
A. By holding open the release valve on the reservoir until all air has escaped.
- Q. How would you bleed off a stuck brake?
A. By holding open the auxiliary release valve until the brake piston starts to move toward release position.
=OIL BURNING LOCOMOTIVES=
- Q. What are the fireman's duties on arrival at the enginehouse
previous to going out on an oil burning locomotive?
A. In addition to the duties usually performed on any engine, the fireman should observe the condition of draft pans and arch, observe the condition of burner and dampers; try the oil regulating valve; see that the burner is properly delivering fuel oil to the fire; see that the oil heaters are in working order; that the fuel oil is heated to proper temperature; and see that proper supplies of fuel oil, sand and water have been provided as well as the necessary tools for handling an oil fire.
- Q. How warm should the oil be at all times in the tank.
A. Warm enough to flow freely at all times, usually about 112 degrees.
This temperature is about that which the hand can bear on the outside of the tank.
- Q. If the oil is too warm, what happens?
A. Many of the good qualities of the oil may be lost by keeping it too warm, and the burner is more difficult to operate and does not work as well when the oil is kept at too high a temperature. Should the oil be too warm, it will give off too much gas which would be liable to cause an explosion in the oil tank.
- Q. What tools are necessary for firing purposes on an oil burning
locomotive?
A. The tools necessary for firing an oil burning engine include sand horn, brick hook, and a small iron bar to be used in cleaning carbon from the mouth of the burner.
- Q. What is liable to happen if the heater valve is open too much?
A. If the heater valve is opened too much it would be liable to burst the heater hose as well as to heat the oil to a too high temperature and place an unnecessary strain on all the heater connections, causing them to leak.
- Q. What should be done on approaching stations where additional
supply of fuel oil is to be taken?
A. Shut off the fire, close safety and main oil valves, remove any lamps that are so close as to be unsafe when manhole cover is open.
- Q. What care must be exercised in the use of lamps, torches or
lanterns about oil tanks whether hot or cold?
A. Never permit oil lamps or oil torches to be carried within ten feet of the tank opening. Only incandescent lamps or pocket flash lights should be used around oil tank manhole when taking oil.
- Q. How can oil in the tank be measured without taking a light to the
manhole?
A. By inserting a measuring stick into oil in tank and taking stick to the light for reading.
- Q. What precautions must be taken before entering tanks that have
been used for oil to clean or make repairs?
A. Oil tanks, before being entered by workmen, should be thoroughly steamed and cooled before being entered. For safety they should be steamed from six to eight hours.
- Q. How should the fire be lighted in an oil burning locomotive?
A. First see that no one is working under the engine, that there is the proper amount of water in the boiler and that it will flow through the gauge cocks, that there is no accumulation of oil in the ash-pan or fire-box or existing leaks throughout. If there is no steam in the boiler, the steam connections can be made to the three-way cock at the smoke-arch that will answer for blower and atomizer. If there are twenty pounds of steam in the boiler, it can be operated with its own blower.
If oil in the tank is too cold to flow into the burner readily, it must be heated. Open the front damper and put on the blower strong enough to create the necessary draft, open the atomizer valve long enough to blow out any water that might be in the steam pipe to the burner, then close the valve and throw a piece of burning waste in front of the burner and open the atomizer valve enough to carry oil to the burning waste and open the regulating valve slowly until the oil is known to be ignited.
Watch the ignition through the hole in the fire-box door, then regulate the steam and oil supply to suit. Be sure that no oil is wasting below the burner or an explosion may result that will prove disastrous.
- Q. Should the fire go out and it is desired to rekindle it while
bricks are hot, is it safe to depend on the hot bricks to ignite the oil without the use of lighted waste?
A. No; depending upon the heat from the firebricks to re-light the fire is dangerous and forbidden.
- Q. What is termed an atomizer, and what does it perform?
A. The atomizer is a casting containing two long ports with an extension lip; the upper port is for oil and the lower one for steam. The lip aids the steam in atomizing and spreading the oil, which, when properly mingled with the air and ignited, will produce combustion. The atomizer is located just under the mud-ring and pointed a little upward, so the stream of oil and spray of steam would strike the opposite wall a few inches above the bottom if it would pass clear across the fire-box.
- Q. In starting or closing the throttle of the locomotive, how should
the fireman regulate the fire, in advance or after the action of the engineer?
A. In starting an oil burning engine the oil should gradually be brought up as the throttle is opened and the movement and amount of oil should be kept slightly in advance of the action of the engineer in order to prevent an inrush of cold air as the engine is working, which would result in injury to the fire-box and flues. When the throttle is to be closed, the fire should be reduced very slightly in advance of the closing of the throttle. This is to prevent the engine from popping off and black smoke drifting back over the train.
- Q. Is it necessary that the engineer and fireman on an oil burning
locomotive work in perfect harmony and advise each other of intended action at every change of conditions?
A. Yes; they should work in harmony with each other on any locomotive.
The fireman should watch every move the engineer makes, and the engineer should advise the fireman of every intended change of the throttle, so he can operate his valves accordingly and save fuel and avoid black smoke.
- Q. What is the effect of forcing the fire on an oil burning
locomotive?
A. Forcing the fire is very hard on fire-box sheets and flues, and will cause them to leak. An even temperature should be maintained in the fire-box of any locomotive.
- Q. Is a careful regulation of steam and oil valves and dampers
necessary to obtain the most economical results?
A. Yes; the fireman's oil valve should be opened just wide enough to permit a sufficient amount of oil to be fed to produce a good fire, but not wide enough to waste oil or produce a volume of black smoke.
- Q. How can you judge whether the combustion is good or bad, so the
valve may be regulated accordingly?
A. By the color of the fire in the fire-box. When it is a dull red color, the temperature is below 1,000 degrees and combustion is incomplete, dense black smoke will issue from the stack. If it is a bright red, the temperature will be about 1,800 degrees and combustion very good, and no black smoke will appear from the stack.
- Q. How should the flues be cleaned from soot when running, and about
how often is this necessary?
A. By placing a small quantity of sand in an elbow shaped funnel or horn, and by inserting same in an opening provided in fire door while engine is working hard, allowing the exhaust to draw the sand through the flues, thus cutting soot and gum from them in its passage and discharging it from the stack. It is necessary that the flues be cleaned of soot on leaving terminals or sidings where the engine has been at rest for any length of time, and also as often as found necessary to aid the engine in steaming. This depends to a great extent upon the degree of perfection with which combustion is obtained.
Attention should also be given flues just prior to entering points where engine is to be put in roundhouse or otherwise detained in order to leave the flues clean, as this will aid in putting engine under steam with little delay where the blower alone is to be relied on for draft.
- Q. Is the injudicious use of the blower particularly injurious on an
oil burning locomotive?
A. Yes; the injudicious use of a blower is injurious to any boiler. The cold air drawn through the fire-box is hard on the sheets and flues and will cause them to leak.
- Q. Is the blower more injurious when a light smoke is emitting from
the stack or when a dense black smoke is emitting?
A. It is most injurious when a light smoke is emitting.
- Q. In drifting down long grades should the fire be shut off or
burned lightly? Why?
A. The fire should be burned lightly and not permitted to get low enough to allow the fire-box to lose its temperature, as this will contract the flues and cause them to leak.
- Q. How should the fire be handled when switching?
A. The fire must be regulated to meet the requirements of the work the engine is performing on each move and to protect against any possibility of the fire being drawn out by the exhaust.
- Q. Would not some fuel be wasted in this way?
A. Not necessarily. A waste of fuel can be avoided by close attention on the part of the fireman when switching as well as when running.
- Q. How should the fire be handled when leaving stations?
A. It should be burning brightly and strong enough to prevent the draft from putting it out when the throttle is opened. And a little smoke should show up at the stack, which would indicate that the fire was being forced just a little ahead of the working of the engine.
- Q. Which is desirable, to use as much or as little steam jet
atomizer as possible?
A. It is desirable to use as little atomizer as will make engine show perfect combustion and economy.
- Q. What is the result of too little steam jet atomizer when standing
at stations or when the engine is working light?
A. The result of too little atomizer when standing at station or when engine is working lightly, will result in the oil not being carried far enough into the fire-box or arch and not properly atomized and the fire is liable to go out. The oil will drop from the mouth of the burner into the draft pan to the ground where it is very liable to start a fire under the engine.
- Q. If too much steam jet atomizer is used with a light fire?
A. It will create a disagreeable gas, which will cause the fire to burn with a succession of light explosions and kicks, also a waste of steam, and which would reduce the fire-box temperature.
- Q. When the fire kicks and smokes, what should be done?
A. The atomizer should be adjusted. If this does not overcome the trouble, the heater should be put in service, for, possibly, the oil is too cold to flow freely. Another cause of the fire kicking and smoking results from water being mixed with the oil. If this is the case, it should be drained out of the oil tank immediately.
- Q. How should the dampers be used on an oil burning locomotive?
A. They should be opened just enough to admit sufficient air to produce perfect combustion, but not enough to cool the fire-box. The dampers should be closed when the engine is drifting or when at rest and the fire is cut very low or is out entirely.
- Q. About how much smoke do you consider an oil burning locomotive
should make under adverse conditions, when the engine is steaming well, but is being crowded by the engineer?
A. Only a light smoke should show at the stack.
- Q. What color is most desirable at peep holes in the fire-box?
A. A white color is most desirable.
- Q. What will produce the bright red color?
A. Leaky steam pipes, side seams, flues and improper combustion will produce a ruddy color in the fire-box.
- Q. How does water in the oil affect the fire?
A. Water in the oil will produce popping or kicking with the fire in the fire-box and at times the fire will die down entirely and then flash up as the water disappears and the oil reaches the burner. The most noticeable result of water in the oil is the fact that the fire will get very low. It will almost go out entirely and then will suddenly flash up again as the oil appears. Water in the oil produces a very dangerous condition and should be prevented immediately by draining the water from the fuel oil tank.
- Q. Do you consider it advisable to keep the burners clean, and how
often?
A. When equipped with steam blow-out pipes, they should be blown out before commencing trip so that burners will distribute oil evenly to each side of fire-box.
- Q. What position should burner be with reference to level and in
line with center of fire-box?
A. It is very essential that burners be level and throw flames just to clear floor of arch in order to derive full benefit of heating surface, as the draft has a great tendency to elevate flames, at opposite end of the fire-box.
- Q. Are you aware that in course of time the atomizer port will
become worn too large and will discharge too large a volume of steam to properly atomize, and the remedy?
A. Yes; the lip or bushing should be closed to proper opening so that steam will be restricted at the nozzle and escape with a bursting effect to properly atomize the oil instead of flowing out in quantities against flash walls before it has time to ignite.
- Q. What is the real object of having the fire-box lined with bricks,
and will engine steam without them?
A. Not so well as with the brick, the sheets being in contact with water are too cool to flash the oil readily and hence the use of what is called a "flash wall" built of fire brick and heated to a very high temperature aids combustion very materially.
- Q. Do you consider it your duty to keep close inspection of brick
work as to need of repairs, such as air entering between brick and side sheets?
A. Yes. To see that plaster is kept between the walls and sheets to keep cold air from being drawn in.
- Q. Will engine steam if brick falls in front of burners or in path
of flame and what may be done?
A. No. Remove them with the brick hook or rod by pulling them out through damper of draft pan.
- Q. Where engine is equipped with an oil-reheater or oil line, do you
consider it a help to engine's steaming qualities when used?
A. Yes; at all times this heater should be used.
- Q. Why use second heater? Why not heat it to a high temperature in
oil tank with oil heater?
A. Too much gas generating and boiling the oil continually destroys the higher qualities besides being hard to control the flow through regulation valve.
- Q. Do you consider a vent hole in oil tank advisable, and why?
A. Yes; to allow any accumulation of gas to escape and to admit the air so that oil will flow freely.
- Q. Do you inspect your oil pipes and report all leaks? What other
bad effect has a pipe leak aside from waste of oil?
A. Yes. It will cause oil to feed irregularly.
- Q. Are you aware that keeping the flues clean is the greatest one
thing that you can do in regard to fuel economy, and how often should they be cleaned?
A. Yes. At least every ten miles.
- Q. Do you know that the engine should be working hard and at a speed
not less than twenty miles per hour when sanding flues to avoid the sand falling to floor of the fire-box and accumulating in front of them?
A. Yes.
- Q. Do you realize that on first closing throttle you should not
adjust fire too low? Explain best method.
A. Yes. I would allow steam pressure to fall back some fifteen pounds before throttle is closed and on having closed same leave a good fire in box, allowing it to cool gradually to avoid leaky flues, broken staybolts, cracked sheets caused by sudden fall of temperature.
- Q. How is the flow of oil controlled?
A. By the valves in tank and pipe connections.
- Q. Name these valves, their location and purpose.
A. The safety valve controls the flow of oil from the fuel oil tank through an opening in bottom sheet of tank to the pipes leading to burner. This valve is forced to its seat by a heavy spring and is held off its seat by a key in the upright rod extending above the top of tank. To this key a rope or chain is attached and also attached to the cab to cause the pin in rod to be pulled in case of a separation between engine and tank and allow the valve to be seated by its spring and avoid a waste of oil.
The second or main oil valve is located in oil pipe under deck leading to burner. It is usually of the plug-cock pattern connected by bell crank and this connected to some part of the engine by chain, in which case it also acts as a safety valve in case of separation between engine and tender. In other cases it is connected by an operating rod extending above deck of tender where it can be operated by hand in case of safety valves failure to shut off the flow of oil.
The third or firing valve is usually located between heater box and burner, and is provided with an upright rod extending into cab where it is provided with a handle or lever in position to be conveniently handled by fireman while seated in cab. This valve regulates the flow of oil desired to reach the fire.
- Q. When shutting out fire which valve should be closed first? Why?
A. The safety valve. To allow the oil in pipes to be consumed and to see that this valve is in working order.
- Q. Should safety valve fail to shut off the flow of oil in such
cases would it be safe to rely on the firing valve to shut off the fire?
A. No. The main valve should then be closed.
- Q. Should the firing valve be depended upon to shut off the fire at
any time? Why?
A. No. From constant use they are frequently leaking and the trouble is not detected while in use, and again there is always danger of the handle being moved by workmen or others about the cab.
- Q. What is a heater box?
A. It is an apparatus having two passages, one for steam passing from boiler to heater pipes in tank and another passage for oil from tank before it is delivered to burner. In this manner the oil before reaching the burner is heated much higher than the temperature of that contained in tank.
- Q. In the event of the heater pipes or connections becoming
defective, how could the oil be heated in tank?
A. By closing the firing valve, closing the valve on heater pipe, and opening valve on heater box, the steam from heater throttle can be passed directly through the oil feed pipe to the fuel supply.
- Q. In the event of an objectionable quantity of water in oil, how
can it be removed?
A. In some instances the tanks are provided with drain pipes for this purpose, but in the absence of same, the feed hose or pipe between engine and tank can be disconnected and used as a drain to fuel oil tank.
- Q. What effect has leaks between fuel tank and firing valve?
A. A waste of oil only.
- Q. What effect has leaks between firing valve and burner?
A. In addition to a loss of oil while fire is burning low, and but little steam atomizer being used, it interferes very materially with the engine's steaming by admitting air when using considerable steam atomizer. This causes a very irregular oil feed.
- Q. What action of the fire would indicate leaks in pipes between
firing valve and burner?
A. The fire-box will give off sounds similar to slight explosions, and the smoke at stack will indicate irregular fuel feeding.
- Q. What would you consider the proper adjustment of burner?
A. That which will provide for the delivery of the oil from burner to flash wall without striking arch, side walls, or floor brick while doing so.
- Q. In case it becomes necessary to fire up an oil burning engine
with wood, what parts should be given particular attention?
A. The brick work. To see that same is not damaged or displaced while placing the wood in fire-box, also to protect by placing brick over that portion of burner extending into fire-box ahead of mud ring, or by so arranging the wood in fire-box as to prevent any great amount of heat from reaching the burner and melting nozzle of same.
- Q. In case of sudden drop in steam pressure, what might be the
cause?
A. Loose brick perhaps fallen in front of burner and obstructed the flow of oil. The petticoat pipe may be loose and out of line or the dampers may have fallen shut.
- Q. In case brick have fallen in front of burner, how can they be
removed?
A. By a hook provided for that purpose. They can usually be forced out through the vent openings, but if this cannot be done, they should be thrown against the blast wall in order to get them as far as possible out of the course of the fuel feed.
- Q. In case a petticoat pipe becomes deranged, what can be done?
A. In case it cannot be put back in proper position, it should be removed altogether. (Trips have been successfully completed in this manner.)
- Q. Will a corroded burner mouth prevent the proper delivery of fuel
to fire?
A. Yes.
- Q. What causes the mouth of burner to corrode?
A. The asphaltum and sand contained in the oil.
- Q. How can this be removed on the road?
A. By having a hook or rod provided with a point that can be inserted into mouth of burner.
- Q. Why should a fuel oil tank not be filled to its holding capacity?
A. Because when heater is applied the oil would expand and overflow.
- Q. In case of derailment or other accident that might cause the
fireman to desert his position in cab, what should he do?
A. Pull key out of safety valve rod, thereby allowing oil feed from tank to be shut off.
=MECHANICAL EXAMINATION=
THIRD SERIES
- Q. What are the duties of an engineman before attaching a locomotive
to the train?
A. He should make a complete inspection of the locomotive, observing all important nuts and bolts, look for any signs of hot bearings on previous trip, see that the engine is equipped with necessary tools and supplies, test both of the injectors and the air brake equipment to be sure they are in good working order, see that headlight and signal lamps are in place and ready for service, observe water conditions in boiler, inspect the interior of the fire-box and see that the locomotive is properly lubricated.
- Q. What tools should there be on the locomotive?
A. Such as are necessary to properly operate the locomotive, care for the machinery, disconnect and block up in case of breakdown and the necessary firing tools.
- Q. What examination should be made after any repair work has been
done on valve, brasses, etc.?
A. See that brasses are properly fitted, keys fastened and nuts made tight. If any repairs have been made on valves or valve gear, would see that the reverse lever could be moved freely and that all movable parts had been properly replaced; would also give especial attention with reference to lubrication of these parts.
- Q. What attention should be given to boiler attachments, such as
gauge cocks, water glasses, etc.?
A. Would see that the gauge cocks can be opened to try the water and closed, so steam and water would not come out into cab. Observe the water glass and note if water is moving up and down in the glass, see that the steam valve at the top and water valve at bottom of glass could be opened and closed, and allow water and steam to circulate freely through the glass.
- Q. What do you consider necessary to report on locomotive boilers?
A. Should report all defects on boiler and its attachments while engine is in engineer's charge.
- Q. Trace the steam from the boiler through the cylinders to the
atmosphere and explain how it transmits power.
A. Steam enters the throttle valve located in the highest part of the dome in order to get the driest steam, then passes through the standpipe and dry pipe out of the boiler to the steam pipe tee or nigger-head located in the front end, then through steam pipes to the steam chest.
A steam valve in each steam chest distributes the steam so that it enters the cylinders at or just before the beginning of the stroke; pushing the piston to the end of its stroke; just before the piston reaches the end of the cylinder, the steam valve opens communication to the exhaust port through a cavity in its exhaust side, then through the exhaust pipes and tips up through the draft or petticoat pipe and stack to the atmosphere.
When steam pushes the piston through the cylinder, its power is transmitted by the main rod to the main crank pin which causes the wheels to revolve, thus moving the engine and its train.
- Q. Why is it important that there be no holes through the smoke-box
door or front end and none in smoke-box seams or joints?
A. So as to maintain as good a vacuum as possible in the smoke-box and prevent small amounts of air coming in through leaks which tend to heat and warp the smoke-box and its door.
- Q. How should the locomotive be started to avoid jerks, and what
train and other signals should be looked out for at the time of starting?
A. Place the reverse lever in full gear, open the throttle valve gradually so as to start the train one car at a time and easily. Look for signals ahead to show that the track is clear and switch is in correct position, then look for signals from the rear end that the train is all coming.
- Q. Will an engine equipped with superheat units move as quickly as a
saturated steam locomotive when throttle valve is first opened?
A. No.
- Q. Why?
A. Because steam must first pass through superheat units before it enters the steam pipes leading to steam chest.
- Q. In placing engine on the turntable, at water or stand pipes, or
at other similar places, what must be done?
A. Close throttle valve sooner so that the steam confined in superheat units, pipes and steam chests, will have passed out to the atmosphere.
- Q. After a locomotive has been started, how can it be run most
economically?
A. By regulating the supply of steam to the steam chest with the throttle and the point of cut-off with the reverse lever; so that no more steam be used than necessary to maintain the proper speed, whenever possible working the engine at short cut-off so as to use steam expansively.
- Q. What is meant by working steam expansively?
A. Hooking the reverse lever up toward the center gives the valve a shorter travel and closes the live steam port when the piston has made only a part of its stroke. This cuts off the supply of live steam coming from the steam chest. The expansion of the steam already in the cylinder pushes the piston to the end of its stroke without the use of a full cylinder of live steam.
- Q. How rapidly should water be supplied to the boiler?
A. No faster than it is evaporated into steam, unless just before a hard pull; or when shutting off with a heavy bright fire in the fire-box to prevent waste of steam at the pops.
- Q. What is the difference between priming and foaming of a
locomotive boiler?
A. Priming is caused by carrying the water too high in the boiler so that when the throttle valve is opened some of it passes over with the steam in the form of a spray. Foaming is caused by the water becoming dirty from animal or alkaline matter, so that heat makes it foam like soap suds. Muddy water or certain vegetable matters will also make a boiler foam.
- Q. What should you do in a case of foaming? What in a case of
priming?
A. In a case of foaming, if possible, allow the boiler to cool off a little, increase the supply of feed water to prevent water getting too low, and whenever possible blow some of the dirty water out of the boiler, replacing it with clean water. In case of priming, shut off the supply of feed water until the water level drops to the proper height in the boiler.
- Q. What danger is there when the water foams badly? When it primes
badly?
A. There is danger of knocking out cylinder heads, cutting the valves, stalling on some grade or getting on some train's time because the engine cannot be worked to its proper power. When shutting off steam, the water is liable to drop below the crown sheet and thus risk burning the fire-box. When water primes badly, it is liable to break cylinder packing rings, knock out cylinder heads, break bolts in the steam chest and cut the valves. In such a case additional oil should be fed to the steam chest until the valves are properly lubricated.
- Q. Suppose that with the water glass in good working order,
immediately after closing the throttle the water disappeared from the water glass, what should be done?
A. Would open the throttle and endeavor to raise water until both injectors would put enough water into the boiler to make it entirely safe to close the throttle. If unable to raise the water level to the lower gauge cock would smother the fire or put it out entirely, if necessary, keeping both injectors working.
- Q. What work about a locomotive should be done by the engineman?
A. Inspection of the engine both before and after the trip. The engineer should do any necessary work on the engine after starting out on the trip to avoid breakdowns and insure getting over the road promptly. This means tightening up any important bolts that work loose on the trip and keeping parts from working out of position, adjusting wedges and rod keys.
- Q. How should the work of setting up the wedges be done?
A. Place the engine on the upper quarter on the side with the loose wedge. Do not set the brake if brake shoe will push the driving box against the defective wedge, but block engine truck wheels so the engine cannot move, push the boxes against the shoe or dead wedge with a little steam, set the wedge up until it is a snug fit, then pull it down about one-sixteenth of an inch and fasten. Provision should be made for expansion of the box when it gets warm.
- Q. How should rod brasses be keyed?
A. If properly fitted they should be keyed brass to brass; if not so fitted, they should be keyed on the large part of the pin so they will be free enough to run without heating and snug enough to run without pounding. Do not key them so tight at either end as to prevent the lateral motion of the brass on the pins.
- Q. How should an engine be placed for the purpose of keying the rod
brasses?
A. For the main rod, place the engine on the quarter or the top forward eighth, whichever place gives the largest diameter of the pin to key the brass against. After keying up, test by moving the wheel to another position and see if brasses are free on the pin. For the side or parallel rods, always place the engine on the center for the side that is to be keyed.
- Q. How should the side rods on a mogul or consolidation locomotive
be keyed?
A. Place the engine on the center on that side, key up the brass on the main pin first, work each way toward the ends of the rods, being careful to keep them the proper length so they do not bind when passing either center. Be sure that wedges are properly set up before keying the side rods.
- Q. What is the necessity for keeping the brasses keyed up properly?
A. If too tight, they will surely run hot; if too loose, they will pound and injure the brasses as well as endanger the safety of the straps and rod bolts. Very loose brasses can pound enough to get hot.
- Q. What is meant by an engine out of tram? Out of quarter?
A. When corresponding wheels on opposite sides of the engine on different axes are not spaced equally apart; where the axle of any wheel is not at a right angle to the center line from front to rear of engine, so they do not run square on the rails, or where the space between the axle centers on opposite sides is not equal. This is sometimes indicated by unequal flange wear and should be reported at once. Wheels are out of quarter when the crank pin in one wheel is not exactly 90 degrees or one quarter of a turn from the pin in the wheels on the other end of the same axle.
This is usually caused by slipping the engine with sand on one rail only and the condition of engine should be reported at once.
- Q. Describe a piston valve.
A. A piston valve is a cylindrical spool-shaped valve constructed with packing rings much the same as the steam piston that moves through the cylinder, except that a piston valve is double or composed of two pistons connected by center rod or spool working in a bushing of equal diameter. Steam and exhaust ports are cut through this bushing; steam ports to the cylinder and exhaust port to the exhaust pipe. There is also a steam port for live steam from the boiler. As the pressure on this valve is equal in both directions it is practically balanced.
- Q. What is a balanced slide valve? How is it balanced, and why? For
what purpose is the hole drilled through the top of the valve?
A. One in which the steam pressure on the top and bottom of the valve is nearly equalized. This is done by protecting a portion of the top of the valve from the steam pressure. It is usually balanced by strips held against the pressure or balance plate by one or more springs. This is done to prevent live steam from getting on top of valve and thus relieve the valve from the top pressure which would cause excessive friction between the bottom of the valve and its seat.
The hole through the top is to allow any steam which might leak by the strips to pass into the exhaust, so pressure could not accumulate on the top of the valve, also to equalize the exhaust pressure between the top of the valve and exhaust cavity as well as to assist in lubricating the balance plate.
- Q. What is meant by inside and outside admission valves?
A. With an inside admission valve (usually a piston valve), the live steam comes between the piston valve heads, the outside end of the heads being connected with and exposed to exhaust pressure, it admits steam past the inside edges of the valves. An outside admission valve has the space between the ends connected to the exhaust and a space at the ends connected with the live steam. It admits steam past its outside edges. A piston valve can be either inside or outside admission, while a slide valve is always outside admission.
- Q. What is the relative motion of the main piston and the steam
valves for inside admission, and, on the other hand, for outside admission?
A. If the piston is in the front end of the cylinder, an inside admission valve must move forward in order to connect the inside of the valve with the front live steam port to admit steam against the piston.
The outside end of the valve opens the exhaust port for the back end of the cylinder. In the same position of the piston an outside admission valve must move backwards to open the steam port or in the same direction as the steam piston when commencing its stroke.
- Q. What is an Allen ported valve, and what is its object?
A. An Allen ported valve is an outside admission slide valve having an extra port from one end of the valve to the other, above the exhaust cavity and through the body of the valve. This extra port is calculated to admit steam through the valve at the same time that steam passes by the end of the valve into the same steam port, thus doubling the area of opening for live steam when the port is first opened.
- Q. What is the difference in the valve motion for outside admission
valves and for inside admission valves?
A. An outside admission valve must be moved in the opposite direction to an inside admission valve in relation to the movement of the steam piston when beginning its stroke; therefore either the position of the eccentric or the position of the rocker arms in relation to the rocker shaft must be opposite for a change in these valves.
- Q. What is a direct motion valve gear? What is an indirect motion
valve gear?
A. A direct motion valve gear is one in which the valve moves in the same direction as the eccentric rod, that is doing the work, in many cases no rocker arm is used. In case a rocker arm is used, both arms point in the same direction like the letter U. An indirect motion valve gear is one in which the valve moves in an opposite direction to the eccentric rod doing the work. A rocker is used in which the arms point in opposite directions from the shaft connecting them.
Owing to the design and construction of the Walschaert valve gear, it is a direct motion gear when the engine is running in one direction with the link block in the bottom of the link, an indirect motion when the engine is running in an opposite direction with the link block in the top of the link; usually direct motion when running forward.
- Q. How can you detect the difference between a blow in valve or
piston packing?
A. A blow from the valve is more constant and has a somewhat different sound, while a blow from cylinder or piston packing will blow stronger at the beginning of the stroke and gradually decrease as the stroke is completed.
- Q. How would you place engine to locate broken admission steam ring
in piston valve?
A. Would place engine on quarter, reverse lever in center so as to cover ports, then open throttle; and the steam will blow out of cylinder cock at the end of cylinder where broken valve ring is located.
- Q. How would you locate broken exhaust ring in piston valve?
A. Watch the cross-head when engine is working steam. As there will be three normal and one light exhausts, you can determine on which side of the engine the light exhaust takes place.
- Q. What is meant by lead? What by line and line?
A. Lead is the amount of port opening for live steam to cylinder ahead or back of piston when the piston is on the dead center. If the steam edge of the valve is in line with the edge of the steam port when the piston is on the center, it is said to be line and line.
- Q. What is meant by steam lap?
A. The distance that the valve overlaps the live steam edges of the steam ports when it is in the center of its travel over the seat. This distance is measured at one end only, although the valve laps equally at both ends.
- Q. What is meant by exhaust lap? What by exhaust clearance?
A. Exhaust lap is the distance that the exhaust edge of the valve overlaps the exhaust edge of the steam port when the valve is in central position. Exhaust clearance is the opening between the exhaust edge of the valve and the exhaust edge of the steam port with valve in central position. If the valve has neither exhaust lap or clearance it is said to be line and line.
- Q. What is meant by release? What by compression?
A. Release is the point in the travel of the piston when the port is opened. Compression is the distance the piston travels after exhaust port closes before the live steam port opens. During this travel of the piston the exhaust port is closed so the moving piston compresses the steam left in the cylinder.
- Q. With an indirect valve motion and outside admission valve, what
would be the position of the eccentric relative to the crank pin on that side? What with a direct valve gear? What difference between outside admission valve and inside admission valve as to this position?
A. With an indirect valve motion and an outside admission valve, the go-ahead eccentric follows the crank pin with engine running ahead.
Without any lap or lead it would be a quarter of a turn or 90 degrees behind the pin, but as all valves have lap and lead, the eccentric is advanced or placed toward the pin enough to move the valve the amount of the lap and lead. With a direct valve gear and an outside admission valve, the eccentric will be a quarter of a turn or 90 degrees ahead of the crank pin and advanced enough to move the valve the amount of the lap and lead. With an inside admission valve and an indirect valve motion, the eccentric will come the same as for an outside admission valve and direct motion, or more than a quarter of a turn ahead of the pin.
With an inside admission valve and direct motion, as piston valves are usually put up, the eccentric will follow the pin less than a quarter of a turn.
- Q. What effect would be produced upon the lap and lead by changing
the length of the eccentric rod?
A. Lap depends on the construction of the valve. A change of the eccentric rod would not effect it, but would widen the port opening at one end of the travel and reduce it at the other. It should be equal at both ends. Lead is controlled by the position of the eccentric on the axle and it must be equal at both ends. Changing the length of the eccentric rod from the proper one does not really affect the lead, because no proper measurement can be made until lead is equal at both ends. Therefore improper length of eccentric rods varies the port opening at the beginning of the stroke of the piston at both ends.
- Q. Why are eccentric rods made adjustable?
A. In order to change their length to make adjustment of the valve gear not as easily made in other ways.
- Q. Why is it necessary to keep the cylinders free from water?
A. In order to avoid damaging valves and cylinders, to insure perfect lubrication and obtain the most efficient service from the locomotive.
- Q. Where is the piston rod packing located? Where cylinder packing?
A. Piston rod packing is usually soft metallic rings located inside of a gland at the back end of cylinder and around the rod. Cylinder packing rings are usually cast iron, placed around the piston head and bearing against the walls of the cylinder.
- Q. How are metallic packing rings on piston rods and valve stems
held in place? What provisions are made for the uneven movements of the rod?
A. The packing rings fit into a vibrating cup or cone located inside the gland, being held therein by means of a spring as well as by the steam pressure. Provision is made for uneven movement of the rod by making the inside of the gland larger than the vibrating cup and using a ball-joint ring between the vibrating cup and gland.
- Q. While running under steam and there is a failure of part of the
locomotive which does not seem to prevent running at full speed, how would you proceed?
A. Keep the locomotive running if in your judgment it is safe. Try to ascertain what the injury is and be prepared at the next stop to do such work as the case demands, being careful to make the stop at such a place that the work can be done without interfering with the movements of main line trains.
- Q. If one side of a locomotive is disabled, what would you do in a
general way to make it possible to use steam on the other side?
A. Disconnect enough parts to allow for the turning of the wheels and for reversing of the opposite side without moving the valve on the disabled side.
- Q. In case a locomotive in your care became disabled on the road,
what would you do?
A. First see that the train is protected. Next examine the locomotive and see what is necessary to do to move it and if possible the train. If unable to make repairs at once to bring the engine and train forward, would advise exact condition of engine and ask for help. In the meantime endeavor to move the train so as to give other trains the use of the main line.
- Q. Suppose a wash-out plug blew out or a blow-off cock broke off or
would not close, what should be done?
A. Kill the fire, get the train on a side track, if possible, and if unable to make repairs get the engine in condition to be towed in. In all cases with a disabled engine allow the train to drift to a siding, when possible, and stop between the switches so as to allow other trains to pass through siding.
- Q. Can a locomotive boiler without steam pressure be filled by being
towed by another engine? If towed, how filled?
A. Yes. Close all openings where air could enter the boiler. All relief valves, cylinder cocks, gauge cocks, the whistle valve and air pump steam valve should be closed. Place the reverse lever in full gear in the direction the engine is to be towed with water supply valve and injector throttle open. Use engine oil through auxiliary oil cups to oil valves and pistons. The movement of the pistons in the cylinders will pump the air out of the boiler and atmospheric pressure on water in the tank will force water into boiler when the engine is towed.
- Q. What should be done if grates should be burned out or broken
while on the road?
A. Pull the fire off the broken or burned grates, cover that section with any pieces of iron at hand (fish-plates or angle-bars are very good), then level up the fire, clean ash-pan and proceed with full train.
- Q. What precaution should be taken to prevent locomotive throwing
fire?
A. The netting and smoke-arch should be kept in good condition; cinder slide and hand hole plates securely fastened, ash-pan clean and slide dampers for dumping ashes closed. Care should be exercised in working the engine, especially in the vicinity of stations or places where fire is liable to catch. Avoid working the engine hard so as to prevent throwing cinders.
- Q. What shall be done with a badly leaking or bursted flue?
A. Plug it if possible with an iron or wooden plug. If in the fire-box end, a piece of scantling or post can be sharpened and driven into the flue from the fire-box door; it will then burn off up to where the water from the bursted flue keeps it wet. If a bottom flue, would cover it with ashes or green coal so that the leakage would not put out the balance of the fire. If able to maintain steam pressure, would then proceed with a full train.
- Q. What should be done in case the throttle valve stem became
disconnected while the valve is closed? If it became disconnected leaving valve open?
A. Would notify the train crew and Dispatcher and arrange to be towed in. With lubricator working, unless in very cold weather so there is danger of the water freezing in the cylinders or steam chest passages, would not disconnect. By taking out lubricator chokes and steam chest valves from the oil pipe, a larger supply of steam could be got into the cylinders. If in to clear of other trains and practicable, would take up the dome cap and connect the throttle again. If disconnected and valve stuck open, would notify the train crew and Dispatcher, reduce steam pressure until the engine could be handled with reverse lever and brake, and proceed with such a train as the engine can handle.
- Q. In case a valve yoke or stem became broken inside of steam chest,
how can the breakage be located?
A. In this case the disabled valve is always pushed to the front end of the steam chest so that with a slide valve or outside admission piston valve the back port is open to live steam. When given steam, the engine will stop on the eighth, and when reversed will move over to the other eighth, being stopped there by the live steam in the back end of the cylinder having the disabled valve. Steam will blow from the back cylinder cock on the disabled side and cannot be changed by reversing the engine. If the valve is pushed far enough ahead to open the exhaust port, steam will blow through the exhaust so the engine cannot be moved.
With an inside admission valve the forward steam port will be opened and steam will come out of the forward cylinder cock on the disabled side.
- Q. After locating a breakage of this kind, how would you proceed to
put the engine in safe running order?
A. Would move the valve to central position so as to cover both steam ports, if possible. This may be done by taking out the relief valve if on front side of the steam chest and pushing valve back, or taking up the cover for a slide valve; or taking off front head for a piston valve. Disconnect the valve rod from rocker arm and block valve stem so it cannot blow out of the gland or let valve work back. Loosen cylinder head in order to provide for lubricating cylinder so as to leave the main rod up on the disabled side and proceed on one side.
If unable to cover the open steam port it would be necessary to disconnect the main rod on the disabled side, blocking the piston at the proper end of the guides so live steam coming into the cylinder would not move it.
- Q. If a slide valve is broken, what can be done to run the engine on
one side?
A. Remove the steam chest cover, place a thin board between the valve and the steam passages in the seat, replace steam chest cover, disconnect valve rod, and if able to lubricate the cylinders leave up the main rod and proceed on one side.
- Q. If one of the bolts connecting the two parts of a built-up link
on Stephenson gear breaks or is lost, how would you proceed?
A. If temporary bolt cannot be supplied, take down the forward part of the link, disconnect and remove link block, fasten valve to cover ports, and proceed. If moving link will clear rocker arm or other parts of the machinery after link block is taken out, it will not be necessary to disconnect eccentrics.
- Q. What should be done in case of link saddle pin breaking?
A. Remove the broken parts and block the disabled link in such a position that the entire train could be started, using a very short block above the link block in the link slot and a longer one below it.
- Q. With one link blocked up, what should be guarded against?
A. Reversing the engine or moving the tumbling shaft arm down so the link on the disabled side can strike it.
- Q. How can it be known if an eccentric has slipped on the axle?
A. By the uneven exhaust of the engine and a thorough inspection to determine the cause.
- Q. Having determined which eccentric has slipped, how should it be
reset?
A. Place the engine on the center on disabled side and if a back-up eccentric has slipped, would place the reverse lever in full forward gear and mark the valve stem flush with the gland; then place the reverse lever in full back gear and move the slipped eccentric until the mark on the stem returns to its original position, taking notice that the throw of the eccentric is on the other side of the axle from the go-ahead eccentric used as a marker, and tighten up set-screws. To set a go-ahead eccentric, use the back-up one on that side for the marker.
If the eccentric had been keyed on, would move the cam until the key-way in the axle came in line with the slot in the cam. Knowing the position of the eccentric in relation to the crank pin, an inspection would show where it belongs. The eccentrics are usually opposite the third spoke in the driving wheel from the pin, sometimes ahead of the pin, in other cases back of the pin, depending on whether it is an inside or outside admission valve, a go-ahead or back-up eccentric.
- Q. What should be done in case of a broken eccentric strap or rod?
A. For a go-ahead strap or rod take down all broken parts, disconnect valve rod, cover ports, and come in on one side. It is safer to take down also the back-up strap and rod on that side. If the back-up strap and rod is broken, it is possible to secure the bottom end of the link so it will not turn over, work the engine full stroke ahead, proceeding with full train until the main line is clear.
- Q. How should the engine be disconnected if the lower rocker arm
became broken? If link block pin?
A. Would remove broken parts; if moving link would strike anything connected with the rocker box or broken arm it would be necessary to take down both eccentric straps and rods. Block valve central over ports and come ahead on one side. If a link block pin was broken, it might be possible to put a bolt in there to do the work, otherwise block the valve on the center of its seat and if the link will not clear the lower end of the rocker arm take down the eccentric straps and rod. In any case where necessary to take off the eccentric rod always take off the strap also.
- Q. For what breakdown is it necessary to take down the main rod? The
side rod?
A. A broken main crank pin, broken main rod or strap, broken piston rod when near the middle of the rod, broken cross-head or guide, broken valve or seat when steam cannot be kept out of the cylinder. Side rods must come down for broken side rod, broken main pin, or broken side rod pin affecting that rod.
- Q. If it is not necessary to take down the main rod of disabled side
of the engine, how would you arrange to lubricate the cylinders?
A. If cylinder and piston are in good shape and it is possible to block the valve to admit a small quantity of steam into the back end of the cylinder, oil from the lubricator will go through this opening and oil the piston rod and cylinder packing. If not possible to block the valve properly, cover the ports and oil the cylinder through the indicator plug openings or relief plug holes. If not possible to do this, slack off the bolts on the front cylinder head, wedge the head open so oil can be introduced. In some cases it may be necessary to take the head off; that however, allows dust and grit to enter the cylinder.
- Q. What is the by-pass valve, and what is its duty?
A. By-pass valves are connected to the steam port leading to the cylinder. Its duty is to open when the engine is drifting with steam shut off, and close when working steam, to allow air to pass back and forth from opposite sides of the moving piston.
- Q. What is a vacuum relief valve? What a cylinder relief valve?
A. A vacuum relief valve is usually located on the steam chest or the live steam passage to the chest and opens when steam is shut off and engine drifting, allowing atmospheric pressure to pass into the steam chest, closing when working steam. A cylinder relief valve is a pop valve screwed into the cylinder head and set at high enough pressure so it does not open in ordinary service, but will open to allow water to pass out when the exhaust port is closed by valves; or on compound engines when the pressure in the low-pressure cylinder gets too high.
- Q. What would be considered a bad engine or tender truck wheel?
A. One loose on axle; having bad flat spots; very sharp flanges; bad sand spots; cracks shelled out; or other defect that would make the wheel unsafe.
- Q. What should be done if a tender truck wheel or axle should break?
A. Would place a piece of timber or rail across the tender, jack up the corner of the truck that is disabled chain it to the timber and fasten the timber at the other end to hold it so it would carry the disabled truck. If it is possible to slide the wheel or truck, place a tie across the rail and keep the wheel from turning, then slide it to a siding.
- Q. What should be done if an engine truck wheel or axle should
break?
A. Would block between the engine frame and truck frame over the good wheel on disabled side, swing the disabled corner of the truck to the engine frame with a chain. Look out when crossing frogs that disabled truck does not leave the track. With a broken flange, would block the wheel to prevent its turning and skid it to a siding.
- Q. What should be done for a broken tender truck spring?
A. Jack the tender up to where it belongs and put a block in place of the broken spring.
- Q. What should be done with a broken engine truck spring or
equalizer?
A. For a broken spring, raise the front end of the engine and place blocks across the equalizers under the truck spring near the spring band. For a broken equalizer, block on top of engine truck boxes and under truck frame.
- Q. What should be done if a driving spring hanger or equalizer
should break?
A. Would block between the driving box affected and under the frame over it, using hardwood block or piece of iron. Would also block the equalizer up to its proper position between the disabled end and the frame, or over the other end, as the type of spring rigging requires, to hold the equalizer level. For a broken equalizer, would block on top of all boxes affected, would raise the engine by running the proper driving wheels upon an incline or wedge to lift the engine while other boxes were blocked; a re-railing frog comes handy for this work.
- Q. How can an engine be moved if the reverse lever or reach rod were
caught at short cut-off by a broken spring or hanger?
A. By removing the pin at the forward end of reach rod, to free the tumbling shaft and allow it to be moved either forward or back to move the engine. A block should be placed over the link block to avoid damaging it when uncoupled, as well as to hold link in proper position to move the engine. This would allow the engine to be moved and clear the main line.
- Q. How can the blowing of steam past cylinder packing, a valve or
valve strip be distinguished or located?
A. Test for a leaky slide valve, place the engine on the quarter on the suspected side with the reverse lever in center notch; the valve should be in the middle of its travel and cover both ports. If steam blows through the open cylinder cocks on that side, the valve or seat are defective.
A leaky balanced valve strip will allow steam to blow through the hole on top of the valve into the exhaust port in the seat and very little steam will come out of the cylinder cock; in some cases with the valve barely opening a steam port to the exhaust, air will draw in at the cylinder cock. If there is a drip cock in the exhaust pipe under the saddle, the steam will blow out there.
After testing for leaky valve, place the engine on about the forward bottom or top back eighth, block the wheels or set the brakes solid, put reverse lever in corner, open cylinder cocks and give the engine steam. If steam comes out of both cylinder cocks, and testing valve shows it is tight, then the packing is blowing. Cylinder packing should be tested with steam first on one side of the piston and then on the other.
- Q. If engine should blow badly and be unable to start the train when
on the right dead center, on which side would be the blow generally?
A. On the left side. If the side standing on the quarter cannot start the train, the trouble is usually there.
- Q. If throttle were closed and steam came out of cylinder cocks,
what might be the cause?
A. To test for this, first shut off steam connection to the lubricator; steam leaking into the cylinders can come from a leaky throttle or leaky dry pipe.
- Q. Is it possible to distinguish between a leaky throttle and a
leaky dry pipe?
A. Yes; a leaky throttle usually leaks steam at all times. A leaky dry pipe will leak both steam and water. It will show a stream of water at the cylinder cocks when the water level in the boiler is raised above the leak in the dry pipe.
- Q. What effect have leaky steam pipes in the smoke-arch, and how
should they be tested?
A. Leaky steam pipes waste steam and very seriously affect the draft in the front end. A bad leak in the back part of the joint at the bottom will blow into the tubes and make the engine smoke at the door with throttle wide open while standing still. To test them, open the front door and cover the joint with fine cinders. When the engine is given steam, the cinders will blow away from the leak; to properly test them in the shop, water under heavy pressure should be used.
- Q. How should the test for a leaky exhaust pipe joint, or a leaky
nozzle joint be made?
A. About the only test that can be made on the road is to open the front end and reverse the engine with throttle partly opened, watching the suspected joint at the same time. For the bottom one with cinders around the joint, for the top one it can sometimes be detected by holding a torch near the joint.
- Q. What should be done if a steam chest cracks?
A. Would loosen up the steam chest cover to free the sides, and wedge between the studs and walls of chest, crowding the broken parts together. A brake shoe key does this nicely. Would then tighten down on steam chest cover and proceed.
- Q. What should be done if a steam chest breaks?
A. Would take off steam chest cover, place strips of boards over the steam inlets and block on top of them so that the steam chest cover would hold them in place and prevent live steam coming out of inlet.
Would then make the necessary disconnection and proceed on one side.
- Q. If a link lifter or arm were broken, what should be done?
A. Take off the disabled parts, block between the top of the link and link block, having the disabled link blocked down very nearly in full strokes. For safety, both the top and bottom of the disabled link should have blocks in its slot; the good link would be held in place by the reverse lever and should under no consideration be dropped down any farther than the disabled link was.
- Q. If the reverse lever or reach rod should break, what should be
done?
A. If either breaks, place an iron bar or suitable piece of material across the top of both frames, securely fastening it in position, then fasten the arm of the tumbling shaft to the bar. This will require the engine to be worked at about half cut-off; handle such part of the train as the road conditions would permit.
- Q. What should be done if the piston, piston rod, cross-head, main
rod or crank pin are broken or bent?
A. If a piston should break, would remove broken parts, disconnect valve stem, clamp valve in central position, and if moving piston would not damage cylinder, leave main rod up and proceed. If a piston rod, cross-head, main rod or crank pin are broken or bent, would take down the main rod, block the valve and cross-head; if piston rod is broken off at the cross-head, leave main rod up.
- Q. What should be done when there is a loose or lost cylinder key?
A. If the cylinder key is loose, it should be tightened up; if lost, something should be substituted. In case nothing solid can be found to take the place of the key, the engine should be run in light to avoid further damage.
- Q. What should be done if a safety valve spring or stud breaks?
A. The steam pressure should be reduced. With broken spring, screw the parts down solid or clamp the stem down. This can be done by laying a piece of scantling across the top of the valve, fastening each end to the hand rail on opposite sides of the engine in case of broken stud.
Would then raise steam pressure and proceed. Care should be taken to see that the other safety valves relieve the steam pressure properly.
- Q. How can an engine be brought in with a broken front end or stack?
A. By boarding up the front end to make it as near air tight as possible and using a barrel or a petticoat pipe in place of the stack, wiring it fast to the smoke-arch. Where a portion of the stack is inside the smoke-box the engine might steam without the barrel or petticoat pipe.
- Q. What should be done if the frame is broken between the main
driver and cylinder?
A. Either give up the train and come in light, or disconnect the engine on that side and come in with reduced tonnage, depending on how badly the engine pounds when working steam.
- Q. If the frame is broken back of the main driver?
A. Do not disconnect and do not try to pull a heavy train; it is safer to come in with light tonnage.
- Q. In case of broken side rods, what should be done?
A. Take down the broken rod and corresponding rod on the other side of the engine.
- Q. What can be done if the intermediate side rods were broken on a
consolidation engine having the eccentric on the axle ahead of the main wheel?
A. In this case the engine must be towed in. It is possible when the main pin is broken, so that all rods on one side are taken off, to leave the rods up on the other side and move the engine with her own steam, but very few roads will allow this, because engineers will be inclined to leave the main rod up on the disabled side to prevent engine catching on the center. If main rod is left up on the disabled side, the wheels will surely slip and wreck the rods on the other side.
- Q. Should one of the forward tire, main tire, intermediate tire,
back tire, or a trailer tire break, what must be done to bring the engine up?
A. Would run the wheel of the broken tire on a block in order to raise the wheel clear of the rail and the box up in the driving box jaws.
Remove the oil cellar and place a block between the driving journal and pedestal brace to carry the disabled wheel center clear of the rail.
Would also block up on top of the box of the wheel ahead or back as the case might be, in order to take the weight from the disabled wheel. It might not be necessary to take off any of the rods, but would run the engine light to the shop, giving special attention to lubrication of the disabled wheel and using extra precaution in entering side tracks and passing over frogs and switches. With the tire of a back driver or trailer wheel broken, it is usually necessary to swing the rear end of the engine from the tender to keep the rear end on the track.
With an inside radial journal, box on the trailer axle; for a broken trailer tire, both trailer wheels must be blocked and swung clear of the rail.
- Q. What is a good method of raising a wheel when jacks are not
available?
A. By raising the wheel on a hardwood block or iron wedge; a re-railing frog comes very handy for this purpose.
- Q. How can it be known when the wedges are set up too tight and the
driving box sticks, and in what manner can they be pulled down?
A. If wedges are set up too tight, it causes the boxes to stick and the engine to ride rough. Inspection of the engine when moving will locate the disabled box; usually this gets hot at once and the wedges should be immediately pulled down. Loosen the jam nuts on the wedge bolts and back them down; if the wedge is stuck very tight it may be necessary to run one or more of the wheels over a block; or to loosen the pedestal, brace bolt and allow the jaws to spread to release the box.
- Q. What are some of the various causes for pounds?
A. Wedges not properly adjusted, loose or worn driving box brasses, rod brasses not keyed or in need of reducing, loose side rod bushings or side rod connections, worn cross-heads, wrist pins, broken frame, loose cylinder key, loose piston on rod, or rod loose in cross-head, loose follower bolts or obstruction in the cylinder.
- Q. How may a pound in driving boxes, wedges or rod brasses be
located, and after locating what should be done?
A. Place the engine at half stroke on side to be tested. Do not set brake when testing for loose wedges or defective boxes; set brake when testing for other pounds. Reverse engine from forward to back gear under steam, noting the movement of the axle in the boxes, the driving boxes between the wedges, rod brasses on the pins and movement of cross-head between the guides. If possible would adjust wedges or rod brasses at once and report repairs needed at the terminal.
- Q. How locate loose follower bolts?
A. Shut off steam and allow engine to drift; there will be a pound in the cylinder when the loose follower bolt strikes a forward cylinder-head as the engine passes the forward center on that side; give engine steam while still moving and if the pound stops it is likely to be a loose or broken follower bolt. When working steam, the compression or pre-admission takes up the lost motion in the rod and connections, so the loose bolt does not strike the head; when shut off the piston travels the extra amount of this lost motion and the bolt strikes the head.
- Q. When should cross-heads or guides be reported to be lined?
A. When there is excessive lost motion between the cross-head and the top and bottom guides, or between the cross-head and the guide at the sides, or when the piston rod is not central between the guides.
- Q. When should driving box wedges be reported to be lined?
A. When they have been set up as far as possible and the boxes are still loose between the wedge and shoe. At this time would also report any excessive flange wear on any one particular tire.
- Q. When should rod brasses be reported to be reduced? When to be
lined?
A. Rod brasses should be reported reduced when they are larger than the pins and are pounding and cannot be keyed up properly. They should be reported to be lined when the key has been drawn or driven to its full length and the brasses do not close together or are too loose in the strap lengthwise of the rod.
- Q. When should lost motion between engine and tender be taken up?
A. When the lost motion becomes so great as to endanger the breaking of connections.
- Q. How do you proceed to pack a driving box equipped with a grease
cellar?
A. Remove the filling plate on the inside of the cellar. Pull down the indicators and follower plates, insert the grease between the follower plate and perforated plate; when full, replace the filling plate on the inside of the cellar and allow the spring and follower plate to force the grease through the perforated plate to the journal.
- Q. Please explain the principle on which an injector works.
A. With a lifting injector the steam valve is opened a small amount to furnish steam for the priming or starting jet. This forces the air in the body of the injector and top end of suction pipe out through the overflow valve, producing a partial vacuum in the body of the injector.
Atmospheric pressure in the tank then forces the water into the injector body. When it begins to come out through the overflow, a further movement of the steam valve opens the forcing valve wide, so a full supply of steam strikes the water at a high velocity and at the same time condensing. This action of the steam gives the water sufficient velocity to overcome the boiler pressure and pass into the boiler.
- Q. Explain the passage of steam from the boiler to the steam heat
pipe.
A. Steam is admitted to the steam heat pipe, in which there is placed a reducing valve through which it passes at reduced pressure, into the steam heat pipe under the entire length of the train. The reducing valve is located in the cab close to the steam heat throttle.
- Q. If the steam heat gauge shows proper pressure, but the steam
heat pipe pressure appears to be low, what should be done?
A. If the steam heat gauge is showing the correct pressure, there is an obstruction in the pipe somewhere, most likely in the steam heat hose, and this should be looked for and remedied; if the gauge is correct, then it is the reducing valve that is at fault and this should be readjusted, as well as the gauge.
- Q. What is the cause of failure with the second injector, and what
should be done to obviate this failure?
A. Lack of attention and failure to use every day will allow joints to work loose and boiler check to fill up with mud and scale. It should be tested every day and worked regularly so as to keep it in good working order.
- Q. If an injector stops working while on the road, what should you
do?
A. Would first ascertain if sufficient water was in the tender and tender valve open, and that water was cool enough in the tender so the injector would handle it. Would next see that no obstruction was in the feed pipe or strainer and that the feed pipe was free from leaks, and that the injector was getting a sufficient supply of steam. If the injector would not prime, would see whether overflow or heater valve could open wide, or if overflow pipe was obstructed.
If suction pipe was very hot would blow water back into tank and let suction fill with cold water. If possible, examine for obstruction in the steam priming tube and water tubes. If it would prime and fail to deliver water to the boiler, would see that the delivery tube was not obstructed and then look for trouble at the boiler check. An obstruction in the tubes would stop the injector working at once, while wear of the tubes or filling up with scale would affect the injector gradually.
- Q. What are the advantages of the combination boiler check and stop
valve?
A. A combination boiler check is fitted with a valve similar to a globe valve and can be closed at will. Its advantage is that the boiler pressure can be shut off from the check and the valve repaired without cooling the boiler. This hand-operated valve can be closed to prevent the boiler water passing back in case the check valve sticks up and allows the boiler water to pass back to the injector when not working.
- Q. How can a disconnected tank valve be opened without stopping?
A. Close the overflow or heater valve and turn steam back toward the tank; this will usually lift the valve from its seat or turn it around so it opens.
- Q. What comprises the steam heat equipment on a locomotive?
A. A globe valve throttle at the boiler, a reducing valve, a steam gauge connected to the steam heat pipe and the proper piping and hose connections.
- Q. What pressure is carried in the steam heat pipe, and how is it
controlled?
A. From twenty to sixty pounds in the train pipe, depending on the length of the train, and is controlled by the regulating valve.
- Q. What would you do in case the regulating valve failed to
operate?
A. In case the regulating valve would not admit sufficient steam to the train pipe, would take it apart and block the steam valve open. If the pressure ran up too high in the steam heat train pipe, would control it with the steam throttle at the boiler head.
- Q. How does the steam heat reducing valve control the pressure?
A. The inlet valve for live steam is opened and closed by the movement of a metallic diaphragm in the valve which is opened by spring pressure on one side and closed by steam pressure on the other side. To regulate this pressure, stiffen the spring to carry more, weaken it to carry less by turning the handle connected to this spring either up or down.
- Q. If steam heat gauge showed the required pressure and cars were
not being heated properly, how would you proceed to locate the trouble?
A. First note where the hand on the steam heat gauge stands when steam is shut off; if it does not drop back to zero see how much it lacks of this and note the rise of pressure shown by the gauge when steam is turned on. This is to test the gauge. If gauge is not correct, pay no attention to it, but send back steam enough to heat the train. Over sixty pounds will usually make the hose couplings on the cars rise up and leak at the joints.
- Q. When engine is detached from the train, what precaution should
you take to prevent freezing of the steam heat train pipe? What to prevent damage of steam heat hose?
A. Open steam throttle to allow a very little steam to pass into steam heat train pipe to prevent its freezing. If end of hose is liable to strike frogs or crossings, hang it up where it will be safe.
- Q. What constitutes abuse of an engine?
A. Improper use of injector by filling boiler at a rapid rate when drifting or standing in a siding, unless you have a heavy bright fire to heat the injected water to the boiler temperature as fast as it comes into the boiler. Excessive use of the blower, especially with a light fire or when cleaning the fire.
Improper attention to machinery, such as keeping parts not properly lubricated, rods not properly keyed, wedges not adjusted, carrying too much or too little water in the boiler, working water through the cylinders, allowing engine to slip unnecessarily, use of sand on one rail only or otherwise improperly; being careless in any way where care is required and not properly reporting the necessary work so it can be done promptly.
- Q. How are accidents and breakdown best prevented?
A. By inspection both at and after leaving terminals, frequently while on the road, keeping all parts properly adjusted, water in the boiler at the proper level and using good judgment in the handling of the engine and train. It is much better to use care and prevent accidents than to make repairs after they occur.
- Q. What are the duties of an engineman when leaving his engine at
the terminal?
A. Place her on the proper track to be turned over to the hostler, leave throttle closed securely, reverse lever in center notch, cylinder cocks open, and lubricator feeds to steam chest and cylinders closed. The boiler should be full of water and sufficient fire to maintain steam pressure until fire is knocked out. Call fireman's attention to anything of special importance. Inspect the engine very thoroughly, ascertain whether any tools or signals have been lost on the trip and make a full report of the condition of the entire locomotive.
- Q. What is the most important bolt or nut on the locomotive?
A. The loose one. It should be cared for immediately.
- Q. In reporting work on an engine, is it sufficient to do it in a
general way, such as saying: "Injector won't work," "lubricator won't work," "engine won't steam," "engine blows," etc.? Or would you report each special defect so it could be located after the engine was put in roundhouse or on designated track whether it had steam pressure in boiler or not?
A. No. Report all defects noticed so plainly that they can be located by the repair man without unnecessary work and whether there is steam in the boiler or not at the time repairs are to be made. If the engine blows, make a test to locate the blow and report it correctly. Also report any unusual feature in the operation of the engine during the trip.
=COMPOUND LOCOMOTIVES=
- Q. Wherein do compound locomotives differ from ordinary or simple
ones?
A. Simple engines take live steam from the boiler and after one expansion in a single cylinder it is exhausted to the atmosphere. A compound engine has two cylinders, sometimes one on each side of the locomotive; other types have four cylinders or two on each side of the locomotive. The live steam first passes into one cylinder, expanding down for a portion of its pressure, and then being allowed to pass into the second cylinder where it expands a second time, thus getting two expansions from each volume of live steam. Both simple and compound locomotives consist of two engines coupled to the same set of driving wheels. Balanced compounds have four sets of main rods and crank pins.
Mallet compounds have two complete sets of engines under one boiler.
- Q. Why is one cylinder on a compound locomotive called the
high-pressure cylinder and the other one a low-pressure cylinder?
A. The high-pressure cylinder takes that name because it works live steam direct from the boiler at high pressure. The low-pressure cylinder receives the steam after the first expansion and works with a low pressure. It is always larger than its companion high-pressure cylinder in order to get the same power from the low-pressure steam.
- Q. In the Schenectady two-cylinder compound, what is the duty of the
oil dash-pot?
A. It is intended to prevent the too rapid movement of the intercepting valve which might damage the valve or seat, and it is necessary that the dash-pot should be full of oil to make it work properly.
- Q. Explain how a Schenectady two-cylinder compound may be operated as
a simple engine.
A. To operate the compound as a simple engine, the separate exhaust valve is opened which will cause the intercepting valve to move and stay in position to allow the high-pressure cylinder to exhaust direct to the atmosphere and admits live steam at a reduced pressure to the low-pressure cylinder. This should be done when starting a train or when moving very slowly and about to stall on a grade. The engine should not be operated simple while running except when at low speed.
- Q. Explain how a two-cylinder compound is changed from simple to
compound.
A. Place the handle of the three-way cock or simpling valve in the cab so as to release the air from the cylinder of the separate exhaust valve. A coiled spring will then close this valve. This permits the exhaust steam of the high-pressure cylinder to accumulate in the receiver until sufficient pressure is obtained to force the intercepting valve into compounding position. This shuts off live steam from the low-pressure cylinder and allows exhaust steam from the high-pressure cylinder to feed through the receiver into the low-pressure steam chest.
- Q. How should a compound engine be lubricated?
A. One-third more oil should be fed to the high than the low-pressure cylinder, using more oil at high speed than at slow.
- Q. Why feed more oil to high than to a low-pressure cylinder?
A. Because some of the oil from the high-pressure cylinder follows the steam into the low-pressure cylinder.
- Q. How would you lubricate the valve of low-pressure cylinder if the
oil feed became inoperative on that side?
A. Feed an increased quantity through the oil pipe to the intercepting valve. Shut the engine off occasionally and cut into simple position.
Oil will then go direct from the intercepting valve into the low-pressure steam chest and cylinders. This would avoid going out on steam chest to oil by hand.
- Q. How much water should be carried in the boiler of a compound
locomotive?
A. A very moderate level, never allowing it to get so high that moist steam will pass through the cylinders, because for satisfactory service a compound engine should always have dry steam.
- Q. How should a compound locomotive be started with a long train?
A. In simple position with cylinder cocks open.
- Q. When drifting what should be the position of the separate exhaust
valve, the cylinder and port cocks?
A. Open position.
- Q. What will cause two exhausts of air to blow from the three-way
cock or simpling valve in the cab when the engine is being changed to compound?
A. A sticky exhaust valve. It does not move when air is first discharged. The second exhaust comes when it does move.
- Q. What does steam blowing at the three-way cock indicate?
A. The separate exhaust valve not seating properly caused by stuck valves, a weak or broken spring, or the packing rings of separate exhaust valve leaking.
- Q. What can be done if the engine will not operate compound when the
air pressure on the separate exhaust valve is released by the three-way cock?
A. The separate exhaust valve has failed to close. Try jarring it with a hammer on the front side, near the exhaust valve. With a bad case, take the valve out, clean it and replace, if not broken.
- Q. If the engine stands with high-pressure side on the dead center
and will not move when given steam, where is the trouble, and what may be done to start the engine? Why?
A. The intercepting valve is stuck in compound position, so live steam cannot get to the low-pressure cylinder. In a case of this kind, close the throttle, open cylinder and port cocks; when all pressure is relieved, use a bar to move forward the rod that works through the oil dash-pot, thus moving the valve to simple position and steam will pass to the low-pressure cylinder as soon as throttle is open. The engine will not start, because with the low-pressure piston on the quarter, steam must be admitted to its cylinder to start the engine.
- Q. In the event of a breakdown, how should one disconnect?
A. The same as a simple engine with separate exhaust valve open, so engine will work simple instead of compound.
- Q. What may be done to shut off steam pressure from the steam chest
and low-pressure cylinder?
A. To shut off steam from the low-pressure chest, pull out the rod that runs through the dash-pot as far as possible and fasten it in this position. Then open the separate exhaust valve.
- Q. Is it important that air be pumped up on a two-cylinder compound
before the engine is moved? Why?
A. Yes. Because the separate exhaust valve is opened by air pressure and the engine cannot be simpled without sufficient pressure.
- Q. How are the blows in a compound located?
A. The same as in a simple engine with the exception that any blow on the high-pressure side will not be heard when the separate exhaust valve is closed. A blow on the high-pressure side will increase the pressure in the low-pressure side, so relief valves will pop on low-pressure side when working compound with full throttle.
- Q. What should be done if high-pressure piston of a cross compound
is broken off the rod, or if the high-pressure or low-pressure cylinder head is broken?
A. Cover the ports on that side, open separate exhaust valve and run in; use live steam in low-pressure cylinder only, for the broken piston.
With broken cylinder head, would cover ports on that side. Open separate exhaust and run in with low-pressure side. Would not take down main rod, but would take out pop valves in both cylinder heads and see that the cylinder is properly oiled. For low-pressure head broken, would cover ports on that side, open separate exhaust valve and use high-pressure side; need not take down main rod, but would see that the cylinder is well oiled.
- Q. In the event of separate exhaust valves failing to work when
throttle is wide open, what can be done to assist in opening?
A. Ease throttle off very fine to reduce the receiver pressure; in a moment or two the separate exhaust valve should then move. If this did not work, would shut off entirely, even at the risk of stalling, as in that event the train could be started again with engine cut in simple.
- Q. If a transmission bar on a cross compound is broken, what would
you do for the right side? For the left side?
A. For right side would cover ports on that side, take out pop from cylinder head, open separate exhaust and run in with other cylinder. For left side, cover ports and fasten valve stem same as for right side.
Would leave main rods up, keep separate exhaust open in both cases and see that cylinder is well oiled.
- Q. In the event of a cross compound beginning to jerk badly and
cylinder head pops in low-pressure cylinder popping, where would you look for the trouble?
A. That either the high-pressure valve or piston packing was blowing live steam into the receiver and then into low-pressure steam chest. If possible would locate trouble and report accordingly.
- Q. If during a trip you found the piston valve rings of a cross
compound were broken, what would you do?
A. If nothing but rings were broken, would reduce boiler pressure about 25 per cent. and go on with my train if possible.
- Q. If piston valve on cross compound was broken so it became
necessary to remove it, what should you do?
A. Remove the broken piston valve, reduce boiler pressure to 100 pounds and proceed.
- Q. What is the difference between a Vauclain four-cylinder compound,
a four-cylinder tandem, a balanced and a Mallet compound in their arrangement of cylinders?
A. A Vauclain compound has two cylinders on each side, one above the other, and both piston rods connected to one cross-head. A four-cylinder tandem has four cylinders, the high pressure being ahead of the low pressure on each side, and both pistons connected to one piston rod and one cross-head. A balanced compound has four cylinders, the two high-pressure cylinders being between the frames, each having a main rod connected to a crank axle.
The two low-pressure cylinders are located outside the frame, each having a main rod and crank pin connected to the driving wheel center. A Mallet compound consists of two separate and independent engines, one fixed to the boiler, the other swinging from a center and sliding back and forth under the front end of the boiler. The rear engine works steam at high pressure; steam from this engine exhausts through a receiver pipe having flexible joints to the forward engine which works the steam at low pressure, then exhausts it to the front end and stack.
- Q. How many main steam valves has each type?
A. The Vauclain has one valve on each side, distributing steam to the high and low-pressure cylinder on that side. The four-cylinder tandem has two valves on each side, one for each of the two cylinders. A Baldwin balanced compound has two valves the same as the Vauclain. The American balanced compound has four valves, one for each cylinder, the two valves for one side of the engine being connected to one valve rod.
A Mallet compound has a separate valve for each cylinder the same as a simple locomotive.
- Q. How do you test for blow in high and low-pressure cylinder
packing for each type of compound engine?
A. Simple the engine if a cross compound, then make test the same as for a simple engine. For Vauclain four-cylinder compounds, test low pressure first. A blow past the low-pressure piston will show the same as on a simple engine; a blow past the high-pressure piston will make the engine stronger on that side when working a full throttle and the exhaust from the low-pressure cylinder will be heavier. To test the valve on either side, cover the ports. Broken packing rings in the steam valve will show a blow in one position and be tight in another.
For tandem compound, to test high-pressure piston packing, stand engine on the top quarter, lever in back gear, drivers blocked and starting valve closed; remove back indicator plug or open back cylinder cock of high-pressure cylinder. Steam coming from the back cylinder cock must get by the piston packing or by-pass or starting valve. Now put reverse lever ahead and try the other indicator plug or cylinder cock. If a leaky by-pass valve in the front end is the trouble, no steam will come through.
To test the low-pressure piston packing, place the engine in the same position, lever in position to admit steam into the front end of high-pressure cylinder. Open starting valve, remove back indicator plug of low-pressure cylinder and give engine steam; if steam comes from the indicator plug opening or open back cylinder cock, either packing or by-pass is leaking.
To determine which one, put reverse lever in another position, close back indicator plug and open forward one; if blow still continues, the packing rings are leaking or else both by-pass valves.
Would then inspect the by-pass valves.
- Q. How can the blow through sleeve packing between high and
low-pressure cylinder of the tandem compound be located?
A. Place the engine as before on the top quarter, put reverse lever in forward gear, see that starting valve is closed, block the drivers or set the brakes solid and open the throttle. Until the engine moves, unless there is a leak, no steam can get into the front side of the low-pressure cylinder. Remove the indicator plug in front end of the low-pressure cylinder for this test.
- Q. How test for piston packing blow with balanced compound?
A. For a Baldwin balanced compound to test the high-pressure piston packing, place the engine with the outside main pin on that side of the engine on the bottom quarter, the reverse lever in the forward notch, starting valve closed, set the brakes solid or block the drivers, remove the indicator plug in the front end of either the high or low-pressure cylinder. With throttle open this will admit steam to the back end of high-pressure cylinder. Steam coming out of this plug opening, will indicate a leak past the piston or the high-pressure valve.
If uncertain, next test the high-pressure valve by moving the reverse lever to the center notch. This should cover the ports and if the valve is tight the blow will stop. To test the low-pressure piston, place the engine in the same position with wheels blocked, starting valve open, back indicator plug out; when throttle is opened, the leaky packing will be shown by steam issuing from the plug opening.
If uncertain, the valve can be tested by bringing reverse lever to the center of quadrant, which will spot valve over port and if it is tight the blow will stop. In any compound engine a blow past the high-pressure packing tends to increase the pressure in the low-pressure cylinder. A blow past the low-pressure packing can always be heard at the exhaust, and is usually on both forward and back strokes, while a blow past the by-pass valves or valve bushings occurs at a certain part of a complete revolution only.
- Q. In case it was necessary to disconnect on one side of a compound
engine, how would you cover ports and hold valves in position?
A. The easiest way is to clamp the valve stem to hold valve in mid position; this should cover all ports. It may be necessary to take off head of piston valve chest and block in there.
- Q. Is it a disadvantage to work a compound engine in short cut-off?
Why?
A. Yes. If cut-off is too short the proper proportion of steam passing the throttle will not get to the low-pressure cylinder. The work should be divided between the two cylinders on same side.
- Q. In what way do the Mallet or articulated compounds differ from
other steam locomotives in the distribution of the steam?
A. Mallet compounds have two separate and complete engines under one boiler. The rear engine has a rigid connection to the back end of the boiler; this engine works boiler steam direct the same as a simple locomotive. Under the front end of the boiler is another engine so constructed that the entire front engine can move from side to side under the boiler, having a hinged connection at the front end of the rear engine to allow the locomotive to pass curves more easily. The front engine takes the exhaust steam from the rear engine through a flexible pipe or receiver and works it through a larger set of cylinders and thus compounds the steam.
From the low-pressure cylinders the steam is exhausted to the atmosphere through the stack.
- Q. How do you get the use of both engines when starting a train?
A. To get steam into the low-pressure cylinders before the high-pressure engine has exhausted, some types of the Mallet compound have a live steam pipe with a valve in the cab to admit boiler steam to the receiver pipe and thus get the use of the front engine in starting a train. The American Locomotive Company articulated compounds have an intercepting valve similar to the one used in the Richmond cross compound, located between the exhaust passage of the rear engine and the flexible receiving pipe of the front one.
This intercepting valve when in SIMPLE position, allows the high-pressure cylinders of the rear engine to exhaust directly to the stack instead of into the receiver, and feeds boiler steam at a reduced pressure into the receiver pipe for the low-pressure cylinders without giving any back pressure on the high-pressure pistons. This increases the power of the complete locomotive about 20 per cent.
When in compound position, the intercepting valve cuts off the supply of live steam to the receiver pipe and forces the exhaust steam to go to the low-pressure engine ahead.
- Q. How is the American articulated compound changed from compound to
simple, and back to compound again?
A. To work the locomotive simple, place the handle of operating valve in the cab to point toward the rear. This admits steam against the piston that operates the emergency exhaust valve and opens it. Exhaust steam from the high-pressure engine can pass to the exhaust nozzle instead of to the low-pressure engine. The intercepting valve then moves over so that live steam reduced to 40 per cent. of boiler pressure goes through the receiver pipe to the low-pressure engine. To work compound, place the handle of the operating valve to point forward.
This will exhaust the steam, holding the emergency exhaust valve open; a spring and the pressure of the steam exhausted from the rear engine will close the emergency exhaust valve and build up a pressure against the intercepting valve that will open it so exhaust steam from the rear engine will go to the forward one and at the same movement close the reducing valve so no more live steam goes to the receiver.
- Q. When is it necessary to use the operating valve to change the
locomotive from compound to simple, or from simple to compound?
A. When giving the engines steam to start, the intercepting valve should automatically go to simple position until exhaust steam from the rear engine builds up a receiver pressure that shifts the valve to compound; if it does not, use the operating valve. When moving less than four miles an hour or when about to stall on a grade, set the engines working simple; changing to compound when the danger of stalling is over or the speed is more than four miles an hour. If there is no intercepting valve to furnish live steam to the forward engine, open the starting valve to admit live steam to the receiver pipe and low-pressure engine.
- Q. If in starting the locomotive the forward engine does not take
steam, what is the trouble?
A. The reducing valve may be stuck shut on account of being dirty or stuck on the stem of the intercepting valve. In case the reducing valve is stuck shut, the head of the dash-pot can be taken off and the valve worked back and forth to loosen it. The intercepting valve should be liberally oiled just before starting and occasionally during long runs to keep it free from sticking.
- Q. Why does the Mallet compound have more power when working simple
than compound?
A. If a starting valve is used to admit live steam to the receiver pipe and thence to the low-pressure engine, this gives a higher pressure to the low-pressure cylinders. If an intercepting valve is used, the open emergency exhaust valve allows exhaust steam from the rear engine to go direct to the stack; this takes away the back pressure of the receiver steam from the high-pressure pistons, about 30 per cent. of the boiler pressure, and thus adds to the power of the rear engine.
The reducing valve when feeding live steam gives about 40 per cent. of boiler pressure to the low-pressure engine instead of the 30 per cent. it gets from the receiver; the added power of both engines working simple is about 20 per cent. over the compound operation.
- Q. What is the duty of the by-pass valves on
the sides of the low-pressure cylinders? Should they be kept clean of gum and grit?
A. These valves are connected to the steam ports at each end of the cylinders and open to allow air and steam to pass from one end of the cylinder to the other; away from the moving piston when the engine is drifting. If not kept clean they may stick open; when working steam the engine will blow badly; if they stick shut the engine will pound when drifting.
- Q. In what position should the reverse lever be when the steam is
shut off and the engine drifting?
A. Below three-quarters of full gear, so the valves will have nearly full travel.
- Q. Why should the power reversing gear of the Mallet compound always
have its dash-pot cylinder full of oil?
A. To prevent the too rapid movement of the reverse gear piston and its damage.
- Q. In what position should the engines stand to test for blows in
valves and piston packing?
A. Put the operating valve, or starting valve, in simple position. Spot the engine in the proper position and test each engine for blows the same as for a simple engine.
- Q. What power is used with Ragonnet or Baldwin power reverse gear?
A. Air pressure.
- Q. Can and should steam pressure be used?
A. Yes. However, steam should never be used except in an emergency when air is not available.
- Q. What precaution should be taken regarding steam check and
throttle?
A. That they are tight and check working properly, to insure that steam is kept from entering main reservoir, for if it should do so it would burn out the gaskets in the air brake equipment, allow moisture to accumulate, which would result in freezing and bursting of equipment as well as being dangerous.
- Q. What would cause the gear to fail to hold links in intended
cut-off, and allow them to raise and lower without operating valve in the cab being changed?
A. Leaks in main valve and piston packing.
=WALSCHAERT AND BAKER-PILLIOD VALVE GEARS=
- Q. Give a brief explanation of the Walschaert valve gear.
A. The Walschaert gear has an eccentric crank attached to the end of the main pin on each side of the locomotive, with an eccentric rod from this pin to the connection at the bottom end of the link. This eccentric is located so it serves for both forward and back motion. The link swings on a center trunnion and cannot be moved up and down as the Stephenson link, but the link block can be moved from one end of the link to the other to reverse the engine; or part way toward the center of the link to change the cut-off.
A radius rod connects the link block to the valve stem. There are two motions given to the valve stem, one from the link block which regulates the travel of the valve for the cut-off and reversing; the other motion is from a connection with the cross-head which gives the valve a positive motion to take care of the lap and lead. To give this motion there is used a combination lever or a lap and lead lever connected to a cross-head arm by the union link.
- Q. Is the Walschaert gear direct or indirect?
A. It is direct when the link block is below the center of the link; it is indirect when the link block is above the center of the link.
- Q. What are the principal differences in the location of the
Stephenson and Walschaert gears, and what advantages does this give the Walschaert?
A. The Stephenson gear is placed between the main frames and employs two eccentrics, with straps and rods on each side of the locomotive; one for forward and one for backward motion. The Walschaert gear is placed outside the driving wheels and frame, has but one eccentric, which is a simple arm connected to the outside end of the crank pin for both forward and back motion. The links are set above the wheels on a level with the steam chest, the combination lever next to the cross-head. This gives it an advantage of a better chance to inspect all parts, the eccentric connections are much lighter and direct, which makes them less liable to wear or breakdown, and the valve has a constant lead.
- Q. How is the lead affected by movement of the reverse lever with the
two gears?
A. With the Stephenson gear the lead increases as the reverse lever is hooked toward the center in both forward and back motion. With the Walschaert gear the lead is the same in all positions of the lever, so that the lever is used to reverse the engine or adjust the cut-off.
- Q. In reversing, how do the two gears differ as to the movement of
the link and link block?
A. With the Stephenson gear, when reversing, the link is raised and lowered, bringing the block which is not moved by the reverse lever under control of either the forward or back-up eccentric as is desired to move the engine the proper way. With the Walschaert gear the link is not moved by the reverse lever, but the link block is raised and lowered in the link; the position of the block above or below the center of the link controlling the direction of motion.
- Q. What would you disconnect if the eccentric crank, eccentric rod,
or the arm at the bottom of the link should break?
A. Would remove the broken parts, disconnect the link lifter from the radius rod and block the link block in the center of the link; the combination lever would then move the valve twice the amount of its lap and lead, which would be sufficient to provide for lubricating the cylinder.
- Q. If the main crank pin was broken?
A. Take down eccentric rod, eccentric crank, main rod and all connecting rods, block cross-head, disconnect from end of radius rod, chain it to running board and block steam valve to cover ports.
- Q. Broken cross-head pin, main rod, strap or brasses?
A. Take down main rod, block cross-head, disconnect front end of radius rod and chain to running board and block the valve to cover ports.
- Q. With a broken combination lever, union link or cross-head arms,
what would you do?
A. Would disconnect the forward end of the radius rod and secure it to the running board with a small chain, wire or rope, remove all broken parts, take off the combination lever, even if not broken, secure the valve in its central position, loosen cylinder head to provide for lubrication, leave up main rod and proceed on one side. If valve was blocked to open rear port slightly, this would provide for lubrication and the cylinder head need not be loosened.
- Q. If the radius rod on Walschaert gear is disabled, what should be
done?
A. If broken in front of the link block, take off the broken part by disconnecting from combination lever, take down eccentric rod, fasten valve to cover ports and proceed on one side. If broken back of the link block, block the link block in the desired position and proceed with both sides.
- Q. What would you disconnect with a Walschaert gear if a valve yoke
should break?
A. Disconnect the forward end of the radius rod, suspend it from running board, block the valve, provide for lubricating the piston and proceed.
- Q. How proceed with a broken reach rod?
A. Remove the reach rod, block links on lower side to hold them in running position for proper direction. Unless radius rod lifters can be uncoupled, leave a little slack in the blocking.
- Q. How can you tell without opening the steam chest if the valve
covers the port with Stephenson gear? With Walschaert gear?
A. Place the rocker shaft vertical with Stephenson gear. Place the combination lever vertical with reverse lever in mid gear so the link block is in the center of Walschaert link.
- Q. What is the Baker-Pilliod valve gear?
A. It is an outside gear with an eccentric crank, similar to the Walschaert gear, but without a reversing link. The motion is reversed by means of a reversing yoke instead of a link; the cut-off is changed in the same manner. It uses a combination lever connected with a union link to its cross-head arm. In case of breakdown remove the broken parts the same as described for Walschaert gear, blocking the reversing yoke, if necessary, in the proper position.
- Q. Is the Baker gear a direct or an indirect motion?
A. It is direct, going ahead for an inside admission and indirect backing up, and just the opposite for the outside admission type.
- Q. What parts of the Baker gear take the place of the link which is
used by the Stephenson or Walschaert motion?
A. The radius bars and reverse yoke.
- Q. What relation to the main pin is the eccentric crank set to?
A. The eccentric crank always follows the main pin.
- Q. Should the eccentric rod or eccentric crank break how is the
engine put in condition to proceed?
A. The disabled side can have lap and lead travel and a port opening equal to the lead for all cut-offs. First block the bell crank by using a "U" bolt (which should be provided) in the holes placed in the gear frame for this purpose. Throwing reverse lever in mid-gear will help to get bell crank in position to block. Second, take down broken parts.
Third, knock out back pin of short reach rod and throw reverse yoke in forward motion against gear frame.
- Q. What is to be done should a gear connection rod break?
A. Do the same as for a broken eccentric or crank.
- Q. What is to be done should the upper part of gear connection rod
break?
A. If break is close to the middle pin, do the same as for a broken eccentric rod and also tie lower end of gear connection rod to keep it from swinging. If break is near the top and below the jaw, first block the bell crank and wire the connection rod fast to radius bars. If break is through top jaw, do the same as for broken eccentric rod.
- Q. What is to be done should a radius bar break?
A. Do the same as for broken eccentric rod.
- Q. If the horizontal arm of bell crank should break?
A. Same as broken eccentric rod.
- Q. What is to be done should the vertical arm or bell crank break?
A. Take down union link combination lever and valve rod, then block valve over ports by using set-screw in valve stem cross-head provided for that purpose.
- Q. Should you break cross-head arm or union link, what would you do?
A. If rod be provided to secure lower end of the combination lever to guide yoke, remove broken parts and proceed with full train, working engine at long cut-off. Otherwise would remove broken parts, combination lever and valve rod, cover ports, and proceed on one side.
- Q. What do you do if a union link should break?
A. Same as for a broken cross-head arm.
- Q. What is to be done if a combination lever should break?
A. Tie combination lever plumb, same as for a broken cross-head arm, if it is possible. If not possible, take down the combination lever and valve rod and cover the ports.
- Q. What is to be done if a valve rod breaks?
A. Take down the broken parts and cover ports, leaving the rest of the gear intact.
- Q. What is to be done if a reverse yoke breaks?
A. If lugs for holding reach rod breaks, block yoke securely at whatever cut-off you wish to work the engine and take down the short reach rod.
If break is below the lugs, do the same as for broken eccentric rod.
- Q. What do you do if reach rod should break?
A. If short reach rod breaks, block the yoke at cut-off desired and wire fast so it cannot move. If main reach rod breaks, block between tumbling shaft arm and cross-tie brace, wiring same securely.
- Q. What is to be done if the engine breaks down other than valve
gear?
A. In this case do the same as for any other valve.
=SOUTHERN VALVE GEAR=
- Q. If the eccentric crank or eccentric rods fail?
A. Disconnect the eccentric rod from crank, radius hanger and transmission yoke, tie up the hanger and yoke, clamp valve central position and proceed.
- Q. If radius hanger fails?
A. Disconnect the hanger from rod and take down eccentric rod, clamp valve in central position and proceed.
- Q. If transmission yoke fails?
A. Disconnect from the eccentric rod and clamp valve in central position and proceed.
- Q. If horizontal arm of bell crank fails?
A. Disconnect the yoke from the eccentric rod, tie up to clear, clamp valve in central position and proceed.
- Q. If vertical arm to bell crank breaks?
A. Clamp valve in central position and proceed. Take the broken arm down if necessary.
- Q. If one auxiliary reach rod or reverse shaft arm fail?
A. Block both link blocks in same position of links, and in such a position as to give port opening enough to start train and control speed by throttle.
- Q. If main reach rod, or middle arm to reverse shaft fail? If both
auxiliary reach rods fail?
A. Block link blocks in full valve travel, controlling power and speed with the throttle.
=LUBRICATION=
- Q. What produces friction, and what is the result of excessive
friction?
A. Friction as considered in locomotive service is produced by one body being rubbed across the surface of another when they are held in contact by pressure, and the result of excessive friction is heat more or less intense and the destruction of the journal and its bearing or the roughening of the sliding surfaces.
- Q. What is lubrication and its object?
A. The object of lubrication is to interpose a film of oil, grease or some lubricant between the two surfaces that will prevent these rubbing surfaces from coming into too intimate contact.
- Q. What examinations should be made by the engineer to insure
successful lubrication?
A. See that all oil holes are open, cups filled and in good working order, the packing in cellars evenly put in and in contact with the journal. That waste on top of driving or truck boxes is in proper shape, also that grease cups are filled, and the plugs and jam nuts in good shape, and that the grease cellars contain sufficient grease for the next trip.
- Q. How should feeders of all oil cups be adjusted?
A. To feed as small a quantity of oil as possible and regularly to give perfect lubrication.
- Q. Why is it bad practice to keep engine oil close to boiler in warm
weather?
A. The oil is thinned to such a degree by the heat of the boiler that it runs off as soon as applied, and very often a hot bearing is the result.
- Q. In what manner would you care for a hot bearing if discovered on
the road?
A. Use as much time as available in cooling the same, making sure that all moving parts are free and carefully lubricated before proceeding.
- Q. What kind of oil should be used on hot bearings?
A. Use engine oil unless the temperature of bearing consumes it, when a small quantity of valve oil may be used while the bearing is warm enough to make this oil flow. The valve oil must be removed as soon as the bearing cools to prevent reheating.
- Q. At completion of trip what is necessary?
A. Close all adjustable feeds and examine all lubricated parts by contact with the hand to determine that they are not above running temperature.
- Q. How would you determine what boxes to report examined? Why not
report all boxes examined?
A. By placing the hand on driving box, on hub of engine truck wheel and on top of tender truck boxes nearest the brass, and would not report them examined unless the temperature of same was above running heat. It is not necessary to report all boxes examined, because they do not all give trouble at the same time. If this report was made, it would appear that a proper inspection had not been made and would result in unnecessary work and waste of material.
- Q. Why is it bad practice to disturb the packing on top of driving
and engine truck boxes with spout of oil can when oiling engine?
A. This packing is put on top of boxes to assist in keeping dirt and dust out of oil holes, also to aid in gradual lubrication from the top.
If this packing is disturbed it will permit dirt and grit to work into oil holes and on the bearings as well as feed the oil away too rapidly.
- Q. How do you adjust grease cups as applied to rods?
A. Screw down plug until you feel a slight resistance from the grease, stop when grease shows between brass and pin; this should be sufficient over the division.
- Q. Is it usual for pins to run warm when using grease?
A. Yes; grease does not work properly until it gets warm enough to flow readily over the bearing.
- Q. What effect does too much pressure produce?
A. Wastes grease and increases the friction until the surplus amount is worked out so the bearing runs free on its journal.
- Q. Is it necessary to use oil with grease on crank pins?
A. No.
- Q. When an engine is equipped with Elvin driving box lubricator, how
can you tell whether a sufficient amount of lubricant is in the grease receptacle?
A. The indicator wire fastened to the bottom of the grease cellar indicates the amount of grease left in the cellar.
- Q. Why should engine oil not be used on valves and cylinders?
A. Engine oil loses its lubricating qualities before it gets up to the temperature of the valves and cylinders when they are working steam.
- Q. At what temperature does engine oil lose its lubricating
qualities? At what temperature for valve oil?
A. Engine oil begins to separate and give off gas at 345 degrees F. The temperature of steam at 120 pounds is 350 degrees F., while valve oil has a flash test of 520 degrees F. The temperature of steam at 235 pounds is 431 degrees F., much lower than the flash test of valve oil.
- Q. How and by what means are valves, cylinders and the steam end of
air pumps lubricated?
A. By a sight-feed hydrostatic lubricator.
- Q. What is the principle on which a lubricator operates. How does
the oil get from the cup to the steam chest?
A. The lubricator is located in the cab so there is a gradual descent in the oil pipe from the lubricator to the steam chest. Above the oil reservoir is a condenser that is kept filled with water condensed from steam fed from the boiler. The pressure of this water comes on the oil in the oil tank below it, forcing oil through the sight-feed valves; it then passes up by the sight-feed glasses to the oil pipe and steam chest. The use of the glasses is to make the drop of oil visible as it leaves the sight-feed nipple so the amount of oil fed can be regulated.
Steam from the boiler fed to the lubricator at boiler pressure through the equalizing tubes balances the pressure which comes from the steam chest when the engine is working steam.
- Q. How should the lubricator be filled?
A. First close all valves connected with the lubricator, open drain plug and remove filling plug, allowing water to escape until oil appears with it. Drain plug should then be closed. Fill the oil tank in the usual way, being careful not to overflow it; then replace filling plug.
If the supply of oil is insufficient to fill the lubricator, water can be used to finish it, as the lubricator will begin feeding sooner when filled full.
- Q. After filling lubricator, what should be done?
A. Open the steam throttle to the lubricator wide, then carefully open the water valve, but do not open the feeds until sure the chamber in the glass is filled with water.
- Q. How long before leaving terminal should the feed valves be
opened? Why?
A. About fifteen minutes; this time is necessary to allow oil to feed through the oil pipe and reach the steam chests.
- Q. How many drops should be fed per minute?
A. From one to seven, timed by the watch, depending on conditions.
Cylinders of large size require more oil than smaller ones.
- Q. If lubricator feeds regularly when working steam and too rapidly
after shutting off, what is the trouble?
A. The opening in the choke plug at the lubricator or through the steam valves at the steam chest is too large and should be reduced to the proper size by applying new chokes or valves.
- Q. When valves appear dry while using steam and the lubricator is
working all right, what would you do to relieve these conditions?
A. Ease off throttle for a few seconds to reduce the steam chest pressure and drop the reverse lever a few notches to give the valve a longer travel; oil held in the pipes will then flow down.
=FEDERAL REGULATIONS=
=For Inspection of Locomotive Boilers and Safety Appliances=
- Q. What is the purpose of the federal rules and regulations for
inspection of locomotive boilers?
A. So that all railroads operating under the laws of the United States government, would be obliged to maintain their boilers in a safe working condition.
- Q. What is the purpose of the quarterly and monthly interstate
inspection cards placed in the cab of the locomotive?
A. So that the federal inspector or engineer may see that the locomotive boiler has received its monthly or quarterly inspection.
- Q. What constitutes a safety appliance, as applied to a locomotive?
A. Any appliance that is placed on a locomotive for the purpose of protecting the employees from personal injury.
- Q. Name some of the safety appliances found on a locomotive?
A. Shield for tubular glass lubricators, also shields for water glass, automatic couplers, with lever attachments, air brakes, etc.
- Q. In what condition should safety appliances be maintained?
A. They should be maintained in first class condition.
- Q. What should be done in event of any of the safety appliances being
damaged while engine is in service so as to render it unsafe?
A. Warn all employees whose duties require them to work around the locomotive of its unsafe condition, then make report to those in authority so that it may be taken out of service until repairs are made.
- Q. What effort should be made on the part of the engineer to prevent
persons using a safety appliance which he knows is damaged and unsafe?
A. He should use such precaution as in his judgment would protect from injury all persons who are on or around the locomotive.
- Q. What is the duty of the engineer in event of his discovering a
safety appliance which is in an unsafe condition when taking an engine from roundhouse territory?
A. He should report at once to the person in authority so that necessary repairs may be made before engine goes into service.
=PYLE-NATIONAL ELECTRIC HEADLIGHT=
- Q. Why are electric headlights applied to locomotives?
A. Electric headlights are applied to locomotives so that the engineer may have a clear view of the track for enough ahead of the train to enable him to protect the company's property in his charge.
- Q. How far ahead of the engine should the arc headlight illuminate
the track?
A. Not less than from fifteen to twenty telegraph poles.
- Q. State how you would focus the lamp.
A. First, would adjust back of the reflector so front edge of reflector will be parallel with front edge of case. Second, adjust the lamp to have point of copper electrode as near the center of reflector as possible with carbons as near the center of the chimney holes as you can set them. Third, have the locomotive on straight track. Now move the base of the lamp around until you get a parallel beam of white light straight down the center of the track, then tighten the lamp down.
- Q. If the light throws shadows upon the track, is it properly
focused?
A. No.
- Q. If the light is properly focused, that is, if the rays are leaving
the reflector in parallel lines, but the light does not strike the center of the track, what should be done?
A. When the light rays are thrown out in parallel lines and they do not strike the center of the track, it denotes that the headlight case is not set straight with the engine, and the entire case on base board must be shifted until the shaft of light strikes the track as desired.
- Q. What can you do to insure a good and unfailing light for the
entire trip?
A. By carefully inspecting the entire equipment before departing on each trip, and know that there are no wires with insulation charred or worn off, that all screws and connections are tight, commutator clean and brushes set in brush holder in proper manner. Carbon in lamp of sufficient length to complete trip, and that the carbon will feed through the clutch freely and rests central over the copper electrode.
Copper electrode cleaned off, oil in both bearings and see that steam does not blow at stuffing box gland.
- Q. What kind of oil and how much would you use in the bearings of the
electric headlight equipment?
A. Would use the best grade of black or engine oil furnished for both bearings and only enough oil in oil cellar that the revolving loose oil ring may trail through the oil. When bearings are supplied with oil cups, use a heavy oil such as good engine or valve oil.
- Q. Why should you not use valve oil in these bearings?
A. Valve oil cannot be used successfully in the main bearing because of its heavy body. Valve oil could not be carried up to shaft by the oil ring in cold weather, as the ring will not revolve.
- Q. What is the most vital part of the dynamo?
A. The commutator.
- Q. What care or attention should be given the commutator?
A. The commutator must be kept clean, free from dirt, and the mica must be kept filed a trifle below the surface of the copper bars.
- Q. What kind of a bearing should the brush have on the commutator?
A. Brushes should be fitted to have a bearing with the same contour as the commutator.
- Q. How are the brushes fitted?
A. Brushes are fitted by cutting a strip of No. 0 sandpaper about the width of the commutator surface (have the dynamo idle), place the strips of sandpaper under the brush, then pull the sandpaper from left to right; continue this process until the brush has been fitted to a true smooth bearing. Then trim about one-eighth inch off of the front edge of the brush.
- Q. Is it advisable to ever try to fit a brush with a file or knife?
A. Most emphatically no. You could not get a bearing across the brush no matter how hard you might try with either a file or a knife.
- Q. Why is it important to clean the scale off of the point of the
copper electrode each trip?
A. The scale on the copper electrode after it has cooled off is a non-conductor of current, and acts as a blind gasket between the carbon and the copper electrode. Unless this scale is removed, the current cannot pass between the points of carbon and electrode and you cannot, therefore, have a light. When the dynamo fields are compound wound, it is unnecessary to clean scale from copper electrode oftener than once a week, at which time copper electrode should be removed from holder and all scale cleaned off. (With compound wound dynamo fields the cab lamps will continue to burn when head-lamp is extinguished by lifting carbon by hand.)
- Q. How should the copper electrode be trimmed at the point?
A. The copper electrode should have about one-eighth inch surface on the contact point.
- Q. How far should the copper electrode project over the holder?
A. About one inch.
- Q. Should the electrode be raised up to one and one-half inches,
what might happen?
A. If the copper electrode was run at a point so near the clutch, the intense heat of the arc might do damage to the top carbon holder and clutch.
- Q. What regulation should be given to the tension spring No. 93 of
the lamp, and why?
A. This tension spring, No. 93, should be regulated when the current is off the lamp and should be adjusted only tight enough to pull the magnet yoke up against the top stop lug on the side of lamp column.
- Q. If this tension spring was tightened too tightly, what might
happen?
A. At usual speed between stations, the movement of the engine would impart an added resistance against the pull of the solenoid by the tension spring, which would shorten up the arc and dim down the light.
- Q. Is there anything else that could cause the light to dim down
when the engine is running fast?
A. Yes; if the spring No. 92-A that hold the heel of the clutch should be too weak, the heel of the clutch would be forced up by the motion of the locomotive; this would release the carbon which would fall to the point of the copper electrode, causing the light to dim down, or, if the clutch should be used until the sharp edge that grips the carbon should have become worn smooth or round, the same would occur.
- Q. If the light burns satisfactorily while the engine is in motion,
but goes out when engine is stopped, where would you find the trouble?
A. This trouble is most always found to be caused by the tension spring No. 93 being too weak, though if the dash-pot plunger has become corroded until it sticks in the dash-pot, the light will act the same as if the tension spring were too weak.
- Q. If the dash-pot should be found stuck, would you put oil in it?
A. Coal oil could be used to clean and cut the dirt out of the pot and from off the plunger, but after the dash-pot and plunger have been cleaned, all oil must be wiped off, for oil would cause the plunger to stick as well as collect dirt.
- Q. If the carbon of lamp should "jig or pound", what can be done to
stop it?
A. If the carbons pound the electrode, it is evidence that the iron armature No. 64 may be too far out of the solenoid, or the speed of the turbine engine may be too slow. This trouble can be remedied by adding another link to the suspension link, which has one end connected to the magnet yoke, the other end being connected to the iron armature No. 64.
If, however, when the arc is formed, it is found that the bottom end of iron armature No. 64 measures one-half inch from bottom of solenoid, the pounding is caused by the speed of turbine engine being too slow.
- Q. If the copper electrode was fusing, how would you know it?
A. When the copper electrode is fused, a green light is always given off.
- Q. What should be done when a green light is seen?
A. Immediately close off on the steam throttle until a white light re-appears.
- Q. What is the cause of the fusing of the copper electrode?
A. Usually too high speed of the armature, although should you connect the wires up wrong that the current flowing from the dynamo to the lamp should enter the lamp at the electrode instead of passing through the carbon first, you would get a green light and fuse the electrode.
- Q. What arrangements have been made so that you cannot connect the
wires wrong?
A. The positive binding posts, both at the dynamo and the lamp, have been provided with a much larger hole to receive the wire than has been made in the negative binding posts, and the ends of the positive wire should always be bent or doubled back, so that they will just enter the receptacle in the positive binding posts, but cannot be connected at the negative binding posts.
- Q. Should the copper electrode and holder become fused until no
longer serviceable while on the road, what would you do?
A. Would remove the damaged holder from the lamp and substitute either an iron bolt of sufficient length or a carbon, securing the improvised electrode in the bracket of lamp same as the electrode holder is held, only being sure that the end of the bolt or carbon comes up into the center of the reflector and did not rest on the base of reflector or lamp.
- Q. What is the difference between a series wound equipment and a
compound wound equipment, and what advantages are obtained from the use of the compound equipment.
A. With the series wound equipment, the incandescent cab lights burn only with the arc lamp, while with the compound machine the incandescent lamps are independent of the arc and can be used as desired.
- Q. If you were running along with your light burning steadily and
nicely, then suddenly the light began to flash badly and kept it up, where would you look for the trouble?
A. Trouble would usually be found at one of the binding posts, where one of the binding post screws would be found loose.
- Q. If you were running along with light burning satisfactorily and
suddenly it went out, where would you be likely to find the trouble?
A. You would find that either the carbon had burned out, one of the lead wires had broken between the dynamo and the lamp, or one of the wires had gotten loose at the binding post and fallen out.
- Q. If the light goes out while you are between stations, what course
should an engineer pursue?
A. If the light goes out while you are between stations and an investigation cannot be made within a few minutes thereafter to determine the cause, the steam should be shut off from the turbine and the dynamo stopped until such time when the cause of failure can be determined.
- Q. Why is it essential to shut off steam and stop the equipment?
A. For the reason that if the failure was due to a short circuit, damage might be done to the coils or armature by overheating.
- Q. How does the equipment act when short-circuited?
A. When there is short circuit, the engine will labor heavily, run slow with a large volume of steam blowing at the exhaust, there will be no light shown either at the arc or cab lamps, and the carbon point and cab lights will only show a dull red or go entirely out.
- Q. How will the equipment act when the circuit is broken, either by
a broken disconnected wire or a burned-out carbon?
A. With a broken circuit the engine will run noiselessly and fast with very little steam blowing at exhaust and no light will be seen at the arc or on cab lights.
- Q. If the insulation on the cab wires is worn off until your two
wires can come together either directly or through the medium of some metallic substance, what would occur?
A. A short circuit would result that would put out all of your lights.
- Q. What should be done?
A. Wrap the exposed wire, if you can locate it, with a piece of waste, or if you cannot locate the short circuit, disconnect one of your cab wires from the dynamo. This would give you the benefit of the arc lamp and you can look for the trouble at your leisure.
- Q. If the light goes out when steam drops back fifteen to twenty
pounds, what is the trouble?
A. Either one of the governor valves is stuck shut, short bushing No. 18 in engine cab is worn badly, allowing wheel to drop away from the governor stand so steam passes around wheel to exhaust, or governor springs are too weak.
- Q. In this case what should be done?
A. Report of the action of the dynamo should be made upon the work book at the terminal.
- Q. If clutch rod No. 78-B should break while on the road, what could
be done to get use of the lamp?
A. A piece of wire could be used by fastening one end around the end of top lever No. 59, the other end being attached to clutch through eye.
- Q. If you should lose the clothespin holder or top carbon clutch,
what could be done to get the light?
A. Would fasten a wire around the carbon and top holder to keep carbon in line, being careful not to get the wire either too tight or too loose.
- Q. If you should lose the iron armature No. 64 in solenoid, what
could be done to get use of light?
A. Would use a common iron bolt and suspend same by wire in magnet.
- Q. What would be the result if any of the levers of the lamp should
bind?
A. All levers of the lamp must work absolutely free and must not drag, for if they are not perfectly free the carbon cannot feed properly.
=Pyle-National Electric Incandescent Headlight=
- Q. What is meant by an incandescent headlight equipment?
A. A headlight having an electric incandescent lamp in the reflector in place of the usual oil or acetylene gas flame, and electric instead of oil cab lamps, the electricity being generated by a small combination steam-turbine and electric generator. Suitable wiring distributes the electric current.
- Q. In what manner does the incandescent headlight differ from the
arc headlight?
A. It is not so powerful. An incandescent or bulb type of lamp takes the place of the arc lamp in the headlight reflector. The current being less than is required for an arc, is supplied by a smaller turbine.
- Q. What type of incandescent lamp is used in the reflector?
A. A low voltage, gas filled bulb, containing a very compact or concentrated fillament.
- Q. Why cannot a standard or house type of lamp be successfully used
in the reflector?
A. Because the fillament or light-giving wire inside the bulb is not sufficiently compact or concentrated to reflect the light in the form of a beam. The voltage of the house lamp is also too high to be used on a locomotive installation.
- Q. How is the lamp held in place in the reflector?
A. By the usual socket, into which the lamp screws. The socket is a part of the focusing device, one type of which holds the lamp in a horizontal position, while in the other the lamp is held vertically or upright.
- Q. Before turning the steam into the turbine, what precautions
should be observed?
A. The turbo-generator should be lubricated by a small amount of black or engine oil, placed in the cup on the turbine or steam end. On the generator end, the oil should be maintained within one-half inch of the top of the hinge-cover cup; using black oil. The drainage of the steam end is cared for automatically by a three-eighth inch drain pipe without a valve. The pipe should be kept open.
- Q. How do you proceed when you wish to use the light?
A. Open the globe valve in the steam pipe to the turbo-generator, at least two turns. The water-glass, steam and air gauge lamps in the cab, and the number indicator lamp in the headlight case should light up as soon as the turbo-generator reaches full speed. A double-throw knife switch in the cab controls the headlight. In one position the switch gives the full brilliancy of the headlight. The opposite or "dimmer" position reduces the brilliancy about one-half. When the switch bar is in neither position the headlight is entirely out, and only the number lamp is burning.
The classification lamp, lubricator and order or reading lamp, are controlled by a small switch on the socket of each lamp.
- Q. For what purpose is the dimmer, and how does it operate?
A. It is to reduce the intensity of the headlight when locomotive is in yards or around stations. It consists of a small resistance tube in the wiring circuit, and with the cab switch in dimmer position, a portion of the current is converted into heat instead of light.
- Q. How is an incandescent headlight focussed?
A. By moving the lamp in its position in the reflector until the most brilliant and compact beam of light is obtained. If the beam does not strike the track centrally, or as high or low, the headlight case must be moved on its platform until the beam is properly directed. It is often necessary to raise the front or back of the case by shimming between the case and its platform in order to direct the beam of light the proper distance ahead of the locomotive.
- Q. What provision is made for moving or focussing the lamp in the
reflector?
A. When the lamp is mounted horizontally there are thumb screws by which the lamp may be moved sidewise, up and down, and forward and backward.
This mounting is called the "micrometer" device, because of the accuracy of adjustment. With the vertical mounting, a flat head thumb screw at the base of the lamp support releases the ball joint so that the lamp may be easily moved sidewise or forward and backward. To raise or lower the lamp, the thumb screw higher on the lamp stand must be loosened.
- Q. What causes a "black spot" in the illumination ahead of the
locomotive?
A. The lamp is out of focus, being too far ahead or back of the proper position in the reflector.
- Q. How would you remedy the following possible defects?
A. (a) =All lamps fail to burn.= If turbine is not running the wrong steam valve in the cab may have been opened, or there may be a second valve, closed, in the steam pipe. The screen on the governor valve in the turbine may be clogged. Remove brass cap at top of turbine and unscrew screen or strainer-cap.
(b) =Turbo-generator runs, but no lights.= Wires may be "short-circuited" (crossed) which will cause brushes to spark badly, and turbo-generator to pull hard. The "short" can usually be found by an occasional sparking or smoke at the point of trouble. Separate and protect wires when short is found. The brushes may be "cocked up" as left by some repair man. Open the dynamo door and see that the brushes bear on the copper commutator.
A wire may be loose at the dynamo binding posts (which may be seen when the dynamo door is open), or at the main switch in the cab. A main wire may have broken. (All locomotives are not equipped with fuse plugs.) A fuse plug may have become loose or burnt out. Replace with new fuse plugs or break an incandescent lamp and twist the leads in the base together, when the base may be screwed into the fuse plug socket, answering the purpose of a fuse plug, temporarily.
(c) =Headlight fails to burn.= Examine the wires between cab switch and head lamp for breaks or disconnections. Examine fuse plugs (which are sometimes in head lamp circuit only) and proceed as in (b) if trouble is found there. Headlight bulb may not be screwed in far enough to make contact in the socket, as the lock-sockets provided to prevent lamps loosening cause lamp to screw in hard. Lamp may have broken fillament.
Replace with proper type of lamp or use a cab lamp.
(d) =Lamps burn dim.= Steam valve not open wide enough. Boiler pressure too low. Brushes sparking badly on commutator of dynamo--due to poor contact. Governor or steam-valve of turbine improperly adjusted.
(e) =Lamps burn too brightly.= Improper turbine regulation. Throttle the steam valve in cab until lamps are reduced to proper brilliancy. Report all irregularities on arriving at terminal.
=SCHROEDER HEADLIGHT=
- Q. What is the speed of a Schroeder headlight dynamo?
A. About 2,800 revolutions per minute.
- Q. How is the speed altered?
A. By a governor in the turbine.
- Q. How would you proceed to change the speed of the governor?
A. Remove cover No. 3 and loosen lock nut No. 14 and turn nut No. 13 to the right to increase the speed and to the left to decrease it.
- Q. What is a short circuit?
A. A connection between the positive and negative wires of the dynamo without any resistance between.
- Q. How does the dynamo act when short-circuited?
A. It will run very slowly as it is under a heavy strain.
- Q. What would be the result if left to run under that strain?
A. The armature or fields would burn out.
- Q. What would you do if a short circuit developed while on the road?
A. Shut the steam off and remove the positive or right-hand wire of the cab circuit from the dynamo, start up and see if the headlight went to work properly; if not, replace the cab wire and remove the positive or left-hand wire and see if the cab lights burned properly. If such was the case, let it run, using the small incandescent light in the case for a headlight and report it at the roundhouse.
- Q. What is a volt?
A. The unit of pressure of
Edition notice Project Gutenberg source, credits & licence
The reading text above is the public-domain work. The Project Gutenberg header, production credits and licence are kept here as provenance rather than shown before the book.
Transcriber and production notes
Produced by Roger Frank and the Online Distributed Proofreading Team at http://www.pgdp.net
Front matter as received (title page, contents)
THE TRAVELING ENGINEERS' ASSOCIATION To Improve The Locomotive Engine Service of American Railroads
Header as received
The Project Gutenberg eBook of The Traveling Engineers' Association to Improve the Locomotive Engine Service of American Railroads
This eBook is for the use of anyone anywhere in the United States and
most other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg License included with this eBook or online
at www.gutenberg.org. If you are not located in the United States,
you will have to check the laws of the country where you are located
before using this eBook.
Title: The Traveling Engineers' Association to Improve the Locomotive Engine Service of American Railroads
Author: Traveling Engineers' Association
Release date: February 17, 2006 [eBook #17783]
Language: English
Other information and formats: www.gutenberg.org/ebooks/17783
Credits: Produced by Roger Frank and the Online Distributed
Proofreading Team at http://www.pgdp.netFull Project Gutenberg licence
Updated editions will replace the previous one—the old editions will
be renamed.
Creating the works from print editions not protected by U.S. copyright
law means that no one owns a United States copyright in these works,
so the Foundation (and you!) can copy and distribute it in the United
States without permission and without paying copyright
royalties. Special rules, set forth in the General Terms of Use part
of this license, apply to copying and distributing Project
Gutenberg™ electronic works to protect the PROJECT GUTENBERG™
concept and trademark. Project Gutenberg is a registered trademark,
and may not be used if you charge for an eBook, except by following
the terms of the trademark license, including paying royalties for use
of the Project Gutenberg trademark. If you do not charge anything for
copies of this eBook, complying with the trademark license is very
easy. You may use this eBook for nearly any purpose such as creation
of derivative works, reports, performances and research. Project
Gutenberg eBooks may be modified and printed and given away—you may
do practically ANYTHING in the United States with eBooks not protected
by U.S. copyright law. Redistribution is subject to the trademark
license, especially commercial redistribution.
START: FULL LICENSE
THE FULL PROJECT GUTENBERG™ LICENSE
PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK
To protect the Project Gutenberg™ mission of promoting the free
distribution of electronic works, by using or distributing this work
(or any other work associated in any way with the phrase “Project
Gutenberg”), you agree to comply with all the terms of the Full
Project Gutenberg License available with this file or online at
www.gutenberg.org/license.
Section 1. General Terms of Use and Redistributing Project Gutenberg
electronic works
1.A. By reading or using any part of this Project Gutenberg
electronic work, you indicate that you have read, understand, agree to
and accept all the terms of this license and intellectual property
(trademark/copyright) agreement. If you do not agree to abide by all
the terms of this agreement, you must cease using and return or
destroy all copies of Project Gutenberg electronic works in your
possession. If you paid a fee for obtaining a copy of or access to a
Project Gutenberg electronic work and you do not agree to be bound
by the terms of this agreement, you may obtain a refund from the person
or entity to whom you paid the fee as set forth in paragraph 1.E.8.
1.B. “Project Gutenberg” is a registered trademark. It may only be
used on or associated in any way with an electronic work by people who
agree to be bound by the terms of this agreement. There are a few
things that you can do with most Project Gutenberg electronic works
even without complying with the full terms of this agreement. See
paragraph 1.C below. There are a lot of things you can do with Project
Gutenberg electronic works if you follow the terms of this
agreement and help preserve free future access to Project Gutenberg
electronic works. See paragraph 1.E below.
1.C. The Project Gutenberg Literary Archive Foundation (“the
Foundation” or PGLAF), owns a compilation copyright in the collection
of Project Gutenberg electronic works. Nearly all the individual
works in the collection are in the public domain in the United
States. If an individual work is unprotected by copyright law in the
United States and you are located in the United States, we do not
claim a right to prevent you from copying, distributing, performing,
displaying or creating derivative works based on the work as long as
all references to Project Gutenberg are removed. Of course, we hope
that you will support the Project Gutenberg mission of promoting
free access to electronic works by freely sharing Project Gutenberg
works in compliance with the terms of this agreement for keeping the
Project Gutenberg name associated with the work. You can easily
comply with the terms of this agreement by keeping this work in the
same format with its attached full Project Gutenberg License when
you share it without charge with others.
1.D. The copyright laws of the place where you are located also govern
what you can do with this work. Copyright laws in most countries are
in a constant state of change. If you are outside the United States,
check the laws of your country in addition to the terms of this
agreement before downloading, copying, displaying, performing,
distributing or creating derivative works based on this work or any
other Project Gutenberg work. The Foundation makes no
representations concerning the copyright status of any work in any
country other than the United States.
1.E. Unless you have removed all references to Project Gutenberg:
1.E.1. The following sentence, with active links to, or other
immediate access to, the full Project Gutenberg License must appear
prominently whenever any copy of a Project Gutenberg work (any work
on which the phrase “Project Gutenberg” appears, or with which the
phrase “Project Gutenberg” is associated) is accessed, displayed,
performed, viewed, copied or distributed:
This eBook is for the use of anyone anywhere in the United States and most
other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg™ License included with this eBook or online
at www.gutenberg.org. If you
are not located in the United States, you will have to check the laws
of the country where you are located before using this eBook.
1.E.2. If an individual Project Gutenberg electronic work is
derived from texts not protected by U.S. copyright law (does not
contain a notice indicating that it is posted with permission of the
copyright holder), the work can be copied and distributed to anyone in
the United States without paying any fees or charges. If you are
redistributing or providing access to a work with the phrase “Project
Gutenberg” associated with or appearing on the work, you must comply
either with the requirements of paragraphs 1.E.1 through 1.E.7 or
obtain permission for the use of the work and the Project Gutenberg
trademark as set forth in paragraphs 1.E.8 or 1.E.9.
1.E.3. If an individual Project Gutenberg electronic work is posted
with the permission of the copyright holder, your use and distribution
must comply with both paragraphs 1.E.1 through 1.E.7 and any
additional terms imposed by the copyright holder. Additional terms
will be linked to the Project Gutenberg License for all works
posted with the permission of the copyright holder found at the
beginning of this work.
1.E.4. Do not unlink or detach or remove the full Project Gutenberg
License terms from this work, or any files containing a part of this
work or any other work associated with Project Gutenberg.
1.E.5. Do not copy, display, perform, distribute or redistribute this
electronic work, or any part of this electronic work, without
prominently displaying the sentence set forth in paragraph 1.E.1 with
active links or immediate access to the full terms of the Project
Gutenberg License.
1.E.6. You may convert to and distribute this work in any binary,
compressed, marked up, nonproprietary or proprietary form, including
any word processing or hypertext form. However, if you provide access
to or distribute copies of a Project Gutenberg work in a format
other than “Plain Vanilla ASCII” or other format used in the official
version posted on the official Project Gutenberg website
(www.gutenberg.org), you must, at no additional cost, fee or expense
to the user, provide a copy, a means of exporting a copy, or a means
of obtaining a copy upon request, of the work in its original “Plain
Vanilla ASCII” or other form. Any alternate format must include the
full Project Gutenberg License as specified in paragraph 1.E.1.
1.E.7. Do not charge a fee for access to, viewing, displaying,
performing, copying or distributing any Project Gutenberg works
unless you comply with paragraph 1.E.8 or 1.E.9.
1.E.8. You may charge a reasonable fee for copies of or providing
access to or distributing Project Gutenberg electronic works
provided that:
• You pay a royalty fee of 20% of the gross profits you derive from
the use of Project Gutenberg works calculated using the method
you already use to calculate your applicable taxes. The fee is owed
to the owner of the Project Gutenberg trademark, but he has
agreed to donate royalties under this paragraph to the Project
Gutenberg Literary Archive Foundation. Royalty payments must be paid
within 60 days following each date on which you prepare (or are
legally required to prepare) your periodic tax returns. Royalty
payments should be clearly marked as such and sent to the Project
Gutenberg Literary Archive Foundation at the address specified in
Section 4, “Information about donations to the Project Gutenberg
Literary Archive Foundation.”
• You provide a full refund of any money paid by a user who notifies
you in writing (or by e-mail) within 30 days of receipt that s/he
does not agree to the terms of the full Project Gutenberg™
License. You must require such a user to return or destroy all
copies of the works possessed in a physical medium and discontinue
all use of and all access to other copies of Project Gutenberg™
works.
• You provide, in accordance with paragraph 1.F.3, a full refund of
any money paid for a work or a replacement copy, if a defect in the
electronic work is discovered and reported to you within 90 days of
receipt of the work.
• You comply with all other terms of this agreement for free
distribution of Project Gutenberg™ works.
1.E.9. If you wish to charge a fee or distribute a Project
Gutenberg™ electronic work or group of works on different terms than
are set forth in this agreement, you must obtain permission in writing
from the Project Gutenberg Literary Archive Foundation, the manager of
the Project Gutenberg™ trademark. Contact the Foundation as set
forth in Section 3 below.
1.F.
1.F.1. Project Gutenberg volunteers and employees expend considerable
effort to identify, do copyright research on, transcribe and proofread
works not protected by U.S. copyright law in creating the Project
Gutenberg™ collection. Despite these efforts, Project Gutenberg™
electronic works, and the medium on which they may be stored, may
contain “Defects,” such as, but not limited to, incomplete, inaccurate
or corrupt data, transcription errors, a copyright or other
intellectual property infringement, a defective or damaged disk or
other medium, a computer virus, or computer codes that damage or
cannot be read by your equipment.
1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right
of Replacement or Refund” described in paragraph 1.F.3, the Project
Gutenberg Literary Archive Foundation, the owner of the Project
Gutenberg™ trademark, and any other party distributing a Project
Gutenberg™ electronic work under this agreement, disclaim all
liability to you for damages, costs and expenses, including legal
fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGE.
1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
defect in this electronic work within 90 days of receiving it, you can
receive a refund of the money (if any) you paid for it by sending a
written explanation to the person you received the work from. If you
received the work on a physical medium, you must return the medium
with your written explanation. The person or entity that provided you
with the defective work may elect to provide a replacement copy in
lieu of a refund. If you received the work electronically, the person
or entity providing it to you may choose to give you a second
opportunity to receive the work electronically in lieu of a refund. If
the second copy is also defective, you may demand a refund in writing
without further opportunities to fix the problem.
1.F.4. Except for the limited right of replacement or refund set forth
in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO
OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
1.F.5. Some states do not allow disclaimers of certain implied
warranties or the exclusion or limitation of certain types of
damages. If any disclaimer or limitation set forth in this agreement
violates the law of the state applicable to this agreement, the
agreement shall be interpreted to make the maximum disclaimer or
limitation permitted by the applicable state law. The invalidity or
unenforceability of any provision of this agreement shall not void the
remaining provisions.
1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
trademark owner, any agent or employee of the Foundation, anyone
providing copies of Project Gutenberg™ electronic works in
accordance with this agreement, and any volunteers associated with the
production, promotion and distribution of Project Gutenberg™
electronic works, harmless from all liability, costs and expenses,
including legal fees, that arise directly or indirectly from any of
the following which you do or cause to occur: (a) distribution of this
or any Project Gutenberg work, (b) alteration, modification, or
additions or deletions to any Project Gutenberg work, and (c) any
Defect you cause.
Section 2. Information about the Mission of Project Gutenberg
Project Gutenberg is synonymous with the free distribution of
electronic works in formats readable by the widest variety of
computers including obsolete, old, middle-aged and new computers. It
exists because of the efforts of hundreds of volunteers and donations
from people in all walks of life.
Volunteers and financial support to provide volunteers with the
assistance they need are critical to reaching Project Gutenberg’s
goals and ensuring that the Project Gutenberg collection will
remain freely available for generations to come. In 2001, the Project
Gutenberg Literary Archive Foundation was created to provide a secure
and permanent future for Project Gutenberg and future
generations. To learn more about the Project Gutenberg Literary
Archive Foundation and how your efforts and donations can help, see
Sections 3 and 4 and the Foundation information page at www.gutenberg.org.
Section 3. Information about the Project Gutenberg Literary Archive Foundation
The Project Gutenberg Literary Archive Foundation is a non-profit
501(c)(3) educational corporation organized under the laws of the
state of Mississippi and granted tax exempt status by the Internal
Revenue Service. The Foundation’s EIN or federal tax identification
number is 64-6221541. Contributions to the Project Gutenberg Literary
Archive Foundation are tax deductible to the full extent permitted by
U.S. federal laws and your state’s laws.
The Foundation’s business office is located at 41 Watchung Plaza #516,
Montclair NJ 07042, USA, +1 (862) 621-9288. Email contact links and up
to date contact information can be found at the Foundation’s website
and official page at www.gutenberg.org/contact
Section 4. Information about Donations to the Project Gutenberg
Literary Archive Foundation
Project Gutenberg™ depends upon and cannot survive without widespread
public support and donations to carry out its mission of
increasing the number of public domain and licensed works that can be
freely distributed in machine-readable form accessible by the widest
array of equipment including outdated equipment. Many small donations
($1 to $5,000) are particularly important to maintaining tax exempt
status with the IRS.
The Foundation is committed to complying with the laws regulating
charities and charitable donations in all 50 states of the United
States. Compliance requirements are not uniform and it takes a
considerable effort, much paperwork and many fees to meet and keep up
with these requirements. We do not solicit donations in locations
where we have not received written confirmation of compliance. To SEND
DONATIONS or determine the status of compliance for any particular state
visit www.gutenberg.org/donate.
While we cannot and do not solicit contributions from states where we
have not met the solicitation requirements, we know of no prohibition
against accepting unsolicited donations from donors in such states who
approach us with offers to donate.
International donations are gratefully accepted, but we cannot make
any statements concerning tax treatment of donations received from
outside the United States. U.S. laws alone swamp our small staff.
Please check the Project Gutenberg web pages for current donation
methods and addresses. Donations are accepted in a number of other
ways including checks, online payments and credit card donations. To
donate, please visit: www.gutenberg.org/donate.
Section 5. General Information About Project Gutenberg electronic works
Professor Michael S. Hart was the originator of the Project
Gutenberg concept of a library of electronic works that could be
freely shared with anyone. For forty years, he produced and
distributed Project Gutenberg eBooks with only a loose network of
volunteer support.
Project Gutenberg eBooks are often created from several printed
editions, all of which are confirmed as not protected by copyright in
the U.S. unless a copyright notice is included. Thus, we do not
necessarily keep eBooks in compliance with any particular paper
edition.
Most people start at our website which has the main PG search
facility: www.gutenberg.org.
This website includes information about Project Gutenberg,
including how to make donations to the Project Gutenberg Literary
Archive Foundation, how to help produce our new eBooks, and how to
subscribe to our email newsletter to hear about new eBooks.Source: Project Gutenberg ebook #17783. Public-domain status is recorded per item; the licence text above is reproduced unchanged.