
Gutenberg · ebook 17776
Transactions of the American Society of Civil Engineers, vol. LXX, Dec. 1910
by W. B. Gregory · English · public domain in the US
Transactions of the American Society of Civil Engineers, vol. LXX, Dec. 1910 by W. B. Gregory is an English public-domain text held from Project Gutenberg (ebook #17776). 1. Mathematical power (superscript) is rendered using a carat (^).
INSTITUTED 1852
TRANSACTIONS
Paper No. 1168
TESTS OF CREOSOTED TIMBER.
BY W. B. GREGORY, M. AM. SOC. C. E.
During the last few years a quantity of literature has appeared in which the treatment of timber by preservatives has been discussed. The properties of timber, both treated and untreated, have been determined by the Forest Service, United States Department of Agriculture, and through its researches valuable knowledge has come to engineers who have to deal with the design of wooden structures. There is very little information, however, regarding the effect of time on creosoted timber, and for this reason the results given herewith may prove of interest.
The material tested consisted of southern pine stringers having a cross-section approximately 6 by 16 in. and a length of 30 ft. For the purpose of testing, each beam was cut into two parts, each about 15 ft. long. This material had been in use in a trestle of a railroad near New Orleans for 26 years. The stringers were chosen at random to determine the general condition of the trestle. The timber had been exposed to the weather and subjected to heavy train service from the time it was treated until it was tested. The annual rainfall at New Orleans is about 60 in., and the humidity of the air is high.
In spite of these conditions, there was no appearance of decay on any of the specimens tested. The specifications under which the timber was treated were as follows:
TIMBER.
The timber for creosoting shall be long-leafed or southern pine. Sap surfaces on two or more sides are preferred.
Piles.--The piles shall be of long-leafed or southern pine, not less than 14 in. at the butt. They shall be free from defects impairing their strength, and shall be reasonably straight.
The piles shall be cleanly peeled, no inner skin being left on them. The oil used shall be so-called creosote oil, from London, England, and shall be of a heavy quality.
The treatment will vary according to the dimensions of the timbers and length of time they have been cut. Timbers of large and small dimensions shall not be treated in the same charge, neither shall timbers of differing stages of air seasoning, or the close-grained, be treated in the same charge with coarse or open-grained timbers.
The timbers shall be subjected first to live steam superheated to from 250 to 275° Fahr., and under a 30 to 40-lb. pressure. The live steam shall be admitted into the cylinders through perforated steam pipes, and the temperature shall be obtained by using superheated steam in closed pipes in the cylinders.
The length of time this steaming shall last will depend on the size of the timbers and the length of time they have been cut. In piles and large timbers freshly cut, as long a time as 12 hours may be required.
After the steaming is accomplished, the live steam shall be shut off and the superheated steam shall be maintained at a temperature of 160° or more and a vacuum of from 20 to 25 in. shall be held for 4 hours or longer, if the discharge from the pumps indicates the necessity.
Oil Treatment.--The temperature being maintained at 160° Fahr., the cylinders shall be promptly filled with creosote oil at a temperature as high as practicable (about 100° Fahr.). The oil shall be maintained at a pressure ranging from 100 to 120 lb., as experience and measurements must determine the length of time the oil treatment shall continue, so that the required amount of oil may be injected.
After the required amount of oil is injected, the superheated steam shall be shut off, the oil let out, the cylinders promptly opened at each end, and the timber immediately removed from the cylinder.
In the erection of timbers the sap side must be turned up, and framing or cutting of timbers shall not be permitted, if avoidable. All cut surfaces of timbers shall be saturated with hot asphaltum, thinned with creosote oil. The heads of piles when cut shall be promptly coated with the hot asphaltum and oil, even though the cut-off be temporary.
METHOD OF TESTING.
The tests were made on a Riehlé 100,000-lb. machine in the Experimental Engineering Laboratory of Tulane University of Louisiana. The machine is provided with a cast-iron beam for cross-bending tests. The distance between supports was 12 ft. The method of support was as follows: Each end of the beam was provided with a steel roller which rested on the cast-iron beam of the testing machine, while above the roller, and, directly under the beam tested, there was a steel plate 6 by 8 in. in area and 1 in. thick. The area was sufficiently great to distribute the load and prevent the shearing of the fibers of the wood. The head of the Riehlé machine is 10 in. wide.
A plate, 3/8 in. thick, 6 in. wide and 18 in. long, was placed between the head of the machine and the beam tested.
[Illustration: FIG. 1.--DEFLECTON CURVES BEAM I]
[Illustration: FIG. 2.--DEFLECTON CURVES BEAM II]
TABLE 1.--SUMMARY OF RESULTS OF TRANSVERSE TESTS OF BEAMS AT TULANE
UNIVERSITY, FEBRUARY 10TH TO MARCH 2D, 1909.
Columns in table:
- Number of beam.
- Top or butt of log.
- Width, in inches.
- Height, in inches.
- I = (bh^3)/12
- Actual at elastic limit.
- Maximum.
- At elastic limit.
- Maximum.
- At elastic limit.
- E = (Pl^3)/(48dI)
- Weight, in pounds per cubic foot.
===========================================================================+
| | b | h | I | LOADS: |S = (Plc)/(4I) | d, |
## | | | | | | |INCHES.|
| |------+-------+-------+-----------------+---------------+-------+
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
------+---+------+-------+-------+--------+--------+-------+-------+-------+
I | B | 6.28 | 15.94 | 2,120 | 22,000 | 45,900 | 2,975 | 6,200 | 0.41 |
I | T | 6.00 | 15.69 | 1,934 | 20,000 | 38,000 | 2,915 | 5,540 | 0.465 |
| | | | | | | | | |
II[A]| T | 6.37 | 15.81 | 2,098 | 20,000 | 43,450 | 2,722 | 5,918 | 0.380 |
II | B | 6.41 | 16.41 | 2,360 | 16,000 | 25,040 | 1,999 | 3,130 | 0.430 |
| | | | | | | | | |
III | T | 5.88 | 15.68 | 1,871 | 24,000 | 45,130 | 3,608 | 6,785 | 0.535 |
III | B | 5.88 | 15.90 | 1,965 | 21,000 | 35,190 | 3,054 | 5,120 | 0.515 |
| | | | | | | | | |
IV | T | 6.00 | 15.43 | 1,835 | 22,000 | 38,425 | 3,320 | 5,810 | 0.465 |
IV | B | 6.12 | 15.87 | 2,032 | 22,000 | 35,500 | 3,090 | 4,983 | 0.660 |
| | | | | | | | | |
V | B | 6.00 | 16.00 | 2,048 | 22,000 | 47,000 | 3,090 | 6,610 | 0.400 |
V[A]| T | 6.00 | 15.87 | 1,999 | 14,000 | 22,050 | 1,998 | 3,145 | 0.315 |
| | | | | | | | | |
VI[A]| B | 5.50 | 15.75 | 1,790 | 22,000 | 51,330 | 3,484 | 8,925 | 0.450 |
VI[A]| T | 5.87 | 15.62 | 1,865 | 20,000 | 44,000 | 3,013 | 6,627 | 0.410 |
| | | | | | | | | |
VII | B | 6.56 | 15.62 | 2,083 | 34,000 | 51,900 | 4,580 | 6,985 | 0.620 |
VII[A]| T | 6.22 | 15.62 | 1,975 | 20,000 | 49,000 | 2,845 | 6,970 | 0.380 |
===========================================================================+
[Footnote A: Failed in longitudinal shear.]
E | |
| |
-----------+ |
11 | 12 | Remarks.
-----------+------+---------------------------
1,575,000 | 50.2 | } Close-grained pine,
1,383,000 | 47.5 | } long-leaf.
| |
1,562,000 | 40.5 | } Coarse loblolly,
979,000 | 42.2 | } large knots.
| |
1,489,000 | 40.4 | } Close-grained, long-leaf
1,288,000 | 44.2 | } no knots.
| |
1,601,000 | 40.8 | } Loblolly, with
1,017,000 | 41.5 | } knots.
| |
1,670,000 | 47.2 | } Long-leaf yellow
1,382,000 | 42.1 | } pine.
| |
1,695,000 | 50.2 | } Long-leaf yellow
1,625,000 | 45.2 | } pine.
| |
1,637,000 | 43.7 | } Long-leaf yellow
1,658,000 | 40.2 | } pine.
==============================================
The deflection was measured on both sides of each beam by using silk threads stretched on each side from nails driven about 2 in. above the bottom of the beam and directly over the rollers which formed the supports. From a small piece of wood, tacked to the bottom of the beam at its center and projecting at the sides, the distance to these threads was measured. These measurements were taken to the nearest hundredth of an inch. The mean of the deflections was taken as the true deflection for any load.
[Illustration: FIG. 3.--DEFLECTON CURVES BEAM III]
[Illustration: FIG. 4.--DEFLECTON CURVES BEAM IV]
In computing the various quantities shown in Table 1, the summary of results, the load has been assumed as concentrated at the center of the beam. While it is true that the load was spread over a length of about 12 in., due to the width of the head of the machine and the plate between it and the beam tested, it is also true that there were irregularities, such as bolt-holes and, in some cases, abrasions due to wear, that could not well be taken into account. Hence, it was deemed sufficiently accurate to consider the load as concentrated.
Besides the horizontal bolt-holes, shown in the photographs, there were vertical bolt-holes, at intervals in all the beams. The latter were 7/8 in. in diameter, and in every case they were sufficiently removed from the center of the length of the beam to allow the maximum moment at the reduced section to be relatively less than that at the center of the beam. For this reason, no correction was made for these holes. The broken beams often showed that rupture started at, or was influenced by, some of the holes, especially the horizontal ones.
While some of the heavy oils of a tarry consistency remained, they were only to be found in the sappy portions of the long-leaf pine and in the loblolly (Specimens II and IV). Exposure in a semi-tropical climate for 26 years had resulted in the removal of the more volatile portions of the creosote oil. The penetration of the oil into the sap wood seemed to be perfect, while in the loblolly it varied from a fraction of an inch to 1-1/2 in. In the heart wood there was very little penetration across the grain. The timber had been framed and the holes bored before treatment. The penetration of the creosote along the grain from the holes was often from 4 to 6 in.
Circular 39 of the Forest Service, U. S. Department of Agriculture, entitled "Experiments on the Strength of Treated Timber," gives the results of a great many tests of creosoted ties, principally loblolly pine, from which the following conclusions are quoted:
"(1) A high degree of steaming is injurious to wood. The degree of
steaming at which pronounced harm results will depend upon the
quality of the wood and its degree of seasoning, and upon the
pressure (temperature) of steam and the duration of its
application. For loblolly pine the limit of safety is certainly 30
pounds for 4 hours, or 20 pounds for 6 hours." [Tables 3, 6, and
7.]
"(2) The presence of zinc chlorid will not weaken wood under static
loading, although the indications are that the wood becomes brittle
under impact." [Tables 3 and 4.]
[Illustration: FIG. 5.--DEFLECTON CURVES BEAM V]
[Illustration: FIG. 6.--DEFLECTON CURVES BEAM VI]
"(3) The presence of creosote will not weaken wood of itself. Since
apparently it is present only in the openings of the cells, and
does not get into the cell walls, its action can only be to retard
the seasoning of the wood." [Tables 3, 4, 5, and 6.]
[Illustration: FIG. 7.--DEFLECTON CURVES BEAM VII]
COMPARISONS.
A comparison of the results obtained with tests made on untreated timber is interesting, and to this end Tables 2 and 3, from Circular 115, Forest Service, U. S. Department of Agriculture, by W. Kendrick Hatt, Assoc. M. Am. Soc. C. E., are quoted. The tests made by the writer were from timber raised in Louisiana and Mississippi, while the tests quoted were from timber raised farther north. The number of tests was not sufficient to settle questions of average strength or other qualities.
It will be seen, however, that the treated timber 26 years old compares favorably with the new untreated timber.
[Illustration: PLATE I, FIG. 1.----SPECIMEN IN TESTING MACHINE, SHOWING METHOD OF SUPPORT.]
[Illustration: PLATE I, FIG. 2.--END VIEWS OF TESTED TIMBERS.]
TABLE 2.--BENDING STRENGTH OF LARGE STICKS.
Columns in table:
A: Reference number.
B: Number of tests.
C: Moisture, per cent.
D: Rings per inch.
E: Specific gravity, dry.
F: WEIGHT PER CUBIC FOOT, IN POUNDS.
G: As tested.
H: Oven dry.
I: Fiber stress at elastic limit, in pounds per square inch.
J: Modulus of rupture, in pounds per square inch.
K: Modulus of elasticity, in thousands of pounds per square inch.
L: Elastic resilience, in inch pounds per cubic inch.
M: Number failing by longitudinal shear.
LOBLOLLY PINE.
+========================================================================+ | | Locality| DIMENSIONS. | | | | | | | | | of +--------------+ Grade. |Condition | | | | | | A | Growth. |Section,|Span,| | of | | B | C | D | | | | in | in | |seasoning.| | | | | | | | inches.|feet | | | | | | | +---+---------+--------+-----+---------+----------+-------+---+-----+----+ | | | 6 by 7| | | | | | | | | | | 6 by 10| 10 | | | | | | | | 1 |South | 4 by 12| to | Square | Green |Average| | 48.0| 5.7| | |Carolina.| 6 by 16| 15.5| edge | |Maximum| 42| 92.1|11.7| | | | 8 by 14| | | |Minimum| | 30.2| 2.3| | | | 8 by 16| | | | | | | | +---+---------+--------+-----+---------+----------+-------+---+-----+----+ | | | 6 by 7| | | | | | | | | | | 4 by 12| 10 | | | | | | | | 2 |South | 6 by 10| to | Square |Partially |Average| | 27.7| 5.0| | |Carolina.| 6 by 16| 16 | edge |air dry. |Maximum| 18| 29.2| 8.2| | | | 8 by 16| | | |Minimum| | 25.5| 2.5| | | |10 by 16| | | | | | | | +---+---------+--------+-----+---------+----------+-------+---+-----+----+ | | | 6 by 7| 10 | | | | | | | | |South | 4 by 12| to | Square |Partially |Average| | 21.0| 5.6| | 3 |Carolina.| 6 by 10| 15 | edge |air dry. |Maximum| 19| 24.9|17.2| | | | 6 by 16| | | |Minimum| | 15.0| 2.7| +---+---------+--------+-----+---------+----------+-------+---+-----+----+ | | | | 6 | | |Average| | 22.4| 4.8| | 4 |Virginia.| 8 by 8| to | Square |Partially |Maximum| 12| 27.7| 8.8| | | | | 16 | edge |air dry. |Minimum| | 17.8| 2.5| +---+---------+--------+-----+---------+----------+-------+---+-----+----+ | | | | 6 | | |Average| | 64.0| 3.0| | 5 |Virginia.| 8 by 8| to | Square | Green |Maximum| 17|100.5| 4.0| | | | |15.5 | edge | |Minimum| | 38.8| 2.5| +---+---------+--------+-----+---------+----------+-------+---+-----+----+
LONG-LEAF PINE.
+---+---------+--------+-----+---------+----------+-------+---+-----+----+ | | | | | | |Average| | 25.0|13.7| | 6 |South | 6 by 8| 15 |Merchant-|Partially |Maximum| 22| 40.3|25.4| | |Carolina.|10 by 16| |able |air dry |Minimum| | 17.3| 6.2| +---+---------+--------+-----+---------+----------+-------+---+-----+----+ | | | | | | |Average| | 27.3|18.0| | 7 |Georgia. |10 by 12| 15 |Merchant-|Partially |Maximum| 22| 34.5|29.0| | | | | |able |air dry. |Minimum| | 20.0|11.0| +========================================================================+
+=====================================================================+ | | Locality| | F | | | | | | | | | of | +---------+ | | | | | | | A | Growth. | E | | | I | J | K | L | M | Remarks. |
| | | | G | H | | | | | | |
| | | | | | | | | | | | +---+---------+----+----+----+-----+------+-----+----+---+------------+ | | | | | | | | | | |Moisture | | | | | | | | | | | |above | | 1 |South |0.50|46.2|31.2|3,150| 5,580|1,426|0.45| |saturation | | |Carolina.|0.60|56.8|37.5|5,210| 8,460|1,920|0.99| 7 |point in | | | |0.40|35.6|25.0|1,675| 3,120| 905|0.07| |all cases. | | | | | | | | | | | | | +---+---------+----+----+----+-----+------+-----+----+---+------------+ | | | | | | | | | | | | | | | | | | | | | | | | | 2 |South |0.50|40.0|31.2|3,380| 5,650|1,435|0.45| |Moisture | | |Carolina.|0.55|43.7|34.4|4,610| 8,090|1,880|0.76| 0 |from 25 to | | | |0.45|35.6|28.1|2,115| 3,600|1,152|0.20| |30 per cent.| | | | | | | | | | | | | +---+---------+----+----+----+-----+------+-----+----+---+------------+ | | | | | | | | | | | | | |South |0.50|37.5|31.2|2,970| 5,690|1,340|0.39| |Moisture | | 3 |Carolina.|0.58|45.6|36.2|4,850| 8,100|2,040|0.69| 2 |less than | | | |0.41|31.2|25.6|1,730| 2,910| 906|0.10| |25 per cent.| +---+---------+----+----+----+-----+------+-----+----+---+------------+ | | |0.46|35.6|28.8|3,260| 5,180|1,180|0.51| | | | 4 |Virginia.|0.58|43.1|36.2|5,300| 8,950|1,728|1.05| 0 | | | | |0.37|30.0|23.1|1,280| 2,180| 606|0.13| | | +---+---------+----+----+----+-----+------+-----+----+---+------------+ | | |0.43|43.7|26.9|1,935| 3,490| 744|0.31| |Very rapid | | 5 |Virginia.|0.51|51.9|31.9|3,185| 4,720|1,193|0.78| 0 |growth; poor| | | |0.35|35.0|21.9| 956| 2,180| 357|0.12| |quality. | +---+---------+----+----+----+-----+------+-----+----+---+------------+
LONG-LEAF PINE.
+---+---------+----+----+----+-----+------+-----+----+---+------------+ | | |0.58|45.6|36.2|3,800| 7,160|1,560|0.53| | | | 6 |South |0.76|60.0|47.5|4,970|10,020|2,010|0.78| 9 | | | |Carolina.|0.50|39.4|31.2|2,220| 5,450|1,190|0.21| | | +---+---------+----+----+----+-----+------+-----+----+---+------------+ | | |0.69|54.7|42.9|5,581| 8,384|1,820| -- | |Excellent | | 7 |Georgia. |0.79| -- |49.4|9,600|11,410|2,920| -- | 6 |merchantable| | | |0.50| -- |31.4|3,547| 4,836|1,167| -- | |grade. | +=====================================================================+
TABLE 3.--LOBLOLLY PINE.--BENDING TESTS ON BEAMS SEASONED UNDER
DIFFERENT CONDITIONS.
(8 by 16-in. section; 13-1/2 to 15-ft. span.)
Columns in table:
A. Number of tests.
B. Fiber stress at elastic limit, in pounds per square inch.
C. Modulus of rupture, in pounds per square inch.
D. Longitudinal shear at maximum load, in pounds per square inch.
E. Modulus of elasticity, in thousands of pounds per square inch.
F. Percentage of moisture.
G. Rings per inch.
H. Weight per cubic foot, oven dry, in pounds.
I. Condition of seasoning.
| A | B | C | D | E | F | G | H | I
--------+---+-----+-----+-------+-----+----+----+----+--------------
Average | |3,580|5,480|364_{4}|1,780|23.2| 9.4|33.7| Air dry,
Maximum | 4 |4,070|6,600|440 |1,987|24.3|11.5|34.5| 3-1/2 months
Minimum | |3,090|5,000|327 |1,530|21.5| 8.0|32.5| in the open.
--------+---+-----+-----+-------+-----+----+----+----+--------------
Average | |4,512|5,060|338_{3}|1,685|20 | 7.7|33.9| Kiln dry,
Maximum | 5 |5,840|7,320|488 |1,790|22 |10.2|38.0| 6 days.
Minimum | |3,180|2,150|143 |1,410|18 | 4.7|27.7|
--------+---+-----+-----+-------+-----+----+----+----+--------------
Average | |4,331|6,721|493_{9}|1,688| -- | 7.7| -- | Air dry, 21
Maximum |12 |4,990|8,560|620 |2,002| -- | 9.5| -- | months under
Minimum | |3,110|5,160|380 |1,398| -- | 5.5| -- | shelter.
====================================================================
NOTE.--Figures written as subscripts to the figures for longitudinal shear indicate the number of sticks failing in that manner.
[Illustration: PLATE II.--SIDE VIEWS OF TESTED TIMBERS.]
TABLE 4.--LOAD AND DEFLECTION LOG. BEAM I.
Columns in table:
A: Load, in pounds.
B: Reading.
C: Total deflection.
D: Mean total deflection.
Date: February 26th, 1909. Date: February 24th, 1909. l = 12 ft.; l = 12 ft.; b (mean) = 6-9/32 in.; b (mean) = 6 in.; h (mean) = 15-15/16 in.; h (mean) = 15.69 in.; c = 7.97 in. c = 7.84 in.
Time = 1 hour.
| P | DEFLECTION, IN INCHES. || P | DEFLECTION, IN INCHES.
No.+------+----+----+----+----+-----++---------+----+----+----+----+-----
| A | B | C | B | C | D || A | B | C | B | C | D
---+------+----+----+----+----+-----++---------+----+----+----+----+-----
1 | 0 |1.86| 0 |1.88| 0 | 0 || 0 |1.83| 0 |1.86| 0 | 0
2 | 2,000|1.92|0.05|1.90|0.02|0.035|| 2,000 |1.87|0.04|1.90|0.04|0.04
3 | 4,000|1.96|0.10|1.94|0.06|0.080|| 4,000 |1.91|0.08|1.96|0.10|0.090
4 | 6,000|1.99|0.13|1.98|0.10|0.115|| 6,000 |1.96|0.13|2.00|0.14|0.135
5 | 8,000|2.03|0.17|2.02|0.14|0.155|| 8,000 |2.00|0.17|2.04|0.18|0.175
6 |10,000|2.05|0.19|2.06|0.18|0.185||10,000 |2.04|0.21|2.08|0.22|0.215
7 |12,000|2.10|0.24|2.09|0.21|0.225||12,000 |2.09|0.26|2.13|0.27|0.265
8 |14,000|2.13|0.27|2.13|0.25|0.260||14,000 |2.14|0.31|2.18|0.32|0.315
9 |16,000|2.17|0.31|2.16|0.28|0.295||16,000 |2.19|0.36|2.23|0.37|0.365
10 |18,000|2.20|0.34|2.20|0.32|0.330||18,000 |2.24|0.41|2.28|0.42|0.415
11 |20,000|2.24|0.36|2.25|0.37|0.365||20,000 |2.29|0.46|2.33|0.47|0.465
12 |22,000|2.28|0.42|2.28|0.40|0.410||22,000 |2.34|0.51|2.39|0.53|0.520
13 |24,000|2.32|0.46|2.32|0.44|0.450||24,000 |2.39|0.56|2.43|0.57|0.565
14 |26,000|2.36|0.50|2.36|0.48|0.490||26,000 |2.44|0.61|2.48|0.62|0.615
15 |28,000|2.40|0.54|2.39|0.51|0.525||28,000 |2.49|0.66|2.53|0.67|0.685
16 |30,000|2.43|0.57|2.44|0.56|0.565||30,000 |2.55|0.72|2.58|0.72|0.720
17 |32,000|2.48|0.62|2.48|0.60|0.610||32,000 |2.61|0.78|2.65|0.79|0.785
## 18 |34,000|2.52|0.68|2.53|0.65|0.655||34,000[B]|2.68|0.85|2.70|0.84|0.845
19 |36,000|2.56|0.70|2.56|0.68|0.690||36,000 |2.74|0.91|2.78|0.92|0.915
20 |38,000|2.61|0.75|2.62|0.74|0.745||38,000 | Broke.
21 |40,000|2.65|0.79|2.67|0.79|0.790||
22 |42,000|2.70|0.84|2.73|0.85|0.845||
23 |44,000|2.75|0.89|2.77|0.89|0.890||
||
37,500 lb., First Crack; ||
45,900 lb., Failed. ||
||
At Elastic Limit: Load, 22,000 lb.; ||At Elastic Limit: Load, 20,000 lb.;
deflection, 0.41 in.; || deflection, 0.465 in.;
S, 2,975 lb. || S, 2,975 lb.
||
Maximum: Load, 45,900 lb.; ||Maximum: Load, 38,000 lb.;
deflection,.....; || deflection,.....;
S, 6,209 lb. || S, 5,540 lb.
||
E = 1,575,000 lb. || E = 1,383,000 lb.
=========================================================================
[Footnote B: First crack.]
TABLE 4.--(Continued.)--LOAD AND DEFLECTION LOG. BEAM II.
Columns in table:
A: Load, in pounds.
B: Reading.
C: Total deflection.
D: Mean total deflection.
Date: February 20th, 1909. Date: -- l = 12 ft.; l = 12 ft.; b (mean) = 6.38 in.; b (mean) = 6.41 in.; h (mean) = 15.81 in.; h (mean) = 16.41 in.; c = 7.91 in. c = 8.20 in.
Time = 47.5 min.
| P | DEFLECTION, IN INCHES. || P | DEFLECTION, IN INCHES.
No.+------+----+----+----+----+-----++---------+----+----+----+----+-----
| A | B | C | B | C | D || A | B | C | B | C | D
---+------+----+----+----+----+-----++---------+----+----+----+----+-----
1 | 0 |1.65| 0 |1.68| 0 | 0 || 0 |1.86| 0 |1.87| 0 | 0
2 | 2,000|1.69|0.04|1.72|0.04|0.040|| 2,000 |1.91|0.05|1.92|0.05|0.05
3 | 4,000|1.73|0.08|1.77|0.09|0.085|| 4,000 |1.98|0.12|1.98|0.11|0.115
4 | 6,000|1.76|0.11|1.80|0.12|0.115|| 6,000 |2.05|0.19|2.02|0.15|0.170
5 | 8,000|1.80|0.15|1.83|0.15|0.150|| 8,000 |2.07|0.21|2.08|0.21|0.210
6 |10,000|1.83|0.18|1.86|0.18|0.180||10,000 |2.13|0.27|2.13|0.26|0.265
7 |12,000|1.87|0.22|1.90|0.22|0.220||12,000 |2.18|0.32|2.18|0.31|0.315
8 |14,000|1.91|0.26|1.94|0.26|0.260||14,000 |2.25|0.39|2.24|0.37|0.380
9 |16,000|1.95|0.30|1.98|0.30|0.300||16,000 |2.30|0.44|2.29|0.42|0.430
## 10 |18,000|1.98|0.33|2.02|0.34|0.335||18,000[C]|2.35|0.49|2.35|0.48|0.485
11 |20,000|2.03|0.38|2.06|0.38|0.380||20,000 |2.44|0.58|2.42|0.55|0.565
12 |22,000|2.07|0.42|2.10|0.42|0.420||22,000 |2.54|0.68|2.54|0.67|0.675
13 |24,000|2.11|0.46|2.14|0.46|0.460||25,040 | Failed
14 |26,000|2.15|0.50|2.18|0.50|0.500||
15 |28,000|2.18|0.53|2.22|0.54|0.535||
16 |30,000|2.23|0.58|2.26|0.58|0.580||
17 |32,000|2.27|0.62|2.30|0.62|0.620||
18 |34,000|2.32|0.67|2.35|0.67|0.670||
19 |36,000|2.37|0.72|2.40|0.72|0.720||
20 |38,000|2.42|0.77|2.45|0.77|0.770||
21 |40,000|2.48|0.83|2.50|0.82|0.825||
22 |42,000|2.53|0.88|2.56|0.88|0.880||
23 |43,450| Fracture. ||
24 |45,710| Failed. ||
||
At Elastic Limit: Load, 20,000 lb.; ||At Elastic Limit: Load, 16,000 lb.;
deflection, 0.38 in.; || deflection, 0.43 in.;
S, 2,722 lb. || S, 1,999 lb.
||
Maximum: Load, 43,450 lb.; ||Maximum: Load, 25,040 lb.;
deflection,.....; || deflection,.....;
S, 5,918 lb. || S, 3,130 lb.
||
E = 1,562,000 lb. || E = 979,000 lb.
==========================================================================
[Footnote C: First crack.]
TABLE 4.--(Continued.)--LOAD AND DEFLECTION LOG. BEAM III.
Columns in table:
A: Load, in pounds.
B: Reading.
C: Total deflection.
D: Mean total deflection.
Date: February 13th, 1909. Date: -- l = 12 ft.; l = 12 ft.; b (mean) = 5.88 in.; b (mean) = 5.88 in.; h (mean) = 15.63 in.; h (mean) = 15.9 in.; c = 7.82 in. c = 7.95 in.
Time = 45 min.
| P | DEFLECTION, IN INCHES. || P | DEFLECTION, IN INCHES.
No.+------+----+----+----+----+-----++---------+----+----+----+----+-----
| A | B | C | B | C | D || A | B | C | B | C | D
---+------+----+----+----+----+-----++---------+----+----+----+----+-----
1 | 0 |1.23| 0 |1.06| 0 | 0 || 0 |1.67| 0 |1.63| 0 | 0
2 | 2,000|1.27| .04|1.10|0.04|0.040|| 2,000 |1.70|0.03|1.68|0.05|0.040
3 | 4,000|1.32|0.09|1.13|0.07|0.080|| 4,000 |1.72|0.05|1.72|0.09|0.070
4 | 6,000|1.37|0.14|1.17|0.11|0.125|| 6,000 |1.82|0.15|1.78|0.15|0.150
5 | 8,000|1.42|0.19|1.22|0.16|0.175|| 8,000 |1.86|0.19|1.82|0.19|0.190
6 |10,000|1.47|0.24|1.26|0.20|0.220||10,000 |1.90|0.23|1.87|0.24|0.235
7 |12,000|1.51|0.28|1.31|0.25|0.265||12,000 |1.97|0.30|1.92|0.29|0.295
8 |14,000|1.55|0.32|1.35|0.29|0.305||14,000 |2.00|0.33|1.98|0.35|0.340
9 |16,000|1.60|0.37|1.40|0.34|0.355||16,000 |2.03|0.36|2.04|0.41|0.385
10 |18,000|1.64|0.41|1.44|0.38|0.395||18,000 |2.10|0.43|2.09|0.46|0.445
11 |20,000|1.68|0.45|1.49|0.43|0.440||20,000 |2.13|0.46|2.14|0.51|0.485
12 |22,000|1.72|0.49|1.54|0.48|0.485||22,000 |2.20|0.53|2.20|0.57|0.550
13 |24,000|1.78|0.55|1.58|0.52|0.535||24,000 |2.26|0.59|2.26|0.63|0.610
14 |26,000|1.82|0.59|1.64|0.58|0.585||26,000 |2.31|0.64|2.32|0.69|0.665
15 |28,000|1.88|0.65|1.68|0.62|0.635||28,000 |2.38|0.71|2.40|0.77|0.740
16 |30,000|1.92|0.69|1.73|0.67|0.680||30,000 |2.42|0.75|2.47|0.84|0.795
17 |32,000|1.97|0.74|1.79|0.73|0.735||32,000 |2.49|0.82|2.55|0.92|0.870
18 |34,000|2.02|0.79|1.85|0.79|0.790||34,000 |2.58|0.91|2.62|0.99|0.950
19 |36,000|2.07|0.84|1.90|0.84|0.840||
20 |38,000|2.13|0.90|1.97|0.91|0.915||
21 |40,000|2.20|0.97|2.03|0.97|0.970||
22 |42,000|2.27|1.04|2.11|1.05|1.045||
23 |44,000|2.37|1.14|2.21|1.15|1.145||
||
39,100 lb.
First Crack; ||22,000 lb. First Crack;
45,130 lb. Failed. ||35,190 lb.
Failed.
||
At Elastic Limit: Load, 24,000 lb.; ||At Elastic Limit: Load, 21,000 lb.;
deflection, 0.535 in.; || deflection, 0.515 in.;
S 3,608 lb. || S, 3,054 lb.
||
Maximum: Load, 45,130 lb.; ||Maximum: Load, 35,190 lb.;
deflection,.....; || deflection,.....;
S 6,785 lb. || S 5,120 lb.
||
E = 1,489,000 lb. || E = 1,288,000 lb.
==========================================================================
TABLE 4.--(Continued.)--LOAD AND DEFLECTION LOG. BEAM IV.
Columns in table:
A: Load, in pounds.
B: Reading.
C: Total deflection.
D: Mean total deflection.
Date: February 16th, 1909. Date: February 10th, 1909. l = 12 ft.; l = 12 ft.; b (mean) = 6.0 in.; b (mean) = 6.12 in.; h (mean) = 15.43 in.; h (mean) = 15.87 in.; c = 7.71 in. c = 7.93 in.
Time = 30 min.
| P | DEFLECTION, IN INCHES. || P | DEFLECTION, IN INCHES.
No.+------+----+----+----+----+-----++---------+----+----+----+----+-----
| A | B | C | B | C | D || A | B | C | B | C | D
---+------+----+----+----+----+-----++---------+----+----+----+----+-----
1 | 0 |2.28| 0 |2.05| 0 | 0 || 0 |1.44| 0 |1.58| 0 | 0
2 | 2,000|2.31|0.03|2.10|0.05|0.040|| 2,000 |1.50|0.06|1.64|0.06|0.06
3 | 4,000|2,34|0.06|2.14|0.09|0.075|| 4,000 |1.55|0.11|1.70|0.12|0.115
4 | 6,000|2.40|0.12|2.19|0.14|0.130|| 6,000 |1.62|0.18|1.76|0.18|0.180
5 | 8,000|2.43|0.15|2.23|0.18|0.165|| 8,000 |1.68|0.24|1.82|0.24|0.240
6 |10,000|2.47|0.19|2.28|0.23|0.210||10,000 |1.72|0.28|1.89|0.31|0.295
7 |12,000|2.51|0.23|2.32|0.27|0.250||12,000 |1.80|0.36|1.94|0.36|0.360
8 |14,000|2.54|0.26|2.37|0.32|0.290||14,000 |1.85|0.41|2.00|0.42|0.415
9 |16,000|2.59|0.31|2.41|0.36|0.335||16,000 |1.90|0.46|2.06|0.48|0.470
10 |18,000|2.62|0.34|2.45|0.40|0.370||18,000 |1.98|0.54|2.13|0.55|0.545
11 |20,000|2.68|0.40|2.50|0.45|0.425||20,000 |2.03|0.59|2.19|0.61|0.600
12 |22,000|2.72|0.44|2.54|0.49|0.465||22,000 |2.09|0.65|2.25|0.67|0.660
13 |24,000|2.78|0.50|2.60|0.55|0.525||24,000 |2.15|0.71|2.33|0.75|0.730
14 |26,000|2.82|0.54|2.65|0.60|0.570||26,000 |2.23|0.79|2.42|0.84|0.815
15 |28,000|2.87|0.59|2.69|0.64|0.615||28,000 |2.32|0.88|2.49|0.91|0.895
16 |30,000|2.91|0.63|2.74|0.69|0.660||30,000 |2.42|0.98|2.62|1.04|1.010
17 |32,000|2.97|0.69|2.78|0.73|0.710||32,000 |2.56|1.12|2.74|1.16|1.140
18 |34,000|3.01|0.73|2.85|0.80|0.765||34,000 |2.67|1.23|2.87|1.29|1.265
19 |36,000|3.07|0.79|2.90|0.85|0.820||
20 |38,000|3.14|0.86|2.98|0.93|0.895||
||
34,000 lb.
First Crack; ||28,360 lb. Cracked;
38,425 lb.
Failed. ||35,500 lb, Failed.
||
At Elastic Limit: Load, 22,000 lb.; ||At Elastic Limit: Load, 22,000 lb.;
deflection, 0.465 in.; || deflection, 0.66 in.;
S 3,320 lb. || S, 3,090 lb.
||
Maximum: Load, 38,425 lb.; ||Maximum: Load, 35,500 lb.;
deflection,.....; || deflection,.....;
S 5,810 lb. || S 4,983 lb.
||
E = 1,601,000 lb. || E = 1,017,000 lb.
==========================================================================
TABLE 4.--(Continued.)--LOAD AND DEFLECTION LOG. BEAM V.
Columns in table:
A: Load, in pounds.
B: Reading.
C: Total deflection.
D: Mean total deflection.
Date: -- Date: February 27th, 1909. l = 12 ft.; l = 12 ft.; b (mean) = 6 in.; b (mean) = 6 in.; h (mean) = 16 in.; h (mean) = 15.87 in.; c = 8 in. c = 7.94 in.
Time = 40 min.
| P | DEFLECTION, IN INCHES. || P | DEFLECTION, IN INCHES.
No.+------+----+----+----+----+-----++---------+----+----+----+----+-----
| A | B | C | B | C | D || A | B | C | B | C | D
---+------+----+----+----+----+-----++---------+----+----+----+----+-----
1 | 0 |1.97| 0 |1.37| 0 | 0 || 0 |1.31| 0 |1.25| 0 | 0
2 | 2,000|2.01|0.04|1.40|0.03|0.035|| 2,000 |1.37|0.06|1.31|0.06|0.06
3 | 4,000|2.06|0.09|1.43|0.06|0.075|| 4,000 |1.41|0.10|0.36|0.11|0.105
4 | 6,000|2.08|0.11|1.47|0.10|0.105|| 6,000 |1.46|0.15|0.40|0.15|0.150
5 | 8,000|2.11|0.14|1.50|0.13|0.135|| 8,000 |1.49|0.18|0.45|0.20|0.190
6 |10,000|2.16|0.19|1.54|0.17|0.180||10,000 |1.54|0.23|1.49|0.24|0.235
7 |12,000|2.19|0.22|1.57|0.20|0.210||12,000 |1.58|0.27|1.53|0.28|0.275
8 |14,000|2.22|0.25|1.61|0.24|0.245||14,000 |1.62|0.31|1.57|0.32|0.315
9 |16,000|2.25|0.28|1.65|0.28|0.280||16,000 |1.68|0.37|1.65|0.40|0.385
10 |18,000|2.29|0.32|1,69|0.32|0.320||18,000 |1.78|0.41|1.71|0.46|0.435
11 |20,000|2.32|0.35|1.73|0.36|0.355||20,000 |1.99|0.68|1.97|0.72|0.700
12 |22,000|2.36|0.39|1.78|0.41|0.400||
13 |24,000|2.39|0.42|1.83|0.46|0.440||
14 |26,000|2.42|0.45|1.85|0.48|0.465||
15 |28,000|2.47|0.50|1.90|0.53|0.515||
16 |30,000|2.50|0.53|1.95|0.58|0.565||
17 |32,000|2.54|0.57|1.99|0.62|0.595||
18 |34,000|2.59|0.62|2.04|0.67|0.645||
19 |36,000|2.63|0.66|2.09|0.72|0.690||
20 |38,000|2.68|0.71|2.17|0.80|0.755||
21 |40,000|2.73|0.76|2.21|0.84|0.800||
22 |42,000|2.80|0.83|2.30|0.93|0.880||
23 |44,000|2.90|0.93|2.40|1.03|0.980||
||
25,000 lb.
Slight Crack; ||20,000 lb. First Crack;
47,000 lb. Failed. ||22,050 lb.
Failed.
||
At Elastic Limit: Load, 22,000 lb.; ||At Elastic Limit: Load, 14,000 lb.;
deflection, 0.40 in.; || deflection, 0.315 in.;
S, 3,090 lb. || S, 1,998 lb.
||
Maximum: Load, 47,000 lb.; ||Maximum: Load, 22,050 lb.;
deflection,.......; || deflection,.......;
S, 6,610 lb. || S, 3,145 lb.
||
E = 1,670,000 lb. || E = 1,382,000 lb.
=========================================================================
TABLE 4.--(Continued.)--LOAD AND DEFLECTION LOG. BEAM VI.
Columns in table:
A: Load, in pounds.
B: Reading.
C: Total deflection.
D: Mean total deflection.
Date: February 12th, 1909. Date: February 13th, 1909. l = 12 ft.; l = 12 ft.; b (mean) = 5.5 in.; b (mean) = 5.87 in.; h (mean) = 15.75 in.; h (mean) = 15.62 in.; c = 7.88 in. c = 7.81 in.
Time = 40 min.
| P | DEFLECTION, IN INCHES. || P | DEFLECTION, IN INCHES.
No.+------+----+----+----+----+-----++---------+----+----+----+----+-----
| A | B | C | B | C | D || A | B | C | B | C | D
---+------+----+----+----+----+-----++---------+----+----+----+----+-----
1 | 0 |1.22| 0 |1.30| 0 | 0 || 0 |1.28| 0 |1.30| 0 | 0
2 | 2,000|1.26|0.04|1.34|0.04|0.04 || 2,000 |1.30|0.02|1.35|0.05|0.035
3 | 4,000|1.29|0.07|1.38|0.08|0.075|| 4,000 |1.36|0.08|1.39|0.09|0.085
4 | 6,000|1.33|0.11|1.42|0.12|0.115|| 6,000 |1.40|0.12|1.44|0.14|0.130
5 | 8,000|1.37|0.15|1.47|0.17|0.160|| 8,000 |1.43|0.15|1.47|0.17|0.160
6 |10,000|1.42|0.20|1.51|0.21|0.205||10,000 |1.47|0.19|1.51|0.21|0.200
7 |12,000|1.45|0.23|1.55|0.25|0.240||12,000 |1.51|0.23|1.56|0.26|0.245
8 |14,000|1.50|0.28|1.59|0.29|0.285||14,000 |1.55|0.27|1.60|0.30|0.285
9 |16,000|1.54|0.32|1.63|0.33|0.325||16,000 |1.59|0.31|1.64|0.34|0.325
10 |18,000|1.58|0.36|1.68|0.38|0.370||18,000 |1.62|0.34|1.69|0.39|0.365
11 |20,000|1.61|0.39|1.72|0.42|0.405||20,000 |1.66|0.38|1.74|0.44|0.410
12 |22,000|1.66|0.44|1.76|0.46|0.450||22,000 |1.71|0.43|1.80|0.50|0.465
13 |24,000|1.81|0.59|1.81|0.51|0.550||24,000 |1.77|0.49|1.84|0.54|0.515
14 |26,000|1.86|0.64|1.86|0.56|0.600||26,000 |1.83|0.55|1.90|0.60|0.575
15 |28,000|1.91|0.69|1.91|0.61|0.650||28,000 |1.90|0.62|1.97|0.67|0.645
16 |30,000|1.96|0.74|1.96|0.66|0.700||30,000 |1.97|0.69|2.02|0.72|0.705
17 |32,000|2.00|0.78|2.02|0.72|0.750||32,000 |2.12|0.84|2.10|0.80|0.820
18 |34,000|2.04|0.82|2.11|0.81|0.815||34,000 |2.20|0.92|2.16|0.86|0.885
19 |36,000|2.10|0.88|2.20|0.90|0.890||36,000 |2.29|1.01|2.24|0.94|0.975
20 |38,000|2.16|0.94|2.25|0.95|0.945||38,000 |2.39|1.11|2.32|1.02|1.065
21 |40,000|2.28|1.06|2.38|1.08|1.070||
22 |42,000|2.38|1.16|2.42|1.12|1.140||
23 |44,000|2.44|1.22|2.52|1.22|1.220||
24 |46,000|2.53|1.31|2.60|1.30|1.305||
25 |48,000|2.66|1.44|2.71|1.41|1.425||
26 |50,000|2.78|1.56|2.87|1.57|1.565||
||
33,000 lb., First Crack; ||24,000 lb., First Crack;
51,330 lb., Failed. ||44,000 lb., Failed.
||
At Elastic Limit: Load, 22,000 lb.; ||At Elastic Limit: Load, 20,000 lb.;
deflection, 0.45 in.; || deflection, 0.41 in.;
S, 3,484 lb. || S, 3,018 lb.
||
Maximum: Load, 51,330 lb.; ||Maximum: Load, 44,000 lb.;
deflection,.....; || deflection,.....;
S, 8,925 lb. || S, 6,627 lb.
||
E = 1,695,000 lb. || E = 1,625,000 lb.
=========================================================================
TABLE 4.--(Continued.)--LOAD AND DEFLECTION LOG. BEAM VII.
Columns in table:
A: Load, in pounds.
B: Reading.
C: Total deflection.
D: Mean total deflection.
Date: March 2d, 1909. Date: February 20th, 1909. l = 12 ft.; l = 12 ft.; b (mean) = 6.56 in.; b (mean) = 6.22 in.; h (mean) = 15.62 in.; h (mean) = 15.62 in.; c = 7.81 in. c = 7.81 in.
Time = 1 hr. Time = 33 min.
| P | DEFLECTION, IN INCHES. || P | DEFLECTION, IN INCHES.
No.+------+----+----+----+----+-----++---------+----+----+----+----+-----
| A | B | C | B | C | D || A | B | C | B | C | D
---+------+----+----+----+----+-----++---------+----+----+----+----+-----
1 | 0 |1.84| 0 |1.71| 0 | 0 || 0 |1.69| 0 |1.73| 0 | 0
2 | 2,000|1.88|0.04|1.74|0.03|0.035|| 2,000 |1.72|0.03|1.77|0.04|0.035
3 | 4,000|1.92|0.08|1.79|0.08|0.080|| 4,000 |1.76|0.07|1.80|0.07|0.070
4 | 6,000|1.96|0.12|1.81|0.10|0.110|| 6,000 |1.80|0.11|1.84|0.11|0.110
5 | 8,000|2.00|0.16|1.85|0.14|0.150|| 8,000 |1.84|0.15|1.87|0.14|0.145
6 |10,000|2.03|0.19|1.89|0.18|0.185||10,000 |1.88|0.19|1.92|0.19|0.190
7 |12,000|2.06|0.22|1.93|0.22|0.220||12,000 |1.91|0.22|1.95|0.22|0.220
8 |14,000|2.11|0.27|1.95|0.24|0.255||14,000 |1.95|0.26|2.00|0.27|0.265
9 |16,000|2.14|0.30|1.99|0.28|0.290||16,000 |1.99|0.30|2.03|0.30|0.300
10 |18,000|2.18|0.34|2.03|0.32|0.330||18,000 |2.03|0.34|2.06|0.33|0.335
11 |20,000|2.22|0.38|2.05|0.34|0.360||20,000 |2.07|0.38|2.11|0.38|0.380
12 |22,000|2.25|0.41|2.10|0.39|0.400||22,000 |2.11|0.42|2.16|0.43|0.425
13 |24,000|2.29|0.45|2.13|0.42|0.435||24,000 |2.15|0.46|2.20|0.47|0.465
14 |26,000|2.32|0.48|2.17|0.46|0.470||26,000 |2.19|0.50|2.24|0.51|0.505
15 |28,000|2.36|0.52|2.21|0.50|0.510||28,000 |2.23|0.54|2.28|0.55|0.545
16 |30,000|2.40|0.56|2.25|0.54|0.550||30,000 |2.27|0.58|2.33|0.60|0.590
17 |32,000|2.43|0.59|2.29|0.58|0.585||32,000 |2.32|0.63|2.37|0.64|0.635
18 |34,000|2.47|0.63|2.32|0.61|0.620||34,000 |2.36|0.67|2.42|0.69|0.680
19 |36,000|2.51|0.67|2.37|0.66|0.665||36,000 |
20 |38,000|2.56|0.72|2.41|0.70|0.710||
||
27,000 lb., First Crack; ||28,000 lb., First Crack;
51,900 lb., Failed. ||49,000 lb., Failed.
||
At Elastic Limit: Load, 34,000 lb.; ||At Elastic Limit: Load, 20,000 lb.;
deflection, 0.62 in.; || deflection, 0.38 in.;
S, 4,580 lb. || S, 2,845 lb.
||
Maximum: Load, 51,900 lb.; ||Maximum: Load, 49,000 lb.;
deflection,.....; || deflection,.....;
S, 6,985 lb. || S, 6,970 lb.
||
E = 1,637,000 lb. || E = 1,658,000 lb.
##
Edition notice Project Gutenberg source, credits & licence
The reading text above is the public-domain work. The Project Gutenberg header, production credits and licence are kept here as provenance rather than shown before the book.
Transcriber and production notes
Produced by Juliet Sutherland, Sigal Alon and the Online Distributed Proofreading Team at http://www.pgdp.net
Front matter as received (title page, contents)
[Transcriber's Note: 1. Mathematical power (superscript) is rendered using a carat (^). 2. Superscript text is rendered using an underscore (_).] AMERICAN SOCIETY OF CIVIL ENGINEERS
Header as received
The Project Gutenberg eBook of Transactions of the American Society of Civil Engineers, vol. LXX, Dec. 1910
This eBook is for the use of anyone anywhere in the United States and
most other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg License included with this eBook or online
at www.gutenberg.org. If you are not located in the United States,
you will have to check the laws of the country where you are located
before using this eBook.
Title: Transactions of the American Society of Civil Engineers, vol. LXX, Dec. 1910
Author: W. B. Gregory
Release date: February 16, 2006 [eBook #17776]
Language: English
Other information and formats: www.gutenberg.org/ebooks/17776
Credits: Produced by Juliet Sutherland, Sigal Alon and the Online
Distributed Proofreading Team at http://www.pgdp.netFull Project Gutenberg licence
Updated editions will replace the previous one—the old editions will
be renamed.
Creating the works from print editions not protected by U.S. copyright
law means that no one owns a United States copyright in these works,
so the Foundation (and you!) can copy and distribute it in the United
States without permission and without paying copyright
royalties. Special rules, set forth in the General Terms of Use part
of this license, apply to copying and distributing Project
Gutenberg™ electronic works to protect the PROJECT GUTENBERG™
concept and trademark. Project Gutenberg is a registered trademark,
and may not be used if you charge for an eBook, except by following
the terms of the trademark license, including paying royalties for use
of the Project Gutenberg trademark. If you do not charge anything for
copies of this eBook, complying with the trademark license is very
easy. You may use this eBook for nearly any purpose such as creation
of derivative works, reports, performances and research. Project
Gutenberg eBooks may be modified and printed and given away—you may
do practically ANYTHING in the United States with eBooks not protected
by U.S. copyright law. Redistribution is subject to the trademark
license, especially commercial redistribution.
START: FULL LICENSE
THE FULL PROJECT GUTENBERG™ LICENSE
PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK
To protect the Project Gutenberg™ mission of promoting the free
distribution of electronic works, by using or distributing this work
(or any other work associated in any way with the phrase “Project
Gutenberg”), you agree to comply with all the terms of the Full
Project Gutenberg License available with this file or online at
www.gutenberg.org/license.
Section 1. General Terms of Use and Redistributing Project Gutenberg
electronic works
1.A. By reading or using any part of this Project Gutenberg
electronic work, you indicate that you have read, understand, agree to
and accept all the terms of this license and intellectual property
(trademark/copyright) agreement. If you do not agree to abide by all
the terms of this agreement, you must cease using and return or
destroy all copies of Project Gutenberg electronic works in your
possession. If you paid a fee for obtaining a copy of or access to a
Project Gutenberg electronic work and you do not agree to be bound
by the terms of this agreement, you may obtain a refund from the person
or entity to whom you paid the fee as set forth in paragraph 1.E.8.
1.B. “Project Gutenberg” is a registered trademark. It may only be
used on or associated in any way with an electronic work by people who
agree to be bound by the terms of this agreement. There are a few
things that you can do with most Project Gutenberg electronic works
even without complying with the full terms of this agreement. See
paragraph 1.C below. There are a lot of things you can do with Project
Gutenberg electronic works if you follow the terms of this
agreement and help preserve free future access to Project Gutenberg
electronic works. See paragraph 1.E below.
1.C. The Project Gutenberg Literary Archive Foundation (“the
Foundation” or PGLAF), owns a compilation copyright in the collection
of Project Gutenberg electronic works. Nearly all the individual
works in the collection are in the public domain in the United
States. If an individual work is unprotected by copyright law in the
United States and you are located in the United States, we do not
claim a right to prevent you from copying, distributing, performing,
displaying or creating derivative works based on the work as long as
all references to Project Gutenberg are removed. Of course, we hope
that you will support the Project Gutenberg mission of promoting
free access to electronic works by freely sharing Project Gutenberg
works in compliance with the terms of this agreement for keeping the
Project Gutenberg name associated with the work. You can easily
comply with the terms of this agreement by keeping this work in the
same format with its attached full Project Gutenberg License when
you share it without charge with others.
1.D. The copyright laws of the place where you are located also govern
what you can do with this work. Copyright laws in most countries are
in a constant state of change. If you are outside the United States,
check the laws of your country in addition to the terms of this
agreement before downloading, copying, displaying, performing,
distributing or creating derivative works based on this work or any
other Project Gutenberg work. The Foundation makes no
representations concerning the copyright status of any work in any
country other than the United States.
1.E. Unless you have removed all references to Project Gutenberg:
1.E.1. The following sentence, with active links to, or other
immediate access to, the full Project Gutenberg License must appear
prominently whenever any copy of a Project Gutenberg work (any work
on which the phrase “Project Gutenberg” appears, or with which the
phrase “Project Gutenberg” is associated) is accessed, displayed,
performed, viewed, copied or distributed:
This eBook is for the use of anyone anywhere in the United States and most
other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg™ License included with this eBook or online
at www.gutenberg.org. If you
are not located in the United States, you will have to check the laws
of the country where you are located before using this eBook.
1.E.2. If an individual Project Gutenberg electronic work is
derived from texts not protected by U.S. copyright law (does not
contain a notice indicating that it is posted with permission of the
copyright holder), the work can be copied and distributed to anyone in
the United States without paying any fees or charges. If you are
redistributing or providing access to a work with the phrase “Project
Gutenberg” associated with or appearing on the work, you must comply
either with the requirements of paragraphs 1.E.1 through 1.E.7 or
obtain permission for the use of the work and the Project Gutenberg
trademark as set forth in paragraphs 1.E.8 or 1.E.9.
1.E.3. If an individual Project Gutenberg electronic work is posted
with the permission of the copyright holder, your use and distribution
must comply with both paragraphs 1.E.1 through 1.E.7 and any
additional terms imposed by the copyright holder. Additional terms
will be linked to the Project Gutenberg License for all works
posted with the permission of the copyright holder found at the
beginning of this work.
1.E.4. Do not unlink or detach or remove the full Project Gutenberg
License terms from this work, or any files containing a part of this
work or any other work associated with Project Gutenberg.
1.E.5. Do not copy, display, perform, distribute or redistribute this
electronic work, or any part of this electronic work, without
prominently displaying the sentence set forth in paragraph 1.E.1 with
active links or immediate access to the full terms of the Project
Gutenberg License.
1.E.6. You may convert to and distribute this work in any binary,
compressed, marked up, nonproprietary or proprietary form, including
any word processing or hypertext form. However, if you provide access
to or distribute copies of a Project Gutenberg work in a format
other than “Plain Vanilla ASCII” or other format used in the official
version posted on the official Project Gutenberg website
(www.gutenberg.org), you must, at no additional cost, fee or expense
to the user, provide a copy, a means of exporting a copy, or a means
of obtaining a copy upon request, of the work in its original “Plain
Vanilla ASCII” or other form. Any alternate format must include the
full Project Gutenberg License as specified in paragraph 1.E.1.
1.E.7. Do not charge a fee for access to, viewing, displaying,
performing, copying or distributing any Project Gutenberg works
unless you comply with paragraph 1.E.8 or 1.E.9.
1.E.8. You may charge a reasonable fee for copies of or providing
access to or distributing Project Gutenberg electronic works
provided that:
• You pay a royalty fee of 20% of the gross profits you derive from
the use of Project Gutenberg works calculated using the method
you already use to calculate your applicable taxes. The fee is owed
to the owner of the Project Gutenberg trademark, but he has
agreed to donate royalties under this paragraph to the Project
Gutenberg Literary Archive Foundation. Royalty payments must be paid
within 60 days following each date on which you prepare (or are
legally required to prepare) your periodic tax returns. Royalty
payments should be clearly marked as such and sent to the Project
Gutenberg Literary Archive Foundation at the address specified in
Section 4, “Information about donations to the Project Gutenberg
Literary Archive Foundation.”
• You provide a full refund of any money paid by a user who notifies
you in writing (or by e-mail) within 30 days of receipt that s/he
does not agree to the terms of the full Project Gutenberg™
License. You must require such a user to return or destroy all
copies of the works possessed in a physical medium and discontinue
all use of and all access to other copies of Project Gutenberg™
works.
• You provide, in accordance with paragraph 1.F.3, a full refund of
any money paid for a work or a replacement copy, if a defect in the
electronic work is discovered and reported to you within 90 days of
receipt of the work.
• You comply with all other terms of this agreement for free
distribution of Project Gutenberg™ works.
1.E.9. If you wish to charge a fee or distribute a Project
Gutenberg™ electronic work or group of works on different terms than
are set forth in this agreement, you must obtain permission in writing
from the Project Gutenberg Literary Archive Foundation, the manager of
the Project Gutenberg™ trademark. Contact the Foundation as set
forth in Section 3 below.
1.F.
1.F.1. Project Gutenberg volunteers and employees expend considerable
effort to identify, do copyright research on, transcribe and proofread
works not protected by U.S. copyright law in creating the Project
Gutenberg™ collection. Despite these efforts, Project Gutenberg™
electronic works, and the medium on which they may be stored, may
contain “Defects,” such as, but not limited to, incomplete, inaccurate
or corrupt data, transcription errors, a copyright or other
intellectual property infringement, a defective or damaged disk or
other medium, a computer virus, or computer codes that damage or
cannot be read by your equipment.
1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right
of Replacement or Refund” described in paragraph 1.F.3, the Project
Gutenberg Literary Archive Foundation, the owner of the Project
Gutenberg™ trademark, and any other party distributing a Project
Gutenberg™ electronic work under this agreement, disclaim all
liability to you for damages, costs and expenses, including legal
fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGE.
1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
defect in this electronic work within 90 days of receiving it, you can
receive a refund of the money (if any) you paid for it by sending a
written explanation to the person you received the work from. If you
received the work on a physical medium, you must return the medium
with your written explanation. The person or entity that provided you
with the defective work may elect to provide a replacement copy in
lieu of a refund. If you received the work electronically, the person
or entity providing it to you may choose to give you a second
opportunity to receive the work electronically in lieu of a refund. If
the second copy is also defective, you may demand a refund in writing
without further opportunities to fix the problem.
1.F.4. Except for the limited right of replacement or refund set forth
in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO
OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
1.F.5. Some states do not allow disclaimers of certain implied
warranties or the exclusion or limitation of certain types of
damages. If any disclaimer or limitation set forth in this agreement
violates the law of the state applicable to this agreement, the
agreement shall be interpreted to make the maximum disclaimer or
limitation permitted by the applicable state law. The invalidity or
unenforceability of any provision of this agreement shall not void the
remaining provisions.
1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
trademark owner, any agent or employee of the Foundation, anyone
providing copies of Project Gutenberg™ electronic works in
accordance with this agreement, and any volunteers associated with the
production, promotion and distribution of Project Gutenberg™
electronic works, harmless from all liability, costs and expenses,
including legal fees, that arise directly or indirectly from any of
the following which you do or cause to occur: (a) distribution of this
or any Project Gutenberg work, (b) alteration, modification, or
additions or deletions to any Project Gutenberg work, and (c) any
Defect you cause.
Section 2. Information about the Mission of Project Gutenberg
Project Gutenberg is synonymous with the free distribution of
electronic works in formats readable by the widest variety of
computers including obsolete, old, middle-aged and new computers. It
exists because of the efforts of hundreds of volunteers and donations
from people in all walks of life.
Volunteers and financial support to provide volunteers with the
assistance they need are critical to reaching Project Gutenberg’s
goals and ensuring that the Project Gutenberg collection will
remain freely available for generations to come. In 2001, the Project
Gutenberg Literary Archive Foundation was created to provide a secure
and permanent future for Project Gutenberg and future
generations. To learn more about the Project Gutenberg Literary
Archive Foundation and how your efforts and donations can help, see
Sections 3 and 4 and the Foundation information page at www.gutenberg.org.
Section 3. Information about the Project Gutenberg Literary Archive Foundation
The Project Gutenberg Literary Archive Foundation is a non-profit
501(c)(3) educational corporation organized under the laws of the
state of Mississippi and granted tax exempt status by the Internal
Revenue Service. The Foundation’s EIN or federal tax identification
number is 64-6221541. Contributions to the Project Gutenberg Literary
Archive Foundation are tax deductible to the full extent permitted by
U.S. federal laws and your state’s laws.
The Foundation’s business office is located at 41 Watchung Plaza #516,
Montclair NJ 07042, USA, +1 (862) 621-9288. Email contact links and up
to date contact information can be found at the Foundation’s website
and official page at www.gutenberg.org/contact
Section 4. Information about Donations to the Project Gutenberg
Literary Archive Foundation
Project Gutenberg™ depends upon and cannot survive without widespread
public support and donations to carry out its mission of
increasing the number of public domain and licensed works that can be
freely distributed in machine-readable form accessible by the widest
array of equipment including outdated equipment. Many small donations
($1 to $5,000) are particularly important to maintaining tax exempt
status with the IRS.
The Foundation is committed to complying with the laws regulating
charities and charitable donations in all 50 states of the United
States. Compliance requirements are not uniform and it takes a
considerable effort, much paperwork and many fees to meet and keep up
with these requirements. We do not solicit donations in locations
where we have not received written confirmation of compliance. To SEND
DONATIONS or determine the status of compliance for any particular state
visit www.gutenberg.org/donate.
While we cannot and do not solicit contributions from states where we
have not met the solicitation requirements, we know of no prohibition
against accepting unsolicited donations from donors in such states who
approach us with offers to donate.
International donations are gratefully accepted, but we cannot make
any statements concerning tax treatment of donations received from
outside the United States. U.S. laws alone swamp our small staff.
Please check the Project Gutenberg web pages for current donation
methods and addresses. Donations are accepted in a number of other
ways including checks, online payments and credit card donations. To
donate, please visit: www.gutenberg.org/donate.
Section 5. General Information About Project Gutenberg electronic works
Professor Michael S. Hart was the originator of the Project
Gutenberg concept of a library of electronic works that could be
freely shared with anyone. For forty years, he produced and
distributed Project Gutenberg eBooks with only a loose network of
volunteer support.
Project Gutenberg eBooks are often created from several printed
editions, all of which are confirmed as not protected by copyright in
the U.S. unless a copyright notice is included. Thus, we do not
necessarily keep eBooks in compliance with any particular paper
edition.
Most people start at our website which has the main PG search
facility: www.gutenberg.org.
This website includes information about Project Gutenberg,
including how to make donations to the Project Gutenberg Literary
Archive Foundation, how to help produce our new eBooks, and how to
subscribe to our email newsletter to hear about new eBooks.Source: Project Gutenberg ebook #17776. Public-domain status is recorded per item; the licence text above is reproduced unchanged.